554882
7
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
GD-04 DAVID 7 MKS51202_OS1*
11.2.1. DTMF relay control
Call David’s tel. number. After about 7 seconds, David responds with a beep on the line
(this means that the call has been answered) followed by relay X and Y status indication (in
this order): 2 short beeps = OFF, 1 long beep = ON.
Enter the DTMF code. A relay switch-on is confirmed by a long beep, a switch-off by two short beeps.
Terminate the call (David automatically terminates the call after 60 seconds).
After the call has been terminated David reports the current relay status via SMS.
Note: Too weak a GSM signal in David’s or your location may result in DTMF control
malfunctions.
11.3. The GD-04R radio module
By plugging the GD-04R radio module into the digital bus connector (after the power supply has
been disconnected) your David acquires the following capabilities:
Relay X and Y state transmission to UC or AC OASiS wireless
receivers.
Input A to D activations via RC-8x OASiS wireless buttons or via JA-
8x OASiS wireless detectors.
Relay X or Y control via RC-8x OASiS wireless buttons.
Relay X or Y control via a TP-8x wireless thermostat.
The module has a built-in internal antenna. If necessary, a Jablotron
external antenna of type AN-80 or AN-81 can be applied to extend David’s
working range.
Note: The external antenna is essential when the GD-04A back-up module is used.
11.3.1. Transmitting X or Y relay status to an UC-82 or AC-82 receiver
Enter mode 4 on the receiver and press the XY button on David’s GD-04R module. This
establishes a connection so that the receiver’s relay status mirrors David’s relay status. There is
no limit to the number of UC/AC receivers which can be connected this way.
11.3.2. Wireless device input assignment and operation
Each input A to D can have one OASiS wireless device assigned to it. This way, triggering an
external wireless device has the same effect as GD-04 input activation by physical connection to
GND, effectively making the inputs radio-signal-activated.
Take the following steps to enroll a device:
1. Press and hold the ABCD button on the GD-04R module.
2. Entering enrollment mode is indicated after 5 seconds by flashing of the LED on the
GD-04R module – release the button.
3. Enroll up to 4 wireless devices to the GD-04R (send enrollment signals to the module). The
first device is assigned to the A input, the second one to the B input, etc. Wireless buttons
are enrolled by pressing them, wireless detectors by inserting their batteries. Enrollment is
confirmed by a long flash from the LED on the GD-04R.
Important: Enrolling the first device erases all the previously enrolled devices. Thus all
the desired devices should be enrolled in a single enrollment session.
4. Exit enrollment mode by pressing the ABCD button (enrollment is automatically terminated
after the fourth device has been assigned or after 40 seconds).
5. After enrollment mode termination, the LED on the module lights for approx. 5 seconds to
indicate enrollment data storage.
Notes:
If the two buttons A and B are present on an RC-8x controller, the device can be enrolled by
pressing either A, B or A+B. The operational logic is then as follows: pressing A or A+B is
A
BCDXY
GD-04R
module
remove it if
external antenna
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron GD-04 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron GD-04 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info