554988
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
The CA-550 tilt detector 2/2 MGX51010
The CA-550 tilt detector installation, operation manual
The CA-550 tilt detector detects movement of the car in two
axes (x and y). No mechanical parts are used in the detector.
Detection is achieved through electronic acceleration metering.
The digital analysis used in this detector ensures high
resistance against the false alarms. When the alarm is armed
(power supply connected) the reference position of the detector
is stored in the memory after which the position of the detector is
continuously checked, compared and updated. If the tilt of the
car is changed by more than 1
°, the detector will be triggered.
Specification:
Power 9 - 16V (DC)
Power consumption typ.1 mA
Operating temperature -40 °C to +85 °C
Maximum sensitivity (for both axes) 1° (built-in digital filter)
Angle of operation with max. sensitivity preservation ± 45° from reference (horizontal) position
Installation position of the detector ± 15° from horizontal (both axes)
Output negative pulse with a duration of 0.5 s
Maximal output load 80 mA
The CA-550 complies with the essential requirements of: 95/56/EC Directive relating to devices
to prevent the unauthorized use of motor vehicles and
89/336/EC EMC Directive - Protection
concerning electromagnetic compatibility when is used for its intended purpose
Wiring:
Red Power supply + 12V. It can be connected either permanently to +12V, or to the switching
output of the alarm (where +12V is present when the alarm is armed).
Black GND connect to the original grounding of the car.
White Output - if the detector is triggered the output will be connected to GND for 0.5 sec. It is
short-circuit protected. The output should be connected to the external detector input of
the car alarm.
Installation:
The CA-550 tilt detector should be installed on the floor in the interior of the car where there is no danger
of mechanical damage or high humidity (the lowest part of the floor). Fix it using a double sided Velcro
sticker or by screws. The detector must be installed in a horizontal position with a maximal deviation of ± 15°
in both axis (x and y). If the detector is fixed by a screw, only one bigger hole in the middle of the detector
should be used. The smaller holes in the corners of the detector are not designed for this purpose. The
screw should be tightened carefully so as not to damage the housing of the detector.
Function:
When the alarm is armed (power supply connected) the reference position of the detector will be stored in the
memory (max 30 seconds). The position of the detector is continuously checked, compared and updated. If the
tilt changes by more then 1
°, the output will be switched to ground for 0.5 sec. Default parameters are re-set
after detector activation. It can take up to 30 seconds (depends on the amount of detected tilt). If the maximum
output load of 80 mA is exceeded, the electronic fuse will temporarily switch off the output. A built-in digital filter
ensures that the detector will not be triggered by a short tilt of the car, caused, for example, by sudden burst of
wind after which the car will return to its original position.
Maintenance
The device does not require any special maintenance. To check correct functioning, we recommend
triggering an intentional alarm from time to time.
Note: Although this product does not contain any harmful materials we suggest you to
return the product to the dealer or directly to the producer after usage.
The CA-550 tilt detector 2/2 MGX51010
The CA-550 tilt detector installation, operation manual
The CA-550 tilt detector detects movement of the car in two
axes (x and y). No mechanical parts are used in the detector.
Detection is achieved through electronic acceleration metering.
The digital analysis used in this detector ensures high
resistance against the false alarms. When the alarm is armed
(power supply connected) the reference position of the detector
is stored in the memory after which the position of the detector is
continuously checked, compared and updated. If the tilt of the
car is changed by more than 1
°, the detector will be triggered.
Specification:
Power 9 - 16V (DC)
Power consumption typ.1 mA
Operating temperature -40 °C to +85 °C
Maximum sensitivity (for both axes) 1° (built-in digital filter)
Angle of operation with max. sensitivity preservation ± 45° from reference (horizontal) position
Installation position of the detector ± 15° from horizontal (both axes)
Output negative pulse with a duration of 0.5 s
Maximal output load 80 mA
The CA-550 complies with the essential requirements of: 95/56/EC Directive relating to devices
to prevent the unauthorized use of motor vehicles and
89/336/EC EMC Directive - Protection
concerning electromagnetic compatibility when is used for its intended purpose
Wiring:
Red Power supply + 12V. It can be connected either permanently to +12V, or to the switching
output of the alarm (where +12V is present when the alarm is armed).
Black GND connect to the original grounding of the car.
White Output - if the detector is triggered the output will be connected to GND for 0.5 sec. It is
short-circuit protected. The output should be connected to the external detector input of
the car alarm.
Installation:
The CA-550 tilt detector should be installed on the floor in the interior of the car where there is no danger
of mechanical damage or high humidity (the lowest part of the floor). Fix it using a double sided Velcro
sticker or by screws. The detector must be installed in a horizontal position with a maximal deviation of ± 15°
in both axis (x and y). If the detector is fixed by a screw, only one bigger hole in the middle of the detector
should be used. The smaller holes in the corners of the detector are not designed for this purpose. The
screw should be tightened carefully so as not to damage the housing of the detector.
Function:
When the alarm is armed (power supply connected) the reference position of the detector will be stored in the
memory (max 30 seconds). The position of the detector is continuously checked, compared and updated. If the
tilt changes by more then 1
°, the output will be switched to ground for 0.5 sec. Default parameters are re-set
after detector activation. It can take up to 30 seconds (depends on the amount of detected tilt). If the maximum
output load of 80 mA is exceeded, the electronic fuse will temporarily switch off the output. A built-in digital filter
ensures that the detector will not be triggered by a short tilt of the car, caused, for example, by sudden burst of
wind after which the car will return to its original position.
Maintenance
The device does not require any special maintenance. To check correct functioning, we recommend
triggering an intentional alarm from time to time.
Note: Although this product does not contain any harmful materials we suggest you to
return the product to the dealer or directly to the producer after usage.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CA-550 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CA-550 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info