Handleiding JVC SP-UXN1 (pagina 1 van 2) (Engels)

56316

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

SPEAKERS

PHONES

RIGHT

IMPEDANCE

MIN

LEFT

ANTENNA

COAXIAL

AM EXT

LOOP

MICRO COMPONENT SYSTEM

UX-N1S

—Consists of CA-UXN1S and SP-UXN1S

UX-N1W

—Consists of CA-UXN1W and SP-UXN1W

INSTRUCTIONS

GNT0065-001B[B]

0106MOCMDWJSC

1 3

2 4

Connections

Do not connect the AC power cord until all other connections have been made.

Basic and Common Operations

This System can play back the following discs—regular CD and CD-R/CD-RW (recorded either in the audio CD or MP3 format).

• When playing back the MP3 track, MP3 indicator appears on the display.

To Set a Disc

On the System

2 3

On the System

The disc cover on the

System opens.

Place a disc correctly with its label side up, then

press down on the portions around the disc’s

center hole until you hear a click.

• When removing the disc, take out the disc

by holding it at the edge with pressing the

System’s pivot lightly.

The disc cover on the

System closes.

• Do not close forcibly

the disc cover with

the hand.

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If

the plug ﬁ tted is not suitable for the power points in your

home or the cable is too short to reach a power point,

then obtain an appropriate safety approved extension lead

or consult your dealer.

BE SURE to replace the fuse only with an identical

approved type, as originally ﬁ tted.

If nonetheless the mains plug is cut oﬀ ensure to remove

the fuse and dispose of the plug immediately, to avoid a

possible shock hazard by inadvertent connection to the

mains supply.

If this product is not supplied ﬁ tted with a mains plug then

follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is

marked with the letter E or by the safety earth symbol or

coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in

accordance with the following code:

Blue: Neutral

Brown: Live

As these colours may not correspond with the coloured

markings identifying the terminals in your plug proceed as

follows:

The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or coloured

red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Warnings, Cautions and Others

Caution —

button!

Disconnect the mains plug to shut the power oﬀ completely.

When installing the apparatus, ensure that the plug is easily

accessible.

The button in any position does not disconnect the

mains line. The power can be remote controlled.

• When the unit is on standby, the STANDBY lamp lights red.

• When the unit is turned on, the STANDBY lamp goes oﬀ .

CAUTION

To reduce the risk of electrical shocks, ﬁ re, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

Information for Users on Disposal of Old Equipment

[European Union only]

This symbol indicates that the product with this symbol should not be disposed as general household waste. If

you want to dispose of this equipment, please do not use the ordinary dust bin! There is a separate collection

System for these products.

CAUTION: Proper Ventilation

To avoid risk of electric shock and ﬁ re, and to prevent damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of

10 cm or more.

Front view Side view

15 cm

10 cm

15 cm

1 cm

15 cm

1 cm

SP-UXN1S/SP-UXN1W CA-UXN1S/CA-UXN1W SP-UXN1S/SP-UXN1W CA-UXN1S/CA-UXN1W

About the cooling fan

A cooling fan is mounted on the rear panel of the unit to prevent abnormal temperature inside the unit, thus assuring

normal operation of the unit.

Supplied Accessories

After unpacking, check to be sure that you have all the

following items. The number in parentheses indicates the

quantity of each piece supplied.

• Remote control (x 1)

• Lithium coin battery CR2025 (x 1) (The battery has been

installed when shipped from the factory.)

• AM loop antenna (x 1)

• FM antenna (x 1)

If anything is missing, consult your dealer immediately.

To a wall outlet

Plug the AC power cord only after

all connections are complete.

AM loop antenna

(supplied)

Turn it until the best

reception is obtained.

To assemble the AM loop antenna

To connect the AM loop antenna

To connect the speaker cords

Make sure the both speakers are connected correctly and

ﬁ rmly.

When connecting the speaker cords, match the polarity of

the speaker terminals: white cord to (+) and white cord with

black stripe to (–).

NOTES

• DO NOT connect more than one speaker

to each terminal.

• DO NOT allow the conductor of the

speaker cords to be in touch with the

metallic parts of the System.

NOTES

• Make sure the antenna conductors do not touch any other terminals,

connecting cords and power cord. Also, keep the antennas away from

metallic parts of the System, connecting cords, and the AC power cord.

This could cause poor reception.

• If the cords are covered with vinyl, remove the vinyl to expose the tip

of the cord by twisting the vinyl.

Programming the Playing Order—Program

Play (except for MP3)

Press repeatedly until the PRGM (program) indicator

appears on the display before you start playback.

or Select the track number to program.

Press to program the selected track.

Repeat step 2 and 3 to program other tracks you want.

• If you try to program a 33rd track, “FULL” will appear on the

display.

The tracks are played in the order you have

programmed.

Operations on the Program Play Mode

To Pr ess

Check the

programmed

contents

Press while playback is stopped.

To erase the

last step

To erase

the entire

program

Press while playback is stopped.

To exit from

program play

Press twice while playback is

stopped to exit from the program

play.

• The stored program is erased.

Playing at Random—Random Play

Press until the RND (random) indicator appears on

the display before you start playback.

Playback starts in random order.

Random Play ends when all tracks are played.

Operations on the Random Play Mode

To Pr ess

To skip a track

•

does not work.

To exit from

random play

Press once while playback is

stopped to exit from the random

play.

Playing Repeatedly—Repeat Play

Press repeatedly before you start playback to specify

the repeat mode as follows:

REP 1 REP GRP

(MP3 only)

REP OFF REP ALL

REP 1

Repeats the current (or speciﬁ ed)

track.

REP GRP

Repeats all tracks in the current

group. (MP3 only)

REP ALL Repeats all tracks.

REP OFF Normal playback

Basic Disc Operations

Press

On the

System

On the

remote

Playback the disc

Current track number and elapsed playing

time appear on the main display.

• During playback, press again to stop

playing for a moment.

Stop playback

• While playback is stopped, total track

number and total playing time (for MP3

disc, group number and track number)

appear on the main display.

Select a track

Increases the track numbers.

Decreases the track numbers.

Select a group (MP3

only)

—

Increases the group numbers while playback

is stopped.

—

Decreases the group numbers while playback

is stopped.

Forward search /

Reverse search

—

Fast-forwards the track by pressing brieﬂ y.

To stop searching, press

—

Fast-reverses the track by pressing brieﬂ y.

To stop searching, press

NOTES

• If the disc cannot be read correctly (because it is scratched, for example) or an unreadable CD-R or

CD-RW is loaded, playback will not start.

• If no disc is inserted, “NO DISC” appears on the main display.

Precautions

Notes on the power cord

• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet. A small

amount of power (3.6 W) is always consumed while the power cord is connected to the wall outlet.

• When unplugging the System from the wall outlet, always pull the plug, not the power cord.

• Do not handle the power cord with wet hands.

• Disconnect the power cord before cleaning the System or moving the System.

• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause ﬁ re, electric shock, or other accidents.

• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.

Avoid moisture, water, dust, and high temperatures

• Do not place the System in moist or dusty places.

• If water gets inside the System, turn oﬀ the power and remove the plug from the wall outlet, then consult your dealer. Using

the System in this state may cause a ﬁ re or electrical shock.

• Do not expose the System to direct sunlight or place it near a heating device.

Notes on installation

• Select a place which is level, dry and neither too hot nor too cold between 5˚C and 35˚C.

• Do not install the System in a place subject to vibrations.

• Do not put heavy objects on the System.

To prevent malfunction or damage of the System

• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.

• Do not block the vents.

To clean the cabinet

• Use a soft cloth. Follow the relevant instructions on the use of chemically-coated cloths.

• Do not use benzene, thinner or other organic solvents and disinfectants. These may cause deformation or discoloring.

There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult

your dealer.

Hold

Insert

Release

Outdoor FM antenna

(not supplied)

For better FM/AM reception

FM antenna (supplied)

Extend it so that you can obtain the best reception.

Getting Started

NOTE

DO NOT turn oﬀ (standby)

the System with the volume

set to an extremely high level;

Otherwise, the sudden blast

of sound can damage your

hearing, speakers and/or

headphones when you turn

on the System or start

playback.

Using Headphones

Be sure to turn down the volume before connecting or wearing

the headphones.

• Connecting the headphones will deactivate the speakers.

Operating on the System

To Pr ess

Turn on or oﬀ (standby) the

power

The standby lamp on the System turns oﬀ /on.

Select a source*

See “Playing Back Discs” on page 4.

See “Listening to FM and AM Broadcasts” on

page 5.

See “Connecting a Portable Audio Device” on

page 6.

Adjust the volume

You can adjust the volume level from level 0

(VOL MIN) to level 31 (VOL MAX).

Operating on the Remote Control

To Pr ess

Turn on or oﬀ

(standby) the power

The standby lamp on the System turns oﬀ /on.

Select a source

See “Playing Back Discs” on page 4.

See “Listening to FM and AM Broadcasts” on

page 5.

See “Connecting a Portable Audio Device” on

page 6.

Adjust the volume

You can adjust the volume level from level 0

(VOL MIN) to level 31 (VOL MAX).

Drop the volume in a

moment

To restore the volume, press again, or adjust

the volume level.

Reinforce the bass

sound

AHB PRO indicator appears on the display.

To cancel this function, press again.

Adjust the tone (Bass/

Treble)

Press once to adjust the bass level or press

twice to adjust the treble level.

Then press VOLUME + to increase the level or

press VOLUME – to decrease it.

• You can adjust the bass and treble level from

–3 to +3.

Changing the display

brightness

Press when the System is turned on.

To cancel this function, press again.

Set the SAVE mode

Press and hold for more than 2 seconds when

the System is on standby.

To cancel this function, press and hold for

more than 2 seconds again.

• Setting the SAVE mode allows you to reduce

power consumption by turning the display

oﬀ while on standby.

Changing the display

information (Clock

and Source)

Press brieﬂ y (except for FM mode).

For setting the clock, see page 7.

Turn oﬀ the System

automatically after CD

playback is over

(AUTO STANDBY

function)

Press and hold until A.STBY indicator appears

on the display.

To cancel this function, press and hold again.

• If no operation is done for about 3 minutes

after CD playback stops, the System turns oﬀ .

Turn oﬀ the System by

using the sleep timer

Press brieﬂ y and repeatedly to specify the time

(in minutes) as follows:

10 20 30 60 90 120 150

Canceled

• To check the time remaining until the shut-oﬀ time after

setting the sleep timer, press SLEEP once.

Point it at the remote sensor on

the front panel. (The operating

range is approx. 7 m.)

Playing Back Discs

Hold

Insert

Release

Disconnect the supplied FM antenna,

and connect to an outdoor FM antenna

using a 75 Ω wire with coaxial type

connector (IEC or DIN45325).

AM loop antenna

Keep it connected.

Vynile-covered wire (not supplied)

Extend it horizontally.

CAUTION:

• Do not block the ventilation openings or holes. (If the

ventilation openings or holes are blocked by a newspaper

or cloth, etc., the heat may not be able to get out.)

• Do not place any naked ﬂ ame sources, such as lighted

candles, on the apparatus.

• When discarding batteries, environmental problems

must be considered and local rules or laws governing the

disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping

or splashing and that no objects ﬁ lled with liquids, such

as vases, shall be placed on the apparatus.

Display Information

Disc play mode indicators (See page 4.)

Tuner mode indicators

(See page 5.)

Timer mode indicators

(See the right column and page 7.)

QP Link indicator

(See page 6.)

Main Display

AHB PRO and A.STBY indicator (See the right column.)

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user

serviceable parts inside the System; leave all servicing to

qualiﬁ ed service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation

when open. Do not view directly with optical instruments.

The model information is located on the bottom.

Prepare the Remote Control

When you use the remote control

for the ﬁ rst time, pull out the

insulation sheet.

Insulation sheet

Replacing the Battery in the Remote Control

Insert the battery into the

remote control by matching the

polarity (+ and –) correctly.

Lithium coin battery

(product number: CR2025)

STANDBY lamp

* You can operate the source select

buttons on the System only touch

lightly, because these buttons are

“touch sensor panel.”

If you touch any one of these

buttons, they lights in blue brieﬂ y.

NOTES

• Store the battery in a place where children cannot reach. If a child accidentally swallows the

battery, consult a doctor immediately.

• Do not recharge, short, disassemble or heat the battery or dispose of it in a ﬁ re. Doing any of

these things may cause the battery to give oﬀ heat, crack, or start a ﬁ re.

• Do not leave the battery with other metallic materials. Doing this may cause the battery to

give oﬀ heat, crack, or start a ﬁ re.

• When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the

battery may start to give oﬀ heat, crack, or start a ﬁ re.

• Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to

give oﬀ heat, crack, or start a ﬁ re.

• Dispose of battery in the proper manner, according to federal, state, and local regulations.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

JVC SP-UXN1 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van JVC SP-UXN1

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info