Connecting To A Satellite Receiver .............44
Connecting/Using A Decoder .....................46
Connecting/Using A Stereo System .............47
SUBSIDIARY SETTINGS 48
Mode Set ....................................................48
Tuner Set ....................................................52
Video Channel Set ......................................58
S
HOW
V
IEW
®
Setup ......................................59
Clock Set ....................................................60
TROUBLESHOOTING 62
QUESTIONS AND ANSWERS 65
SPECIFICATIONS 66
LIST OF TERMS 67
Cov1.fm Page 1 Thursday, March 9, 2000 3:40 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Left-FullColx2
2
EN
Filename [HRS7700EU1.fm]
Page 2March 8, 2000 1:13 pm
SAFETY FIRST
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING:DANGEROUS VOLTAGE INSIDE
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
CAUTION
8
When you are not using the recorder for a long period of time, it is recommended that you disconnect
the power cord from the mains outlet.
8
Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric
shock or fire hazard, remove the power cord from the mains outlet prior to connecting or
disconnecting any signal lead or aerial.
WARNING
There are two different types of SECAM colour systems: SECAM-L, used in FRANCE (also called SECAM-
West), and SECAM-B, used in Eastern European countries (also called SECAM-East).
1. This recorder can also receive SECAM-B colour television signals for recording and playback.
2. Recordings made of SECAM-B television signals produce monochrome pictures if played back on a
video recorder of SECAM-L standard, or do not produce normal colour pictures if played back on a
PAL video recorder with SECAM-B system incorporated (even if the TV set is SECAM-compatible).
3. SECAM-L prerecorded cassettes or recordings made with a SECAM-L video recorder produce
monochrome pictures when played back with this recorder.
4. This recorder cannot be used for the SECAM-L standard. Use a SECAM-L recorder to record SECAM-L
signals.
IMPORTANT
8
Please read the various precautions on page 2 and 3 before installing or operating the recorder.
8
It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without
the consent of the owner of copyright in the sound or video recording, broadcast or cable programme
and in any literary, dramatic, musical, or artistic work embodied therein.
●Cassettes marked “S-VHS” and “VHS” can be used with this video cassette recorder. However, S-VHS recordings are possible only
with cassettes marked “S-VHS”.
By using the S-VHS ET function, it is possible to record and play back with S-VHS picture quality on VHS cassettes with this recorder.
●S
HOW
V
IEW
is a registered trademark of Gemstar Development Corporation. The S
HOW
V
IEW
system is manufactured under licence
from Gemstar Development Corporation.
HRS7700EU1.fm Page 2 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-Full-NoTitle0
EN
3
Filename [HRS7700EU1.fm]
Page 3March 8, 2000 1:13 pm
Failure to heed the following precautions may result in damage to the recorder, remote control or video
cassette.
1. DO NOT place the recorder . . .
...in an environment prone to extreme temperatures or humidity.
...in direct sunlight.
...in a dusty environment.
...in an environment where strong magnetic fields are generated.
...on a surface that is unstable or subject to vibration.
2. DO NOT block the recorder’s ventilation openings.
3. DO NOT place heavy objects on the recorder or remote control.
4. DO NOT place anything which might spill on top of the recorder or remote control.
5. AVOID violent shocks to the recorder during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or
under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold
liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where
condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.
For Italy:
“It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.’95
published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.’95”
The STANDBY/ON
1
button does not completely shut off mains power from the unit, but switches
operating current on and off. “
`
“ shows electrical power standby and “
!
“ shows ON.
Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a
single-speed video recorder.
HRS7700EU1.fm Page 3 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Left-index
4
EN
Filename [HRS7700EU1.fm]
Page 4March 8, 2000 1:13 pm
INDEX
FRONT VIEW
*Attach the provided connector cover when you do not use the front panel connectors.
A
STANDBY/ON
1
Button
墌
pg. 10
B
DIGITAL TBC/NR Button
墌
pg. 21
C
SP/LP Button
墌
pg. 23
D
Cassette Loading Slot
E
Play
4
Button
墌
pg. 18
F
JOG Dial
墌
pg. 19
G
SHUTTLE Ring
墌
pg. 18
H
S-VIDEO Input Connector
墌
pg. 35, 42
I
VIDEO/AUDIO Input Connectors
墌
pg. 35, 40,
42
J
PR +/– Buttons
墌
pg. 23
K
S-VHS ET Button
墌
pg. 25
L
SAT
#
Button
墌
pg. 34
M
Front Display Panel
墌
pg. 5
N
Infrared Beam Receiving Window
O
Record
7
Button
墌
pg. 23
P
Pause
9
Button
墌
pg. 19
Q
INSERT Button
墌
pg. 42
R
Audio Dubbing (A.DUB) Button
墌
pg. 40
S
Stop/Eject
0
Button
墌
pg. 18, 23
REAR VIEW
A
Mains Power Cord
墌
pg. 8
B
S OUT Connector
墌
pg. 9
C
AV1 (L-1) IN/OUT Connector
墌
pg. 8, 38, 44,
45, 46
D
ANT. IN Connector
墌
pg. 8
E
Remote PAUSE Connector
墌
pg. 35
F
AUDIO OUT (L/R) Connectors
墌
pg. 47
G
AV2 (L-2) IN/DECODER Connector
墌
pg. 15,
38, 44, 45, 46
H
SAT CTL Connector
墌
pg. 15
I
RF OUT Connector
墌
pg. 8
HRS7700EU1.fm Page 4 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-index
EN
5
Filename [HRS7700EU1.fm]
Page 5March 8, 2000 1:13 pm
FRONT DISPLAY PANEL
A
B.E.S.T. Picture System Display
墌
pg. 27
Audio Level Indicator
B
Programme Time Indicators
墌
pg. 30
C
Symbolic Mode Indicators
D
“Timer” Indicator
墌
pg. 29, 31
E
S-VHS Indicator
墌
pg. 25, 51
F
Channel/Clock Display
墌
pg. 13
G
Tape Speed Indicators
墌
pg. 23
*EP is for NTSC playback only.
H
Instant REVIEW Indicator
墌
pg. 20
I
Audio Mode Indicator
墌
pg. 22
J
Tape Remaining Time Indicator
墌
pg. 25
K
“Cassette Loaded” Mark
L
VPS/PDC Indicator
墌
pg. 29, 31
M
VCR Indicator
墌
pg. 24
N
Counter/Remain Display
O
Mode Display (L-1, L-2, F-1, S-1 or SAT*)
*When “L-2 SELECT” is set to “SAT” (
墌
pg. 37), “SAT” appears
instead of “L-2”.
PLAY:
FF/REW VARIABLE
SEARCH:
STILL:
SLOW:
RECORD:
RECORD
PAUSE:
AUDIO DUBBING:
AUDIO DUBBING PAUSE:
INSERT:
INSERT PAUSE:
AV INSERT:
AV INSERT PAUSE:
HRS7700EU1.fm Page 5 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
6
EN
Page 6March 8, 2000 6:15 pm
INDEX (cont.)
ON-SCREEN DISPLAY
When “O.S.D.” is set to “ON” (
墌
pg. 49), various operational indicators appear on the TV screen.
A
Operation Mode Indicators
B
Tape Speed SP/LP/EP
*EP is for NTSC playback only.
C
Tape Direction
D
Counter Display
E
Tape Remaining Time Indicator
墌
pg. 25
F
Audio Mode Display
墌
pg. 22
G
Tape Position Indicator
The tape position indicator
appears on the TV screen
when you press
3 or
5from the Stop mode
or perform an Index Search
(
墌
pg. 21). The position of
“
q” in relation to “0”
(beginning) or “+” (end)
shows you where you are
on the tape.
NOTE:
Depending on the type of tape being used, the tape position
indicator may not appear correctly.
H
Type of Broadcast
墌
pg. 26
I
Current Day/Month/Year
J
Clock Display
K
Channel Position Number and Station Name/
Auxiliary Input Indicator (L-1, L-2, F-1, S-1 or
SAT*)
*When “L-2 SELECT” is set to “SAT” (
墌
pg. 37), “SAT” appears
instead of “L-2”.
L
Timer Warning Display
A warning appears on the TV screen to tell you that the timer-
recording is to start in 5 minutes if you’re not in the Timer
mode at that time. The warning blinks for the entire 5
minutes leading up to the start of timer recording. To clear
the display, press
& on the remote control.
M
“Cassette Loaded” Mark
BeginningEnd
HRS7700EU1.fm Page 6 Wednesday, March 8, 2000 6:15 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
7
Filename [HRS7700EU1.fm]
Page 7March 8, 2000 1:13 pm
REMOTE CONTROL
A
TV Button
墌
“Operating JVC TVs” in the right
column
B
TV/VCR Button
墌
pg. 24 and “Operating JVC
TVs” in the right column
C
REVIEW Button
墌
pg. 20
D
NUMBER Keys
墌
pg. 23, 28
E
VPS/PDC Button
墌
pg. 29, 31
F
Cancel
&
Button
墌
pg. 32
0000 Button
墌
pg. 25
G
STOP +/– Button
墌
pg. 30
H
START +/– Button
墌
pg. 30
I
PROG Button
墌
pg. 28
J
Programme Check
"
Button
墌
pg. 32
K
Rewind
3
Button
墌
pg. 18, 20
L
Record
7
Button
墌
pg. 23
M
Stop
8
Button
墌
pg. 18, 23
N
MENU Button
墌
pg. 14
O
r
t
Button
墌
pg. 10
TV PR +/– Button
墌
“Operating JVC TVs” below
P
STANDBY/ON
1
Button
墌
pg. 10
Q
AUDIO Button
墌
pg. 22
^
(TV Muting) Button
墌
“Operating JVC TVs”
below
R
Display – – : – – Button
墌
pg. 25
S
DAILY Button
墌
pg. 29, 31
T
WEEKLY Button
墌
pg. 29, 31
U
AUX Button
墌
pg. 35
V
Timer
#
Button
墌
pg. 29, 31
W
DATE +/– Button
墌
pg. 30
X
PR +/– Button
墌
pg. 23
Y
Auto Tracking
p
Button
墌
pg. 21
SP/LP Button
墌
pg. 23
Z
30 SEC Button
墌
pg. 20
a
Play
4
Button
墌
pg. 18
b
Fast Forward
5
Button
墌
pg. 18, 20
c
Pause
9
Button
墌
pg. 19
d
OK Button
墌
pg. 11
e
w
e
Button
墌
pg. 19, 21
TV
%
+/– Button
墌
“Operating JVC TVs” below
Buttons with a small dot on the left side of the name can also
be used to operate your JVC TV while holding down the
TV
button. (
墌
“Operating JVC TVs” in the right column)
This remote control transmits A code signals only; it is not
applicable to B code signals.
How To Use
The remote control can operate most of your video recorder’s
functions, as well as basic functions of JVC TV sets.
(
墌
“Operating JVC TVs” below)
●Point the remote control toward the receiving window.
●The maximum operating distance of the remote control is
about 8 m.
Operating JVC TVs
To operate your TV, while holding down the
TV
button, press
the corresponding button:
1,
TV/VCR
,
TV PR
+/–,
TV
%
+/–
, ^(TV Muting).
NOTES:
●When inserting the batteries, be sure to insert in the correct
directions as indicated under the battery cover.
●Depending on the type of JVC TV, some or all functions
may not be operated using the remote control.
●If the remote control doesn’t work properly, remove its
batteries, wait a short time, replace the batteries and then
try again.
HRS7700EU1.fm Page 7 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
8
EN
Page 8March 9, 2000 3:43 pm
INSTALLING YOUR NEW RECORDER
Basic Connections
It’s essential that your video recorder be properly
connected.
A
Check the contents.
Make sure the package contains all of the accessories
listed in “SPECIFICATIONS” on page 66.
B
Situate the recorder.
Place the recorder on a stable, horizontal surface.
C
Connect the recorder to TV.
The connection method you use depends on the type of
TV you have.
RF Connection
8
To connect to a TV with NO AV input connectors . . .
A
Disconnect the TV aerial cable from the TV.
B
Connect the TV aerial cable to the ANT. IN connector
on the rear panel of the recorder.
C
Connect the provided RF cable between the RF OUT
connector on the rear panel of the recorder and the
TV’s aerial connector.
AV Connection
8
To connect to a TV with AV input connectors . . .
A
Connect the aerial, recorder and TV as per “RF
Connection”.
B
Connect an optional 21-pin SCART cable between the
AV1 (L-1) IN/OUT connector on the rear panel of the
recorder and the TV’s 21-pin SCART connector.
D
Connect the recorder to mains.
Plug the end of the mains power cord into a mains outlet.
Make AV connection if your TV has a 21-pin AV input
connector (SCART) in order to reduce the possibility of
interference. With AV connection, you can enjoy
stereo playback of video tapes if you are using a stereo
TV.
NOTES:
●The AV1 (L-1) IN/OUT connector accepts and delivers
either a composite signal (regular video signal) or a Y/C
signal (a signal in which the luminance and chrominance
signals are separated). If your TV’s 21-pin AV input
connector (SCART) is compatible with the Y/C signal, set
“L-1 OUTPUT” to “S-VIDEO” after the connection and the
initial settings are completed (
墌
pg. 36). You can obtain
high-quality S-VHS pictures. (For connection, be sure to
use a 21-pin SCART cable that is compatible with the Y/C
signal.)
●Set your TV to the VIDEO (or AV), Y/C, or RGB mode
according to the type of your TV’s SCART connector.
●For switching the TV’s mode, refer to the instruction
manual of your television.
●To obtain high-quality S-VHS pictures, you can also use the
S-VIDEO connection described on page 9.
Aerial connector
Back of TV
21-pin SCART
connector
TV aerial cable
RF cable
(provided)
21-pin SCART
cable
(not provided)
Mains power cord
Mains outlet
Back of recorder
AV1 (L-1) IN/OUT
ANT. IN
RF OUT
THESE STEPS MUST BE COMPLETED BEFORE ANY
VIDEO OPERATION CAN BE PERFORMED.
After the connection is completed, perform “Auto Set
Up” on page 10.
HRS7700EU1.fm Page 8 Thursday, March 9, 2000 3:43 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
9
Filename [HRS7700EU1.fm]
Page 9March 8, 2000 1:13 pm
S-VIDEO Connection
8To connect to a TV with S-VIDEO/AUDIO IN
connectors . . .
A
Connect the recorder to TV.
A
Connect the aerial, recorder and TV as per “RF
Connection” (
墌
pg. 8).
B
Connect the recorder’s S OUT connector to the TV’s
S-VIDEO IN connector.
C
Connect the recorder’s AUDIO OUT connectors to the
TV’s AUDIO IN connectors.
B
Connect the recorder to mains.
Plug the end of the mains power cord into a mains outlet.
NOTES:
●You can obtain high-quality S-VHS pictures.
●With S-VIDEO connection, you cannot use the Preset
Download function (
墌
pg. 12).
●If your TV is not stereo-capable, use the recorder’s AUDIO
OUT connectors to connect to an audio amplifier for Hi-Fi
stereo sound reproduction. (
墌
pg. 47)
●To operate the recorder with your TV using the S-VIDEO
connection, set your TV to its AV mode.
●For switching the TV’s mode, refer to the instruction manual of
your television.
Back of TV
Aerial connector
S-VIDEO IN
connector
AUDIO IN connectors
S-Video cable
(not provided)
Audio cable
(not provided)
Mains outlet
Mains power
cord
Back of recorder
RF cable (provided)
S OUT
AUDIO OUT
TV aerial cable
After the connection is completed, perform “Auto Set
Up” on page 10.
HRS7700EU1.fm Page 9 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
10
EN
Page 10March 8, 2000 1:13 pm
INITIAL SETTINGS
Auto Set Up
Auto Channel Set/Auto Clock Set/
Auto Guide Program Number Set
A
Turn on the recorder.
Press
1
on the recorder or remote control. The Country
Set display appears on the front display panel and/or on
the TV screen.
B
Select your country.
On the front display panel
Press
rt
to select your international telephone country
code of your country referring to the chart in the left
column.
(Example) DEUTSCHLAND (49) is selected.
NOTES:
●If you have selected BELGIUM (32) or SUISSE (41), go to
step
3
.
●If you have selected MAGYARORSZÁG (36),
C
ESKÁ
REPUBLIKA (42), POLSKA (48), РОССИЯ (07) or OTHER
EASTERN EUROPE (EE), press
OK
. The Clock Set screen
appears. Set the clock manually (
墌
pg. 60), then go to step
4
.
●If you have selected any other country name (code), press
OK
and go to step
4
.
After the
1 button on the recorder or remote control is
pressed for the first time to power on the recorder
, by simply
selecting your country*, the Auto Set Up function sets the
tuner channels, clock** and Guide Program numbers
automatically.
*If you live in Belgium (BELGIUM) or Switzerland (SUISSE), you also
need to select your language.
**If you live in Hungary (MAGYARORSZÁG), Czech Republic (
C
ESKÁ
REPUBLIKA), Poland (POLSKA), Russia (
РОССИЯ
) or other
countries in Eastern Europe (OTHER EASTERN EUROPE), set the
clock manually.
International Telephone Country Code
BELGIUM
C
ESKÁ REPUBLIKA
DANMARK
DEUTSCHLAND
ESPAÑA
GREECE
ITALIA
MAGYARORSZÁG
NEDERLAND
NORGE
:
:
:
:
:
:
:
:
:
:
32
42
45
49
34
30
39
36
31
47
ÖSTERREICH
POLSKA
PORTUGAL
SUISSE
SUOMI
SVERIGE
РОССИЯ
OTHER WESTERN EUROPE
OTHER EASTERN EUROPE
:
:
:
:
:
:
:
:
:
43
48
351
41
358
46
07
– –
EE
Before starting, make sure of the following:
●The TV aerial cable should be connected to the recorder.
●The recorder’s mains power cord should be connected to a
mains outlet.
●If you want to use the on-screen display, the TV should be
set to its AV mode (with AV or S-VIDEO connection
墌
pg. 8, 9) or UHF channel 36 (with RF connection
墌
pg. 8).
NOTE:
If you have connected your TV to
the recorder with RF connection
and the on-screen display
appearing on UHF channel 36
looks distorted, perform “Video
Channel Set” on page 58.
On the on-screen display
Press
rt
to move the
highlight bar (pointer) to your
country’s name.
HRS7700EU1.fm Page 10 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
11
Filename [HRS7700EU1.fm]
Page 11March 8, 2000 1:13 pm
C
Select the language.
Press
OK
. The Language Set display appears on the front
display panel and/or on the TV screen.
On the front display panel
Press
rt
to select your language code.
(Example) DEUTSCH (02) is selected for SUISSE (41).
D
Perform Auto Set Up.
Press
OK
. The AUTO SET/T-V LINK display appears on
the front display panel and/or on the TV screen.
On the front display panel
Press
rt
to select “Auto” and press
OK
or
e
.
●If you have connected the recorder to your TV via the AV
connection (
墌
pg.8), the recorder will automatically perform
Preset Download (
墌
pg. 12) instead of the Auto Set Up.
NOTES:
●In the area where no TV station transmits a PDC (Programme
Delivery Control) signal, the recorder can perform neither
Auto Clock Set nor Auto Guide Program Number Set.
●If there is a power cut, or if you press
1 or
MENU
while Auto
Set Up is in progress, Auto Set Up will be interrupted; be sure
to turn off the recorder power once and try again from step
1
.
●Auto Clock Set may not function properly depending on the
reception condition.
●If no sound accompanies the picture or the audio sounds
unnatural on some channels that have been stored by Auto Set
Up, the TV system setting for those channels may be incorrect.
Select the appropriate TV system for those channels
(
墌
pg. 55, “INFORMATION”).
Language Code
ENGLISH
DEUTSCH
FRANCAIS
ITALIANO
CASTELLANO
NEDERLANDS
SVENSKA
:
:
:
:
:
:
:
01
02
03
04
05
06
07
NORSK
SUOMI
DANSK
POLSKI
C
E
c
TINA
MAGYAR
ЯЗЫК
:
:
:
:
:
:
:
08
09
10
11
12
13
14
On the on-screen display
Press
rt
to move the
highlight bar (pointer) to the
language of your choice.
On the on-screen display
Press
rt
to move the
highlight bar (pointer) to
“AUTO SET” and press
OK
or
e
.
“Auto” blinks on the front display panel; do NOT press
any button on the recorder or remote control until the
front display panel shows clock time, “(CH) 1” or
“
– –:– –
” as illustrated on page 13.
International telephone
country code
Language code
●If you are using the on-screen
display, the AUTO SET
screen will appear. As Auto
Set Up progresses, the “
q”
mark on the TV screen
moves from left to right.
When the Auto Set Up is
completed, “SCAN
COMPLETED” appears for
about 5 seconds, then the
normal screen appears.
ATTENTION
Once you have performed Auto Set Up, even if the recorder’s
memory backup has expired, all the stored stations and their
Guide Program numbers remain in the recorder’s memory
and the recorder will not perform Auto Set Up again. You
only need to set the clock. (
墌
pg. 60)
If you have moved to a different area, perform each setting as
required.
●Video channel setting (for RF connection users)
墌
pg. 58
●Tuner setting
墌
pg. 52
●Clock setting
墌
pg. 60
If a new station starts broadcasting in your area, perform
tuner setting (
墌
pg. 52) and, if necessary, video channel
setting (
墌
pg. 58).
BeginningEnd
HRS7700EU1.fm Page 11 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
12
EN
Page 12March 8, 2000 1:13 pm
INITIAL SETTINGS (cont.)
Preset Download
Auto Channel Set by Downloading
from TV/Auto Clock Set/Auto Guide
Program Number Set
NOTES:
●For details, refer to the instruction manual of your TV.
●In the area where no TV station transmits a PDC (Programme
Delivery Control) signal, the recorder can perform neither
Auto Clock Set nor Auto Guide Program Number Set.
●If there is a power cut, or if you press
1 or
MENU
while
downloading or set up is in progress, it will be interrupted; be
sure to turn off the recorder power once and try again from the
beginning.
●Auto Clock Set may not function properly depending on the
reception condition.
●On this recorder, the characters available for station names
(ID) are A–Z, 0–9, –,
f, + and I (space). Some names of
downloaded stations may differ from those of your TV
(
墌
pg. 56).
If you have connected the recorder to your TV via the AV
connection (
墌
pg. 8), the recorder will automatically perform
Preset Download instead of the Auto Set Up in step
4
on page
11. After downloading, the recorder sets the clock and Guide
Program numbers automatically.
A
Perform Preset Download.
Press
OK
. The AUTO SET/T-V LINK display appears on
the front display panel and/or on the TV screen.
On the front display panel
Press
rt
to select “CH – –” and press
OK
or
e
.
B
Set the video channel.
Set the video channel to off manually. (
墌
pg. 58)
ATTENTION
You can use this function only with a TV offering T-V Link,
etc.* Be sure to use a fully-wired 21-pin SCART cable.
*Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-
wired 21-pin SCART cable. The degree of compatibility and
available functions may differ by system.
Perform steps
1
to
3
of “Auto Set Up” on page 10 before
continuing.
On the on-screen display
Press
rt
to move the
highlight bar (pointer) to
“T-V LINK” and press
OK
or
e
.
Preset positions on the front display panel increase from
“CH1”; do NOT press any button on the recorder or remote
control until the front display panel shows clock time,
“(CH) 1” or “– –:– –” as illustrated on page 13.
●If you are using the on-screen
display, the T-V LINK screen
will appear. Then the GUIDE
PROG SET screen will appear
during Guide Program
Number Set. When Preset
Download is completed,
“COMPLETED” appears for
about 5 seconds, then the
normal screen appears.
●If you press any button on the
recorder or remote control
while downloading is in
progress, it will be interrupted.
HRS7700EU1.fm Page 12 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-Full-NoTitle0
EN
13
Filename [HRS7700EU1.fm]
Page 13March 8, 2000 1:13 pm
Results of Auto Set Up/Preset Download appear on the front display panel
If both Auto Channel Set and Auto Clock Set have been performed successfully, the
correct current time is displayed.
Turn on the TV and select its video channel or AV mode, then make sure that all necessary stations
have been stored in the recorder’s memory by using the
PR
button(s).
●If station names (ID –
墌
pg.57) have also been stored in the recorder’s memory, the station name
will be displayed at the top left corner of the TV screen for about 5 seconds when the recorder is
tuned to a different station.
●If you want to set the tuner manually such as to add or skip channels, to change channel
positions, or to set or change station names, see pages 54 – 57.
If Auto Channel Set has succeeded but Auto Clock Set has not, “1” (channel position) is
displayed.
A
Turn on the TV and select its video channel or AV mode, then make sure that all necessary
stations have been stored in the recorder’s memory by using the
PR
button(s).
●If station names (ID –
墌
pg.57) have also been stored in the recorder’s memory, the station name
will be displayed at the top left corner of the TV screen for about 5 seconds when the recorder is
tuned to a different station.
●If you want to set the tuner manually such as to add or skip channels, to change channel
positions, or to set or change station names, see pages 54 – 57.
B
Perform “Clock Set” on page 60.
If both Auto Channel Set and Auto Clock Set have failed, “– –:– –” is displayed.
Make sure the cables are connected properly and turn off the recorder’s power once, then turn the
recorder’s power back on again.
The Country Set display appears on the front display panel and/or on the TV screen; perform “Auto
Set Up” on page 10 or “Preset Download” on page 12 again.
IMPORTANT
●To check if the Guide Program numbers have been set correctly, perform the S
HOW
V
IEW
Timer Programming (
墌
pg. 28).
●In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work
properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the S
HOW
V
IEW
system, the recorder will record a TV programme of a different station. When programming the timer using the S
HOW
V
IEW
system, be sure to check the desired channel is selected correctly (
墌
pg. 28, “S
HOW
V
IEW
®
Timer Programming”).
●Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with
an unacceptable picture (
墌
pg. 55, “Delete A Channel”).
INFORMATION
Language for the on-screen display
Auto Set Up also selects the language automatically for the on-screen display depending on the Country setting you have made in
step
2
on page 10 (unless you have selected BELGIUM or SUISSE), as shown below.
If you want to change the language setting manually, see “Language” on page 14.
Just Clock
Your recorder is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at
regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to “ON”
(
墌
pg. 60, “Just Clock”).
SUOMI
]
SUOMIDANMARK
]
DANSKNEDERLAND
]
NEDERLANDS
PORTUGAL
]
ENGLISHÖSTERREICH
]
DEUTSCHGREECE
]
ENGLISH
DEUTSCHLAND
]
DEUTSCH
C
ESKÁ REPUBLIKA
]
C
E
c
TINAРОССИЯ
]
ЯЗЫК
POLSKA
]
POLSKIITALIA
]
ITALIANOOTHER WESTERN EUROPE
]
ENGLISH
NORGE
]
NORSKMAGYARORSZÁG
]
MAGYAROTHER EASTERN EUROPE
]
ENGLISH
SVERIGE
]
SVENSKAESPAÑA
]
CASTELLANO
HRS7700EU1.fm Page 13 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
14
EN
Page 14March 8, 2000 1:13 pm
INITIAL SETTINGS (cont.)
Language
This recorder offers you the choice to view on-screen
messages in 14 different languages. Though Auto Set Up
selects the language automatically (
墌
pg. 13), you can
change the language setting manually as required.
A
Access the Main Menu screen.
Press
MENU
.
B
Access the Country Set screen.
C
Select your country.
Press
rt
to move the highlight bar (pointer) to your
country’s name, then press
OK
or
e
.
D
Select the language.
E
Return to the normal screen.
Press
MENU
.
Turn on the TV and select the video channel (or
AV mode).
Press
rt
to move the
highlight bar (pointer) to
“AUTO CH SET”, then press
OK
or
e
.
Press
rt
to move the
highlight bar (pointer) to the
language of your choice.
●You do not have to press
OK
;
pressing
OK
enters AUTO SET/
T-V LINK screen.
HRS7700EU1.fm Page 14 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right
EN
15
Filename [HRS7700EU1.fm]
Page 15March 8, 2000 1:13 pm
SAT CONTROL SET
Satellite Receiver
Control Setting
The following procedure is required if you receive
satellite channels through a satellite receiver.
Approximately 20 seconds before the S
HOW
V
IEW
timer
programming (
墌
pg. 28) or Express timer programming
(
墌
pg.30) starts, the recorder sets its input mode to “L-2”
and automatically switches the satellite receiver’s
channels using the provided Satellite Controller.
Installing Satellite Controller
A
Situate the Satellite Controller.
Place the Satellite Controller so that the path between its
transmitter and the satellite receiver’s remote sensor is
unobstructed.
B
Attach the Satellite Controller.
Fix securely using the adhesive strip attached on the back
of the Satellite Controller.
C
Make connections.
Be sure to connect the recorder’s AV2 (L-2) IN/DECODER
connector to the satellite receiver’s 21-pin SCART
connector.
NOTE:
When connecting your satellite receiver, refer to its instruction
manual.
D
Connect the Satellite Controller to recorder.
Connect the Satellite Controller to the SAT CTL connector
on the rear panel.
Satellite receiver
Satellite Controller
(suggested locations)
Transmitter
21-pin SCART
cable
(not provided)
SAT CTL
AV2 (L-2) IN/DECODER
Your recorder
Satellite Controller
Back of recorder
Satellite receiver
HRS7700EU1.fm Page 15 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
16
EN
Page 16March 8, 2000 1:13 pm
SAT CONTROL SET (cont.)
Setting satellite receiver's brand and
channel
After installation, set the satellite receiver’s brand and
channel correctly; otherwise, the Satellite Controller
cannot work correctly.
A
Turn on the satellite receiver.
Turn on the satellite receiver’s power.
B
Access the Main Menu screen on the
recorder.
Press
MENU
.
C
Access the Initial Set screen.
Press
rt
to move the highlight bar (pointer) to “INITIAL
SET”, then press
OK
or
e
.
D
Access the Sat Control Set screen.
E
Enter the satellite receiver’s brand.
F
Select the satellite receiver’s channel for
testing.
Turn on the TV and select the video channel (or AV
mode).
Press
rt
to move the
highlight bar (pointer) to
“SAT CONTROL SET”, then
press
OK
or
e
.
Press the appropriate
NUMBER
keys to enter the
brand code from the list on
page 17, then press
OK
.
●If the brand code you entered
is invalid, the code field will
be reset. Enter the correct
brand code again.
●If the recorder is in playback or
recording mode, you cannot
set the brand code.
Press the appropriate
NUMBER
keys to enter one
of the channel positions on
the satellite receiver, then
press
OK
.
●You can select the channel
position between 1 to 999.
●After pressing
OK
, the recorder
enters the Test mode.
HRS7700EU1.fm Page 16 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-2lineTitle0
EN
17
Filename [HRS7700EU1.fm]
Page 17March 8, 2000 1:13 pm
SAT CONTROL SET (cont.)
T-V LINK
G
Check the result of the test.
If the satellite receiver’s
channel number has been
changed to the same one as
you set in step 6 ...
Press
rt
to move the highlight
bar (pointer) to “CHANGED
TO ...”, then press
OK
or
e
to
finish the Sat Control Set mode.
If the satellite receiver’s
channel number has not been changed correctly ...
Press
rt
to move the highlight bar (pointer) to “NOT
CHANGED”, then press
OK
or
e
. Then perform the
procedure again from step
5
.
NOTES:
●The Satellite Controller may not work with all types of satellite
receiver.
●For some satellite receivers, you need to set its channel input
mode to 2-digit.
●If your satellite receiver has more than two channel modes, be
sure to set to “All Channel Mode”. For details, refer to the
instruction manual of the satellite receiver.
●When selecting the satellite receiver’s channel (
墌
step
6
),
signals from the remote control may interfere with signals
transmitted from the Satellite Controller. In this case, move the
remote control as close to the recorder’s infrared beam
receiving window as possible.
T-V Link Functions
When you connect the recorder to your TV via a fully-wired
21-pin SCART cable (
墌
pg. 8), the following functions are
available. You can use these functions only with a TV offering
T-V Link, etc.*
For details, refer to the instruction manual of your TV.
*Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired
21-pin SCART cable. The degree of compatibility and available
functions may differ by system.
NexTView Link
You can download the EPG (Electronic Programme Guide)
information from your TV for timer-programming on the
recorder.
For details, refer to the instruction manual of your TV.
TV Auto Power On
The TV will turn on and be set to its AV mode automatically
whenever you play a tape.
For details, refer to the instruction manual of your TV.
VCR Auto Standby
You can use your TV’s remote control to turn off the recorder.
For details, refer to the instruction manual of your TV.
Direct Rec
You can easily start recording the programme that you are
watching on your TV. When you use this function, set “DIRECT
REC” to “ON” (
墌
pg. 49).
BRAND NAMECODE
JVC
AMSTRAD
CANAL SATELLITE
CANAL +
D-BOX
ECHOSTAR
ECHOSTAR (VIA DIGITAL)
FINLUX
FORCE
GALAXIS
GRUNDIG
HIRSCHMANN
ITT NOKIA
JERROLD
KATHREIN
LUXOR
MASCOM
MASPRO
NOKIA
PACE
PANASONIC
PHILIPS
RFT
SAGEM
SALORA
SIEMENS
SKYMASTER
TPS
TRIAX
WISI
73
60, 61, 62, 63, 92
81
81
85
78, 79, 80
82
68
89
88
64, 65
64, 78
68
75
70, 71
68
93
70
87
65, 67, 74, 86, 92
74
66, 84
69
83
68
64
69
83
91
64
HRS7700EU1.fm Page 17 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
18
EN
Page 18March 8, 2000 1:13 pm
PLAYBACK
Basic Playback
A
Load a cassette.
Make sure the window side is up, the rear label side is
facing you and the arrow on the front of the cassette is
pointed toward the recorder.
●Don’t apply too much pressure when inserting.
●The recorder’s power comes on automatically and the counter
is reset to “0:00:00”.
●If the record safety tab has been removed, playback begins
automatically.
B
Find the programme start point.
If the tape is advanced past the start point, press
3
or
turn the
SHUTTLE
ring to the left. To go forward, press
5
or turn the
SHUTTLE
ring to the right.
C
Start playback.
Press
4
. “BEST” appears blinking in the recorder’s front
display panel during automatic tracking. (
墌
pg. 27)
D
Stop playback.
Press
8
on the remote control or
0
on the recorder’s
front panel. Then press
0
to remove the cassette.
Turn on the TV and select the video channel (or
AV mode).
Clean the video heads using a dry cleaning
cassette — TCL-2UX — when:
●Rough, poor picture appears while a tape is played back.
●The picture is unclear or no picture appears.
●“USE CLEANING CASSETTE” appears on the screen (only
with “O.S.D.” set to “ON” (
墌
pg. 49)).
Usable cassettes
●Compact VHS camcorder recordings can be played on this
video recorder. Simply place the recorded cassette into a
VHS Cassette Adapter and it can be used just like any full-
sized VHS cassette.
●This video recorder can record on regular VHS and Super
VHS cassettes. While only VHS signals can be recorded on
regular VHS cassettes*, both VHS and Super VHS signals
can be recorded and played back using Super VHS
cassettes.
*By using the S-VHS ET function, it is possible to record and
play back with S-VHS picture quality on VHS cassettes
with this recorder.
HRS7700EU1.fm Page 18 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
19
Filename [HRS7700EU1.fm]
Page 19March 8, 2000 1:13 pm
Playback Features
NOTE:
Refer to the
SHUTTLE
ring
illustration on the
right as you read
the following
procedures.
Still Picture/Frame-By-Frame
Playback
1
Pause during playback.
Press
9
.
●If there is vertical jitter, use the
PR
buttons to correct the
picture.
2
Activate frame-by-frame playback.
Turn the
JOG
dial to the right for forward frame-by-frame
playback, or to the left for reverse frame-by-frame
playback.
OR
Press
9
.
OR
Press
w
or
e
.
Slow Motion
During playback or still, turn the
SHUTTLE
ring to the
right for forward slow motion, or to the left for reverse
slow motion (refer to the illustration on the left).
OR
During still picture, press and hold
9
for 2 seconds, then
release. Press and release again to return to still picture.
OR
During still picture, press and hold
w
or
e
. Release to
return to still picture.
Variable Speed Search
During playback or still, turn the
SHUTTLE
ring to the
right for forward variable-speed search, or to the left for
reverse variable-speed search (refer to the illustration on
the left).
OR
During playback, press
w
or
e
.
●The more times you press, the faster the playback picture
moves.
●To decrease speed, press the button for the opposite direction.
ATTENTION
●Picture may not appear during high-speed search with an
LP-recorded tape.
●In the high-speed search, still, slow motion or frame-by-
frame playback mode, the picture will be distorted, and
there will be a loss of colour.
●When normal playback resumes from search, still, slow
motion or frame-by-frame playback, the picture may jitter
vertically momentarily depending on the type of TV being
used.
To resume normal playback, press
4
.
HRS7700EU1.fm Page 19 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
20
EN
Page 20March 8, 2000 1:13 pm
PLAYBACK (cont.)
Skip Search
During playback, press
30 SEC
1 to 4 times to skip over
unwanted sections.
Each press initiates a 30-second period of fast-motion
playback. Normal playback resumes automatically.
High-Speed (Turbo) Search
During playback or still, turn the
SHUTTLE
ring all the
way to the right for forward high-speed search, or to the
left for reverse high-speed search. Releasing
SHUTTLE
ring resumes still picture playback.
●For forward high-speed search, turn the
SHUTTLE
ring all the
way to the right and release it within 1 second.
●For reverse high-speed search, turn the
SHUTTLE
ring all the
way to the left and release it within 1 second.
OR
During playback or still, press
5
for forward high-
speed search, or
3
for reverse high-speed search.
NOTE:
For short searches, press and hold 5 or 3 for over 2
seconds during playback or still picture. When released, normal
playback resumes.
Instant ReView
Simply by pressing a single button, the recorder power comes
on, rewinds, and begins playback of the last timer-recorded
programme. If you have several programmes recorded, you can
easily access any of them.
NOTE:
Before starting, make sure that the recorder is off and that the
Timer mode is disengaged.
Activate Instant ReView.
Press
REVIEW
. The recorder power comes on and the
recorder searches for the index code indicating the start
of the last timer-recorded programme. Once it’s found,
playback begins automatically.
●The front display panel tells you how many programmes have
been timer-recorded. If you have, for example, 3 programmes,
“REVIEW” and “3” appear and blink. To watch the first of the 3
programmes, press
REVIEW
three times
. The recorder searches
and begins playback automatically. You can access a
programme as far as 9 index codes away from the current tape
position.
●Instant ReView is not possible while the recorder is in the
Timer mode.
●The number of recorded programmes will not be displayed on
the front display panel after Automatic Satellite Programme
Recording (
墌
pg. 34).
To resume normal playback during a Skip Search,
press
4
.
To resume normal playback, press
4
.
HRS7700EU1.fm Page 20 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
21
Filename [HRS7700EU1.fm]
Page 21March 8, 2000 1:13 pm
Index Search
Your recorder automatically marks
index codes at the beginning of
each recording. This function gives
you quick access to any one of 9
index codes in either direction.
NOTE:
Before starting, make sure the
recorder is in the Stop mode.
Activate Index Search.
Press
w
or
e
(
2
or
6
). “
2
1” or “
6
1” is
displayed on the TV screen and search begins in the
corresponding direction.
●To access index codes 2 through 9, press
w or e repeatedly
until the correct index number is displayed.
Example:
To locate the beginning of B from the current position, press
w
twice.
To locate the beginning of D from the current position, press
e
once.
●When the specified index code is located, playback begins
automatically.
Next Function Memory
The Next Function Memory “tells” the recorder what to do after
rewinding. Before continuing, make sure the recorder is in the
Stop mode.
a-
For Automatic Start Of Playback
Press
3
, then press
4
within 2 seconds.
b-
For Automatic Power Off
Press
3
, then press
1
within 2 seconds.
c-
For Automatic Timer Standby
Press
3
, then press
#
(
TIMER
) within 2 seconds.
Manual Tracking
Your recorder is equipped with automatic tracking control.
During playback, you can override this and adjust the tracking
manually by pressing the
PR
buttons.
1
Override automatic tracking.
Press
p
on the remote control.
2
Adjust the tracking manually.
Press
PR
+
or
–
.
3
Return to automatic tracking.
Press
p
on the remote control.
NOTE:
When a new tape is inserted, the recorder enters the automatic
tracking mode automatically.
Digital TBC/NR
Your recorder is equipped with the Digital TBC (Time Base
Corrector) that removes jitter from fluctuating video signals to
deliver a stable picture even with old tapes and rental cassettes.
The on/off of Digital 3-DNR (Noise Reduction) which cuts noise
and enables clear picture reproduction is also linked to this
function.
* The default setting is on.
We recommend that you use Digital TBC/NR when...
... playing back a tape recorded on a camcorder.
... playing back a tape repeatedly used.
... using this video recorder as the source player for editing.
Activate Digital TBC/NR.
Press
DIGITAL TBC/NR
so that the button lights up.
●To turn off Digital TBC/NR, press
DIGITAL TBC/NR
again so
that the light goes off.
NOTES:
●If you play back a tape recorded under poor TV reception
condition, the picture may become more stable with Digital
TBC/NR set to off.
●When Digital TBC/NR is set to on, if you play back a tape
where certain types of signals are recorded (using a PC or
some character generators), the playback picture may be
distorted. If this is the case, turn off Digital TBC/NR.
●When playing back a MESECAM tape, Digital TBC/NR does
not function even though the DIGITAL TBC/NR button is lit.
Current position
Index number
HRS7700EU1.fm Page 21 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
22
EN
Page 22March 8, 2000 1:13 pm
PLAYBACK (cont.)
Repeat Playback
Your recorder can automatically play back the whole tape 100
times repeatedly.
1
Start playback.
Press
4
.
2
Activate Repeat Playback.
Press
4
and hold for over 5 seconds, then release.
●The Play indicator (
u) on the front display panel blinks
slowly.
●After playing back a tape 100 times, the recorder stops
automatically.
3
Stop Repeat Playback.
Press
8
at any time.
●Pressing
4, 3, 5 or 9 also stops Repeat Playback.
Soundtrack Selection
Your recorder is capable of recording three soundtracks (HI-FI L,
HI-FI R and NORM) and will play back the one you select.
During Playback
Pressing
AUDIO
on the remote control changes the soundtrack
as follows:
NOTES:
●“
a + s” should normally be selected. In this mode, Hi-Fi
stereo tapes are played back in stereo, and the normal audio
track is played back automatically for tapes with only normal
audio.
●For instructions on recording stereo and bilingual
programmes, refer to page 26.
●“O.S.D.” must be set to “ON” or the on-screen displays will
not appear (
墌
pg. 49).
TRACK
USE
Recorder’s Front
Display Panel
On-Screen
Display
a
+
s
HI FI
L
j
h
R
For Hi-Fi stereo
tapes
a
HI FI
L
j
For main audio of
Bilingual tapes
s
HI FI
h
R
For sub audio of
Bilingual tapes
NORMNORM
For audio-dubbed
tapes
a
+
s
+ NORM
HI FI
NORM
For audio-dubbed
tapes
HRS7700EU1.fm Page 22 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right
EN
23
Filename [HRS7700EU1.fm]
Page 23March 8, 2000 1:13 pm
RECORDING
Basic Recording
A
Load a cassette.
Insert a cassette with the record safety tab intact.
●The recorder’s power comes on automatically and the counter
is reset to “0:00:00”.
B
Choose a programme.
Press
PR +/–
or the
NUMBER
keys to select the channel
you wish to record.
C
Set the tape speed.
Press
SP/LP
(
p
). Check the SP/LP indicator on the
recorder’s front display panel to confirm the selected tape
speed.
D
Start recording.
Press and hold
7
and press
4
on the remote control, or
press
7
on the recorder.
E
Pause/Resume recording.
Press
9
. Press
4
to resume recording.
F
Stop recording.
Press
8
on the remote control or
0
on the recorder.
Then press
0
to remove the cassette.
Turn on the TV and select the video channel (or
AV mode).
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording (
墌
pg.24) or timer recording (
墌
pg.28, 30), the
recording will resume automatically when power is restored
to the recorder unless the recorder’s memory backup has
expired.
B.E.S.T. takes place at the beginning of both the first SP and
the first LP recording after inserting the cassette. (
墌
pg. 27)
If “DIRECT REC” is set to “ON”, the programme that appears
on the TV screen will be recorded (
墌
pg. 49).
Accidental erasure prevention
To prevent accidental recording on a recorded cassette,
remove its safety tab. To record on it later, cover the hole
with adhesive tape.
Record safety tab
HRS7700EU1.fm Page 23 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
24
EN
Page 24March 8, 2000 1:13 pm
RECORDING (cont.)
Recording Features
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the recorder off
after recording is finished.
1
Start recording.
Press
7
on the recorder.
2
Engage the ITR mode.
Press
7
again. “
o
” blinks and “0:30” appears on the front
display panel.
3
Set the recording duration.
If you want to record for more than 30 minutes, press
7
to extend the time. Each press extends recording time by
30 minutes.
NOTE:
You can only perform ITR using the 7 button on the recorder’s
front panel.
Record One Programme While
Watching Another
If your recorder is connected to the TV via the AV
connection, press
TV/VCR
. The recorder’s VCR indicator
and the TV broadcast being recorded disappear. Once
recording is in progress, all you need to do is to set the
channel controls on the TV for the station you wish to
view.
●The programme selected with the TV’s channel controls
appears on the TV screen, while the one selected with the
recorder’s
PR
buttons is recorded on the tape.
●If a decoder is connected to the recorder (
墌
pg. 46), you can
select a scrambled channel as well with the TV channel
controls.
HRS7700EU1.fm Page 24 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
25
Filename [HRS7700EU1.fm]
Page 25March 8, 2000 6:16 pm
Elapsed Recording Time Indication
1
Set the counter display.
Press
– –:– –
until a counter reading appears on the front
display panel.
2
Reset the counter.
Press
0000
before starting recording or playback.
●The counter is reset to “0:00:00” and shows the exact elapsed
time as the tape runs. You can check the exact time of a
recording or playback.
Tape Remaining Time
Press
– –:– –
until the time remaining on the tape appears.
●The front display panel shows the tape remaining time with
“
y” displayed.
●By pressing the
– –:– –
button, you can change the display to
show the counter reading, channel position*, clock time or
tape remaining time.
*Channel position is not displayed during playback.
NOTE:
Depending on the type of tape being used, the tape remaining
time reading may not appear right away, or is not correct.
“– –:– –” may sometimes appear, or the display may blink on
occasion.
Super VHS ET (S-VHS ET)
— Recording on VHS cassettes with
S-VHS quality
You can record in SP mode on VHS cassettes with S-VHS picture
quality. Tapes recorded using this function can be played back
on a recorder equipped with the S-VHS ET function.
●You can activate the S-VHS ET function only before you start
recording on a VHS cassette.
●Before recording, make sure that “B.E.S.T.” is set to “ON”.
(
墌
pg. 49)
Engage the S-VHS ET mode.
Press
S-VHS ET
on the recorder. The button lights up.
●The S-VHS indicator lights up on the front display panel.
●To disengage the S-VHS ET mode, press
S-VHS ET
. The button’s
light goes off.
NOTES:
●
You cannot activate the S-VHS ET function ...
... while recording is in progress.
... while timer-recording or Instant Timer Recording
(
墌
pg. 24) is in progress.
... while B.E.S.T. (
墌
pg. 27) is in progress.
●
The S-VHS ET function does not work ...
... with S-VHS cassettes.
... with recordings in LP mode.
●
To keep the highest quality recording and playback pictures
over a long period of time, S-VHS recording on S-VHS
cassettes is recommended.
●
Use of high grade tapes is recommended for S-VHS ET
recordings. On some tapes, picture quality will not improve
even if the S-VHS ET function is used. Check the recording
quality before you start important recordings.
●
You can play back a tape recorded using the S-VHS ET
function on most of S-VHS recorders and of VHS recorders
equipped with SQPB (S-VHS QUASI PLAYBACK) function.
(Notice some recorders are not compatible with the S-VHS ET
function.)
●
While playing back a tape recorded using the S-VHS ET
function on some recorders, noise may appear. (If playback
picture becomes blurred or interrupted, use a cleaning
cassette.)
●
In the high-speed search, still, slow-motion or frame-by-frame
playback modes (
墌
pg. 19,
20), noise may appear. If these
modes are performed frequently on a tape recorded using the
S-VHS ET function, the tape may be damaged and the picture
may be deteriorated.
HRS7700EU1.fm Page 25 Wednesday, March 8, 2000 6:16 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU1.fm]
Masterpage:Left
26
EN
Page 26March 8, 2000 1:13 pm
RECORDING (cont.)
Retake
You can cut out unnecessary parts of a TV programme while you
are recording it.
1
Engage the Record-Pause mode.
Press
9
during recording.
2
Locate the start point.
Turn the
JOG
dial to the left or right (or hold down
3
or
5
) and release it when you reach the point where
you want to resume recording.
●Your recorder returns to the Record-Pause mode.
3
Resume recording.
Press
4
when you wish to resume recording.
NOTE:
Retake function does not work during Direct Rec (
墌
pg.17, 49).
Receiving Stereo and Bilingual
Programmes
Your recorder is equipped with a Sound-Multiplex decoder (A2)
and a Digital stereo sound decoder (NICAM) making reception
of stereo and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
●To listen to a stereo programme, press
AUDIO
until “
a” and
“
s” appear on the front display panel or “HIFI L jhR”
appears on the TV screen.
●To listen to a bilingual programme, press
AUDIO
until “
a” or
“
s” appears on the front display panel, or “HIFI L j” or
“HIFI
hR” appears on the TV screen (as required).
●To listen to the standard (Regular Monaural) audio while
receiving a NICAM broadcast, press
AUDIO
until “NORM”
appears on the front display panel or the TV screen.
NOTE:
“O.S.D.” must be set to “ON” or the on-screen displays will not
appear (
墌
pg. 49).
To Record Stereo and Bilingual Programmes (A2)
Stereo programmes are automatically recorded in stereo on the
Hi-Fi audio track (with the normal audio track recording mixed L
and R channel sound).
●Bilingual programmes are automatically recorded in bilingual
on the Hi-Fi audio track. The main soundtrack will be
recorded on the normal audio track.
To Record NICAM Stereo and Bilingual
Programmes
The NICAM audio programme will be recorded on the Hi-Fi
audio track, and the standard audio programme will be recorded
on the normal audio track.
NOTES:
●If the quality of stereo sound being received is poor, the
broadcast will be received in monaural with better quality.
●Before playing back a programme recorded in stereo, or a
bilingual programme, refer to “Soundtrack Selection” on page
22.
End of programmeBeginning of programme
Recorded part
Go back to end of programme to cut out
unnecessary part
ProgrammeProgramme
Unnecessary
part
Unnecessary
part
Type of Broadcast Being
Received
On-screen Display
A2 Stereo
A2 Bilingual
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
ST
BIL.
(none)
ST NICAM
BIL. NICAM
NICAM
HRS7700EU1.fm Page 26 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
27
Filename [HRS7700EU1.fm]
Page 27March 8, 2000 1:13 pm
B.E.S.T. Picture
System
The B.E.S.T. (Biconditional Equalised Signal Tracking)
system checks the condition of the tape in use during
playback and recording, and compensates to provide the
highest-possible playback and recording pictures. You
can set “B.E.S.T.” to “ON” or “OFF” to your preference
(
墌
pg. 49).
Playback
The recorder assesses the quality of the tape once you
initiate playback.
●The recorder adjusts the playback picture quality based on the
quality of the tape in use.
●B.E.S.T. is active during automatic tracking. “BEST” appears
blinking on the recorder’s front display panel.
NOTES:
●When watching a tape recorded with “B.E.S.T.” set to “ON”, it
is recommended that you leave B.E.S.T. on during playback as
well.
●When watching a rental tape or one recorded on another
video recorder, or when using this recorder as the player for
editing, set B.E.S.T. to your preference (
墌
pg. 49).
●“BEST” only appears at the beginning of automatic tracking.
Even though it doesn’t appear after that, the B.E.S.T. function is
operative.
Recording
The recorder assesses the quality of the tape once you
initiate recording.
DURING B.E.S.T.
●The recorder spends approximately 7 seconds assessing the
condition of the tape, then begins recording.
NOTES:
●The B.E.S.T. system works for both SP and LP modes only after
a tape has been inserted and the Record mode is first initiated.
It does not work during recording.
●The B.E.S.T. system does not work while Automatic Satellite
Programme Recording is in progress (
墌
pg. 34).
●In the case of timer recordings, the B.E.S.T. system works
before recording is initiated.
●Once the cassette is ejected, the B.E.S.T. data is cancelled. The
next time the cassette is used for recording, B.E.S.T. is re-
performed.
●Pressing the recorder’s
7 button while “BEST” is displayed
does not start Instant Timer Recording (
墌
pg. 24).
ATTENTION
Since the B.E.S.T. system works before recording actually
starts, there is a delay of approximately 7 seconds after
7
and
4 on the remote control are pressed, or 7 on the
recorder is pressed. To make sure you record the desired
scene or programme in its entirety, first perform the following
steps:
A
Press and hold
9 and press 7 to engage the Record
Pause mode.
●The recorder then automatically checks the condition of
the tape and, after approximately 7 seconds, re-enters
Record Pause mode.
B
Press
4 to start recording.
If you want to bypass the B.E.S.T. system and begin recording
immediately, set “B.E.S.T.” to “OFF” (
墌
pg. 49).
B.E.S.T. COMPLETE
HRS7700EU1.fm Page 27 Wednesday, March 8, 2000 1:14 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
28
EN
Page 28March 9, 2000 11:04 am
TIMER RECORDING
S
HOW
V
IEW
®
Timer
Programming
With the S
HOW
V
IEW
system, timer programming is greatly
simplified because each TV programme has a corresponding
code number which your recorder is able to recognize.
A
Access the S
HOW
V
IEW
screen.
The front display panel looks like this:
B
Enter the S
HOW
V
IEW
number.
The S
HOW
V
IEW
number you enter appears on the front display
panel with only a 4-digit number:
C
Access the S
HOW
V
IEW
Program screen.
The front display panel shows the programme start time. Pressing
"changes the display to the programme stop time, then the
date and channel position.
●If the number you entered is invalid, “ERROR” appears on the
TV screen and “Err” appears on the front display panel. Press
& and input a valid S
HOW
V
IEW
number.
●If the “GUIDE PROG SET” screen appears, see “ATTENTION”
on page 29.
Before performing the S
HOW
V
IEW
Timer
Programming:
●Make sure that the recorder’s built-in clock is set properly.
●Insert a cassette with the safety tab in place. The recorder
will come on automatically.
●Turn on the TV and select the video channel (or AV mode).
Press
PROG
.
Press the
NUMBER
keys to
enter the S
HOW
V
IEW
number
of a programme you wish to
record.
●If you make a mistake, press
&
and input the correct number.
Press
OK
, then the
S
HOW
V
IEW
Program screen
appears (if you’re just starting
out, “P1” appears).
IMPORTANT
Make sure the channel position number you wish to record is
displayed; if not, see “S
HOW
V
IEW
®
Setup” on page 59 and set
the Guide Program number correctly.
HRS7700EU2.fm Page 28 Thursday, March 9, 2000 11:04 AM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
29
Filename [HRS7700EU2.fm]
Page 29March 8, 2000 1:33 pm
D
Set the tape speed.
Press
SP/LP
(
p
).
E
Set the VPS/PDC mode.
Press
VPS/PDC
to select “ON” or “OFF”.
●If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC”
is lit on the front display panel, VPS/PDC is set to ON.
●If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC”
is not lit on the front display panel, VPS/PDC is set to OFF.
墌
“VPS/PDC Recording” on page 31.
F
Return to the normal screen.
Press
PROG
or
OK
. “PROGRAM COMPLETED” appears
on the TV screen for about 5 seconds, then the normal
screen appears. If “PROGRAM OVERLAPPED” appears
on the TV screen and “Err” on the front display panel, see
page 33.
●Repeat steps
1
–
6
for each additional programme.
G
Engage the recorder’s timer mode.
Press
#
(
TIMER
). The recorder turns off automatically
and “
#
” appears on the front display panel.
●To disengage the timer mode, press
# (
TIMER
) again.
NOTES:
●To Change The Stop Time . . .
. . . press
STOP
+/–
after pressing
OK
in step
3
. You can
compensate for anticipated programme schedule delays.
●To Timer-Record Weekly Or Daily Serials . . .
. . . after pressing
OK
in step
3
, press
WEEKLY
(
NUMBER
key
“
9
”) for weekly serials or
DAILY
(
NUMBER
key “
8
”) for daily
serials (Monday — Friday). Either “WEEKLY” or “DAILY”
appears on the TV screen. Pressing the button again makes the
corresponding indication disappear.
●You can programme this recorder to timer-record as many as 8
programmes. If you try to programme the recorder to record a
ninth, “PROGRAM FULL” appears on the TV screen and
“FULL” appears on the front display panel. To record the extra
programme, you must first cancel any unnecessary
programmes (
墌
pg. 32).
●It is not possible to timer-record a TV programme with a
S
HOW
V
IEW
number which starts with “0”.
Satellite Receiver Users
To timer-record a satellite broadcast using the S
HOW
V
IEW
system:
APerform “Satellite Receiver Control Setting” on page 15.
BPerform steps
1
–
7
. In step
3
, the front display panel
shows “L2” for the channel position. In step
5
, you cannot
set “VPS/PDC” to “ON”.
CLeave the satellite receiver’s power on.
ATTENTION
Guide Program Number Set
“GUIDE PROG SET” appears after performing step
3
if the
Guide Program number for the S
HOW
V
IEW
number you
entered has not been set.
If you want to set the Guide Program number for the satellite
broadcast station, press the
NUMBER
key “
0
” to change “TV
PROG” to “SAT”. Press
rt to input the channel position
number on which your recorder or satellite receiver receives
that station, then press
OK
or
e to set the Guide Program
number. The S
HOW
V
IEW
Program screen appears.
(Example)
To timer-record a ZDF
programme with the
S
HOW
V
IEW
system.
* If your recorder receives ZDF on
the channel position 2, press
OK
or
e
after entering “2”.
HRS7700EU2.fm Page 29 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
30
EN
Page 30March 9, 2000 11:04 am
TIMER RECORDING (cont.)
Express Timer
Programming
If you don’t know the S
HOW
V
IEW
number for the programme you
wish to record, use the following procedure to set your recorder
to timer-record the programme.
A
Access the S
HOW
V
IEW
screen.
Press
PROG
.
B
Access the Programme screen.
The front display panel looks like this:
C
Enter the programme start time.
The front display panel looks like this:
D
Enter the programme stop time.
Press
STOP+/–
to enter the time you want recording to
stop.
●Press and hold
STOP+/–
to move in 30-minute increments, or
press and release repeatedly to move 1 minute at a time.
E
Enter the programme date.
Press
DATE+/–
.
●The current date appears on the TV screen. The date you enter
appears in its place.
Before performing Express Timer Programming:
●Make sure that the recorder’s built-in clock is set properly.
●Insert a cassette with the safety tab in place. The recorder
will come on automatically.
●Turn on the TV and select the video channel (or AV mode).
Press
START+/–
. (If you’re
just starting out, “P1”
appears.)
Press
START+/–
to enter the
time you want recording to
start.
●Press and hold
START+/–
to
move in 30-minute
increments, or press and
release repeatedly to move 1
minute at a time.
HRS7700EU2.fm Page 30 Thursday, March 9, 2000 11:05 AM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
31
Filename [HRS7700EU2.fm]
Page 31March 8, 2000 1:33 pm
F
Enter the channel position.
G
Set the tape speed.
Press
SP/LP
(
p
).
H
Set the VPS/PDC mode.
Press
VPS/PDC
to select “ON” or “OFF”.
●If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC”
is lit on the front display panel, VPS/PDC is set to ON.
●If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC”
is not lit on the front display panel, VPS/PDC is set to OFF.
墌
“VPS/PDC Recording” in the right column
I
Return to the normal screen.
After confirming all information is correct, press
PROG
or
OK
. “PROGRAM COMPLETED” appears on the TV
screen for about 5 seconds, then the normal screen
appears. If “PROGRAM OVERLAPPED” appears on the
TV screen and “Err” on the front display panel, see
page 33.
●Repeat steps
1
–
9
for each additional programme.
J
Engage the recorder’s timer mode.
Press
#
(
TIMER
). The recorder turns off automatically
and “
#
” appears on the front display panel.
●To disengage the timer mode, press
# (
TIMER
) again.
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps
2
through
9
, press
WEEKLY
(
NUMBER
key “
9
”) for weekly serials or
DAILY
(
NUMBER
key “
8
”) for daily
serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears
on the TV screen. Pressing the button again makes the
corresponding indication disappear.
NOTE:
You can programme this recorder to timer-record as many as 8
programmes. If you try to programme the recorder to record a
ninth, “PROGRAM FULL” appears on the TV screen and “FULL”
appears on the front display panel. To record the extra
programme, you must first cancel any unnecessary programmes
(
墌
pg. 32).
Press
PR+/–
.
Satellite Receiver Users
To timer-record a satellite broadcast using Express Timer
Programming:
APerform “Satellite Receiver Control Setting” on page 15.
BPerform steps
1
–
10
. In step
6
, press the
NUMBER
key
“
0
” to change “TV PROG” to “SAT”. The front display
panel shows “L2” for the channel position. Then press
PR+/–
to enter the channel position for the satellite
broadcast. In step
8
, you cannot set “VPS/PDC” to “ON”.
CLeave the satellite receiver’s power on.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
NOTES:
●When you use Express Timer Programming, set the start
time (VPS or PDC time) exactly as advertised in the TV
listing. A different time than advertised will result in no
recording.
●VPS/PDC recording is also possible when a satellite
receiver or a cable system is connected to AV2 (L-2) IN/
DECODER connector on your recorder.
●VPS/PDC recording is also possible via the AV1 (L-1) IN/
OUT connector.
How to check if the station being received transmits a
VPS/PDC signal
APress
– –:– –
until the channel position appears on the
front display panel.
BHold down
START+
for about 5 seconds.
“VPS/PDC” appears blinking on the front display panel.
If a VPS/PDC signal is detected from the station,
“VPS/PDC” will stop blinking.
If no VPS/PDC signal is detected from the station,
“VPS/PDC” will blink at a slower rate.
CPress
– –:– –
or
START+
again to return to normal display.
HRS7700EU2.fm Page 31 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
32
EN
Page 32March 8, 2000 1:33 pm
TIMER RECORDING (cont.)
Check, cancel and change programmes
A
Disengage the timer mode.
Press
#
(
TIMER
), then press
1
.
B
Access the Programme Check screen/display.
C
Access the Programme screen/display.
The front display panel shows the programme start time. Pressing
OK
changes the display to the programme stop time, then the
date and the channel position.
To cancel or change a programme...
D
Cancel or change a programme.
Press
&
to cancel a programme. To change programme
settings, press the appropriate button:
START+/–
,
STOP+/–
,
DATE+/–
,
PR+/–
,
VPS/PDC
and/or
SP/LP
(
p
).
●You can change “TV PROG” to “SAT” for the channel position
by pressing the
NUMBER
key “
0
”.
E
Return to the normal screen/display.
Press
"
as many times as necessary. If there are still
some programmes remaining, go on to step
6
.
F
Return to the timer mode.
Press
#
(
TIMER
).
NOTE:
You can also check the programmes on the front display panel
even if the recorder’s power is off (unless the recorder is in the
Power Save mode
墌
pg. 50) or the recorder is in the Timer
mode; however, it is not possible to cancel or change the
programmes.
Press
"
.
Press
"
again to check
more information. Each time
you press
"
, the next
programme’s information
appears.
HRS7700EU2.fm Page 32 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
33
Filename [HRS7700EU2.fm]
Page 33March 8, 2000 1:33 pm
When programmes overlap each other
If “PROGRAM OVERLAPPED” appears, you have another
programme overlapping the programme you have just made.
The Programme Check screen appears and conflicting
programmes will start blinking.
Example: Programme 1 (you have just made) and
Programme 4 overlap each other.
A
Confirm the overlapping programmes.
Overlapping programmes blink on the TV screen.
B
Select the programme to modify.
Press
rt
, then press
OK
or
e
.
●You can only select one of the overlapping programmes.
NOTE:
If you do not mind this overlap, press
PROG
to finish the timer
programme setting. The programme with the lower programme
number will be recorded and the other one will not be recorded
correctly. If no changes are made for approximately 1 minute,
the recorder will return to the normal screen.
C
Cancel or change programme setting.
To cancel a programme,
press
&
when the Programme
screen you do not want is shown. “PROGRAM
COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen appears.
To change a programme,
press the appropriate button:
START+/–
,
STOP+/–
,
DATE+/–
,
PR+/–
,
VPS/PDC
and/or
SP/LP
(
p
) when the Programme screen on which you
want to make changes is shown, then press
OK
.
“PROGRAM COMPLETED” appears on the TV screen for
about 5 seconds, then the normal screen appears.
NOTE:
If the overlap is not yet solved, or another overlap occurs with
the timer programme setting after making the last correction on a
programme, the conflicting programmes will be shown on the
Programme Check screen again. Repeat the above steps again
until the overlap is solved.
HRS7700EU2.fm Page 33 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
34
EN
Page 34March 8, 2000 1:33 pm
TIMER RECORDING (cont.)
Automatic Satellite
Programme
Recording
This function allows you to automatically record a
satellite programme which is timer-programmed on your
external satellite receiver. Connect a satellite receiver to
the recorder’s AV2 (L-2) IN/DECODER connector and
programme the timer on the satellite receiver. The
recorder starts or stops recording by the signals input
from the satellite receiver. After recording, the recorder’s
power shuts off automatically.
A
Select the L-2 SELECT mode.
Set “L-2 SELECT” to “A/V” or “SAT” (
墌
pg. 37).
●When you select “SAT”, refer to “IMPORTANT” on page 44.
B
Set the tape speed.
Press
SP/LP
(
p
).
C
Engage the Automatic Satellite Programme
Recording mode.
Press and hold
SAT#
for about 2 seconds. The button
lights up and the recorder turns off automatically.
NOTES:
●To disengage the Automatic Satellite Programme Recording mode, press
SAT
#. The button’s light goes off.
●If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.
●In step
3
, if the SAT
# button does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic
Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer
Programming” (
墌
pg. 30) to timer-record a satellite programme.
*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.
●The SAT
# button blinks while Automatic Satellite Programme Recording is in progress.
●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.
●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.
●Pressing the recorder’s
1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and
disengages the Automatic Satellite Programme Recording mode.
●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible
to set different tape speeds for each programme.
●Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may
record slightly longer than the actual length of the programme.
●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not
start Automatic Satellite Programme Recording even though the SAT
# button blinks. When the satellite receiver shuts off once and
is turned back on again, the recorder starts recording.
●You can also record a programme from your cable system in the same way if the system has a timer.
●The B.E.S.T. system (
墌
pg. 27) does not work while Automatic Satellite Programme Recording is in progress.
●Just Clock (
墌
pg. 60) does not work when the Automatic Satellite Programme Recording mode is engaged.
●When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite
Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON”
(
墌
pg. 49).
●After Automatic Satellite Programme Recording, the number of recorded programmes will not be displayed on the front display
panel for the Instant ReView function (
墌
pg. 20).
ATTENTION
●Be sure not to turn on the satellite receiver before the
programme is executed; otherwise, the recorder will start
recording when the satellite receiver’s power is turned on.
●If you have connected another appliance other than a
satellite receiver to the AV2 (L-2) IN/DECODER connector,
be sure not to engage the Automatic Satellite Programme
Recording mode; otherwise, the recorder will start
recording when the connected appliance’s power is turned
on.
●Automatic Satellite Programme Recording and timer-
recording cannot be done at the same time.
Before performing the following steps:
●Make sure the satellite receiver is connected to the recorder’s
AV2 (L-2) IN/DECODER connector. (
墌
pg. 44, 45)
●Programme the timer on the satellite receiver.
●Insert a cassette with the safety tab in place.
HRS7700EU2.fm Page 34 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right
EN
35
Filename [HRS7700EU2.fm]
Page 35March 8, 2000 1:33 pm
EDITING
Edit From A
Camcorder
You can use a camcorder as the source player and your
recorder as the recording deck.
A
Make connections.
A
If the camcorder has no S-VIDEO output connector ...
... connect the camcorder’s AUDIO OUT and VIDEO
OUT connectors to the recorder’s front panel AUDIO
and VIDEO input connectors.
B
If the camcorder has an S-VIDEO output connector ...
... connect the camcorder’s AUDIO OUT and
S-VIDEO OUT connectors to the recorder’s front panel
AUDIO and S-VIDEO input connectors.
●When using a monaural camcorder, connect its AUDIO OUT
connector to the AUDIO L input connector on your recorder.
●When a Master Edit Control-equipped JVC camcorder is used,
the camcorder is capable of controlling the recorder. Refer to
the camcorder’s instruction manual for operating procedure.
B
Set the recorder’s input mode.
Press
AUX
(
NUMBER
key “
0
”) and/or
PR
to select “F-1”
for the AUDIO and VIDEO input connectors, or “S-1” for
the AUDIO and S-VIDEO input connectors, depending
on the connectors being used.
C
Set the edit mode.
See “PICTURE CONTROL” on page 49.
D
Start the camcorder.
Engage the Play mode of the camcorder.
E
Start the recorder.
Engage the Record mode of the recorder.
NOTES:
●All necessary cables can be obtained from your dealer.
●When you select “EDIT” to dub tapes in step
3
, be sure to
select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)
after you finish dubbing the tapes.
A
If the camcorder has no S-VIDEO output connector ...
B
If the camcorder has an S-VIDEO output connector ...
Your recorder
Audio cable (not provided)
VIDEO OUT
AUDIO OUT
Camcorder
VIDEO
input
Player
AUDIO input
EDIT
Video cable (not provided)
Mini-plug cable
(not provided)
(JVC camcorder
only)
To rear panel
PAUSE connector
Your recorder
Audio cable (not provided)
S-VIDEO OUT
AUDIO OUT
Camcorder
S-VIDEO
input
Player
AUDIO input
EDIT
S-Video cable (not provided)
Mini-plug cable
(not provided)
(JVC camcorder
only)
To rear panel
PAUSE connector
HRS7700EU2.fm Page 35 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
36
EN
Page 36March 8, 2000 1:33 pm
EDITING (cont.)
Output/Input Set
L-1 OUTPUT and L-1 INPUT Setting
The AV1 (L-1) IN/OUT connector accepts and delivers either a
composite signal (regular video signal) or a Y/C signal (a signal
in which the luminance and chrominance signals are separated).
Set “L-1 OUTPUT” and “L-1 INPUT” to the appropriate mode
depending on the type of appliance connected to the recorder’s
AV1 (L-1) IN/OUT connector.
A
Access the Main Menu screen.
Press
MENU
.
B
Access the Output/Input Set screen.
C
Select the output or input mode for the AV1
(L-1) IN/OUT connector.
D
Return to the normal screen.
Press
MENU
.
NOTES:
●If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set
“L-1 INPUT” to “S-VIDEO”.
●If “L-2 SELECT” is set to “DECODER”, it is impossible to set
“L-1 INPUT” to “S-VIDEO”.
Press
rt
to move the
highlight bar (pointer) to
“OUTPUT/INPUT SET”, then
press
OK
or
e
.
Press
rt
to move the
highlight bar (pointer) to “L-1
OUTPUT” or “L-1 INPUT”.
Then, press
OK
or
e
to select
the appropriate setting.
*The default setting is
bold
in
the table below.
8
L-1 OUTPUT
VIDEO
:If a connected appliance’s input is
compatible only with regular video
signals, set to “VIDEO”.
S-VIDEO:
If a connected appliance’s input is
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain high-
quality S-VHS picture. (For
connection, be sure to use a 21-pin
SCART cable that is compatible with
the Y/C signal.)
8
L-1 INPUT
VIDEO
:If a connected appliance’s output is
compatible only with regular video
signals, set to “VIDEO”.
S-VIDEO
:If a connected appliance’s output is
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain high-
quality S-VHS picture. (For
connection, be sure to use a 21-pin
SCART cable that is compatible with
the Y/C signal.)
HRS7700EU2.fm Page 36 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
37
Filename [HRS7700EU2.fm]
Page 37March 8, 2000 1:33 pm
L-2 SELECT and L-2 INPUT Setting
The AV2 (L-2) IN/DECODER connector accepts either a
composite signal (regular video signal) or a Y/C signal (a signal
in which the luminance and chrominance signals are separated).
Set “L-2 SELECT” to the appropriate mode depending on the
type of appliance connected to the recorder’s AV2 (L-2) IN/
DECODER connector. Set “L-2 INPUT” to the appropriate mode
depending on the output signals of the connected appliance.
A
Select the input mode for the AV2 (L-2) IN/
DECODER connector.
B
Return to the normal screen.
Press
MENU
.
NOTES:
●If you have a satellite receiver or a decoder connected to the
AV2 (L-2) IN/DECODER connector, be sure to set “L-2
SELECT” back to appropriate mode after editing.
●If you are not connecting a satellite receiver or a decoder to
the AV2 (L-2) IN/DECODER connector, leave “L-2 SELECT” set
to “A/V”.
●The default setting is “A/V”; if the recorder’s memory backup
has expired due to a power cut or because the AC was
removed from the recorder, “A/V” will be automatically
selected when the power is restored to the recorder. If you are
using a satellite receiver or a decoder, be sure to set “L-2
SELECT” back to appropriate mode.
●When “L-2 SELECT” is set to “SAT”, “SAT” appears on TV
screen or front display panel instead of “L-2” or “L2”.
●If “L-2 SELECT” is set to “DECODER”, it is impossible to set
“L-2 INPUT” to “S-VIDEO”.
●If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set
“L-2 SELECT” to “DECODER”.
Perform steps
1
and
2
of “L-1 OUTPUT and L-1 INPUT
Setting” on page 36.
Press
rt
to move the
highlight bar (pointer) to “L-2
SELECT
” or “L-2 INPUT”.
Then, press
OK
or
e
to select
the appropriate setting.
*The default setting is
bold
in
the table below.
8
L-2 SELECT
A/V
:To use this recorder as the recording
deck with the player connected to
the AV2 (L-2) IN/DECODER
connector, or to use the satellite
receiver connected to the AV2 (L-2)
IN/DECODER connector.
DECODER
:To use a decoder connected to the
AV2 (L-2) IN/DECODER connector.
SAT
:To view a satellite programme with
the TV set while the recorder is
turned off. (
墌
pg. 44)
8
L-2 INPUT
VIDEO
:If a connected appliance’s output is
compatible only with regular video
signals, set to “VIDEO”.
S-VIDEO
:If a connected appliance’s output is
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain high-
quality S-VHS picture. (For
connection, be sure to use a 21-pin
SCART cable that is compatible with
the Y/C signal.)
HRS7700EU2.fm Page 37 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
38
EN
Page 38March 8, 2000 1:33 pm
EDITING (cont.)
Edit To Or From
Another Video
Recorder
You can use your recorder as the source player or as the
recording deck.
A
Make connections.
Connect the player’s 21-pin SCART connector to the
recorder’s 21-pin SCART connector as illustrated on
page 39.
A
When using your recorder as the source player ...
... connect its AV1 (L-1) IN/OUT connector to the
recording deck.
B
When using your recorder as the recording deck ...
... connect its AV1 (L-1) IN/OUT or AV2 (L-2) IN/
DECODER connector to the source player.
C
If another recorder is compatible with the Y/C signal ...
... connect your recorder’s AV1 (L-1) IN/OUT
connector to another recorder.
With
C
connection ...
●When using your recorder as the recording deck, set “L-1
INPUT” to “S-VIDEO” and “L-2 SELECT” to “A/V” (
墌
pg. 36,
37).
●When using your recorder as the source player, set “L-1
OUTPUT” to “S-VIDEO” (
墌
pg. 36).
B
Set the input mode of recording deck.
With this video recorder, press
AUX
(
NUMBER
key “
0
”)
and/or
PR
to select “L-1” for the AV1 (L-1) IN/OUT
connector, or “L-2” for the AV2 (L-2) IN/DECODER
connector, depending on the connector being used.
●When using another recorder as the recording deck, refer to its
instruction manual.
●When using the AV2 (L-2) IN/DECODER connector, set “L-2
SELECT” to “A/V” (
墌
pg. 37).
C
Set the edit mode.
See “PICTURE CONTROL” on page 49.
D
Start the source player.
Engage the Play mode of the source player.
E
Start the recording deck.
Engage the Record mode of the recording deck.
Advantages of S-VHS video recorders
You can edit from VHS to S-VHS, S-VHS to VHS, or, from
S-VHS to S-VHS.
●From VHS to S-VHS: Record VHS playback signals in the
S-VHS mode. Although the picture quality is inherently
limited by that of the original, the edited tape has better
picture quality than those made by VHS-to-VHS editing.
●From S-VHS to VHS: Because the picture quality of the
source material is very high, the edited tape has better
picture quality than those made by VHS-to-VHS editing.
●From S-VHS to S-VHS: All signals will be transferred with
minimum degradation.
HRS7700EU2.fm Page 38 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-Full-NoTitle0
EN
39
Filename [HRS7700EU2.fm]
Page 39March 8, 2000 1:33 pm
NOTES:
●All necessary cables can be obtained from your dealer.
●For Y/C signal input/output, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.
●When you select “EDIT” to dub tapes in step
3
, be sure to select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”) after you
finish dubbing the tapes.
●When you use this recorder as the source player for editing, be sure to set “O.S.D.” to “OFF” before starting (
墌
pg. 49).
●If you are using another recorder with S-Video and Audio input/output connectors, you can connect those connectors to this
recorder’s S-VIDEO and AUDIO input/output connectors.
When using your recorder as the source player ...
... connect its rear panel S OUT and AUDIO OUT connectors to the recording deck’s S-Video and Audio input connectors.
When using your recorder as the recording deck ...
... connect its front panel S-VIDEO and AUDIO input connectors to the source player’s S-Video and Audio output connectors. Then,
set the recorder’s input mode to “S-1”.
Video
channel or
AV mode
21-pin SCART cable
(not provided)
RecorderYour recorder
Another recorder
Player
TV receiver
RF cable
(provided)
AB
Video
channel or
AV mode
21-pin SCART cable
(not provided)
Recorder
Your recorder
Another recorder
Player
TV receiver
RF cable
(provided)
C
21-pin SCART cable
(not provided)
Recorder
Your recorder
Another recorder
Player
TV receiver
S-Video cable
(not provided)
HRS7700EU2.fm Page 39 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
40
EN
Page 40March 8, 2000 1:33 pm
EDITING (cont.)
Audio Dubbing
Audio Dubbing replaces the normal audio sound of a
previously recorded tape with a new soundtrack.
Normal audio track
Video/Hi-Fi audio
track
Pre-recorded tape
Audio-dubbed tape
CD player, etc.
Your recorder
CD player, etc.
Mixer
output
Audio mixer
Original sound
AUDIO OUT
Your recorder
HRS7700EU2.fm Page 40 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
41
Filename [HRS7700EU2.fm]
Page 41March 9, 2000 3:45 pm
A
Make connections.
Connect an audio component to the AUDIO L + R input
connectors on the recorder’s front panel.
●When connecting a monaural audio component, use only the
recorder’s AUDIO L input connector.
B
Set the recorder’s input mode.
Press
AUX
(
NUMBER
key “
0
”) and/or
PR
to select “F-1”
or “S-1”.
C
Locate the start point.
Press
4
to start playback of the tape in your recorder, and
press
9
when you reach the point where you want to start
dubbing.
D
Engage the Audio Dubbing mode.
Press
A.DUB
.
●Your recorder enters the Audio Dubbing Pause mode. (“
o”
blinks, “
u” and “i” light up on the front display panel.)
●To perform Audio Dubbing with audio mixing, press
AUDIO
on the remote control to select “
a + s (L+R)” at this point.
*Audio Dubbing with audio mixing is not possible if you are using a
monaural audio component, or if you don’t have an audio mixer.
E
Start dubbing.
Engage the audio component’s Play mode, then press
4
to start the tape in your recorder; Audio Dubbing begins
at this point.
●“
o” blinks and “u” is displayed on the front display panel.
●To stop dubbing temporarily, press
9. Press 4 to resume
dubbing.
F
End Audio Dubbing.
Press
8
(or
0
) to stop the tape in your recorder, and
engage the audio component’s Stop mode.
NOTES:
●
When monitoring the sound during Audio Dubbing, the
normal soundtrack is automatically selected. If you wish to
hear the mixed sound (Hi-Fi + Normal soundtracks), press
AUDIO
on the remote control to select “
a
+
s
(L+R) +
NORM” (
墌
pg. 22).
●
Audio Dubbing stops automatically when the counter reaches
“0:00:00”, and the recorder enters the Play mode. Check the
counter reading before dubbing.
●
Audio Dubbing is also possible using the rear panel AV1 (L-1)
IN/OUT or AV2 (L-2) IN/DECODER connector. When using
these 21-pin SCART connectors, be sure to select the correct
input mode (“L-1” or “L-2”) in step
2
.
●
Audio Dubbing is not possible with cassettes whose record
safety tab has been removed.
●
When playing back an audio-dubbed tape, press
AUDIO
on
the remote control to select the soundtrack you wish to hear
(
墌
pg. 22).
HRS7700EU2.fm Page 41 Thursday, March 9, 2000 3:45 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
42
EN
Page 42March 8, 2000 1:33 pm
EDITING (cont.)
Insert Editing
Insert Editing replaces part of the recorded scene with
new material. Both the picture and Hi-Fi audio
soundtrack are replaced with new ones, while the
normal audio soundtrack remains unchanged. If you
wish to change the normal audio track as well, use the
Audio Dubbing function simultaneously.
For Insert Editing, use your recorder as the recording
deck.
Source tape
Recording tape
Before Insert Editing
Normal audio
track
After Insert Editing
Video/Hi-Fi
audio track
Another recorder
Audio/Video signalS-Video signal
Recorder
Your recorder
Player
HRS7700EU2.fm Page 42 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
43
Filename [HRS7700EU2.fm]
Page 43March 9, 2000 3:46 pm
A
Make connections.
Connect the player’s VIDEO OUT or S-VIDEO OUT and
AUDIO OUT connectors to your recorder’s VIDEO or
S-VIDEO and AUDIO input connectors on the front
panel.
B
Set the recorder’s input mode.
Press
AUX
(
NUMBER
key “
0
”) and/or
PR
to select “F-1”
for the AUDIO and VIDEO input connectors or “S-1” for
AUDIO and S-VIDEO input connectors.
C
Locate the end point.
Load the recording cassette into your recorder, and play it
back to determine the edit-out point (the end of the
segment to be replaced) using the
SHUTTLE
ring or the
JOG
dial, or pressing
w
e
and
9
.
D
Reset the counter.
Press
0000
.
●
The counter is reset to “0:00:00”.
E
Locate the start point.
Determine the edit-in point (the beginning of the segment
to be replaced) using the
SHUTTLE
ring or the
JOG
dial,
or pressing
w
e
and
9
.
●
Be sure to engage the Still mode at the edit-in point.
F
Engage the Insert Editing mode.
Press
INSERT
.
●
Your recorder enters the Insert Pause mode. (“
o”, “u” and
“
i” light up on the front display panel.)
●
The TV screen changes from the still picture to the input
source you are going to record.
G
Start Editing.
Load the source cassette and play back the segment that
is to be inserted. When you reach the start of the section
of the source tape that you wish to insert, press
4
to start
the tape in your recorder; Insert Editing begins at this
point.
●
“
o” and “u” are displayed on the front display panel.
H
End Insert Editing.
At counter “0:00:00”, Insert Editing will stop
automatically while the tape continues running in the
Play mode. If you wish to stop Insert Editing before the
specified edit-out point, press
0000
.
AV Insert Editing
If you want to replace the picture, Hi-Fi audio soundtrack
and normal audio soundtrack all at the same time ...
... In step
6
, after you press
INSERT
, press
A.DUB
also.
(“
o
” and “
u
” blink and “
i
” lights up on the front display
panel.)
NOTES:
●
All necessary cables can be obtained from your dealer.
●
Insert Editing is not possible with cassettes whose record safety
tab has been removed.
●
When Insert Editing is performed on a tape that has been
recorded on another video recorder, the inserted portion may
appear distorted.
●
In Insert Editing, the recording speed (SP/LP) is determined by
the previous recording to be replaced. If the previous
recording’s speed changes within a single edit, the inserted
picture will be distorted at the switching point.
●
A small portion of the recording which precedes an insert edit
may become erased.
●
Insert Editing is also possible using the rear panel AV1 (L-1) IN/
OUT or AV2 (L-2) IN/DECODER connector. When using these
21-pin SCART connectors, be sure to select the correct input
mode (“L-1” or “L-2”) in step 2.
HRS7700EU2.fm Page 43 Thursday, March 9, 2000 3:46 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
44
EN
Page 44March 8, 2000 1:33 pm
SYSTEM CONNECTIONS
Connecting To A Satellite Receiver
Simple Connections
This is an example of simple connection if your TV has
one 21-pin AV input (SCART) connector.
Connect the satellite receiver to the AV2 (L-2) IN/
DECODER connector, then connect the AV1 (L-1) IN/
OUT connector to the TV’s connector.
NOTES:
●Set “L-2 SELECT” to “A/V” (
墌
pg. 37).
●You can use Automatic Satellite Programme Recording
function (
墌
pg. 34) with this connection.
●To record a programme via the satellite receiver, select L-2
mode by pressing
AUX
(
NUMBER
key “
0
”) and/or
PR
so that
“L-2” appears on the front display panel.
●For details, refer to the instruction manual of the satellite
receiver.
IMPORTANT
When you set “L-2 SELECT” to “SAT” (
墌
pg. 37), it is possible to view a satellite broadcast with the TV set to its AV mode even if
the recorder is turned off. When the recorder is in Stop mode or recording, press
TV/VCR
on the remote control to turn off the VCR
indicator on the front display panel.
●If you turn on the recorder when the satellite receiver’s power is off, nothing appears on the TV screen. In this case, turn on the
satellite receiver, or set the TV to its TV mode, or press
TV/VCR
on the remote control to set the recorder to the video mode.
Outdoor unit
Satellite cable
Satellite receiver
Aerial
TV aerial cable
21-pin SCART connector
Back of TV
ANT. IN
RF OUT
Aerial
connector
Mains outlet
Back of recorder
HRS7700EU2.fm Page 44 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
45
Filename [HRS7700EU2.fm]
Page 45March 8, 2000 1:33 pm
Perfect Connections
This is an example of recommended connection if your
TV has two 21-pin AV input (SCART) connectors.
Connect the decoder to the satellite receiver’s connector
if you have a decoder, AV1 (L-1) IN/OUT connector to
TV’s connector, and AV2 (L-2) IN/DECODER connector
to the satellite receiver’s connector. Then connect the
satellite receiver and TV.
NOTES:
●Set “L-2 SELECT” to “A/V” (
墌
pg. 37).
●You can use Automatic Satellite Programme Recording
function (
墌
pg. 34) with this connection.
●To record a programme via the satellite receiver, select L-2
mode by pressing
AUX
(
NUMBER
key “
0
”) and/or
PR
so that
“L-2” appears on the front display panel.
●To receive a scrambled broadcast, descramble the signal with
the satellite receiver.
●For details, refer to the instruction manual of the satellite
receiver and decoder.
Outdoor unit
Satellite cable
Satellite receiver
Aerial
TV aerial cable
21-pin SCART
connector
Back of TV
ANT. IN
RF OUT
Aerial
connector
Decoder
Mains outlet
Back of recorder
HRS7700EU2.fm Page 45 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU2.fm]
Masterpage:Left
46
EN
Page 46March 8, 2000 1:33 pm
SYSTEM CONNECTIONS (cont.)
Connecting/Using
A Decoder
The AV2 (L-2) IN/DECODER connector can be used as an
input connector for an external decoder (descrambler).
Simply connect a decoder and you can enjoy the variety
of programming that is available through scrambled
channels.
A
Select the input mode.
Set “L-2 SELECT” to “DECODER”. (
墌
pg. 37)
B
Connect the decoder.
Connect your recorder’s AV2 (L-2) IN/DECODER
connector to the decoder’s 21-pin SCART connector
using a 21-pin SCART cable.
C
Set the tuner.
Perform the procedure as described in “When Receiving
A Scrambled Broadcast” on page 55.
TV receiver
RF cable
(provided)
TV aerial
cable
AV1 (L-1) IN/OUTAV2 (L-2) IN/DECODER
Decoder
HRS7700EU2.fm Page 46 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
47
Filename [HRS7700EU2.fm]
Page 47March 8, 2000 1:33 pm
Connecting/Using A Stereo System
These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to
the soundtrack through the stereo.
Make connections.
Connect the AUDIO OUT L and R connectors on your
video recorder to the AUX IN or TAPE MONITOR
connectors on your stereo system’s receiver or amplifier.
NOTE:
When listening to sound through the connected stereo system,
turn the TV’s volume down completely.
CAUTIONS:
●This recorder has a dynamic range of more than 80 dB with
regards to its Hi-Fi audio capability. It is recommended that
you check the maximum level if you are going to listen to the
Hi-Fi audio signals through a stereo amplifier. A sudden surge
in the input level to the speakers may damage them.
●Some speakers and televisions are specially shielded to
prevent television interference. If both are of the non-shielded
type, do not place the speakers adjacent to the TV set as this
can adversely affect the video playback picture.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
FM tuner
CD player
Stereo amplifier
AUX IN or TAPE MONITOR
Audio cable
(not provided)
SpeakerTelevisionSpeaker
Mains outlet
Back of recorder
AUDIO OUT
HRS7700EU2.fm Page 47 Wednesday, March 8, 2000 1:33 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU3.fm]
Masterpage:Left
48
EN
Page 48March 8, 2000 1:58 pm
SUBSIDIARY SETTINGS
Mode Set
You can change various mode settings on the Mode Set
screen by following the procedure described below.
●
For each mode setting, see pages 49 to 51.
A
Access the Main Menu screen.
Press
MENU
.
B
Access the Mode Set screen.
C
Select the mode.
Press
rt
to move the highlight bar (pointer) to the item
you want to change.
D
Select the mode setting.
Press
OK
or
e
.
E
Return to the normal screen.
Press
MENU
.
Turn on the TV and select the video channel (or
AV mode).
Press
rt
to move the
highlight bar (pointer) to
“MODE SET”, then press
OK
or
e
.
HRS7700EU3.fm Page 48 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-Full-NoTitle0
EN
49
Filename [HRS7700EU3.fm]
Page 49March 8, 2000 1:58 pm
* The default setting is
bold
in the table below.
8
B.E.S.T.
ON
OFF
You can set the B.E.S.T. (Biconditional Equalised Signal
Tracking) system to “ON” or “OFF” (
墌
pg. 27).
8
PICTURE CONTROL
AUTO
:Provides the optimised picture
benefits of the B.E.S.T. Picture
System.
EDIT
:Minimizes picture degradation
during editing (recording and
playback).
SOFT
:Reduces image coarseness when
viewing overplayed tapes containing
a lot of noise.
SHARP
:Clearer, sharper-edged picture when
viewing images with lots of flat,
same-coloured surfaces such as
cartoons.
This feature helps you to adjust the playback picture
quality according to your preference. Normally select
“AUTO”.
NOTES:
●
When you select “EDIT”, “SOFT” or “SHARP”, the selected
mode will not change until you select another mode.
●
When you select “EDIT” to dub tapes, be sure to select “AUTO”
after you finish dubbing the tapes.
●
When “B.E.S.T.” is “OFF”, “PICTURE CONTROL” switches
automatically from “AUTO” to “NORM”.
8
AUTO TIMER
ON
OFF
When this function is set to “ON”, the timer is
automatically engaged when the recorder power is turned
off, and automatically disengaged when the recorder is
powered back on.
NOTE:
For safety, when “AUTO TIMER” is set to “OFF”, all other recorder
functions are disabled while the Timer mode is engaged. To
disengage the timer, press
# (TIMER).
8
O.S.D.
ON
OFF
When this function is set to “ON”, various operational
indicators appear on the TV screen. Messages appear in
the selected language (
墌
pg. 13, 14).
NOTES:
●
When you use this recorder as the source player for editing, be
sure to set “O.S.D.” to “OFF” before starting.
●
During playback, the operation mode indicators may be
disturbed depending on the type of tape being used.
8
DIRECT REC
ON
OFF
When this function is set to “ON”, you can easily start
recording the programme that you are watching on your
TV. Press and hold
7
and press
4
on the remote control,
or press
7
on the recorder.
NOTES:
●
When you use the Direct Rec function, be sure to use a TV
offering T-V LINK, etc. and connect a fully-wired 21-pin SCART
cable between the recorder and the TV (
墌
pg. 8).
●
If “DIRECT REC” is set to “OFF”, the
7 button functions as
described in “Basic Recording” (
墌
pg. 23).
●
During the Direct Rec, “– –” appears on the front display panel.
●
Retake function (
墌
pg. 26) does not work during Direct Rec.
HRS7700EU3.fm Page 49 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Left-FullCol
50
EN
Filename [HRS7700EU3.fm]
Page 50March 8, 2000 1:58 pm
SUBSIDIARY SETTINGS (cont.)
* The default setting is
bold
in the table below.
8
AUTO SP
]
LP TIMER
ON
OFF
When this function is set to “ON”, the recorder
automatically switches to LP mode to allow complete
recording if there is not enough tape to record the entire
programme while timer-recording in SP mode.
For Example . . .
Recording a programme of 210 minutes in length onto a
180-minute tape
Make sure you set this function to “ON”, before the timer-
recording starts.
NOTES:
●
If you have programmed the recorder to timer-record 2 or more
programmes, the second programme and those thereafter may
not fit on the tape if you set “AUTO SP
]LP TIMER” to “ON”. In
this case, make sure the mode is not engaged, then set the tape
speed manually during timer programming.
●
In order to ensure that the recording fits on the tape, this feature
may leave a slight non-recorded section at the end of the tape.
●
There may be some noise and sound disturbance at the point on
the tape where the recorder switches from SP to LP mode.
●
The Auto SP
]LP Timer feature is not available during ITR
(Instant Timer Recording), and the feature will not work properly
with any tapes longer than E-180, or with some tapes of shorter
lengths.
●
If you perform timer recording with both VPS/PDC and the Auto
SP
]LP Timer activated, and the programme goes beyond its
originally scheduled length, there may be times when the
programme cannot be recorded in its entirety.
8
DIGITAL 3R
ON
OFF
When this function is set to “ON”, the Digital 3R picture
system applies edge correction to the luminance signal to
enhance detail.
NOTES:
●
Normally it is recommended to keep “DIGITAL 3R” set to
“ON”.
●
Depending on the type of tape being used, picture quality may
be better with “DIGITAL 3R” set to “OFF”.
●
If you use the recorder as the source player for editing, be sure
to set “DIGITAL 3R” to “OFF” before starting.
8
POWER SAVE
ON
OFF
When this function is set to “ON”, you can reduce the
power consumption while the recorder is turned off.
NOTES:
●
During Power Save mode ...
... the front display panel will be turned off.
... the Just Clock function (
墌
pg. 60) does not work.
... the picture may be distorted momentarily when you turn on/
off the recorder.
●
Power Save does not work when ...
... the recorder is in the Timer mode.
... the recorder’s power is turned off after timer-recording or
Instant Timer Recording.
... the Automatic Satellite Programme Recording mode is
engaged (
墌
pg. 34).
... “L-2 SELECT” is set to “DECODER” or “SAT” (
墌
pg. 37).
Total 210 minutes
Approximately 150 minutes Approximately 60 minutes
SP modeLP mode
HRS7700EU3.fm Page 50 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-Full-NoTitle0
EN
51
Filename [HRS7700EU3.fm]
Page 51March 8, 2000 1:58 pm
* The default setting is
bold
in the table below.
8
S-VHS
ON
OFF
Your recorder can record in S-VHS (Super VHS), S-VHS ET
or VHS.
●
To record in S-VHS:
Set “S-VHS” to “ON”. Then, insert a cassette marked
“S-VHS”. The S-VHS indicator lights up on the front
display panel.
The S-VHS recording mode is selected.
●
To record in S-VHS ET on a VHS cassette:
See “Super VHS ET (S-VHS ET)” on page 25.
●
To record in VHS:
Insert a cassette marked “VHS”.
If the S-VHS ET button on the recorder is lit and the
S-VHS ET mode is activated, press
S-VHS ET
. The button’s
light goes off.
The VHS recording mode is automatically selected
regardless of the “S-VHS” mode setting.
●
To record in VHS on an S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator
lights up on the front display panel. Then, set “S-VHS” to
“OFF”. The S-VHS indicator goes off.
The VHS recording mode is selected.
NOTE:
When playing back a tape that has been recorded in S-VHS or
S-VHS ET, the S-VHS indicator lights up on the front display panel
regardless of the “S-VHS” mode setting.
8
COLOUR SYSTEM
PAL/NTSC
:To record PAL signals, or play back a
PAL or NTSC tape.
MESECAM
:To record SECAM signals, or play
back a MESECAM tape.
You can play back PAL, NTSC and MESECAM tapes, or
record PAL and SECAM* signals on this recorder. Select the
appropriate colour system.
*SECAM signals will be recorded as MESECAM on this recorder;
MESECAM is the designation for tapes with SECAM signals that
have been recorded on a MESECAM-compatible PAL video
cassette recorder.
NOTES:
About NTSC Playback
●
Some TVs shrink the picture vertically and place black bars at
the top and bottom of the TV screen. This is not a malfunction
on the part of either the video recorder or the TV.
●
The picture may roll up and down. This can be corrected using
the V-HOLD control found on some TVs. (This cannot be
corrected if the TV does not have a V-HOLD control.)
●
The counter and tape remaining time readings will be incorrect.
●
During search, still, or frame-by-frame playback, the picture will
be distorted, and there may be a loss of colour.
●
Depending on the type of TV, the top and bottom portions of
superimposed displays may be cut off during NTSC playback.
HRS7700EU3.fm Page 51 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU3.fm]
Masterpage:Left
52
EN
Page 52March 8, 2000 1:58 pm
SUBSIDIARY SETTINGS (cont.)
Tuner Set
Your recorder needs to memorize all necessary stations in
channel positions in order to record TV programmes. Auto
Channel Set automatically assigns all receivable stations in your
area to call them up by using the
PR
buttons without going
through any vacant channels.
Auto Channel Set
A
Turn on the recorder.
Press
1
.
B
Access the Main Menu screen.
Press
MENU
.
C
Access the Auto Channel Set screen.
D
Select your country.
Press
rt
to move the highlight bar (pointer) to your
country’s name, then press
OK
or
e
.
E
Select the language.
Press
rt
to move the highlight bar (pointer) to the
language of your choice.
Turn on the TV and select the video channel (or
AV mode).
IMPORTANT
Perform the following steps only if —
— Auto Channel Set has not been set correctly by Auto Set
Up or by Preset Download (
墌
pg. 10, 12).
— you have moved to a different area or if a new station
starts broadcasting in your area.
Press
rt
to move the
highlight bar (pointer) to
“AUTO CH SET”, then press
OK
or
e
.
HRS7700EU3.fm Page 52 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
53
Filename [HRS7700EU3.fm]
Page 53March 8, 2000 1:58 pm
NOTES:
●
Fine tuning is performed automatically during Auto Channel
Set. If you want to perform tuning manually, refer to page 56.
●
If you perform Auto Channel Set when the aerial cable is not
connected properly, “SCAN COMPLETED -NO SIGNAL-”
appears on the TV screen in step
7
. When this happens, make
sure of the aerial connection and press
OK
; Auto Channel Set
will take place again.
●
If no sound accompanies the picture or the audio sounds
unnatural on some channels that have been stored by Auto Set
Up, the TV system setting for those channels may be incorrect.
Select the appropriate TV system for those channels
(
墌
pg. 55, “INFORMATION”).
F
Perform Auto Channel Set.
Press
OK
twice.
●
If you have connected the
recorder and your TV via AV
connection (
墌
pg. 8), the
recorder automatically
performs the Preset
Download and the T-V LINK
screen will appear
(
墌
pg. 12).
●
The Auto Set screen appears,
and remains on screen while
the recorder searches for
receivable stations.
As Auto Channel Set progresses, the “
q” mark on the TV screen
moves from left to right. Wait until the TV screen as shown in
step
7
appears.
G
View the Confirmation screen.
After “SCAN COMPLETED” is
displayed on the TV screen for
about 5 seconds, the
Confirmation screen looking
like the one to the right
appears. The stations your
recorder located appear on a
Confirmation screen —
channel positions (PR),
channels (CH) and station names (ID –
墌
pg. 57). The
blueback screen and the programme currently being
broadcast by the blinking station appear alternately for 8
seconds each. To view the next page, use the
rt
w
e
button on the remote control.
●
The stations located in the selected country appear at the top
of the list.
●
The Guide Program numbers will also be set automatically
during Auto Channel Set.
H
Return to the normal screen.
Press
MENU
.
●
Using the Confirmation screen, you can skip or add channel
positions, enter station names and perform other operations.
Refer to pages 54 – 56 for the procedures.
●
Depending on reception conditions, the stations may not be
stored in order, and the station names may not be stored
correctly.
●
For information on scrambled broadcasts, refer to page 55.
IMPORTANT
●
In certain reception conditions, station names may not be
stored correctly, and Auto Guide Program Number Set may
not work properly. If the Guide Program numbers are not
set properly when you timer-record a TV programme using
the S
HOW
V
IEW
system, the recorder will record a TV
programme of a different station. When programming the
timer using the S
HOW
V
IEW
system, be sure to check the
desired channel is selected correctly (
墌
pg. 28,
“S
HOW
V
IEW
®
Timer Programming”).
●
Your video recorder memorizes all detected stations even if
reception of some of them is poor. You can delete those
stations with an unacceptable picture (
墌
pg. 55, “Delete
A Channel”).
BeginningEnd
HRS7700EU3.fm Page 53 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU3.fm]
Masterpage:Left
54
EN
Page 54March 8, 2000 1:58 pm
SUBSIDIARY SETTINGS (cont.)
Manual Channel Set
Store channels that were not stored during Auto Set Up
(
墌
pg. 10), Preset Download (
墌
pg. 12) or Auto Channel Set
(
墌
pg. 52).
A
Access the Main Menu screen.
Press
MENU
.
B
Access the Confirmation screen.
Press
rt
to move the highlight bar (pointer) to
“MANUAL CH SET”, then press
OK
or
e
. The
Confirmation screen appears.
C
Select the channel position.
Press
rt
w
e
until an open
position in which you want to
store a channel begins blinking,
then press
OK
. The Manual
Channel Set screen appears.
D
Select the band.
E
Input the channel.
Press the
NUMBER
keys to input the channel number you
want to store.
●
Input “0” before any single number entries.
●
To input the registered station name (ID –
墌
pg. 57), press e
until “– – – –” (ID setting) begins blinking, then press
rt.
●
For fine tuning adjustment, press
e until “+/–” begins blinking,
then press
rt. While tuning, “+” or “–” appears.
●
When storing a channel that sends scrambled broadcasts,
press
e until “OFF” (Decoder setting) blinks, then press rt to
set “DECODER” to “ON” (“OFF” is the default setting).
●
When “L-2 SELECT” is set to “A/V” or “SAT”, the “DECODER”
setting cannot be changed (
墌
pg. 37).
F
Enter new channel information.
Press
OK
and the Confirmation screen appears.
●
Repeat steps
3
–
6
as necessary.
G
Close the Confirmation screen.
Press
MENU
.
●
To change positions, see “Change Station Channel Position”
(
墌
pg. 55).
●
If you wish to set station names other than the ones registered
in your recorder, see “Set Stations (B)” (
墌
pg. 56).
The blueback screen and the
programme currently being
broadcast by the selected
channel appear alternately for
8 seconds each.
(E
xamp
l
e
)
T
o store
i
n pos
i
t
i
on
12.
Press
rt
to change the band
between CH (regular) and CC
(cable), then press
e
.
ATTENTION
Guide Program numbers are not set when channels are
stored manually. If an attempt is made at timer programming
with the S
HOW
V
IEW
system in this state, the “GUIDE PROG
SET” screen appears; set the Guide Program numbers on this
screen. (
墌
pg. 29, “ATTENTION — Guide Program
Number Set”)
Or perform “Guide Program Number Set” (
墌
pg. 59).
HRS7700EU3.fm Page 54 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
55
Filename [HRS7700EU3.fm]
Page 55March 8, 2000 1:58 pm
Delete A Channel
A
Select the item.
Press
rt
w
e
until the item you want to delete begins
blinking.
B
Delete a channel.
Press
&
.
●
The item directly beneath the cancelled one moves up one
line.
●
Repeat steps
1
and
2
as necessary.
C
Close the Confirmation screen.
Press
MENU
.
Change Station Channel Position
A
Select the item.
Press
rt
w
e
until the item you want to move begins
blinking. Then press
OK
and the station name (ID) and its
channel (CH) number begin blinking.
B
Select the new position.
Press
rt
w
e
to move the station to the new channel
position, then press
OK
.
Example:If you moved the station in position 4 to position 2, the
stations originally in positions 2 and 3 each move
down one space.
●
Repeat steps
1
and
2
as necessary.
C
Close the Confirmation screen.
Press
MENU
.
When Receiving A Scrambled
Broadcast
A
Select the decoder mode.
Set “L-2 SELECT” to “DECODER” (
墌
pg. 37).
B
Access the Confirmation screen.
Perform steps
1
and
2
of “Manual Channel Set” on
page 54.
C
Select the position.
Press
rt
w
e
to select the channel position broadcasting
scrambled programmes, then press
OK
twice
.
D
Change the decoder setting.
Press
e
until “OFF” (decoder setting) begins blinking, and
set it to “ON” by pressing
rt
.
E
Return to the Confirmation screen.
Press
OK
.
●
Repeat steps
3
–
5
as necessary.
F
Close the Confirmation screen.
Press
MENU
.
Perform steps
1
and
2
of “Manual Channel Set” on page 54
to access the Confirmation screen before continuing.
Perform steps
1
and
2
of “Manual Channel Set” on page 54
to access the Confirmation screen before continuing.
INFORMATION
If you live in Eastern Europe, “TV SYSTEM” setting appears
instead of “DECODER” setting on the Manual Channel Set
screen. When you can see the picture but can hear no audio,
select appropriate TV system (D/K or B/G). Normally, TV
programmes are broadcasted as follows.
For Eastern Europe : D/K
For Western Europe : B/G
ASelect a country in Eastern Europe in step
4
on page 52.
BPress
e until the TV system (D/K or B/G) blinking on the
Manual Channel Set screen in step
4
on page 54.
CPress
rt to select appropriate TV System (D/K or B/G).
HRS7700EU3.fm Page 55 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU3.fm]
Masterpage:Left
56
EN
Page 56March 8, 2000 1:58 pm
SUBSIDIARY SETTINGS (cont.)
Set Stations (A)
Set station names that are registered in your recorder.
A
Select the item.
Press
rt
w
e
until the item you want begins blinking.
B
Access the Manual Channel Set screen.
Press
OK
twice.
C
Select the new station.
D
Switch the stations.
Press
OK
.
●
The Confirmation screen appears.
●
Repeat steps
1
–
4
as necessary.
E
Close the Confirmation screen.
Press
MENU
.
Set Stations (B)
Set station names other than the ones registered in your recorder.
A
Select the character for station name.
B
Enter the new character.
Press
rt
to cycle through the characters (A–Z, 0–9, –,
f
,
+,
I
(space) ) and stop when the desired character is
indicated, then press
e
to enter. Enter the remaining
characters the same way (maximum of 4). After entering
all characters, press
OK
.
●
The Confirmation screen appears.
●
If you make a mistake, press
w until the incorrect character
begins blinking. Then enter the correct character by pressing
rt.
C
Close the Confirmation screen.
Press
MENU
.
NOTE:
The characters available for the station name (ID) are A–Z, 0–9,
–,
f, +, I (space) (maximum of 4).
Fine-Tuning Channels Already Stored
A
Select the channel to fine-tune.
Press
rt
w
e
until the channel you want to tune begins
blinking.
B
Access the Manual Channel Set screen.
Press
OK
twice. The Manual Channel Set screen appears.
C
Perform tuning.
Press
e
until “+/–” begins blinking, then press
rt
until
the picture is its clearest. Then press
OK
.
●
The Confirmation screen appears.
●
Repeat steps
1
–
3
as necessary.
D
Close the Confirmation screen.
Press
MENU
.
Perform steps
1
and
2
of “Manual Channel Set” on page 54
to access the Confirmation screen before continuing.
Press
e
until the station name
(ID) begins blinking, then
press
rt
until the new
station’s name (ID) you want
to store begins blinking.
Registered station names
(
墌
pg. 57) appear as you
press
rt
.
Perform steps
1
and
2
of “Manual Channel Set” on page 54
to access the Confirmation screen and then perform step
1
and
2
of “Set Stations (A)” above before continuing.
Press
e
until the first letter of
the station name begins
blinking.
Perform steps
1
and
2
of “Manual Channel Set” on page 54
to access the Confirmation screen before continuing.
HRS7700EU3.fm Page 56 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
57
Filename [HRS7700EU3.fm]
Page 57March 8, 2000 1:58 pm
TV Station And ID List
*The “ID” abbreviation is what is shown on-screen in lieu of the station
name. The “ID” abbreviation is listed in the Confirmation screen and is
displayed on the TV screen when the recorder is tuned to a different
station.
ID* STATION NAME
1000
3SAT
ADLT
ANT3
ARD
ARTE
BBC
BBC1
BBC2
BR3
C+
C1
CAN5
CANV
CH4
CH5
CHLD
CINE
CLUB
CMT
CNN
CSUR
DISC
DR
DRS
DSF
ETB1
ETB2
EURO
EUSP
FEMM
FILM
FNET
FR2
FR3
GALA
HR3
INFO
ITA1
ITA7
ITV
JSTV
KA2
KAB1
KAN2
LOCA
M6
MBC
MCM
MDR
MOVE
MTV
MTV3
N3
N-TV
NBC
NDR3
NED1
NED2
NED3
NEWS
NICK
NRK
NRK2
ODE
ORF1
ORF2
TV1000
3SAT
ADULT
ANTENA3
ARD
ARTE
BBC GROUP
BBC1
BBC2
BAYERN3
CANAL PLUS
PORTUGUSES
CANALE5
KETNET CANVAS
CHANNEL4
CHANNEL5
CHILD
CINEMA
TELECLUB
CMT
CNN
ANDALUCIA
DISCOVERY
DR TV
DRS
DSF
ETB1
ETB2
EURONEWS
EUROSPORTS
FEMMAN
FILM
FILMNET
France2
France3
GALAVISION
HESSEN3
INFO-KANAL
ITALIA1
ITALIA7
ITV
JSTV
KA2
KABEL1
KANAL2
LOCAL
M6
MBR
MCM
MDR
MOVIE
MTV
MTV3
NORD3
N-TV
NBC SUPER
NDR3
NED1
NED2
NED3
NICKELODEON
NRK
NRK2
ODEON
ORF1
ORF2
ID* STATION NAME
ORF3
OWL3
PREM
PRO7
RAI1
RAI2
RAI3
RET4
21
RTBF
RTL
RTL2
RTL4
RTL5
RTP
S4
SAT1
SBS
SHOW
SIC
SKY
SKYN
SPRT
SRTL
STAR
SVT1
SVT2
SWR
TCC
TELE
TEL5
TF1
TM3
TMC
TNT
TRT
TSI
TSR
TV1
TV2
TV3
TV4
TV5
TV6
TVE1
TVE2
TVG
TVI
TVN
VCR
VERO
VH-1
VIVA
VIV2
VMTV
VOX
VT4
VTM
WDR1
WDR3
YLE1
YLE2
ZDF
ZTV
ORF3
OWL3
PREMIERE
PRO7
RAI1
RAI2
RAI3
RETE4
TELE21
RTBF1 or 2
RTL
RTL2
RTL4
RTL5
RTP
SCHWEIZ4
SAT1
SBS
SHOW
SOCIEDADE
SKY CHANNEL
SKY NEWS
SPORT
SUPER RTL
STAR-TV
SVT1
SVT2
SUEDWEST3
TCC
TELE
TELE5
TF1
TM3
TELEMONTECARLO
TNT INT
TRT INT
TSI
TSR
BRTN TV1
TV2
TV3
TV4
TV5
TV6
TVE1
TVE2
TV GALICIA
TV INDEPENDENT
TV NORGE
VIDEO
VERONICA
VH-1
VIVA
VIVA2
VIDEO MUSIC
VOX
VT4
VTM
West1
West3
YLE1
YLE2
ZDF
ZTV
HRS7700EU3.fm Page 57 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU3.fm]
Masterpage:Left
58
EN
Page 58March 8, 2000 1:58 pm
SUBSIDIARY SETTINGS (cont.)
Video Channel Set
Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the
RF cable.
If you have connected the recorder to your TV via the AV or S-VIDEO connection (
墌
pg. 8, 9), since you do not need
the video channel you have to set the video channel to off.
If you have connected the recorder to your TV via the RF connection (
墌
pg. 8), you have to set the correct video
channel.
A
Access the Video Channel Set mode.
Hold down
0
on the recorder until the front display
panel shows the following.
B
Set the RF output system.
The blinking number on the display indicates the RF
output system of your country.
●
If you have selected MAGYARORSZÁG (36),
C
ESKÁ
REPUBLIKA (42), POLSKA (48), РОССИЯ (07) or OTHER
EASTERN EUROPE (EE) for the country setting (
墌
pg. 10, 14),
press
rt to set to “2”.
●
For other countries, set to “1”. Then press
OK
.
(1: B/G 2: D/K)
C
Set the video channel.
With AV or S-VIDEO Connection
Press
PR –
until the front display panel shows “1OUT– –”
(or “2OUT– –”).
●
Now the video channel is set to off.
With RF Connection
Press
PR +
or
–
to set the video recorder to a vacant
channel between 22 and 69 which is not occupied by
any local station in your area.
(Example) If channel 50 is available in your area
Then set your TV to UHF channel 50.
●
If the two vertical white bars appear
clearly on the TV screen as shown to
the right, go to step
4
.
●
If the two vertical white bars do not
appear clearly, re-set the video
recorder to another vacant channel
and try again.
NOTES:
●
If you set the video recorder to a channel which is occupied by
a local station or has neighbouring channels that are occupied
by local stations, the picture reception quality will be affected
and some interference noise will appear on the TV screen. Be
sure to select a vacant channel which has no broadcast on
neighbouring channels.
●
If you cannot obtain the two vertical white bars clearly with
any channel between 22 and 69, consult your JVC dealer.
D
Exit the Video Channel Set mode.
Press
OK
on the remote control.
IMPORTANT
Perform the following steps only if —
— interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your
area.
— you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.
Before performing the following steps:
Make sure the recorder’s power is off and there is no cassette inserted in the recorder.
With AV or S-VIDEO Connection
To view picture signals from the video recorder, set
your TV to its AV mode.
With RF Connection
The channel on which the TV screen in step
3
appears
clearly is your video channel.
To view picture signals from the video recorder, set
your TV to the video channel.
HRS7700EU3.fm Page 58 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
59
Filename [HRS7700EU3.fm]
Page 59March 8, 2000 1:58 pm
S
HOW
V
IEW
®
Setup
Guide Program Number Set
A
Access the Main Menu screen.
Press
MENU
.
B
Access the Initial Set screen.
Press
rt
to move the highlight bar (pointer) to “INITIAL
SET”, then press
OK
or
e
.
C
Access the Guide Program Set screen.
Press
rt
to move the highlight bar (pointer) to “GUIDE
PROG SET”, then press
OK
or
e
.
D
Enter the Guide Program number.
Press
rt
to enter the Guide
Program number for the desired
station as shown in the TV
listings. Then press
OK
or
e
.
E
Enter the receiving channel position number.
Press the
NUMBER
key “
0
” to
select “TV PROG” or “SAT”.
Then press
rt
to input the
number of the recorder’s
channel position on which the
Guide Program number’s
broadcast is received by the
recorder or the satellite
receiver. Then press
OK
or
e
.
●
To timer-record a satellite
programme with the S
HOW
V
IEW
system, you need to install the provided Satellite Controller
and perform the procedure described in “Satellite Receiver
Control Setting” (
墌
pg. 15).
●
Repeat steps
4
and
5
as necessary.
F
Return to the normal screen.
Press
MENU
.
IMPORTANT
Normally, Auto Set Up (
墌
pg.10), Preset Download (
墌
pg. 12) or Auto Channel Set (
墌
pg. 52) sets the Guide Program numbers
automatically. You need to set the Guide Program numbers manually only in the following cases.
●
When timer-programming with the S
HOW
V
IEW
system, the channel position, where the station you wish to record is received on
your recorder, is not selected,
OR
when you add a channel after Auto Set Up, Preset Download or Auto Channel Set has taken place,
—Set the Guide Program number for that station manually.
●
When you wish to timer-record a satellite programme with the S
HOW
V
IEW
system,
—Set the Guide Program numbers for all satellite broadcasts received on your satellite receiver.
Turn on the TV and select the video channel (or
AV mode).
(Example)When inputting the
Guide Program
number 2 for ZDF.
Guide Program Number
“Guide Program (GUIDE PROG) number” refers to the
assigned TV station numbers, according to broadcast area,
for the S
HOW
V
IEW
timer recording. The Guide Program
numbers can be found in most TV listings.
(Example)If ZDF is received on
channel position 2.
HRS7700EU3.fm Page 59 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU3.fm]
Masterpage:Left
60
EN
Page 60March 8, 2000 1:58 pm
SUBSIDIARY SETTINGS (cont.)
Clock Set
A
Turn on the recorder.
Press
1
.
B
Access the Main Menu screen.
Press
MENU
.
C
Access the Initial Set screen.
Press
rt
to move the highlight bar (pointer) to “INITIAL
SET”, then press
OK
or
e
.
D
Access the Clock Set screen.
Press
rt
to move the highlight bar (pointer) to “CLOCK
SET”, then press
OK
or
e
. The Clock Set screen appears.
NOTE:
When you have selected MAGYARORSZÁG (36),
C
ESKÁ
REPUBLIKA (42), POLSKA (48), РОССИЯ (07) or OTHER
EASTERN EUROPE (EE) for the country setting (
墌
pg. 10, 14),
you cannot use Just Clock function. Skip steps
6
and
7
on
page 61.
Turn on the TV and select the video channel (or
AV mode).
Just Clock
The Just Clock function provides accurate time keeping
through automatic adjustments at regular intervals, by
reading data from a PDC signal.
The Just Clock option can be set “ON” or “OFF” at the Clock
Set screen (the default setting is “OFF”). Press
OK
until the
Just Clock setting begins blinking, then press
rt to change
the setting.
IMPORTANT:
If you turn off Just Clock, the accuracy of your
recorder’s built-in clock may be reduced, which could
adversely effect timer recording. We recommend you to keep
Just Clock on. In cases where the clock setting data from a
PDC signal is incorrect, however, you are advised to keep
Just Clock set to “OFF”.
IMPORTANT
If you performed Auto Set Up (
墌
pg. 10), Preset Download
(
墌
pg. 12) or Auto Channel Set (
墌
pg. 52), without ever
having set the clock previously, the recorder’s built-in clock is
also set automatically.
Perform the following steps only if —
—Auto Clock Set has not been performed correctly by Auto
Set Up, Preset Download or Auto Channel Set.
OR
—the recorder’s memory backup has expired.
OR
—you want to change Just Clock setting (
墌
“Just Clock” in
the left column).
HRS7700EU3.fm Page 60 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
61
Filename [HRS7700EU3.fm]
Page 61March 8, 2000 1:58 pm
E
Set the date and time.
Press
rt
to set the time, then press
OK
or
e
. The “DATE”
display begins blinking. Repeat the same procedure to set
the date and year.
●
When you set the time, press and hold
rt to change the time
by 30 minutes.
●
When you set the date, press and hold
rt to change the date
by 15 days.
F
Set Just Clock.
The default setting is “OFF”. Set as desired by pressing
rt
, then press
OK
or
e
.
●
For the Just clock function, refer to “Just Clock” on page 60.
●
If you set to “OFF”, you can disregard the next step as you
won’t be able to receive regular clock adjustments.
G
Set the source channel position for clock
data.
The recorder is preset to receive clock setting and
adjustment data from channel position 1.
Press
rt
to set the channel position to the number
representing the station transmitting clock setting data,
then press
OK
or
e
.
H
Start the clock operation.
Press
MENU
.
NOTES:
●
Just Clock (when set to “ON”) adjusts the recorder’s built-in
clock every hour, except for 23:00, 0:00, 1:00 and 2:00.
●
Just Clock is not effective when ...
... the recorder’s power is on.
... the recorder is in the Timer mode.
... a difference of more than 3 minutes exists between the
built-in clock’s time and the actual time.
... the recorder is in the Automatic Satellite Programme
Recording mode (
墌
pg. 34).
... the recorder is in the Power Save mode (
墌
pg. 50).
... ”L-2 SELECT” is set to “SAT” (
墌
pg. 37).
●
If Just Clock is set to “ON”, the recorder’s clock is
automatically adjusted at the start/end of Summer Time.
●
Just Clock may not function properly depending on the
reception condition.
HRS7700EU3.fm Page 61 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Left-FullCol
62
EN
Filename [HRS7700EU3.fm]
Page 62March 8, 2000 1:58 pm
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are
often easily corrected, and this can save you the trouble of sending your video recorder off for repair.
POWER
TAPE TRANSPORT
PLAYBACK
SYMPTOMPOSSIBLE CAUSECORRECTIVE ACTION
1.No power is supplied to the recorder.
●
The mains power cord is disconnected.Connect the mains power cord.
2.The clock is functioning properly, but
the recorder cannot be powered.
●
“
#” is displayed on the front display
panel with “AUTO TIMER” set to “OFF”.
Press the # button to turn the “#”
indicator off.
3.The remote control won’t function.
●
The batteries are discharged.Replace the dead batteries with new ones.
SYMPTOMPOSSIBLE CAUSECORRECTIVE ACTION
1.The tape does not run during
recording.
●
“
i
” is displayed on the front display
panel.
Press
4
to turn the “
i
” indicator off.
2.The tape will not rewind or fast-
forward.
●
The tape is already fully rewound or
fast-forwarded.
Check the cassette.
SYMPTOMPOSSIBLE CAUSECORRECTIVE ACTION
1.The playback picture does not appear
while the tape is running.
●
If you are using the RF connection,
. . . the TV receiver’s channel selector is
not set to the video channel.
. . . the recorder’s video channel has not
been correctly set.
If you are using the RF connection,
. . . set the TV receiver to the video
channel.
. . . perform “Video Channel Set”
(
墌
pg. 58).
●
If you are using the AV or S-VIDEO
connection, the TV receiver is not set to
the AV mode.
If you are using the AV or S-VIDEO
connection, set the TV to its AV mode.
2.Noise appears during visual search.
●
This is normal.
3.Noise appears during normal
playback.
●
The automatic tracking mode is
engaged.
Try manual tracking. (
墌
pg. 21)
4.The playback picture is blurred or
interrupted while TV broadcasts are
clear or “USE CLEANING CASSETTE”
message appears on the screen.
●
The video heads may be dirty.Use a dry cleaning cassette TCL-2UX or
consult your JVC dealer.
5.Breaks are noticeable in Hi-Fi
soundtrack.
●
The automatic tracking mode is
engaged.
Try manual tracking. (
墌
pg. 21)
HRS7700EU3.fm Page 62 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right-NoTitle0
EN
63
Filename [HRS7700EU3.fm]
Page 63March 8, 2000 1:58 pm
RECORDING
TIMER RECORDING
SYMPTOMPOSSIBLE CAUSECORRECTIVE ACTION
1.Recording cannot be started.
●
There is no cassette loaded, or the
cassette loaded has had its record safety
tab removed.
Insert a cassette, or using adhesive tape,
cover the hole where the tab was
removed.
2.TV broadcasts cannot be recorded.
●
“L-1”, “L-2”, “F-1”, “S-1” or “SAT” has
been selected as the input mode.
Set to the desired channel.
3.Tape-to-tape editing is not possible.
●
The source (another video recorder,
camcorder) has not been properly
connected.
Confirm that the source is properly
connected.
●
All necessary power switches have not
been turned on.
Confirm that all units’ power switches are
turned on.
●
The input mode is not correct.Set the input mode to “L-1”, “L-2”, “F-1”
or “S-1”.
4.Camcorder recording is not possible.
●
The camcorder has not been properly
connected.
Confirm that the camcorder is properly
connected.
●
The input mode is not correct.Set the input mode to “L-1”, “L-2”, “F-1”
or “S-1”.
SYMPTOMPOSSIBLE CAUSECORRECTIVE ACTION
1.Timer recording won’t work.
●
The clock and/or the timer have been set
incorrectly.
Re-perform the clock and/or timer
settings.
●
The timer is not engaged.Press
# and confirm that “#” is
displayed on the front display panel.
2.Timer programming is not possible.
●
Timer recording is in progress.Timer programming can’t be performed
while a timer recording is in progress.
Wait until it finishes.
3.“
#” and “[” on the front display
panel won’t stop blinking.
●
The timer is engaged but there’s no
cassette loaded.
Load a cassette with the record safety tab
intact, or cover the hole using adhesive
tape.
4.The cassette is automatically ejected,
and “
#” and “[” on the front
display panel won’t stop blinking.
●
The loaded cassette has had its record
safety tab removed.
Remove the cassette and cover the hole
with adhesive tape, or insert a cassette
with the record safety tab intact.
5.“
#” blinks for 10 seconds and the
Timer mode is disengaged.
●
# has been pressed when there are no
programs in memory, or the timer
record information has been
programmed incorrectly.
Check the programmed data and re-
program as necessary, then press
# again.
6.The cassette is automatically ejected,
the power shuts off and “
#” and
“
[” won’t stop blinking.
●
The end of the tape was reached during
timer recording.
The programme may not have been
recorded in its entirety. Next time make
sure you have enough time on the tape to
record the entire programme.
7.The S
HOW
V
IEW
system does not timer-
record properly.
●
The recorder’s channel positions have
been set incorrectly.
Refer to “Guide Program Number Set”
(
墌
pg. 59) and re-perform the procedure.
HRS7700EU3.fm Page 63 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Left-FullColx2
64
EN
Filename [HRS7700EU3.fm]
Page 64March 8, 2000 1:58 pm
TROUBLESHOOTING (cont.)
OTHER PROBLEMS
SYMPTOMPOSSIBLE CAUSECORRECTIVE ACTION
1.Whistling or howling is heard from the
TV during camcorder recording.
●
The camcorder’s microphone is too
close to the TV.
Position the camcorder so its microphone
is away from the TV.
●
The TV’s volume is too high.Turn the TV’s volume down.
2.When scanning channels, some of
them are skipped over.
●
Those channels have been designated to
be skipped.
If you need the skipped channels, restore
them (
墌
pg. 54).
3.The channel cannot be changed.
●
Recording is in progress.Press
9 to pause the recording, change
channels, then press
4 to resume
recording.
4.Channel settings that were made
manually seem to have changed or
disappeared.
●
After the manual settings were made,
Auto Channel Set was performed.
Perform manual setting again.
5.No channels are stored in the
recorder’s memory.
●
The TV aerial cable was not connected
to the recorder when Auto Set Up was
performed.
Turn off the recorder once and connect
the TV aerial cable to the recorder
properly, then turn on the recorder again.
The recorder will try Auto Set Up again
(
墌
pg. 10).
●
The fully-wired 21-pin SCART cable was
not connected between TV and the
recorder when Preset Download was
performed.
Turn off the recorder once and connect
the fully-wired 21-pin SCART cable to the
recorder properly, then turn on the
recorder again. Then perform Preset
Download again (
墌
pg. 12).
ATTENTION
This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch
the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After
checking the cassette, operate the unit as usual.
HRS7700EU3.fm Page 64 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Masterpage:Right
EN
65
Filename [HRS7700EU3.fm]
Page 65March 8, 2000 1:58 pm
QUESTIONS AND ANSWERS
PLAYBACK
Q.What happens if the end of the tape is reached
during playback or search?
A.
The tape is automatically rewound to the
beginning.
Q.During search, slow, still and frame-by-frame
playback, I can’t hear any audio. What’s the
problem?
A.
This is normal.
Q.Can the video recorder indefinitely remain in
the still mode?
A.
No. It stops automatically after 5 minutes to
protect the heads.
Q.When returning from variable-speed search to
normal playback, the picture is disturbed.
Should I be concerned about this?
A.
No, it is normal.
Q.Noise bar appear during variable-speed search.
What’s the problem?
A.
This is normal.
Q.Sometimes, during Index Search, the video
recorder can’t find the programme I want to
see. Why not?
A.
There may be index codes too close together.
RECORDING
Q.When I pause and then resume a recording, the
end of the recording before the pause is
overlapped by the beginning of the
continuation of recording. Why does this
happen?
A.
This is normal. It reduces distortion at the pause
and resume points.
Q.Can the video recorder indefinitely remain in
the Record-Pause mode?
A.
No. The video recorder goes to its Stop mode
automatically after 5 minutes to protect the
heads.
Q.What happens if the tape runs out during
recording?
A.
The video recorder automatically rewinds it to
the beginning.
TIMER RECORDING
Q. “
o
” and “
#
” remain lit on the front display
panel. Is there a problem?
A.
No. This is a normal condition for a timer
recording in progress.
Q.Can I programme the timer while I’m watching
a tape or a TV broadcast?
A.
You won’t see the picture as it is replaced by the
on-screen menu, but the audio from the
programme or tape you’re viewing can be
heard.
HRS7700EU3.fm Page 65 Wednesday, March 8, 2000 1:58 PM
Downloaded from www.Manualslib.commanuals search engine
Filename [HRS7700EU3.fm]
Masterpage:Left
66
EN
Page 66March 8, 2000 6:39 pm
SPECIFICATIONS
GENERAL
Power requirement:AC 220 V – 240 V
d
, 50 Hz/60 Hz
Power consumption
Power on:23 W
Power off:5.2 W
Temperature
Operating:5°C to 40°C
Storage:–20°C to 60°C
Operating position:Horizontal only
Dimensions (WxHxD)
:400 mm x 94 mm x 344 mm
Weight:4.1 kg
Format:S-VHS/VHS PAL standard
Maximum recording time
(SP):240 min. with E-240 video cassette
(LP):480 min. with E-240 video cassette
VIDEO/AUDIO
Signal system:PAL-type colour signal and CCIR
monochrome signal, 625 lines
50 fields
Recording system:DA4 (Double Azimuth) head helical
scan system
Signal-to-noise ratio: 45 dB
Horizontal resolution
:250 lines (VHS)
400 lines (S-VHS)
Frequency range:70 Hz to 10,000 Hz (Normal audio)
20 Hz to 20,000 Hz (Hi-Fi audio)
Input/Output:21-pin SCART connectors:
IN/OUT x 1, IN/DECODER x 1
RCA connectors:
VIDEO IN x 1, AUDIO IN x 1,
AUDIO OUT x 1
S-Video connectors:
IN x 1, OUT x 1
TUNER/TIMER
TV channel storage capacity
:99 positions (+AUX position)
Tuning system:Frequency synthesized tuner
Channel coverage:VHF 47 MHz – 89 MHz/
104 MHz – 300 MHz/
302 MHz – 470 MHz
UHF 470 MHz – 862 MHz
Aerial output:UHF channels 22 – 69 (Adjustable)
Memory backup time
:Approx. 60 min.
ACCESSORIES
Provided accessories
:RF cable,
Satellite Controller RM-SD1,
Infrared remote control unit,
“R6” battery x 2,
S-VHS ET labels
Specifications shown are for SP mode unless otherwise
specified.
E.& O.E. Design and specifications subject to change without
notice.
HRS7700EU3.fm Page 66 Wednesday, March 8, 2000 6:39 PM
Downloaded from www.Manualslib.commanuals search engine
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw JVC HR-S7700EU bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van JVC HR-S7700EU in de taal/talen: Engels als bijlage per email.
De handleiding is 3,63 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Stel vragen via chat aan uw handleiding
Stel uw vraag over deze PDF
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.