40755
26
Verklein
Vergroot
Pagina terug
1/33
Pagina verder
26
Confirm that the source is properly
connected.
Confirm that all units’ power switches
are turned on.
Set the input mode to “AU”.
Confirm that the camcorder is
properly connected.
Set the input mode to “AU”.
The source (another video recorder,
camcorder) has not been properly
connected.
All necessary power switches have
not been turned on.
The input mode is not correct.
The camcorder has not been
properly connected.
The input mode is not correct.
3. Tape-to-tape editing is not possible.
4. Camcorder recording is not
possible.
TIMER RECORDING
CORRECTIVE ACTION
Re-perform the clock and/or timer
settings.
Press TIMER and confirm that ““ is
displayed on the display panel.
Load a cassette with the Record
Safety tab intact, or cover the hole
using adhesive tape.
Remove the cassette and cover the
hole with adhesive tape, or insert a
cassette with the Record Safety tab
intact.
Check the programmed data and re-
program as necessary, then press
TIMER again.
The programme may not have been
recorded in its entirety. Next time
make sure you have enough time on
the tape to record the entire
programme.
Refer to "Guide Prog. Number Set"
and re-perform the procedure
( pg. 15).
SYMPTOM
1. Timer recording won’t work.
2. “ and “]“ on the display
panel won’t stop blinking.
3. The cassette is automatically
ejected, and ““ and “]“ on the
display panel won’t stop blinking.
4. “ blinks for 10 seconds and the
Timer mode is disengaged.
5. The cassette is automatically
ejected, the power shuts off and
“ and “]“ won’t stop
blinking.
6. ShowView does not timer-record
properly.
POSSIBLE CAUSE
The clock and/or the timer have
been set incorrectly.
The timer is not engaged.
The timer is engaged but there’s no
cassette loaded.
The loaded cassette has had its
Record Safety tab removed.
TIMER has been pressed when there
are no programs in memory, or the
timer record information has been
programmed incorrectly.
The end of the tape was reached
during timer recording.
The recorder’s channel positions
have been set incorrectly.
OTHER PROBLEMS
CORRECTIVE ACTION
Position the camcorder so its
microphone is away from the TV.
Turn the TV’s volume down.
If you need the skipped channels,
restore them ( pg. 22).
Press PAUSE to pause the recording,
change channels, then press PLAY to
resume recording.
Set the switch to TV.
Perform manual setting again.
SYMPTOM
1. Whistling or howling is heard from
the TV during camcorder record-
ing.
2. When scanning channels, some of
them are skipped over.
3. The channel cannot be changed.
4. The remote control won’t operate a
JVC TV.
5. Channel settings that were made
manually seem to have changed or
disappeared.
POSSIBLE CAUSE
The camcorders microphone is too
close to the TV.
The TV’s volume is too high.
Those channels have been desig-
nated to be skipped.
Recording is in progress.
The TV/VCR switch is in the wrong
position.
After the manual settings were
made, Auto Channel Set was
performed.
TROUBLESHOOTING (cont.)
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JVC HR-A233E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JVC HR-A233E in de taal/talen: Engels als bijlage per email.

De handleiding is 0,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info