Handleiding JVC GY-DV500 (pagina 60 van 96) (Engels)

34423

Verklein

Vergroot

Pagina terug

1/96

Pagina verder

10. S.S.F. (Super Scene Finder) FUNCTION

10-1 Explanation of the S.S.F. Function

During recording, the SSF function records the time code data at the point of time of a desired recorded scene in the unit's memory.

Using the S.S.F. data stored in memory during after-processing of the recorded image allows efficient use of the tape.

The S.S.F. function comprises the two modes CUE and MARK. Select the mode using the VCR Setup Menu item No. 398 S.S.F.

MODE.

When the VCR Setup Menu item No. 398 SSF MODE is set to CUE MODE or MARK MODE, the time code generator’s running

method is internally set to the REGEN mode.

When shooting in either of the modes, the time code data is stored in the unit's memory when the TAKE button on the front section

is pressed.

Ⅲ CUE Mode:

When the TAKE button is pressed at the desired scene during shooting of a given cut, the time code data at that point is stored

as CUE data in the unit's memory. The time code data at the time when recording is started or stopped with the VTR TRIGGER

button are stored in the unit's memory as scene data.

• In the MARK mode up to 119 scenes can be stored in memory. When the memory becomes full, the indication showing the

number of recorded scenes on the viewfinder screen becomes “M: - - -”.

However, if mixed with the CUE mode, the maximum number of scenes that can be stored decreases for each scene.

• In the CUE mode up to 237 points can be stored in memory.

However, for each REC start/stop the maximum number of points that can be stored decreases by two points for each scene.

The same is true when the CUE mode is mixed with the MARK mode.

• When recording in the S.S.F. mode, the reel number (cassette number) for each cassette is recorded in the memory of the

GY-DV500 and on tape.

• When the videocassette is replaced, new S.S.F. data is generated. S.S.F. data for six videocassettes can be stored in the

internal memory.

• Before recording the seventh cassette in the S.S.F. mode, be sure that necessary data has been transferred from the

memory to the non-linear editing controller or other component, or write data to the tape for each recording. See page 63.

Ⅲ MARK MODE

During shooting of a given cut, press the TAKE button at beginning of a desired scene and then press the TAKE button again at

the ending of the scene.

The time code data at the point where the TAKE button is pressed first becomes the start point of the scene and time code data

at the point where the TAKE button is pressed the second time becomes the ending point, and both are stored in the unit's

memory.

Shooting started

with VTR trigger

REC start REC pause

Scene

CUE 1

time code data

CUE 2

time code data

CUE 3

time code data

OUT

time code data

TAKE button TAKE button TAKE button

5 sec or more

Shooting started

with VTR trigger

REC start REC pause

Cut

time code data

OUT

time code data

OUT

time code data

IN time

code data

TAKE button TAKE button TAKE button TAKE button

Scene 1 Scene 2

Note:

• Leave an interval of at least 5 seconds between memorization of CUE data.

If the TAKE button is pressed within 5 seconds from the previous point, the new point is not memorized.

• In the CUE mode, time code log data stored on the camera memory may differ from the actual time code recorded on tape at

the time of pressing the TAKE button. This difference may be within 3 frames and it is not a malfunction.

Note:

• When recording is not performed in the S.S.F. mode, be sure to set the VCR SETUP MENU item No. 398 SSF MODE to OFF.

• Be sure to record S.S.F. data continuously on the same tape. It is not possible to rewind the tape for overwriting during the

recording.

If the tape is rewound in the middle of a recording, or after similar operation is performed, be sure to use the Scene End Cue

Up function in order to ensure that new data are recorded in continuation of the existing data.

☞ See “About the Scene End Cue Up Function” on page 63.

•

In the S.S.F. mode, the STBY/SAVE switch does not activate the VTR save mode. (The save mode is activated by a long pause.)

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

JVC GY-DV500 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info