Handleiding JVC GR-DX100 (pagina 43 van 60) (Engels)

39848

Verklein

Vergroot

Pagina terug

1/60

Pagina verder

USING THE REMOTE CONTROL UNIT

For More Accurate Editing

Some VCRs make the transition from Record-Pause to

Record mode faster than others. Even if you begin

editing for the camcorder and the VCR at exactly the

same time, you may lose scenes you wanted, or find

that you have recorded scenes you did not want. For a

cleanly edited tape, confirm and adjust the timing of the

camcorder against your VCR.

DIAGNOSING VCR/CAMCORDER TIMING

1 Play back the tape in the camcorder, then point the

remote control at the camcorder’s remote sensor and

press R.A.EDIT ON/OFF J.

The Random Assemble Editing Menu appears.

2 Perform Random Assemble Editing on Programme 1

only. In order to check VCR and camcorder timing,

select the beginning of a scene transition as your Edit-

In point.

3 Play back the dubbed scene.

• If any images from the scene prior to the transition

you chose for your Edit-In point were recorded, that

means your VCR moves too quickly from Record-

Pause to Record mode.

• If the scene you tried to dub starts in progress, the

VCR is slow to start recording.

ADJUSTMENT OF VCR/CAMCORDER TIMING

4 Point the remote control at the camcorder’s remote

sensor and press R.A.EDIT ON/OFF J to make the

Random Assemble Editing menu disappear, then press

MENU 4. The Menu Screen appears.

5 Press + or – 5 to select “ (VIDEO)” and press

SELECT/SET 3. Then, press + or – 5 to select

“SYNCHRO” and press SELECT/SET 3. The value for

“SYNCHRO” is highlighted.

6 Based on the diagnostics performed, you can now

advance the VCR’s record timing by pressing + 5. You

can also delay the VCR’s record timing by pressing –

5. The adjustment range is from –1.3 to +1.3 seconds,

in 0.1-second increments. Press SELECT/SET 3 to

finish the setting.

7 Press + or – 5 to to select “ RETURN” and press

SELECT/SET 3 twice.

Now perform Random Assemble Editing beginning with

step 4 on page 42.

NOTES:

● Before performing actual Random Assemble Editing, do a

few Random Assemble Editing trial runs to check whether

the value you have input is appropriate or not, and make

adjustments accordingly.

● Depending on the recorder, there may be situations

where the timing difference cannot be fully corrected.

Picture Wipe/Dissolve (GR-DX300/DX100 only)

(available only for Random Assemble Editing)

You can also use the fade/wipe effects on page 28.

DISSOLVE

The new scene gradually appears as the old one gradually

disappears.

WIPE — CORNER

The new scene wipes in over the previous one from the

upper right corner to the lower left corner.

WIPE — WINDOW

The next scene gradually wipes in from the centre of the

screen toward the corners, covering the previous scene.

WIPE — SLIDE

The next scene gradually wipes in over the previous one

from right to left.

WIPE — DOOR

The previous scene wipes out from the centre to the right

and left, like a door being pushed open to reveal the next

scene.

WIPE — SCROLL

The new scene wipes in over the last one from the bottom

of the screen to the top.

WIPE — SHUTTER

The new scene wipes in over the previous one from the

centre toward the top and bottom of the screen.

AUTOMATIC EDITING TO VCR

Rewind the tape in the camcorder to the beginning

of the scene you want to edit and press PAUSE (6) H.

Point the remote control towards the VCR’s remote

sensor and press VCR REC STBY (q6) K, or

manually engage the VCR’s Record-Pause mode.

Press START/STOP k on the remote control.

Editing proceeds as programmed, right through to the

end of the last registered scene.

• When dubbing is complete, the camcorder enters the

Pause mode, and the VCR enters its Record-Pause

mode.

• If you do not register an Edit-Out point, the tape will

be dubbed all the way to the end automatically.

• If you operate the camcorder during automatic editing,

the VCR will enter its Record-Pause mode and

automatic editing will stop.

Engage the Stop modes for the camcorder and the

VCR.

To make the R.A.Edit counter display disappear, press

R.A.EDIT ON/OFF J on the remote control.

NOTES:

● Pressing R.A.EDIT ON/OFF J on the remote control

clears all settings registered during Random Assemble

Editing.

● When the editing cable is connected to the remote

control’s Pause In connector during dubbing, make sure

the remote control is pointed at the VCR’s sensor, and

the path between the two is unobstructed.

● Random Assemble Editing may not function properly

when using a tape including several duplicated time

codes (

੬ pg. 14).

01 DX300/100/95/75EK_EN 35-44 2/26/03, 7:13 PM43

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

JVC GR-DX100 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van JVC GR-DX100

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info