Handleiding JVC DLA-RS600E (pagina 20 van 80) (Engels)

660659

Verklein

Vergroot

Pagina terug

1/80

Pagina verder

D-ILA

PROJECTOR

DLA-RS600

DLA-RS500

DLA-RS400

http://manual3.jvckenwood.com/projector/mobile/global/

The Mobile User Guide can be viewed on mobile internet devices including

smartphones and tablets.

Mobile User Guide

Pour utilisation par le client :

Entrerci-dessous le N°de série qui

est situé sous le boîtier. Garder

cetteinformation comme référence

pour le futur.

Instrucción para el cliente :

Introduzca a continuación el nº de

serie que aparece en la parte

inferior lateral de la caja. Conserve

esta información como referencia

para uso ulterior.

For Customer use :

Enter below the serial No. which is

located on the side of the cabinet.

Retain this information for future

reference.

DLA-RS600U /DLA-RS500U /

DLA-RS400U

DLA-RS600U /DLA-RS500U /

DLA-RS400U

DLA-RS600U /DLA-RS500U /

DLA-RS400U

Model No.

Serial No.

N° de modèle

N° de série

Modelo Nº

Nº de serie

Not suitable for household room illumination.

INSTRUCTIONS

B5A-1144-0D

Getting Started Set up Operate Adjust/Set Maintenance Troubleshooting Others

Safety Precautions

IMPORTANT INFORMATION

This product has a High Intensity

Dis-charge (HID) lamp that contains

mercury. Manage in accord with

disposal laws.

Disposal of these materials may be

regulated in your community due to

environmental considerations. For

disposal or recycling information,

please contact your local authorities or

for USA, the Electronic Industries

Alliance: http://www.eiae.org. or call

1-800-252-5722(For USA)

or 1-800-964-2650(For Canada).

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

FCC INFORMATION (U.S.A. only)

CAUTION:

Changes or modification not approved by JVC could

void the user’s authority to operate the equipment.

About the installation place

Do not install the projector in a place that cannot

support its weight securely.

If the installation place is not sturdy enough, the

projector could fall or overturn, possibly causing

personal injury.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment

and receiver.

Consult the dealer or an experienced radio/TV

technician for help.

Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

NOTE:

This equipment has been tested and found to comply

with the limits for Class B digital devices, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protec tion against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruc tions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encourage to try to

correct the interference by one or more of the

following measures:

WARNING:

THIS APPARATUS MUST BE EARTHED.

CAUTION:

To reduce the risk of electric shock, do not remove

cover. Refer servicing to qualified service personnel.

This projector is equipped with a 3-blade grounding

type plug to satisfy FCC rule. If you are unable to

insert the plug into the outlet, contact your electrician.

⹣晼㯡婌♟㒷

For the customers in Taiwan only

NOISE EMISSION DECLARATION

The sound pressure level at the operator position is

equal or less than 30dB(A) according to ISO7779.

Model Number: DLA-RS600BU, DLA-RS500BU,

DLA-RS400BU

Trade Name: JVC

Responsible party: JVCKENWOOD USA Corporation

Address: 1700 Valley Road Wayne, N. J. 07470

Telephone Number: 973-317-5000

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

Declaration of Conformity

Getting Started

PORTABLE CART WARNING

(symbol provided by RETAC)

S3126A

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions.

This unit has been engineered and manufactured to

assure your personal safety. But IMPROPER USE

CAN RESULT IN POTENTIAL ELECTRICAL

SHOCK OR FIRE HAZARD. In order not to defeat

the safeguards incorporated into this product,

observe the following basic rules for its installation,

use and service. Please read these Important

Safeguards carefully before use.

All the safety and operating instructions should be read

before the product is operated.

The safety and operating instructions should be retained for

future reference.

All warnings on the product and in the operating

instructions should be adhered to.

All operating instructions should be followed.

Place the projector near a wall outlet where the plug can be

easily unplugged.

Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

Do not use attachments not recommended by the product

manufacturer as they may be hazardous.

Do not use this product near water. Do not use immediately

after moving from a low temperature to high temperature,

as this causes condensation, which may result in fire,

electric shock, or other hazards.

Do not place this product on an unstable cart, stand, or

table. The product may fall, causing serious injury to a child

or adult, and serious damage to the product. The product

should be mounted according to the manufacturer’s

instructions, and should use a mount recommended by the

manufacturer.

When the product is used on a cart,

care should be taken to avoid quick

stops, excessive force, and uneven

surfaces which may cause the product

and cart to overturn, damaging

equipment or causing possible injury to

the operator.

Slots and openings in the cabinet are provided for

ventilation. These ensure reliable operation of the product

and protect it from overheating. These openings must not

be blocked or covered. (The openings should never be

blocked by placing the product on bed, sofa, rug, or similar

surface. It should not be placed in a built-in installation such

as a bookcase or rack unless proper ventilation is provided

and the manufacturer’s instructions have been adhered to.)

To allow better heat dissipation, keep a clearance between

this unit and its surrounding as shown below. When this unit

is enclosed in a space of dimensions as shown below, use

an air-conditioner so that the internal and external

temperatures are the same. Overheating can cause

damage.

When the power supply cord or plug is damaged.

If liquid has been spilled, or objects have fallen on the

product.

If the product has been exposed to rain or water.

If the product does not operate normally by following the

operating instructions. Adjust only those controls that

are covered by the Operation Manual, as an improper

adjustment of controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to normal operation.

If the product has been dropped or damaged in any

way.

When the product exhibits a distinct change in

performance, this indicates a need for service.

When replacement parts are required, be sure the service

technician has used replacement parts specified by the

manufacturer or with same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

The product should be placed more than one foot away

from heat sources such as radiators, heat registers, stoves,

and other products (including amplifiers) that produce heat.

When connecting other products such as VCR’s, and DVD

players, you should turn off the power of this product for

protection against electric shock.

Power source indicated on the label. If you are not sure of

the type of power supply to your home, consult your

product dealer or local power company.

This product is equipped with a three-wire plug. This plug

will fit only into a grounded power outlet. If you are unable

to insert the plug into the outlet, contact your electrician to

install the proper outlet. Do not defeat the safety purpose of

the grounded plug.

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them. Pay particular attention to cords at doors,

plugs, receptacles, and the point where they exit from the

product.

For added protection of this product during a lightning

storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet and

disconnect the cable system. This will prevent damage to

the product due to lightning and power line surges.

Do not overload wall outlets, extension cords, or

convenience receptacles on other equipment as this can

result in a risk of fire or electric shock.

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltages

and other hazards. Refer all service to qualified service

personnel.

Unplug this product from the wall outlet and refer service to

qualified service personnel under the following conditions:

Getting Started

Do not place combustibles behind the cooling fan. For

example, cloth, paper, matches, aerosol cans or gas

lighters that present special hazards when over heated.

Do not look into the projection lens while the illumination

lamp is turned on. Exposure of your eyes to the strong light

can result in impaired eyesight.

Do not look into the inside of this unit through vents

(ventilation holes), etc. Do not look at the illumination lamp

directly by opening the cabinet while the illumination lamp is

turned on. The illumination lamp also contains ultraviolet

rays and the light is so powerful that your eyesight can be

impaired.

Do not drop, hit, or damage the light-source lamp (lamp

unit) in any way. It may cause the light-source lamp to

break and lead to injuries. Do not use a damaged light

source lamp. If the light-source lamp is broken, ask your

dealer to repair it. Fragments from a broken light-source

lamp may cause injuries.

The light-source lamp used in this projector is a high

pressure mercury lamp. Be careful when disposing of the

light-source lamp. If anything is unclear, please consult

your dealer.

Do not ceiling-mount the projector to a place which tends to

vibrate; otherwise, the attaching fixture of the projector

could be broken by the vibration, possibly causing it to fall

or overturn, which could lead to personal injury.

Use only the accessory cord designed for this product to

prevent shock.

For health reasons, please take a break of about 5-15

minutes every 30-60 minutes and let your eyes rest. Please

refrain from watching any 3D-images when you feel tired,

unwell or if you feel any other discomfort. Moreover, in case

you see a double image, please adjust the equipment and

software for proper display. Please stop using the unit if the

double image is still visible after adjustment.

Once every three years, please perform an internal test.

This unit is provided with replacement parts needed to

maintain its function (such as cooling fans). Estimated

replacement time of parts can vary greatly depending on

frequency of use and the respective environment. For

replacement, please consult your dealer, or the nearest

authorized JVC service center.

When fixing the unit to the ceiling, Please note that we do

not take any responsibility, even during the warranty period,

if the product is damaged due to use of metal fixtures used

for fixation to the ceiling other than our own or if the

installation environment of said metal fixtures is not

appropriate. If the unit is suspended from the ceiling during

use, please be careful in regard to the ambient temperature

of the unit. If you use a central heating, the temperature

close to the ceiling will be higher than normally expected.

Video images can burn into the electronic com ponent

parts. Please do not display screens with still images of

high brightness or high contrast, such as found in video

games and computer programs. Over a long period of time

it might stick to the picture element. There is no problem

with the playback of moving images, e.g. normal video

footage.

Video images can burn into the electronic com ponent

parts. Please do not display screens with still images of

high brightness or high contrast, such as found in video

games and computer programs. Over a long period of time

it might stick to the picture element. There is no problem

with the playback of moving images, e.g. normal video

footage.

Not using the unit for a long time can lead to malfunction.

Please power it on and let it run occasionally. Please avoid

using the unit in a room where cigarettes are smoked. It is

impos sible to clean optical component parts if they are

contaminated by nicotine or tar. This might lead to

performance degradation.

Please watch from a distance three times the height of the

projected image size. Persons with photosensitivity, any

kind of heart disease, or weak health should not use 3D

glasses.

Watching 3D-images might be cause of illness. If you feel

any change in your physical condition, please stop

watching immediately and consult a physician if necessary.

When watching 3D images, it is recommended to take

regular breaks. As the length and frequency of the required

breaks differ for every person, please judge according to

your own condition.

If your child watches while wearing 3D glasses, it should be

accompanied by its parents or an adult guardian. The adult

guardian should be careful to avoid situations where the

child’s eyes might become tired, as responses to tiredness

and discomfort, etc., are hard to detect, and it is possible

for the physical condition to deteriorate very quickly. As the

visual sense is not yet fully developed in children under the

age of 6, please consult a physician in regard to any

problem concerning 3D-images if necessary.

Note that when using the 3D feature, the video output may

appear different from the original video image due to image

conversion on the device.

* DO NOT allow any unqualified person to

install the unit.

Be sure to ask your dealer to install the unit

(e.g.attaching it to the ceiling) since special

technical knowledge and skills are required for

installation. If installation is performed by an

unqualified person, it may cause personal injury or

electrical shock.

Getting Started

Power cord

For European continent

countries

For United Kingdom

Green-and-yellow

Blue

Brown

Fuse

: Earth

: Neutral

: Live

POWER CONNECTION

WARNING:

Do not cut off the main plug from this

equipment.

The power supply voltage rating of this product is

AC100V – AC240V. Use only the power cord

designated by our dealer to ensure Safety and EMC.

Ensure that the power cable used for the projector is

the correct type for the AC outlet in your country.

Consult your product dealer.

If the plug fitted is not suitable for the power points

in your home or the cable is too short to reach a

power point, then obtain an appropriate safety

approved extension lead or adapter or consult your

dealer. If nonetheless the mains plug is cut off,

dispose of the plug immediately, to avoid a possible

shock hazard by inadvertent connection to the main

supply. If a new main plug has to be fitted, then

follow the instruction given below.

Dear Customer,

This apparatus is in conformance with the valid

European directives and standards regarding

electromagnetic compatibility and electrical safety.

European representative of

JVC KENWOOD Corporation is:

JVC Technical Services Europe GmbH

Konrad-Adenauer-Allee 1-11

61118 Bad Vilbel

Germany

INFORMATION Manufacturer:

JVC KENWOOD Corporation

3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,

Kanagawa, 221-0022, JAPAN

Importer (EU only):

JVC KENWOOD U.K. Limited

12 Priestley Way, London, NW2 7BA

UNITED KINGDOM

For more details, please refer to our website.

http://www.jvc.net/

THIS APPARATUS MUST BE EARTHED.

IMPORTANT (Europe only):

The wires in the mains lead on this product are

colored Vert et jaune in accordance with the

following cord:

IMPORTANT (Europe only):

POWER CONNECTION

(United Kingdom only)

When replacing the fuse, be sure to use only a

correctly rated approved type, re-fit the fuse cover.

IF IN DOUBT —— CONSULT A COMPETENT

ELECTRICIAN.

Open the fuse compartment with the blade

screwdriver, and replace the fuse.

(* An example is shown in the illustration below.)

As these colors may not correspond with the

colored making identifying the terminals in your

plug, proceed as follows:

The wire which is colored green-and-yellow must be

connected to the terminal which is marked M with

the letter E or the safety earth or colored green or

green-and-yellow. The wire which is colored blue

must be connected to the terminal which is marked

with the letter N or colored black.

The wire which is colored brown must be connected

to the terminal which is marked with the letter L or

colored red.

For USA and Canada only

Use only the following power cord.

Getting Started

ENGLISH

Information for Users on Disposal of Old Equipment and Batteries

[European Union only]

These symbols indicate that equipment with these symbols should not be disposed

of as general household waste. If you want to dispose of the product or battery,

please consider the collection systems or facilities for appropriate recycling.

Notice:

The sign Pb below the symbol for batteries indicates that this battery contains lead.

Benutzerinformationen zur Entsorgung alter Geräte und Batterien

[Nur Europäische Union]

Diese Symbole zeigen an, dass derartig gekennzeichnete Geräte nicht als normaler

Haushaltsabfall entsorgt werden dürfen. Wenden Sie sich zur Entsorgung des

Produkts oder der Batterie an die hierfür vorgesehenen Sammelstellen oder

Einrichtungen, damit eine fachgerechte Wiederverwertung möglich ist.

Hinweis:

Notification:

Das Zeichen Pb unterhalb des Batteriesymbols gibt an, dass diese

Batterie Blei enthält.

Informations relatives à l’élimination des appareils et des piles usagés, à l’intention des utilisateurs

[Union européenne seulement]

Si ces symboles figurent sur les produits, cela signifie qu’ils ne doivent pas être jetés

comme déchets ménagers. Si vous voulez jeter ce produit ou cette pile, veuillez

considérer le système de collecte des déchets ou les centres de recyclage appropriés.

La symbole Pb en dessous du symbole des piles indique que cette

pile contient du plomb.

Informatie voor gebruikers over het verwijderen van oude apparatuur en batterijen

[Alleen Europese Unie]

Deze symbolen geven aan dat appara tuur met dit symbool niet mag worden

weggegooid als algemeen huishoudelijk afval. Als u h

et product of de batterij wilt

weggooien, kun t u inzamelsystemen of faciliteiten voor een geschikte recycling

gebruiken.

Opmerking:

Het teken Pb onder het batterijsymboo l geeft aan dat deze batterij lood bevat.

Battery

Products

Batterie

Produkte

Pile

Produits

Batterij

Producten

DEUTSCH

FRANÇAIS

NEDERLANDS

Información para los usuarios sobre la eliminación de baterías/pilas usadas

[Sólo Unión Europea]

Estos símbolos indican que el equipo con estos símbolos no debe desecharse

con la basura doméstica. Si desea desechar el producto o batería/pila, acuda

a los sistemas o centros de recogida para que los reciclen debidamente.

Atención: La indicación Pb debajo del símbolo de batería/pila indica que ésta

contiene plomo.

Baterías/pilas

Productos

ESPAÑOL / CASTELLANO

ITALIANO

Informazioni per gli utenti sullo smaltimento delle apparecchiature e batterie obsolete

[Solo per l’Unione Europea]

Questi simboli indicano che le apparecchiature a cui sono relativi non devono

essere smaltite tra i rifiuti domestici generici. Se si desidera smaltire questo

prodotto o questa batteria, prendere in considerazione i sistem i o le strutture di

raccolta appropriati per il riciclaggio corretto.

Nota:

Il simbolo Pb sotto il simbolo delle batter ie indica che questa batteria contiene piombo.

Batteria

Prodotti

Getting Started

As with any bright light source, do not stare into the

beam, RG2 IEC 62471-5:2015

Location information of the labels

Getting Started

Contents

Getting Started

Safety Precautions

.................................................. 2

Accessories/Optional Accessories .......................... 9

Check the Accessories ........................................ 9

Optional Accessories ........................................... 9

Controls and Features ........................................... 10

Main Unit - Front ................................................ 10

Main Unit - Bottom ............................................. 10

Main Unit - Rear ................................................. 11

Main Unit - Input Terminals ................................ 12

Remote Control ................................................. 13

Loading Batteries into the Remote Control ........ 14

Effective Range of Remote Control Unit ............ 14

Set up

Installing the Projector ........................................... 15

Precautions during Installation ........................... 15

Precautions during Mounting ............................. 16

Adjusting the Position ........................................ 17

Connecting the Projector ....................................... 18

Connecting to the HDMI Input Terminal (Digital

Input) ................................................................. 18

Connecting to the LAN Terminal ........................ 19

Connecting to the RS-232C Terminal ................ 19

Connecting to the TRIGGER Terminal ............... 20

Connecting the Power Cord (Supplied Accessory)

...... 20

Operate

Viewing Videos ...................................................... 21

Adjusting the Projector Screen .............................. 23

Adjusting the Lens According to the Projection

Position .............................................................. 23

Saving and Retrieving Adjustment Settings ....... 24

Setting Screen Correction .................................. 26

Adjusting the Screen Size (Aspect) ................... 27

Viewing 3D Movies ................................................ 28

Installing the 3D SYNCHRO EMITTER .............. 28

Viewing 3D Movies ............................................ 29

Adjusting 3D Movies .......................................... 29

Adjust/Set

Selecting an Image Quality According to the Video

Type ...................................................................... 30

Setting the Picture Mode ................................... 30

Setting the Color Profile ..................................... 31

Adjusting to the Preferred Color (Color

Management) .................................................... 33

Adjusting Movies for Increased Expressiveness

(Multiple Pixel Control) .......................................... 34

Fine-tuning the Image Quality ............................... 36

Adjusting the Output Value of the Projected Image

(Gamma)

........................................................... 36

Fine-tuning to the Preferred Gamma Setting ..... 37

Reducing the After-image of Fast-moving Images

(Blur Reduction) ................................................. 39

Viewing High Contrast Images (Lens Aperture) . 40

Adjustments and Settings in the Menu .................. 41

List of Menu Items ............................................. 41

Picture Adjust .................................................... 43

Input Signal ........................................................ 46

Installation ......................................................... 48

Display Setup .................................................... 54

Function ............................................................. 54

Information ......................................................... 56

Maintenance

Replacing the Lamp .............................................. 57

Lamp Replacement Procedure .......................... 57

Resetting the Lamp Time ................................... 59

Maintaining the Cabinet and Remote Control ........ 59

Cleaning and Replacing the Filter ......................... 60

Troubleshooting

Troubleshooting .................................................... 61

When the following messages appear... ................ 65

Others

External Control .................................................... 66

RS-232C Specifications ..................................... 66

TCP/IP Connection ............................................ 66

Command Format .............................................. 67

Remote Control Code ........................................ 68

Communications Example ................................. 69

Specifications ........................................................ 70

Index ..................................................................... 77

Symbols used in this manual

indicates a function that is supported by DLA-RS600.

indicates a function that is supported by DLA-RS500.

indicates a function that is supported by DLA-RS400.

Items not marked with any of the above symbols are

supported by all models.

Getting Started

Accessories/Optional Accessories

Check the Accessories

Lens cover 9 ....................................................................

1 piece

* It is attached to the main unit at the time of shipment.

Remote control ....................................................................... 1 piece

AAA-size batteries (for operational check) ............................ 2 pieces

Power cord (for USA) (about. 2 m) ......................................... 1 piece

Power cord (for UK) (about. 2 m) ............................................ 1 piece

Power cord (for EU) (about. 2 m) ............................................ 1 piece

Quick User Guide, safety precautions, warranty card, and other printed material are also included.

Be sure to read the “Safety Precautions” before using this projector.

Optional Accessories

Replacement lamp: product no. PK-L2615U

3D GLASSES: model PK-AG3

3D SYNCHRO EMITTER: model PK-EM2

Compatibility Chart for 3D SYNCHRO EMITTER and 3D GLASSES

3D GLASSES

PK-AG1 *

(Communication

Method: IR (Infrared))

PK-AG2 *

(Communication

Method: IR (Infrared))

PK-AG3

(Communication

Method: RF (Radio

frequency))

3D SYNCHRO EMITTER PK-EM1 *

(Communication

Method: IR (Infrared))

X X —

PK-EM2

(Communication

Method: RF (Radio

frequency))

— — X

* Discontinued product

Please check with your authorized dealer for details.

Getting Started

Controls and Features

Main Unit - Front

ABC

Lens

This is a projection lens. Do not look through the lens

while an image is projected.

Lens cover 7 8

The lens cover opens/closes when the power supply

is turned on/off. (

P. 48)

For 9, attach the lens cover when the unit is not

in use.

Remote Sensor (front)

Please

aim the remote control at this area when using

it.

* There is also a remote sensor at the rear.

Indicator

Refer to “Indicator Display on the Main Unit”P.

74.

Exhaust vent

Warm air is discharged to cool down the internal

temperature.

Do not block the vents.

Main Unit - Bottom

Inlets (at 3 points on the rear/bottom)

The inlets take in air to cool down the internal temperature.

Do not block or prevent the outflow of hot air. Doing so may cause

the unit to malfunction.

* There

are two inlets on the right and left sides at the rear of the unit.

Manual button for lens cover 7 8

The lens cover can be opened when pressed down.

It is used for maintenance purposes. You can also make use of it

when you need to open the lens cover urgently.

Feet

The height and angle of the projector can be adjusted by turning the

foot. (0 to 5 mm) (P. 17)

When the foot is removed, it can be used as the mounting holes for

the ceiling mount bracket.

Getting Started

Main Unit - Rear

IKLM

Input terminals

In addition to the video input terminal, there are also

other connection terminals for devices such as

controllers and optional equipment.

Please see

“Main Unit - Input Terminals”P. 12 for

more details about the terminals.

Lamp cover

When replacing the light source lamp, remove this

cover.

Operation panel

For more details, please refer to the “Operation

panel” in the diagram below.

Remote Sensor (rear)

Please

aim the remote control at this area when using

it.

* There is also a remote sensor at the front.

Power input terminal

Connect the supplied power cord to this terminal.

Operation panel

[MENU]: Displays the menu

[BACK]: Returns to the previous menu

[JKH I] keys: Selects an item

[OK]: Confirms a selection

[INPUT]: Switches the input

A [STANDBY/ON]: Turns “on”/“off” the

power

Getting Started

Main Unit - Input Terminals

A B C

Enlarged View of Rear Face

[HDMI 1] input terminal

[HDMI 2] input terminal

For connecting to devices that support HDMI output.

(P.

18)

It is fitted to the M3 lock hole. The depth of the screw

hole is 3 mm.

[LAN] terminal (RJ-45)

The projector can be controlled by connecting it to a

PC through the computer network for control

commands to be sent to the projector.

[RS-232C] terminal (D-sub 9-pin

male)

The projector can be controlled by connecting a PC to

this terminal.

[3D SYNCHRO] terminal

By connecting a 3D SYNCHRO EMITTER (sold

separately) to this terminal, you can view 3D movies.

[TRIGGER] terminal (E)

Output

terminal for DC 12 V, 100 mA power supply. It

is used for sending output signals to control devices

such as an elevating screen that is equipped with a

trigger function.

Note that improper connection may damage the

projector. (Tip=DC +12 V, Sleeve=GND)

Getting Started

Remote Control

B [STAND BY]

Turns off the power. (

P. 22)

C [ON]

Turns on the power. (P. 21)

[INPUT]

Select an input from [HDMI 1]

and [HDMI 2]. (P. 21)

[INFO.]

Displays the information menu.

(P. 56)

[MEMORY MENU]

Switches between saving,

retrieving, and editing of the lens

memory. (P. 24)

[MEMORY 1]

Retrieves LENS MEMORY 1.

[MEMORY 2]

Retrieves LENS MEMORY 2.

[LENS CONTROL]

For adjusting focus, zoom, and

shift. (P. 23)

[LENS AP.]

For setting the lens aperture.

(P. 40)

[C.M.D.]

For setting frame interpolation.

(P. 39)

[HIDE]

Hides the image temporarily.

(P. 21)

[LIGHT]

Illuminates the buttons on the

remote control.

[JKH I] keys

For selecting an item.

[OK]

Confirms a selected item.

[MENU]

Displays the menu,

or hides the menu if it is

displayed.

[BACK]

Returns to the previous menu.

[PICTURE MODE]

Switches the Picture mode to

[FILM]*1, [CINEMA], [ANIME.],

[NATURAL], [THX]*1, or

[USER]*2. (

P. 30)

*1 7 8 only

*2 [USER1], [USER2] and

[USER3] are available for

[ADVANCED MENU]

Pressing the button each time

switches the menu in the

following sequence: “Picture

Mode” " “Color Profile” "

“Color Temp.” " “Gamma”

[MPC]

For setting the MPC level.

(P. 34)

[P.ANALYZER]

Turns on/off the analysis

screen. (P. 35)

[GAMMA]

For setting the gamma level.

(P. 36)

[COLOR TEMP.]

For setting the color

temperature. (P. 44)

[3D FORMAT]

Switches the 3D format.

(P. 29)

[PIC. ADJ.]

Switches the items for adjusting

the image quality, such as

contrast, brightness, etc.

(P. 45)

HDMI 1

INPUT

LENS MEMORY

PICTURE MODE

HDMI 2 INFO.

FILM CINEMA ANIME.

NATURAL

THX USER

MEMORY

MEMORY1 MEMORY2

ADVANCED

FORMAT

PIC.

ADJ.

COLOR

TEMP.

GAMMA

P.ANALYZER

MPC

LENS

CONTROL

LENS AP.

C.M.D.

PICTURE MODE

CINEMA ANIME.

NATURAL

USER1 USER2 USER3

Getting Started

Loading Batteries into the Remote Control

Loading the batteries

Removing the batteries

If the remote control has to be brought closer to the

projector to operate, it means that the batteries are

wearing out. Replace the batteries with new ones

(AAA).

Insert the batteries according to the t s marks.

Be sure to insert the s end first.

When removing the battery, do so from the t end.

If an error occurs while using the remote control,

remove the batteries and wait for five minutes. Load

the batteries again and operate the remote control.

CAUTION

Do not put the remote control in a place with an

exposure to direct sun light or high temperature.

It may deformed due to heat, or the internal

components may be adversely affected resulting in

fire hazard.

Remove the batteries from the remote control when

storing the remote control.

Storing the remote control for a prolonged period

without removing the batteries can cause battery

leakage.

Effective Range of Remote Control Unit

When aiming the remote control toward the sensor on this

unit

(front or rear), ensure that the distance to the sensor

is within 7 m.

If the remote control fails to work properly, move closer

to this unit.

30°

20°

Remote Control

This unit

Control through reflection off a screen, etc.

Ensure that the total of distance A (between this unit and

the screen) and distance B (between the remote control

and the screen) is within 7 m.

As the efficiency of signals reflected from the remote

control unit varies with the type of screen used, the

operable distance may decrease.

30°

20°

Screen

Remote Control

This unit

CAUTION

Do not put the remote control in a place with an exposure to direct sun light or high temperature.

It may deformed due to heat, or the internal components may be adversely affected resulting in fire hazard.

Remove the batteries from the remote control when storing the remote control.

Storing the remote control for a prolonged period without removing the batteries can cause battery leakage.

Getting Started

Installing the Projector

Precautions during Installation

Please read the following carefully before installing this

unit.

Do not install at the following

This unit is a precision device. Please refrain from

installing

or using it at the following locations. Otherwise,

it may cause fire or malfunction.

Dusty, wet and humid places

Places subject to oily smoke or cigarette smoke

On top of a carpet or bedding, or other soft surfaces

Places exposed to direct sunlight

Places with a high or low temperature

Do not install this unit in a room that is oily or subject

cigarette smoke. Even a small quantity of smoke or

oiliness can have a long-term impact on this unit.

* This unit produces a great amount of heat, and is

designed to take in cool air to cool its optical

components. Using the unit at the above locations

may cause dirt to attach to the light path, thereby

resulting in dark images or dull colors.

Dirt that sticks to the optical components cannot be

removed.

Maintain clearance from the wall, etc.

As the unit discharges a large amount of heat, install it

with adequate clearance from the surroundings as shown

below.

Front

150 mm

and above

200 mm

and above

300 mm

and above

300 mm

and above

150 mm and above

Leave the front area of the unit unblocked.

If there is any obstructing object in front of the exhaust

vent, hot air will flow back to the unit and cause it to heat

up. Hot air flowing out of the unit may cast shadows on

the screen (heat haze phenomenon).

Using the projector

This

unit uses a projection lamp, which will heat up when

in use.

Please refrain from projecting in the following

circumstances. Otherwise, it may cause fire or

malfunction.

Projection with the unit stood vertically

Projection with the unit inclined at an angle

Horizontal inclination: within ± 5 °

5° 5°

Vertical inclination: within ± 15 °

15°

Malfunction

may occur if the angle is not set within the

abovementioned range.

Installing the screen

Install the unit and the screen such that they are

perpendicular to each other.

Screen

Front

Please choose a screen material with non-uniform

patterns.

Uniform patterns such as checks may cause

interference patterns to occur.

this case, you can change the size of the screen to

make the interference patterns less noticeable.

Using the projector at a high altitude

When using this unit at a location that is higher than 900

m above sea level (low air pressure), set the “High

Altitude Mode” to “On”. (P.

50)

Set up

Precautions during Mounting

Securing (mounting) the projector

When

this unit is to be mounted to a fixed position for

use, install it horizontally.

Make sure to secure the main unit to prevent

accidents such as during an earthquake.

Securing with screws

Air Inlets

4 Locations

Remove the four feet at the bottom, and fasten using the

screws (M5 screws, 13 to 23 mm).

* Using

screws other than those designated may cause

the unit to break down.

* Leave a clearance of at least 10 mm from the bottom

surface of the unit to allow it to take in cool air.

Securing the projector (ceiling mount)

Be sure to ask your dealer to install the unit for you.

Installing the unit on your own may cause the unit to

fall resulting in injury.

Take the necessary actions to prevent the main unit

from falling off such as during an earthquake.

Regardless of the warranty period, JVC is not liable

for

any product damage caused by mounting the unit

with non-JVC ceiling fittings or to an environment that

is not suited for ceiling mount.

When using the unit with it suspended from a ceiling,

pay attention to the surrounding temperature. When

a heater is in use, the temperature around the ceiling

may be higher than expected.

attach the unit to the ceiling mount bracket, set the

torque between the range of 1.5N m to 2.0N m.

Tightening with torque exceeding the above range

may cause damage to the unit, which may result the

unit to fall.

Install

the outlet at an accessible height to unplug from

the wall. Or install the circuit breaker at an accessible

height to shut down the projector. If you need

information, please consult your authorized dealer or

specialist.

Set up

Adjusting the Position

Adjusting the elevation angle of the projector

The height and inclination of the unit (0 to 5 mm) can be

adjusted by turning the feet.

Lift the unit and adjust the four feet.

ContractExtend

Feet

Adjusting the position of the image

By using the lens shift feature of this unit, you can shift

the image upward/downward or to the left/right. Set it to

your preferred position.

Æ “Adjusting the Lens According to the Projection

Position” (P.

23)

0 10 3020 40

Lens movement range

Horizontal lens shift (%)

Vertical lens shift (%)

Lens shift Range

Up to about 80% of the

projected image

Horizontal Position: 0 % (Center)

Vertical Position

Up to about 34% of the

projected image

Vertical Position: 0% (Center)

Horizontal Position

■

The maximum vertical shift varies with the amount of

horizontal shift. Similarly, the maximum horizontal

shift also changes with the amount of vertical shift.

The

values on the graph are intended as a guide. Use

them for reference during installation.

Set up

Connecting the Projector

Do not turn on the power until connection is complete.

The connection procedures differ according to the device used. For details, please refer to the instruction manual

of the device to be connected.

This projector is used for projecting images. To output the audio of connected devices, please connect a separate

audio output device, such as an amplifier or speaker.

The images may not be displayed depending on the devices and cables to be connected.

A high speed HDMI cable (sold separately) that is HDMI-certified is recommended.

When using a standard cable, you are recommended to set the resolution of the equipment transmitting the video

to 1080i or lower.

Also, please refer to

“HDMI2 EDID”P. 47.

Some cables cannot be connected to this unit due to the size of their connector cover.

Connecting to the HDMI Input Terminal (Digital Input)

Connecting via HDMI cable

HDMI Output Terminal

BD/DVD Recorder, etc.

Laptop, etc.

HDMI Cable (Sold Separately)

This Unit

To [HDMI 1] or [HDMI 2] input

terminal

If noise occurs, move the laptop away from this unit.

Connecting through an AV amplifier

HDMI Cable

(Sold Separately)

BD/DVD Recorder, etc.

HDMI Cable (Sold Separately)

This Unit

To [HDMI 1] or [HDMI 2] input

terminal

Speaker Cable

(Sold Separately)

Speakers

AV Amplifier

the source device is connected to the projector through an intermediate device such as an AV amplifier or divider,

the video image may not appear depending on the specifications of the intermediate device.

In this case, connect the source device directly to the projector, and check whether the video image is displayed.

Set up

Connecting via HDMI-DVI conversion cable

HDMI-DVI Conversion Cable (Sold Separately)

To [HDMI 1] or [HDMI 2] input

terminal

This Unit

DVI Output Terminal

Desktop PC, etc.

If noise occurs, move the desktop PC away from this unit.

If the video is not displayed, try to reduce the length of the cable or lower the resolution of the video transmitting

equipment.

Connecting to the LAN Terminal

Desktop PC, etc.

Server

Hub

Network

Connection Cable

(Sold Separately)

This Unit

To [LAN] Terminal

The network is used to control this unit. It is not used for sending or receiving video signals.

Please contact your network administrator for information concerning the network connection.

Set “ECO Mode” to “Off” if LAN communication is performed in the Standby mode. (

P. 55)

For more information on control, please refer to [@TREX“External Control”P.

66.

Connecting to the RS-232C Terminal

RS-232C Terminal

Laptop, etc.

RS-232C Connection Cable (Sold Separately)

To [RS-232C] Terminal

This Unit

Set “ECO Mode” to “Off” if RS-232C communication is performed in the Standby mode. (

P. 55)

For more information on control, please refer to [@TREX

“External Control”P. 66.

Set up

Connecting to the TRIGGER Terminal

Trigger Input Terminal (Ø3.5)

Screen

Trigger Cable (Sold Separately)

To [TRIGGER] Terminal

This Unit

Do not use it to supply power to other devices.

Connecting to the audio terminal of another device may cause the device to malfunction or break down.

Using beyond the rated value will cause the unit to malfunction.

The trigger terminal outputs a voltage of 12 V. Exercise adequate caution to prevent short circuit.

The factory setting is “Off”. To change the setting, configure the “Trigger” item in the menu (

P. 54).

Connecting the Power Cord (Supplied Accessory)

Connect

the power cord supplied to the power input terminal on

the main unit

Insert the supplied power plug into the wall outlet.

Precautions to prevent fire and electric shock

The power consumption of this unit is large. Please connect it directly to the wall outlet.

When you are not using the projector, please unplug the power cord from the outlet.

Connect it using only the power cord supplied.

Do not use a voltage other than the indicated power voltage.

Do not damage, break or modify the power cord. Do not place a heavy object on the power cord, or heat or pull it.

Doing so may damage the power cord.

Do not unplug the power cord with wet hands.

Power Cord

(Supplied)

Set up

Viewing Videos

MEMO

When you are using 9, be sure to remove the lens cover.

Connect the power cord, and ensure that the “STANDBY/ON” indicator

lights up in red.

Turn on the power

Remote control: press the C [ON] button

Projector unit: press the A [STANDBY/ON] button

The

“STANDBY/ON” indicator light switches from red to green (light

goes off after the unit starts up).

(7 8) The lens cover opens.

LAMP WARNING

STANDBY/ON

TAN

DBY

LAMP WARNING

STANDBY/ON

TAN

DBY

During lamp startup

“STANDBY/ON” lights up (green)

In standby state

“STANDBY/ON” lights up (red)

Choose the image to project

Remote control: press the [HDMI 1] or [HDMI 2] button

Projector unit: press the [INPUT] button to switch the input

Play back the selected device to project the image.

To hide the image temporarily

Press the [HIDE] button on the projector unit or remote control

The “STANDBY/ON” indicator light starts to blink in green.

Press the [HIDE] button again to resume display of the image.

The power cannot be turned off when the image is temporarily hidden.

LAMP WARNING

STANDBY/ON

HDMI 1

INPUT

LENS MEMORY

HDMI 2 INFO.

MEMORY

MEMORY1 MEMORY2

1 3

This unit

Remote Control

Operate

Turn off the power

Remote control: press the B [STAND BY] button

Projector unit: press the A [STANDBY/ON] button

While the “Are you sure you want to turn off?” message is displayed, press the button again.

The lamp turns off, and the “STANDBY/ON” indicator switches from a green light to a red blinking light.

After the light goes off, the fan will run for about 100 seconds to cool down the lamp (Cool-down mode).

Do not disconnect the power cable while cooling is in progress.

After about 100 seconds, the “STANDBY/ON” indicator switches from a blinking red to a solid red light.

LAMP WARNING

STANDBY/ON

LAMP

WARNING

STANDBY/ON

TAN

DBY

In standby state

“STANDBY/ON” lights up (red)

In the Cool-down mode

“STANDBY/ON” blinking (red)

For 9, attach the lens cover manually.

For 7 8, the lens cover closes upon power off.

CAUTION

The power cannot be turned off within approximately 60 seconds after it has been turned on.

The power cannot be turned on again while cooling is in progress (100 seconds).

Pull out the power plug when the unit is not to be used for a prolonged period of time.

the indication of indicator differs from the description, refer to “Indicator Display on the Main Unit”P. 74 for details.

Operate

Adjusting the Projector Screen

Adjusting the Lens According to the Projection Position

Press the [LENS CONTROL] button, and use the [JKH I]

keys

to adjust Focus, Zoom (screen size), and Shift (screen

position)

Focus

Pressing the [LENS CONTROL] or [OK] button each time switches the mode

in the following sequence: “Focus” " “Zoom” " “Shift” " “Focus”...

Operation of the lens control feature is disabled when the lens lock is set to

“On”.

For more detailed information, please refer to

“Lens Control”P. 48.

Shift (Screen Position)

Adjustment

Zoom (Screen Size)

Adjustment

ABCD

Focus Adjustment

Press the [MENU] button once, or the [BACK] twice, to end

adjustment.

HDMI 1

INPUT

LENS MEMORY

PICTURE MODE

HDMI 2 INFO.

FILM CINEMA ANIME.

NATURAL

THX USER

MEMORY

MEMORY1 MEMORY2

ADVANCED

FORMAT

PIC.

ADJ.

COLOR

TEMP.

GAMMA

P.ANALYZER

MPC

LENS

CONTROL

LENS AP.

C.M.D.

Operate

Saving and Retrieving Adjustment Settings

The Focus, Zoom, and Shift settings can be saved or retrieved, so you can switch

easily to a different aspect ratio (screen size) according to the image.

In a state where no adjustment settings are saved (factory default), only “Lens

Memory Save” is displayed.

Operation

of the lens control feature is disabled when the lens lock is set to “On”.

Saving an adjustment data

Adjust focus, zoom, or shift (P. 23)

Press the [MEMORY MENU] button to display “Lens

Memory Save”

You can also save an adjustment data by selecting “Installation”"“Lens

Control”"“Lens Memory Save” from the menu.

MEMORY

BACK

-----

Back

Operate

Select

Exit

Lens Memory Save

Installation

Select the item to save, and press the [OK] button

The adjustment data is saved.

Items with no adjustment data saved are displayed as [----].

you have selected an item for which an adjustment data has already been

saved, the old data will be overwritten.

You can change the name when saving an item. (

P. 25)

The

maximum number of items can be saved is 10 for 7 8 and 5 for

Press the [MENU] button to exit

HDMI 1

INPUT

LENS MEMORY

PICTURE MODE

HDMI 2 INFO.

FILM CINEMA ANIME.

NATURAL

THX USER

MEMORY

MEMORY1 MEMORY2

ADVANCED

FORMAT

PIC.

ADJ.

COLOR

TEMP.

GAMMA

P.ANALYZER

MPC

LENS

CONTROL

LENS AP.

C.M.D.

Operate

Retrieving an adjustment data

Press the [MEMORY MENU] button to display “Lens Memory Select”

You can also retrieve an adjustment data by selecting “Installation”"“Lens Control”"“Lens Memory Select”

from the menu.

MEMORY1 and 2 can also be retrieved using the direct keys on the remote control.

BACK

-----

MEMORY2

-----

MEMORY1

MEMORY

Back

Operate

Select

Exit

Lens Memory Select

Installation

Select the adjustment data to retrieve, and press the [OK] button

The retrieved data is adjusted automatically.

If no adjustment data has been saved, the item will be grayed out and cannot be selected.

Renaming an adjustment data

Press the [MEMORY MENU] button to display “Lens Memory Name Edit”

You can also edit an adjustment data by selecting “Installation”"“Lens Control”"“Lens Memory Name Edit”

from the menu.

BACK

-----

MEMORY2

-----

MEMORY1

MEMORY

Lens Memory Name Edit

Back

Operate

Select

Exit

Installation

Select the adjustment data to edit, and press the [OK] button

An edit screen appears.

MEMORY1

}

{

]

[

)

(

;

SPACE

OKAll ClearClear

Name

Character List

Selection Cursor

Input Cursor

BACK

Back

Operate

Select

Exit

Lens Memory Name Edit

Installation

You can input up to 10 characters.

Characters that are usable include alphabets (upper or lower case), numeric characters, and symbols.

Pressing the [Back] button cancels the content that is currently being edited, and exits the edit mode.

After renaming, select “OK” and press the [OK] button

Press the [MENU] button to exit

Operate

Setting Screen Correction

Set Screen Adjust

By selecting the optimal correction mode

according to the characteristics of the screen in

use, corrections can be performed to reproduce

natural images with balanced colors.

BACK

3 21

Back

Operate

Select

Exit

Off

Front

Screen No.

Screen Adjust

High Altitude Mode

Anamorphic

Keystone

Installation Style

Pixel Adjust

Lens Control

Installation

This

item is not available when “Color Profile” is

set to “Off”.

For information on the screen and the

corresponding

correction mode, please visit our

website.

http://www3.jvckenwood.com/english/projector/screen/

MEMO

You can utilize the optional optical sensor and

dedicated

projector calibration software to make finer

adjustments.

For details on the dedicated projector calibration

software, please visit our website.

http://www3.jvckenwood.com/english/download/

index.html

Operate

Adjusting the Screen Size (Aspect)

The screen size of the projected image can be adjusted

optimally according to the original screen size (aspect)

that has been input.

Press the [MENU] button to display

the menu

Select “Input Signal”"“Aspect” from

the menu

BACK

Auto

16:9

Auto

Picture Position

3D Setting

Progressive

Mask

Aspect

Color Space

Input Level

Input Signal

Auto

HDMI2 EDID

Back

Operate

Select

Exit

Setting Description

4:3 Sets the screen size to 4:3. For

HD signals, the two sides are

reduced.

Displayed

only during

video signal

input.

16:9 Sets the screen size to 16:9.

For SD signals, the two sides

are expanded.

Zoom Enlarges the entire image.

* Not

selectable in the case of

HD signals.

Auto Positions the image at the

center with the entire image

enlarged.

Displayed

only during

PC signal

input.

Just Displays the input image in the

actual size.

Full Fills the entire screen with the

image

with the size (aspect) of

the input image ignored.

This item is grayed out and cannot be adjusted when

there is no signal, signal is out of range, or during 3D

or 4K input.

Press the [MENU] button to exit

Example of input image and screen size

HDMI Signal Input

Zoom

16:9

4:3

2.35:1

(Cinema

Scope)

Setting

Input Image

Output Image

PC Signal Input

1280×1024

Full

Just

Auto

Setting

Output Image

Input Image

Operate

Viewing 3D Movies

By using the 3D GLASSES (PK-AG1, PK-AG2, or PK-AG3) and 3D SYNCHRO EMITTER (PK-EM1 or PK-EM2), both

sold separately, you can enjoy 3D video images.

For 3D GLASSES and 3D SYNCHRO EMITTER that are compatible with this unit, please refer to

“Optional

Accessories”P. 9.

Installing the 3D SYNCHRO EMITTER

Connect 3D SYNCHRO EMITTER to the [3D SYNCHRO] terminal on the main unit

Installation Example

3D GLASSES

3D SYNCHRO EMITTER

PK-EM2

This Unit

PK-AG3

CAUTION

If PK-EM1 is used, adjust the position of the 3D SYNCHRO EMITTER such that the 3D GLASSES can receive the

signal from the 3D SYNCHRO EMITTER.

For more details, please refer to the instruction manual of PK-EM1.

Operate

Viewing 3D Movies

Connect this unit to a 3D-compatible

HDMI device, and turn on the power

to play back the 3D video image

For

details on how to play back 3D video images,

please refer to the instruction manual of the

player or recorder in use.

When

3D signals are received, the video image

switches automatically to the 3D format.

This unit supports the following 3D formats.

- Frame packing

- Side-by-side

- Top-and-bottom

the default setting, “3D Format” is set to “Auto”

for automatic projection of 3D images.

If the image does not switch to 3D automatically

Select “3D Format”

PICTURE MODE

FILM CINEMA ANIME.

NATURAL

THX USER

ADVANCED

FORMAT

PIC.

ADJ.

COLOR

TEMP.

GAMMA

P.ANALYZER

MPC

FORMAT

Pressing the [3D FORMAT] button each time

switches the mode in the following sequence:

“Auto” " “Side by Side” " “Top and Bottom” "

“2D” " “Auto”...

You can also perform setting from “Input

Signal”"“3D Setting”"“3D Format” in the

menu.

Format Description

Auto The format is detected and

configured automatically.

Side by Side Select this setting if the 3D input

signal is of the side-by-side

format.

Top and Bottom Select this setting if the 3D input

signal is of the top-and-bottom

format.

2D Select this setting if 2D images

are falsely recognized as 3D

ones.

* If a signal cannot be displayed as 3D image,

selecting the format does not switch the signal

to a 3D image.

For more information on possible input signals,

please refer to (

“Types of Possible Input

Signals”P. 73).

Turn of the power of the 3D GLASSES

and put them on

The PK-AG1 powers on automatically.

Adjusting 3D Movies

3D video images may appear differently to different

viewers. It may also be affected by your physical

condition at the time of viewing.

You are therefore recommended to adjust the video

images accordingly.

Select “Input Signal”"“3D Setting”

from the menu

Adjusting parallax (Parallax)

Adjust the displacement of the image for the left

and right eyes separately to obtain the best 3D

effect.

To do so, use the H I keys to move the cursor.

Setting range: -15 to +15

Adjusting crosstalk (Crosstalk Cancel)

Double images (overlapping of the left image with

the one on the right or vice versa) can be reduced

to deliver a clear quality.

To do so, use the H I keys to move the cursor.

Setting range: -8 to +8

Press the [MENU] button to exit

Operate

Selecting an Image Quality According to the

Video Type

Setting the Picture Mode

You can adjust the image quality according to the type of video image you are viewing.

Press the [PICTURE MODE] button to select “Picture

Mode”

You can also perform setting from “Picture Adjust”"“Picture Mode” in the

menu.

Item Description

Film*1 7 8

Reproduces faithfully the texture of movie films.

Cinema*1 Reproduces the image in vivid colors. Suitable for all

movies.

Animation*1 Suitable for animated works.

Natural*1

Image quality that focuses on natural color and gradation

reproduction. Suitable for drama footage, etc.

THX*1 7 8 Image quality certified by THX.

User 1 to User 6 *2 *3 Enables user-defined image quality data to be saved and

retrieved.

*1 For Picture modes with the *1 mark, the optimal settings for 2D and 3D signals

are

stored separately and applied automatically according to the selected mode.

Edited settings will also be saved separately.

No changes will be made to the Picture mode name.

*2 For 9,

“User 4” to “User 6” cannot be configured from the [PICTURE MODE]

button. Configure the setting using “Picture Adjust”"“Picture Mode” in the

menu.

*3 To view videos that support the x.v.Color format, select a user setting (“User 1”

to “User 6”) in “Picture Mode”, and set “Color Profile” to “x.v.Color”.

HDMI 1

INPUT

LENS MEMORY

PICTURE MODE

HDMI 2 INFO.

FILM CINEMA ANIME.

NATURAL

THX USER

MEMORY

MEMORY1 MEMORY2

ADVANCED

FORMAT

PIC.

ADJ.

COLOR

TEMP.

GAMMA

P.ANALYZER

MPC

LENS

CONTROL

LENS AP.

C.M.D.

Adjust/Set

Setting the Color Profile

By setting the “Color Profile” (color space information) according to the “Picture Mode”, you can fine-tune the image

quality according to the movie you are viewing.

Configure “Picture Mode” (P. 30), then select “Picture Adjust”"“Color Profile” in the

The selectable “Color Profile” settings vary according to the “Picture Mode” and also whether the signal is 2D

or 3D.

List of “Color Profile” for “Picture Mode” 9

Picture Mode 2D Signal Input 3D Signal Input Description

Cinema Cinema

—

Color space suitable for all movies.

Standard Standard Color space of the HDTV standard. *1

—

3D Cinema Color space suitable for all 3D movies.

Animation Animation

—

Color space that is suitable for animated works.

Standard Standard Color space of the HDTV standard. *1

—

3D Animation Color space suitable for 3D animation works.

Natural Video

—

Color space that is suitable for drama footage, etc.

Standard Standard Color space of the HDTV standard. *1

—

3D Video Color space suitable for 3D broadcasts.

User 1 to User 6 Standard When “Picture Mode” is set to any of the settings from “User 1” to “User

6”, you can select one of the “Color Profile” shown on the left.

See above for the description of the respective “Color Profile”.

Cinema

Video

Natural

3D Cinema

3D Video

3D Animation

x.v.Color*2*3 Color space that is close to that of the x.v.Color standard.

Off Disables color space adjustment.

Custom 1 to Custom 6 Saves the auto calibration values.

To perform auto calibration, you need to get ready a commercially

available optical sensor and the projector calibration software

program. For more details, please refer to our website.

*1 HDTV is the abbreviation for High Definition Television.

To view videos that support the x.v.Color format, select a user setting (“User 1” to “User 6”) in “Picture Mode”,

and set “Color Profile” to “x.v.Color”.

*3 x.v.Color is a wide color space standard for used in videos; it includes wider color gamut than the HDTV standard.

Adjust/Set

List of “Color Profile” for “Picture Mode” 7 8

Picture Mode 2D Signal Input 3D Signal Input Description

Film Film 1

—

Color space that is close to the characteristics of Eastman Kodak Company

movie films.

Film 2

—

Color space that is close to the characteristics of FUJIFILM Corporation movie

films.

Film 3

—

Color space suitable for digitally remastered piece of art based on a Technicolor

film.

—

3D Film*1 Color space suitable for 3D movies recorded in film.

Cinema Cinema 1 3D Cinema Original JVC cinema-specific color gamut that achieves a balance between

increased brightness and color vividness.

Cinema 2

—

Color space that is close to that of the DCI standard.

Standard Standard Color space of the HDTV standard. *2

—

3D Cinema Color space suitable for all 3D movies.

Animation Anime 1 3D Animation Color space that is suitable for CG animation works. Ideal for animated works

with bright colors.

Anime 2

—

Color space that is suitable for cel animation works. Ideal for animated works with

light colors.

Standard Standard Color space of the HDTV standard. *2

—

3D Animation Color space suitable for 3D animation works.

Natural Video 3D Video Color space that is suitable for drama footage, etc. making use of the increased

brightness.

Standard Standard Color space of the HDTV standard. *2

Reference

—

Color space that faithfully reproduces the video as it is.

—

3D Video Color space suitable for 3D video materials.

THX THX*3 3D THX*3 Color space of the THX standard.

User 1 to User 6 Standard When “Picture Mode” is set to any of the settings from “User 1” to “User 6”, you

can select one of the “Color Profile” shown on the left.

See above for the description of the respective “Color Profile”.

Cinema 1

Cinema 2

Anime 1

Anime 2

Video

Reference

3D Cinema

3D Video

3D Animation

x.v.Color*4*5 Color space of the x.v.Color standard.

Off Disables color space adjustment.

Custom 1 to Custom 6 Saves the auto calibration values.

To perform auto calibration, you need to get ready a commercially available

optical sensor and the projector calibration software program. For more

details, please refer to our website.

*1 The value is fixed during 3D signal input, and selection cannot be made.

HDTV is the abbreviation for High Definition Television.

*3 Color Profile is fixed when “THX” is selected as the “Picture Mode”.

*4 To view videos that support the x.v.Color format, select a user setting (“User 1” to “User 6”) in “Picture Mode”,

and set “Color Profile” to “x.v.Color”.

*5 x.v.Color is a wide color space standard for used in videos; it includes wider color gamut than the HDTV standard.

Adjust/Set

Adjusting to the Preferred Color (Color Management)

Based on the setting of the selected “Color Profile”, you can adjust each of the following colors according to your

preference: Red, Yellow, Green, Cyan, Blue, and Magenta.

Press the [ADVANCED MENU] button to display the “Color Profile” menu

Set “Color Management” to “On”, and press the [OK]

button

You

can also perform setting from “Picture Adjust”"“Color Profile”"“Color

Management” in the menu.

Adjust to the preferred color.

Select “Color Selection”, and press the H I keys to

select the color to adjust

For color adjustment, select the color from the

following:

“Red”, “Yellow”, “Green”, “Cyan”, “Blue”,

“Magenta”.

Adjust the selected color

Item

Setting Range

Description

Axis Position -30 to 30 Fine-tune the position

of the central axis of

the selected color.

Hue -30 to 30 Adjusts the hue (color

tone).

Saturation -30 to 30 Adjusts the color

saturation (vividness).

-30 (dull) to +30 (vivid)

Brightness -30 to 30 Adjusts the

brightness.

-30 (dark) to +30

(bright)

Selecting “Reset” resets all the adjustment data.

Pressing

the [HIDE] button on the remote control

enables you to check the image before

adjustment.

Press the [MENU] button to exit

BACK

Back

Operate

Select

Exit

Red

Film 1

Before

Brightness

Saturation

Hue

Axis Position

Color Selection

Color Management

Color Profile

Picture Adjust

Color Profile

Reset

Off

BACK

MagentaBlue

Cyan

Green Yellow

Red

Clockwise rotation: -

Counterclockwise rotation: +

Axis Position (Image)

Adjustable range when

Red is selected: ± 30°

with Red as the center

Back

Operate

Select

Exit

Red

Film 1

Before

Reset

Brightness

Saturation

Hue

Axis Position

Color Selection

Color Management

Color Profile

Picture Adjust

Color Profile

Adjust/Set

Adjusting Movies for Increased

Expressiveness (Multiple Pixel Control)

The new image-processing algorithm developed by JVC

helps to create a natural impression that is sharper at

areas in focus, and softer at areas that are not in focus,

enabling you to enjoy highly expressive 4K images with

a greater sense of depth.

Press the [MPC] button to display the

adjustment menu

You can also perform setting from “Picture

Adjust”"“MPC Level” in the menu.

BACK

PICTURE MODE

FILM CINEMA ANIME.

NATURAL

THX USER

ADVANCED

FORMAT

PIC.

ADJ.

COLOR

TEMP.

GAMMA

P. A N A LY Z E R

MPC

Back

Operate

Select

Exit

Auto

Before Reset

Smoothing

Dynamic Contrast

Enhance

Original Resolution

4K e-shift

MPC Level

Picture Adjust

Make adjustments according to your

preference

based on the setting of the

selected “Picture Mode”

* The factory setting varies with the “Picture

Mode”.

Item Setting Description

4K e-shift On (4K)/Off

(2K)

Switches the display

resolution.

Original

Resolution

Auto/4K/

1080p

For selecting a resolution for

the content you are viewing.

Enhance* 0 to 10 Enhances the sharpness of

the image.

Dynamic

Contrast

0 to 10 Enhances the contrast of the

image.

Smoothing 0 to 10 Enhances the blurriness of

the image for a softer effect.

NR 0 to 10 For reducing the noise of the

video image.

* In the case of 4K 50/60p and other input signals, the

respective setting values are saved.

the default “Original Resolution” setting (“Auto”), the

resolution is set automatically.

By increasing the setting range, you can expect

enhanced effects.

Images are displayed in the original resolution (2K)

when “4K e-shift” is set to “Off”.

“Original

Resolution”, “Enhance”, “Dynamic Contrast”,

and “NR” can be adjusted even when “4K e-shift” is set

to “Off”.

“4K e-shift” is fixed at “On” during 4K signal input.

“Original Resolution” is fixed at “Auto” during 4K

50/60p

signal input. “Dynamic Contrast”, “Smoothing”

and “NR” are grayed out.

“4K e-shift” is fixed at “Off” during 3D signal input.

Press the [MENU] button to exit

Toggling between the States before

and during Adjustment

Pressing

the [HIDE] button on the remote control enables

you to toggle between the states before adjustment and

during adjustment.

Adjust/Set

About the analysis screen

Pressing the [P.ANALYZER] button on the remote control displays the analysis screen. The operation varies with the

state of the OSD.

The analysis screen is not displayed during 4K 50/60p signal input.

Press the [P.ANALYZER] button

The frequency components of the input image are displayed.

The frequency components are distinguished using different colors.

When setting the “Original Resolution” manually, select “4K” if high-frequency components constitute the majority,

and a lower resolution if there are more low-frequency components.

Low High

Red Yellow Green Cyan

Blue

Frequency

Purple

Make adjustments while looking at the analysis screen

Press the [MPC] button to display the adjustment menu

You can also perform setting from “Picture Adjust”"“MPC Level” in the menu.

Make adjustments according to your preference based on the setting of the selected “Picture Mode”*

With “Enhance” selected, pressing the [P.ANALYZER] button displays the analysis screen and the area

where the “Enhance” effect is applied appears in “cyan” color.

With

“Dynamic Contrast” selected, pressing the [P.ANALYZER] button displays the analysis screen and the

area where the “Dynamic Contrast” effect is applied appears in “yellow” color.

With “Smoothing” and “NR” selected, pressing the [P.ANALYZER] button displays the analysis screen and

the area where the “Smoothing” and “NR” effects are applied appears in “magenta” color.

* You can make adjustments with the analysis screen displayed.

Increasing the value enhances the effect and the color displayed is darker.

Press the [P.ANALYZER] to exit the analysis screen

Adjust/Set

Fine-tuning the Image Quality

Adjusting the Output Value of the Projected Image (Gamma)

You can adjust the output value of the projected image with respect to the video signal input.

Example of gamma adjustment

The overall image appear brighter with respect to the original image, making the dark areas more visible.

255

0 255

The photos are for illustrative purposes only.

Input Value

Output Value

Increases the contrast with respect to the original image, creating a greater sense of depth.

255

0 255

The photos are for illustrative purposes only.

Input Value

Output Value

Press the [GAMMA] button

Pressing the [GAMMA] button each time switches the setting in sequence.

You can also perform setting from “Picture Adjust”"“Gamma” in the menu.

*1 The setting value varies with the model in use, as well as the “Picture

Mode”.

If HDR (high dynamic range) signal is detected, the setting value may

automatically switch to “D”.

If the setting value does not switch automatically when viewing HDR

contents, try to set to “D” manually.

If the image appears dark after switching to “D”, it is recommended to

adjust the image according to the procedures in “Procedures for adjusting

the image when gamma is set to “D””P. 39.

Gamma Settings for Different “Color Profile” 9

Color Profile Selectable Settings Description

Standard

Cinema

Animation

Video

3D Cinema

3D Video

3D Animation

Off

Normal Recommended setting for normal viewing.

A Places more emphasis on the gradation compared to the Normal

setting.

B Places more emphasis on the contrast compared to the Normal

setting.

C Places more emphasis on the brightness compared to the Normal

setting.

D Gamma suitable for viewing HDR (High Dynamic Range) content.

Custom 1 to Custom 3 Fine-tunes the gamma setting according to the user’s preference.

x.v.Color Normal* Recommended setting for normal viewing.

* When “Color Profile” is set to “x.v.Color”, the setting is fixed at “Normal”.

PICTURE MODE

FILM CINEMA ANIME.

NATURAL

THX USER

ADVANCED

FORMAT

PIC.

ADJ.

COLOR

TEMP.

GAMMA

P.ANALYZER

MPC

GAMMA

Adjust/Set

Gamma Settings for Different “Color Profile” 7 8

Color Profile Selectable Settings Description

Film 1 Film 1 Image is close to the characteristics of Eastman Kodak

Company movie films.

Film 2 Places more emphasis on the gradation compared to the

“Film 1” setting.

Custom 1 to Custom 3 Fine-tunes the gamma setting according to the user’s

preference.

Film 2 Film 1 Places more emphasis on the contrast compared to the “Film

2” setting.

Film 2 Image is close to the characteristics of FUJIFILM Corporation

movie films.

Custom 1 to Custom 3 Fine-tunes the gamma setting according to the user’s

preference.

Film 3 Film 1 Places emphasis on the contrast.

Film 2 Places emphasis on the gradation.

Custom 1 to Custom 3 Fine-tunes the gamma setting according to the user’s

preference.

3D Film Film 1 Places emphasis on the contrast.

Film 2 Places emphasis on the gradation.

Custom 1 to Custom 3 Fine-tunes the gamma setting according to the user’s

preference.

Standard

Cinema 1/Cinema 2

Anime 1/Anime 2

Video

Reference

3D Cinema

3D Video

3D Animation

Off

Normal Recommended setting for normal viewing.

A Places more emphasis on the gradation compared to the

Normal setting.

B Places more emphasis on the contrast compared to the

Normal setting.

C Places more emphasis on the brightness compared to the

Normal setting.

D Gamma suitable for viewing HDR (High Dynamic Range)

content.

Custom 1 to Custom 3 Fine-tunes the gamma setting according to the user’s

preference.

x.v.Color Normal*1 Recommended setting for normal viewing.

THX

3D THX

THX*2 Video of the THX standard.

*1 When “Color Profile” is set to “x.v.Color”, the setting is fixed at “Normal”.

When “Color Profile” is set to “THX”/“3D THX”, the setting is fixed at “THX”.

Fine-tuning to the Preferred Gamma Setting

You can perform fine adjustments based on the selected gamma adjustment setting.

Press the [ADVANCED MENU] button to display the gamma menu

You can also perform setting from “Picture Adjust”"“Gamma” in the menu.

BACK

Back

Operate

Select

Exit

White

2.2

Custom 1

Reset

Bright Level

Dark Level

Picture Tone

Color Selection

Correction Value

Gamma

Picture Adjust

Gamma

Adjust/Set

Adjust to the preferred setting

Item Description Setting

Color Selection Select “Color Selection”, and select the color to adjust White/Red/Green/Blue

Picture Tone Adjusts the overall brightness automatically for a well-balanced

result without compromising the gradation of the image.

-16 (darkens image for an

underexposed effect) to +16

(brightens

image for an overexposed

effect)

Dark Level Adjusts the dark areas of the input image. (Each of White/Red/

Green/Blue can be adjusted.)

To do so, use the H I keys to move the cursor.

-7 (darkens the shadows) to +7

(brightens the shadows)

Bright Level Adjusts the bright areas of the input image. (Each of White/Red/

Green/Blue can be adjusted.)

To do so, use the H I keys to move the cursor.

-7 (darkens the highlights) to +7

(brightens the highlights)

* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.

Selecting the Default Value for Making Adjustments

When one of “Custom 1” to “Custom 3” is selected in “Gamma”, you can select a “Correction Value”.

Select “Correction Value”, and press the H I keys to select a correction value (setting value) as a base value for

adjustment.

For details on the correction value (setting value), please refer to

P. 36 and P. 37.

Normal, A, B, C, D, 1.8, 1.9, 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 2.6, Import

7 8

When “Picture Mode” is set to “Film”:

Film 1, Film 2, Import

When “Picture Mode” is set to a value other than “Film”:

Normal, A, B, C, D, 1.8, 1.9, 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 2.6, Import

The smaller the value, the brighter the dark areas of the image will become. At the same time, the bright areas will

appear blown out.

Selecting “Import” enables you to select the gamma data created externally. The factory setting for “Import” is the

same as the “Normal” setting.

You can use the projector calibration software to customize the gamma data adjustment, and import the created

gamma data.

For more details, please refer to our website.

http://www3.jvckenwood.com/english/download/index.html

About gamma adjustment

When the gamma curve is a straight line:

The brightness and contrast of the video input will be

the same as that of the video output.

Area for which the gamma curve is above the straight

line (A):

Video output appears brighter than the input.

Area for which the gamma curve is below the straight

line (B):

Video output appears darker than the input.

Area for which the slope of the gamma curve is steep

(midtone) (C):

The grayscale range of the video output becomes

wider, and the contrast increases (D"D’).

0 255

255

D”

Gamma Curve

Input Value

Output Value

Dark

Bright

Adjust/Set

Procedures for adjusting the image when gamma is set to “D”

If the image appears dark when gamma is set to “D”, it is recommended to adjust the image according to the following

procedures.

While checking the overall image, adjust the setting value of “Picture Tone” in the + direction.

Focus on the bright area of the image and adjust the setting value of “Bright Level” in the + direction until the bright

area appears appropriate.

Focus

on the dark area of the image and adjust the setting value of “Dark Level” in the + or - direction until the dark

area appears appropriate.

Reducing the After-image of Fast-moving Images (Blur Reduction)

Clear Motion Drive (C.M.D.)

Optimal interpolation according to the content is made possible with the new high-definition image interpolation

technique that supports 3D images.

For some scenes, interpolation may cause distortion in the image. In this case, set to “Off”.

Intermediate Frame GenerationIntermediate Frame Generation

Interpolation Enabled

Original Image

Press the [C.M.D.] button

Pressing the [C.M.D.] button each time switches the mode in the following

sequence: “Off”"“Low”"“High”"“Inverse Telecine”"“Off”...

Setting Description

Off Interpolation is not performed.

Low Softens the image quality.

High Image quality becomes softer than that of the “Low” setting.

Inverse Telecine 60i/60p video images such as those of TVs and DVDs.

Suitable

for original images that are 24-frame film sources.

Does not function for 24p video images.

* C.M.D. is the abbreviation for Clear Motion Drive.

HDMI 1

INPUT

LENS MEMORY

HDMI 2 INFO.

MEMORY

MEMORY1 MEMORY2

LENS

CONTROL

LENS AP.

C.M.D.

Adjust/Set

Motion Enhance

Optimal image quality with reduced image blurring is made possible by enhancing the responsiveness of the liquid

crystal panel.

If the image outline is unnatural, set this item to “Off”.

Select “Picture Adjust”"“Blur Reduction”"“Motion Enhance” from the menu

Setting Description

Off Does not perform correction.

Low Reduces image blurring.

High Further reduces image blurring than “Low”.

If “Keystone” is set to a value other than “0”, the “Motion Enhance” is set to “Off” and grayed out.

If “Anamorphic” is set to other than “Off”, the “Motion Enhance” is set to “Off” and grayed out.

Viewing High Contrast Images (Lens Aperture)

JVC has developed an image analysis algorithm, which analyzes the state of the video image in real time, and controls

the aperture dynamically according to the image information.

This technology enables viewers to enjoy video images with enhanced contrast.

Press the [LENS AP.] button

Pressing the [LENS AP.] button each time switches the setting in sequence.

Setting Description

Auto 1 Image contrast is enhanced.

Auto 2 Places emphasis on the gradation.

Manual Does not perform dynamic control.

Select this setting to perform adjustment manually.

*1 Manual adjustment is disabled in the “Auto 1” and “Auto 2” setting.

To perform adjustment manually, select “Manual”.

When the setting is changed to Auto after performing manual adjustment, the

value set manually will be used as the aperture value for Auto.

HDMI 1

INPUT

LENS MEMORY

HDMI 2 INFO.

MEMORY

MEMORY1 MEMORY2

LENS

CONTROL

LENS AP.

C.M.D.

Adjust/Set

Adjustments and Settings in the Menu

Pressing the [MENU] button displays the menu.

Press the [JKH I] keys to select an item, followed by pressing the [OK] button to confirm the selection.

List of Menu Items

Picture Adjust

I Picture Mode ...................................................................................................................................................

P. 30

9 Clear Black ................................................................................................................................................. P. 43

9 Lamp Power ............................................................................................................................................... P. 43

9 Lens Aperture ............................................................................................................................................. P. 43

9 User Name Edit .......................................................................................................................................... P. 43

I Color Profile ..................................................................................................................................................... P. 31

Color Management ......................................................................................................................................... P. 33

I Color Temp. ..................................................................................................................................................... P. 44

I Gamma ............................................................................................................................................................ P. 36

Picture Tone .................................................................................................................................................... P. 38

Dark Level/Bright Level ................................................................................................................................... P. 38

I MPC Level ....................................................................................................................................................... P. 34

I Blur Reduction ................................................................................................................................................. P. 39

I Brightness ....................................................................................................................................................... P. 45

I Contrast ........................................................................................................................................................... P. 45

I Color ................................................................................................................................................................ P. 46

I Tint .................................................................................................................................................................. P. 46

Input Signal

I Input Level .......................................................................................................................................................

P. 46

I Color Space ..................................................................................................................................................... P. 46

I Aspect ............................................................................................................................................................. P. 47

I Progressive ...................................................................................................................................................... P. 47

I Mask ................................................................................................................................................................ P. 47

I 3D Setting ........................................................................................................................................................ P. 28

I Picture Position ................................................................................................................................................ P. 47

IHDMI2 EDID ..................................................................................................................................................... P. 47

Adjust/Set

Installation

I Lens Control ....................................................................................................................................................

P. 23

9 Focus ......................................................................................................................................................... P. 23

9 Zoom .......................................................................................................................................................... P. 23

9 Shift ............................................................................................................................................................ P. 23

9 Image Pattern ............................................................................................................................................. P. 48

9 Lock ........................................................................................................................................................... P. 48

9 Lens Memory Select ................................................................................................................................... P. 25

9 Lens Memory Save .................................................................................................................................... P. 24

9 Lens Memory Name Edit ............................................................................................................................ P. 25

9 Lens Center ................................................................................................................................................ P. 48

9 Lens Cover 7 8 .......................................................................................................................... P. 48

I Pixel Adjust ...................................................................................................................................................... P. 49

I Installation Style ............................................................................................................................................... P. 50

I Keystone ......................................................................................................................................................... P. 50

I Anamorphic ..................................................................................................................................................... P. 50

I High Altitude Mode .......................................................................................................................................... P. 50

I Screen Adjust .................................................................................................................................................. P. 26

Display Setup

I Back Color .......................................................................................................................................................

P. 54

I Menu Position .................................................................................................................................................. P. 54

I Signal Display .................................................................................................................................................. P. 54

I Logo ................................................................................................................................................................ P. 54

I Language ........................................................................................................................................................ P. 54

Function

I Trigger

............................................................................................................................................................. P. 54

I Off Timer .......................................................................................................................................................... P. 54

I ECO Mode ....................................................................................................................................................... P. 55

I Network ........................................................................................................................................................... P. 55

I Remote Code .................................................................................................................................................. P. 56

I Lamp Reset ..................................................................................................................................................... P. 59

Information

I Information .......................................................................................................................................................

P. 56

Adjust/Set

Picture Adjust

Picture Mode

You can adjust the image quality according to the type of video image you are viewing.

Æ “Setting the Picture Mode” (P.

30)

Clear Black

Adjusts the difference in brightness in an image electrically to produce an image with contrast.

Setting Description

Off Does not perform correction.

Low Mode with a mild effect.

High Mode with a strong effect.

Lamp Power

The brightness of the lamp can be set to “Low” or “High”.

The factory setting varies with the “Picture Mode”.

Continuous use at the “High” setting may cause the lamp to darken faster.

Lens Aperture

JVC has developed an image analysis algorithm, which analyzes the state of the video image in real time, and controls

the aperture dynamically according to the image information.

This technology enables viewers to enjoy video images with enhanced contrast.

Æ “Viewing High Contrast Images (Lens Aperture)” (P.

40)

Stopping down the aperture reduces the brightness and increases the contrast.

Setting range: -15 (stops down) to 0 (opens up)

User Name Edit

You can edit the “User 1” to “User 6” names in the Picture mode.

Characters that are usable include alphabets (upper or lower case), numeric characters, and symbols.

Enter not more than 10 characters.

BACK

User 1

}

{

]

[

)

(

;

SPACE

Name

After entry is complete, select

“OK” and press the [OK] button

Selection Cursor

Input Cursor

Back

Operate

Select

Exit

OKAll ClearClear

User Name Edit

Picture Adjust

Adjust/Set

Color Profile

By setting the “Color Profile” (color space information) according to the “Picture Mode”, you can fine-tune the image

quality according to the movie you are viewing.

Æ “Setting the Color Profile” (P.

31)

Color Management

Each of the colors is adjustable according to the user’s preference.

Æ “Adjusting to the Preferred Color (Color Management)” (P. 33)

Color Temp.

For setting the color temperature of the video image.

When “Picture Mode” is set to “THX” and when “Color Profile” is set to “x.v.Color”, the setting is fixed at 6500K.

Preset

Setting Description

Xenon 1 to Xenon 3 7 8

Selectable when “Picture Mode” is set to

“Film” or “Cinema”.

Color temperature that reproduces the characteristics of a xenon lamp

used in cinemas.

Xenon 1: A light source color that is emitted by a film projector

Xenon

2: A light source color emitted by a projector used for digital

cinema

Xenon 3: A light source color that looks cooler than that of “Xenon

2”

5500K, 6500K, 7500K, 9300K Increasing the value enhances the blue tone of the video image, while

decreasing the value enhances the red tone.

Custom 1 to Custom 3 The color temperature of video images can be adjusted manually and

saved as one of the three customized settings.

High Bright Color temperature that gives priority to brightness.

Custom

Setting Description

Gain Red, Gain Green, Gain Blue Adjusts each color in the bright parts of the video image.

Setting range: -255 (reduces the red/green/blue tone) to 0

(enhances the red/green/blue tone)

Offset Red, Offset Green, Offset Blue Adjusts each color in the dark areas of the video image.

Setting range: -50 (reduces the red/green/blue tone) to +50

(enhances the red/green/blue tone)

Gamma

You can adjust the output value of the projected image with respect to the video signal input.

Æ “Adjusting the Output Value of the Projected Image (Gamma)” (P.

36)

Picture Tone

Adjusts the overall brightness automatically for a well-balanced result without compromising the gradation of the image.

Æ “Fine-tuning to the Preferred Gamma Setting” (P.

38)

Dark Level/Bright Level

You can adjust the image quality to produce a sharp contrast in the brightness.

Æ “Fine-tuning to the Preferred Gamma Setting” (P.

38)

Adjust/Set

MPC Level

You can enjoy natural, expressive 4K images with a stronger sense of depth.

Æ “Adjusting Movies for Increased Expressiveness (Multiple Pixel Control)” (P.

34)

4K e-shift

Switches the display resolution.

Setting values: On (4K), Off (2K)

Original Resolution

For selecting a resolution for the content you are viewing.

Setting values: Auto, 4K and 1080p

* The

default “Original Resolution” setting is “Auto”, which switches the resolution automatically according to the type

of signal input.

Enhance

For adjusting the high-frequency areas. Increasing the value enhances the definition for a sharper image quality.

Setting range: 0 to 10

* In the case of 4K 50/60p and other input signals, the respective setting values are saved.

Dynamic Contrast

For adjusting the medium-frequency areas. Increasing the value enhances the contrast for a more dynamic image

quality.

Setting range: 0 to 10

Smoothing

For adjusting the low-frequency areas. Increasing the value enhances the blurriness of the image for a softer effect.

Setting range: 0 to 10

Prevents noise from becoming too pronounced.

Setting range: 0 (weak) to 10 (strong)

MEMO

“4K e-shift” is fixed at “On” during 4K signal input.

“Original

Resolution” is fixed at “Auto” during 4K 50/60p signal input. “Dynamic Contrast”, “Smoothing” and “NR” are

grayed out.

“4K e-shift” is fixed at “Off” during 3D signal input.

Blur Reduction

For reducing the after-image, which occurs in a fast-moving scene.

Æ “Reducing the After-image of Fast-moving Images (Blur Reduction)” (P.

39)

Brightness

For adjusting the brightness of the video image.

Setting range: -50 (darker) to +50 (brighter)

* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.

Contrast

For adjusting the difference in brightness to produce an image with contrast.

Setting range: -50 (little difference in brightness) to +50 (large difference in brightness)

* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.

Adjust/Set

Color

For adjusting the color density of the video image.

Setting range: -50 (lighter) to +50 (deeper)

* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.

Tint

For adjusting the hue of the video image.

Setting range: -50 (reddish) to +50 (greenish)

* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.

Input Signal

Input Level

For setting the dynamic range (gradation) of the video input.

If the image is not displayed properly even after selecting “Auto”, select an appropriate setting.

If the dynamic range is not appropriate, the bright areas become overexposed, and the dark areas become

underexposed.

Setting Description

Auto Sets the input signal level automatically.

Standard Select this setting if you are inputting video signals (dynamic range: 16 - 235).

Enhanced Select this setting if you are inputting PC signals (dynamic range: 0 - 255).

Super White Select this setting when inputting Super White-compatible device signals (dynamic

range: 16 - 255).

* When Picture Mode is set to “THX”, the setting is fixed at “Super White”.

Color Space

For setting the color space of the input signal.

If the image is not displayed properly even after selecting “Auto”, select an appropriate setting.

Setting Description

Auto Detects “YCbCr (4:4:4)”, “YCbCr (4:2:2)”, and “RGB” automatically.

YCbCr (4:4:4) Select this setting when inputting YCbCr (4:4:4) video signals.

YCbCr (4:2:2) Select this setting when inputting YCbCr (4:2:2) video signals.

RGB Select this setting when inputting RGB video signals.

Adjust/Set

Aspect

The screen size of the projected image can be adjusted optimally according to the original screen size (aspect) that

has been input.

Æ “Adjusting the Screen Size (Aspect)” (P.

27)

Progressive

For setting the interpolation method for the interlaced signals. If the image outline is unnatural, set this item to “Off”.

Setting Description

Auto Performs interpolation by automatically detecting whether the interlaced signals

are converted from 24p video images, such as those in film movies, or interlaced

signals of video materials.

Off Interpolates video images as interlaced signals of video materials, etc.

Mask

For hiding the peripheral area of the image with a mask (black strip).

Setting Description

Off Not masked.

Custom 1 to Custom 3 Masks about 0 to 220 pixels of the four sides of the

image.

The pixel count is 1920 pixels in the horizontal

direction and 1080 pixels in the vertical direction.

3D Setting

For setting 3D movies for viewing.

Æ “Viewing 3D Movies” (P.

28)

Picture Position (Horiz./Vert.)

Adjust the position if the edges of the image are partially missing due to the timing of horizontal and vertical

synchronization signals.

Adjustment cannot be made during 4K, 3D and 1080i signal input.

HDMI2 EDID

For changing the EDID mode of the [HDMI 2] terminal. Set to “A” under normal condition.

Images with resolution 1920x1080 or lower may not be displayed when some old devices are used.

In that case, connect to the [HDMI 2] terminal and set “HDMI2 EDID” to “B”.

EDID (Extended Display Identification Data) refers to the information, such as supported resolutions, exchanged

between devices.

Mask: black strip around the periphery

Off

Adjust/Set

Installation

Lens Control

Focus / Zoom / Shift

For adjusting the lens according to the projection position

Æ “Adjusting the Lens According to the Projection Position” (P. 23)

Image Pattern

Setting Description

On Displays the lens adjustment pattern.

Off Displays external signals, and does not display the lens adjustment pattern.

Lock

Setting Description

On Locks the lens to prevent any erroneous operation on the adjustments.

Operation of the lens control feature is disabled when “On” is selected.

Off Does not lock the lens.

Lens Memory Select / Lens Memory Save / Lens Memory Name Edit

The Focus, Zoom, and Shift settings can be saved or retrieved, so you can switch easily to a different aspect ratio

(screen size) according to the image.

Æ “Saving and Retrieving Adjustment Settings” (P.

24)

Lens Center

Returns the lens position to the center.

Lens Cover 7 8

Setting Description

Auto Opens/closes the lens cover according to the power on/off operation.

Open Leaves the lens cover open regardless of the power on/off mode.

Adjust/Set

Pixel Adjust

Adjust

For setting the adjustment feature to On (Memory 1 or Memory 2) or Off.

You can save the settings separately when an anamorphic lens is used and when you are using the projector with

a screen.

Adjust Area

Setting Description

Whole Adjusts the entire image.

Zone Enables fine adjustment of each zone by dividing the screen into 11 vertical x 11

horizontal zones.

Adjust Color

For selecting the color to adjust (“Red” or “Blue”).

Adjust Pattern Color

For setting the adjustment pattern color to “White” or “Yellow / Cyan”.

Adjust (Pixel)

When “Adjust Area” is set to “Whole”, adjustment can be made by moving in units of one pixel on the screen of the color

selected in “Adjust Color”.

Æ “Whole Adjust (Pixel) Operation Procedure” (P.

51)

* Adjustment cannot be made when “Adjust Area” is set to “Zone”.

Setting Description

H (Horizontal) Setting range: -2 (moves red/blue to the left) to +2 (moves red/blue to the right)

V (Vertical) Setting range: -2 (moves red/blue downward) to +2 (moves red/blue upward)

Adjust (Fine)

When “Adjust Area” is set to “Whole”, adjustment can be made by moving in units of 1/16 pixel on the screen of the

color selected in “Adjust Color”.

Æ “Whole Adjust (Fine) Operation Procedure” (P.

52)

When “Adjust Area” is set to “Zone”, the screen is divided into 11 vertical x 11 horizontal zones, and fine adjustment of

each zone is possible.

Æ “Zone Adjust Operation Procedure” (P. 53)

Setting Description

H (Horizontal) Setting range: -31 (moves red/blue to the left) to +31 (moves red/blue to the right)

V (Vertical) Setting range: -31 (moves red/blue downward) to +31 (moves red/blue upward)

Reset

Restores all pixel adjustment data to the factory default.

Adjust/Set

Installation Style

For setting to “Front”, “Ceiling Mount (F)”, “Rear”, or “Ceiling Mount (R)” according to the installation status of the

projector.

“Front” or “Ceiling Mount (F)” is set when projector is installed in the front with respect to the screen.

“Rear” or “Ceiling Mount (R)” is set when projector is installed in the rear with respect to the screen.

Keystone

For correcting any keystone distortion that occurs when the projector is installed at an angle with respect to the screen.

Vertical setting range: -16 to +16

*1 Increasing the value changes the aspect slightly.

Adjustment cannot be made during 4K 50/60p signal input.

Anamorphic

Configure this setting when an anamorphic lens is used.

Setting Description

A Projects the 2.35:1 image with it stretched in the vertical direction only.

B Projects the 16:9 image with it compressed in the horizontal direction only.

Off Projects the 2.35:1 image without any changes.

High Altitude Mode

Set to “On” when using the projector at a location of low atmospheric pressure (higher than 900 m above sea level).

Screen Adjust

By selecting the optimal correction mode according to the characteristics of the screen in use, corrections can be

performed to reproduce natural images with balanced colors.

Æ “Setting Screen Correction” (P. 26

)

Adjust/Set

Whole Adjust (Pixel) Operation Procedure

For making general adjustments to slight color fringing in the horizontal/vertical directions of the video image.

Set “Adjust Area” to “Whole”

Select “Adjust Color” and “Adjust Pattern Color”

Select “Adjust (Pixel)”, and press the [OK] button

The selected adjustment pattern and Adjustment (Pixel) window are displayed.

Color A.

GAMMA

BACK

Adjust.

COLOR

Color P.

A. Area

PIC.

TEMP FORMAT ADJ.

H 0

V 0

Red

Pixel Adjust

Back

Operate

Select

Whole Adjust (Pixel)

V (Vertical)

H (Horizontal)

Adjustment (Pixel) Window

Adjustment Pattern

Press the [OK] button to enter the Adjustment mode

Use

the [JKH I] keys to move and adjust the pixels in the vertical and horizontal directions across the entire screen.

The adjustment setting appears at the center of the Adjustment (Pixel) window.

Color A.

GAMMA

BACK

Adjust.

COLOR

Color P.

A. Area

PIC.

TEMP FORMAT ADJ.

H 0

V 0

Red

Pixel Adjust

Back

Operate

Select

Whole Adjust (Pixel)

Remote Control Operation

Guide

Color for

Adjustment

Pixel Adjustment Setting

After adjustment is complete, press the [BACK] button to exit the Adjustment mode

Remote Control Operation Guide

Button Name Description of Operation

[GAMMA] Changes “Adjust Color”.

[COLOR TEMP.] Switches between “Adjust (Pixel)” and “Adjust (Fine)”.

Switches to “Adjust (Pixel)” when “Adjust Area” is set to “Zone”.

[3D FORMAT] Changes “Adjust Pattern Color”.

[PIC ADJ.] Switches “Adjust Area”.

A zone cursor appears on the adjustment pattern when the “Zone” setting is selected.

Adjust/Set

Whole Adjust (Fine) Operation Procedure

For making general adjustments on the misalignment of the entire screen using “Adjust (Pixel)”, followed by making

fine adjustments.

Set “Adjust Area” to “Whole”

Select “Adjust Color” and “Adjust Pattern Color”

Select Adjust (Fine), and press the [OK] button

The selected adjustment pattern and Fine window are displayed.

The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.

Color A.

GAMMA

BACK

Adjust.

COLOR

Color P.

A. Area

PIC.

TEMP FORMAT ADJ.

0 ( 0 / 0 )

Red

Whole Adjust (Fine)

Pixel Adjust

Back

Operate

Select

V (Vertical)

H (Horizontal)

Fine Window

Adjustment Pattern

Press the [OK] button to enter the Adjustment mode

Use

the [JKH I] keys to move and adjust the pixels in the vertical and horizontal directions across the entire screen.

The adjustment setting appears at the center of the Fine window.

H −20 （−20 / −20）

V 5 （ 5 / 5）

Color A.

GAMMA

BACK

Adjust.

COLOR

Color P.

A. Area

PIC.

TEMP FORMAT ADJ.

0 ( 0 / 0 )

Red

Whole Adjust (Fine)

Pixel Adjust

Indicates the maximum and

minimum misalignment value of

the entire screen.(Max. / Min.)

Adjustment Setting

Remote Control Operation

Guide

Color for

Adjustment

Pixel Adjustment Setting

Back

Operate

Select

After adjustment is complete, press the [BACK] button to exit the Adjustment mode

MEMO

If both the maximum overall screen misalignment of H (horizontal direction) and V (vertical direction) are “31”, you

cannot select a value that is larger than the displayed setting even when the adjustment setting is lower than the

maximum value.

If the minimum overall screen misalignment is “-31”, you cannot select a value that is smaller than the displayed

setting even when the adjustment setting is higher than the minimum value.

Adjust/Set

Zone Adjust Operation Procedure

For fine-tuning misalignments on a part of the screen after adjusting the overall screen misalignment using “Adjust

(Pixel)” and “Adjust (Fine)”.

The screen can be divided vertically and horizontally into 10 sections for partial adjustments to be made.

Set “Adjust Area” to “Zone”

Select “Adjust Color” and “Adjust Pattern Color”

Select Adjust (Fine), and press the [OK] button

The selected adjustment pattern and Zone Adjustment window are displayed.

The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.

Color A.

GAMMA

BACK

Adjust.

COLOR

Color P.

A. Area

PIC.

TEMP FORMAT ADJ.

0 / 0

Position

Red

Zone Adjust

Pixel Adjust

V (Vertical)

H (Horizontal)

Zone Adjustment Window

Zone Cursor

Adjustment Pattern

Back

Operate

Select

Press the [JKH I] keys to move the cursor to the point to be adjusted

Press the [OK] button to enter the Adjustment mode

Use

the [JKH I] keys to move and adjust the pixels in the vertical and horizontal directions across the entire screen.

The adjustment setting appears at the center of the Zone Adjustment window.

H −31

V 7

Color A.

GAMMA

BACK

Adjust.

COLOR

Color P.

A. Area

PIC.

TEMP FORMAT ADJ.

0 / 0

8 / 5

Position

Red

Zone Adjust

Pixel Adjust

Position

Adjustment Setting

Cursor Position

Remote Control Operation

Guide

Color for

Adjustment

Pixel Adjustment Setting

Back

Operate

Select

After adjustment is complete, press the [BACK] button to exit the Adjustment mode

Adjust/Set

Display Setup

Back Color

For setting the color of the background to “Blue” or “Black” when there is no signal input.

Menu Position

For setting the display position of the menu.

Signal Display

Setting Description

On Shows the input terminal for 5 seconds when input is switched.

Off Not displayed.

Logo

Setting Description

On Displays the “D-ILA” logo for 5 seconds during startup.

Off Not displayed.

Language

For setting the display language to “日本語”, “English”, “Deutsch”, “Español”, “Italiano”, “Français”, “Português”,

“Nederlands”, “Svenska”, “Norsk”, “Русский”, “中文”, or “繁體中文”.

Function

Trigger

For setting whether to supply a 12 V output to devices such as an external screen equipped with a trigger function.

Setting Description

Off No output.

On (Power) Outputs control signals (12 V) from the trigger terminal when the power is turned

on.

When the power is turned off, the control signal output is stopped when the

cooling function starts.

On (Anamo) Outputs control signals when the “Anamorphic” setting is switched from “Off” to “A”

or “B”.

Off Timer

For setting the duration before the power turns off automatically when the projector is not operated.

Setting values: “Off”, “1 Hour”, “2 Hours”, “3 Hours” and “4 Hours”

Adjust/Set

ECO Mode

Setting Description

On Enables “ECO Mode” to minimize power consumption in the Standby mode.

RS-232C / LAN communication cannot be used in the Standby mode.

If there is no signal transmission and operation for 20 minutes while an image

projected, the power management switches the equipment automatically into

standby mode.

Off Select this option to control via RS-232C / LAN communication in the Standby

mode or if Control4 is to be used.

Network

Specify the settings below during external control such as from a PC or smartphone.

Setting Description

DHCP Client On Obtains the IP address automatically from the DHCP server inside the connected

network.

Off For configuring the network settings manually.

IP Address For configuring the IP address.

Subnet Mask For configuring the subnet mask.

Default Gateway For configuring the default gateway.

MAC Address Displays the MAC address of the unit.

Set Applies the network settings.

Control4 Set to “On” to allow Control4 SDDP to detect this unit.

When

this unit is not connected to an environment under the control of the controller

and Control4 SDDP from the Control4 Corporation, set this to “Off”.

Glossary of Network Terminology

DHCP

: Abbreviation for Dynamic Host Configuration Protocol. This is a protocol for the network

to assign an IP address automatically to the connected device.

IP Address : Numeric characters for identifying the device that is connected to the network.

Subnet Mask : Numeric characters that define the bit count used for the network address that is a

segment of the IP address.

Default Gateway : Server for communicating beyond the network that is divided by the subnet mask.

MAC Address : Abbreviation for Media Access Control address. This is a number that is unique to each

network adapter. Each of the network adapters is assigned with a unique MAC address.

Adjust/Set

Remote Code

For changing the remote control code.

You need to configure the remote control according to the settings of this unit.

On the remote control unit, press the [MENU] and [BACK] buttons at the same time for three seconds or longer to

switch the code.

The backlight of the remote control blinks 3 times: change the remote control code to “A”

The backlight of the remote control blinks 2 times: change the remote control code to “B”

Setting Description

A Change the remote control code from “B” to “A”.

B Change the remote control code from “A” to “B”.

Lamp Reset

For resetting the lamp time to “0”.

Æ “Resetting the Lamp Time” (P.

59)

Information

Setting Description

Input Displays video input terminal.

Source

(Displayed only during video signal input)

Displays the input source.

Resolution

(Displayed only during PC signal input)

Displays the image resolution.

H Frequency

(Displayed only during PC signal input)

Displays the horizontal frequency.

V Frequency

(Displayed only during PC signal input)

Displays the vertical frequency.

Deep Color Displays the color bit depth of the input video signal.

Not displayed when YCbCr (4:2:2) is input.

Displayed when Deep Color information is received from the source device.

Color Space Displays the color space of the input signal.

Lamp Time Displays the lamp time.

Soft Ver. Displays the firmware version.

PS Ver. Displays the version of image quality data.

Adjust/Set

Replacing the Lamp

The lamp is a consumable item. If the image appears dark or the lamp goes out, replace the lamp unit.

When the lamp replacement time approaches, the user is notified with a message displayed on the screen and by

the indicator. (

P. 74)

Lamp Replacement Procedure

CAUTION

Do not insert your hands into the lamp compartment.

This could cause significant deterioration in the

performance of the equipment, or lead to injury and

electric shock.

not replace the lamp immediately after the unit has

been used. Allow a cooling period of at least one hour

before replacement. The temperature of the lamp is

still high, and may cause burn injuries.

Do not subject the lamp unit to shock. Doing so may

cause lamp blowout.

not use a flammable air duster to clean the internal

parts of the unit. Doing so may cause fire.

Use

only genuine replacement parts for the lamp unit.

Also, never attempt to reuse an old lamp unit. This

may cause the unit to malfunction.

not touch the surface of a new lamp. Doing so may

shorten the lamp life and cause lamp blowout.

When replacing the lamp, be careful not to injure

yourself as the lamp may be broken.

When replacing the lamp of a projector suspended

from the ceiling, work at height is required. This is a

dangerous operation. Please consult our service

center.

Pull out the power plug from the power

outlet

Remove the lamp cover

Remove the screw of the lamp cover with a t

screwdriver.

Loosen the screws of the lamp unit

Loosen the screws with a t screwdriver.

Pull out the lamp unit

Hold the lamp unit at the dents at the top and

bottom, and pull it out.

Maintenance

Install the new lamp unit

Tighten the screws of the new lamp

unit

Tighten the screws with a t screwdriver.

Attach the lamp cover

Insert the two tabs at the top and bottom of the

lamp cover into the unit.

Tighten the screws with a t screwdriver.

MEMO

Usable lamp life

When the lamp is used with “Lamp Power” set to

“Low”,

the lamp life on this unit is approximately 4500

hours. This is the average usable time and not a

guaranteed value.

The

lamp life may not reach 4500 hours depending on

the operating conditions.

When

the lamp has reached the end of its usable life,

deterioration progresses rapidly.

When the video image appears dark, when the color

tone looks unnatural, or when the image flickers,

replace the lamp unit with a new one promptly.

Purchasing a lamp unit

Please consult your authorized dealer or nearby service

center.

Lamp unit

Product no.: PK-L2615U

* Not suitable for household room illumination.

Lamps with a different product number or those for

other projector models cannot be used.

Information about the lamp

An ultra-high pressure mercury lamp with a high internal

pressure is used in the projector.

Due to the characteristics of this lamp, it may blow out

with a loud noise or go out when it is subject to shock or

after

using for a prolonged period of time (the time before

the lamp blows out or goes out varies considerably with

each lamp as well as the operating conditions).

After replacing the lamp

Do not place the removed lamp unit at a place that is

within reach by children or anywhere near

inflammable items.

Dispose used lamp units in the same way as

fluorescent

lamps. Follow the regulations of your local

community for disposal.

Maintenance

Resetting the Lamp Time

Reset the lamp time when you have replaced the lamp.

It provides an estimated timing for lamp replacement

Resetting the lamp time from the menu

screen

Press the [MENU] button to display

the menu

Select “Function”"“Lamp Reset”

from the menu

BACK

Back

Operate

Select

Exit

Off

Lamp Reset

Remote Code

Network

ECO Mode

Off Timer

Trigger

Function

Off

On the “Reset Lamp Time?” screen,

select

“Yes” and press the [OK] button

The lamp time is reset to zero.

NoYe s

Reset Lamp Time?

Resetting the lamp time using the remote

control

Insert the power plug into the power

outlet

Make sure that you operate the

remote control in the Standby mode

(the power plug is inserted into the

outlet, but the power is not turned on)

Press in the order as shown.

Make sure that you press a button within two

seconds after the last button is pressed.

Press the last button for at least two seconds.

Press for 2

seconds or longer

The “LAMP” indicator and “STANDBY/ON”

indicator blink alternately for three seconds.

After that, the unit switches to the Standby

mode.

MEMO

Reset the lamp time only when you have replaced the

lamp.

If the lamp time is reset while a lamp is in use, you may

lose track of the timing for replacing the lamp. Doing

so may result in using the lamp beyond the estimated

limit, thereby causing lamp blowout.

Maintaining the Cabinet and Remote Control

Gently wipe off dirt on the cabinet with a soft cloth.

If it is extremely dirty, wet a cloth in water, wring dry and use it to wipe off the dirt, followed by wiping again with a

dry cloth.

Pay attention to the following as the cabinet may deteriorate in condition or the paint may come off.

Do not wipe with thinner or benzine

Do not allow prolonged contact with rubber or plastic products

Do not spray volatile chemicals such as insecticide

Maintenance

Cleaning and Replacing the Filter

Clean the filter regularly Otherwise, the air intake

efficiency may deteriorate, and malfunction may occur.

CAUTION

Make sure that you pull out the power plug from the

outlet before cleaning or replacing the filter.

Before

turning this unit upside down and placing it on

the floor or a table, make sure that you lay a soft rag

in advance to prevent the projector from being

scratched.

Remove the inner filter

Pull out while

pushing down the

tab

Clean the filter

Wash the filter with water and dry it in a shaded

area.

If the filter is extremely dirty, clean it with a

neutral detergent. Put on rubber gloves when

using a neutral detergent.

After washing the filter with water, make sure

that it is completely dry before reinstalling.

Otherwise, electric shock or malfunction may

occur.

Do not clean the filter with a vacuum cleaner or

air duster. The filter is soft and may be easily

damaged.

Reinstall the inner filter

Check that the left

and right tabs are

locked onto the unit

If the filter is damaged or too dirty to be

cleaned

Replace with a new filter. A dirty filter will dirty the

internal

parts of the unit and cause shadows to appear

on the video image.

To purchase a new filter or when there is dirt in the

internal parts of the unit, consult your authorized

dealer or nearby service center.

Inner filter (exchangeable filter)

Product no.: PC010661199

Maintenance

Troubleshooting

Before sending the unit to your authorized dealer for repair, please check the following points.

The following symptoms are not malfunctions.

You do not need to worry about the following symptoms if there is no abnormality on the screen.

A part of the top or front surface of the unit is hot.

A creaking sound is heard from the unit.

An operating sound is heard from the inside of the unit.

Color smear occurs on some screens.

This unit is a digital device. This unit may become unable to operate normally due to external static or noise.

Perform the following operations when such malfunctions occur.

If the unit is in the Standby mode, pull out the power plug, followed by inserting it again

Press the A [STANDBY/ON] button on the main unit to turn on the power again

When “High Altitude Mode” is set to “On”, and “Lamp Power” is set to “High” during 3D mode, the fan will

make louder noise than usual since it is designed to run at high speed in 3D mode.

Power is not supplied

Check Action Refer to

Is the power cord disconnected? Insert the power cord (plug) firmly. P. 20

Is the lamp cover properly shut? If the unit is in the Standby mode, remove the power plug

and

close the lamp cover properly. After that, insert the plug

again.

P. 58

Is the lamp in the Cool-down mode? After exiting the Cool-down mode, turn on the power again. P. 22

Power shuts down automatically

Check Action Refer to

Has “ECO Mode” been configured? Set “ECO Mode” to “Off”. P. 55

Has “Off Timer” been configured? Set “Off Timer” to “Off”. P. 54

Are the air inlets and exhaust vent

blocked?

Leave proper clearance when installing the unit. P. 10, 11

P. 15

Is the filter dirty? Clean the filter. P. 60

Troubleshooting

Video image does not appear

Check Action Refer to

Is the correct external input selected? Select the correct external input terminal. P. 21

Is the power of the AV device turned on? Turn on the power of the AV device and play the video. P. 18

Is the AV device properly connected? Connect the AV device properly. P. 18

Are the correct signals being output from

the AV device?

Set the AV device properly. P. 18

Is the cable in use an HDMI-certified

cable?

Use an HDMI-certified high-speed cable. Also, use as

short a cable as possible.

P. 18

Is an intermediate device (AV amplifier,

divider, etc.) in use?

Change the sequence of turning on the source device,

intermediate

device and the projector. And after turning on

each device, ensure that the signal output is stable before

turning on the next device.

P. 18

Is an old source device in use? Change the resolution setting of the source device. For

details on how to change the setting, please refer to the

instruction manual of the source device. Or, try connecting

to the HDMI2 terminal and set “HDMI2 EDID” to “B”.

P. 47

3D images do not appear

Check Action Refer to

Do you see two images displayed side by

side?

Set “3D Format” to “Side by Side”

Video images in the “Side by Side” format may not be

recognized automatically in the case of 3D video images.

P. 29

Is an intermediate device (AV amplifier,

divider, etc.) in use?

Connect the source device to the projector directly, and

check whether there is any improvement in the condition.

If the condition improves, it is likely that this is not caused

by malfunction of the projector.

P. 18

Is the cable in use an HDMI-certified

cable?

Use an HDMI-certified high-speed cable.

Also, use as short a cable as possible.

P. 18

Is the power of the 3D GLASSES turned

on?

If you are using the PK-AG2 or PK-AG33D GLASSES, turn

on the power manually.

Check the

instruction

manual

of the 3D

GLASSES and

3D SYNCHRO

EMITTER.

Are the 3D GLASSES charged? Check whether the PK-AG1 battery of the 3D GLASSES

has run out, and whether PK-AG2 and PK-AG3 are

charged.

Are the 3D GLASSES and 3D

SYNCHRO EMITTER too far away from

each other?

Position them at an appropriate distance.

Is the 3D GLASSES and 3D SYNCHRO

EMITTER combination correct?

Check the model name of 3D GLASSES and 3D

SYNCHRO EMITTER, and use the correct combination.

P. 9

3D video image looks unnatural

Check Action Refer to

Are there overlapping video images? If there are overlapping video images partially, this is due

to the crosstalk phenomenon.

In this case, adjust “Crosstalk Cancel” accordingly.

P. 29

If there are overlapping video images partially, this is due

to the crosstalk phenomenon.

This phenomenon often occurs when there are drastic

changes in the brightness.

In this case, set Lamp Power to “High”

P. 43

Troubleshooting

Video image looks unnatural

Colors are unnatural

Check Action Refer to

Is the color space of the input signal

correctly set?

The color may turn out unnatural when the input signal is

different from that in the projector setting.

Set the “Color Space” for “Input Signal” correctly.

P. 46

Is the image correctly adjusted? Adjust “Color” and “Tint” accordingly. P. 46

Is the AV device properly connected? Connect the AV device properly. P. 18

* The video image may appear slightly reddish immediately after starting up. This is not a malfunction.

Video image is fuzzy

Check Action Refer to

Is the focus correctly adjusted? Adjust the focus. P. 23

Is the unit placed too near or too far away

from the screen?

Set the unit at a correct distance from the screen. P. 71

Video image flickers

Check Action Refer to

Do you see horizontally-extended,

overlapping video images?

In this case, set “3D Format” to “Auto” P. 29

Are you viewing the video images under

a fluorescent light?

This is caused by interference between the 3D glasses with

the flickers of the fluorescent light.

View with the fluorescent light turned off.

—

Is “Lens Aperture” set to “Auto 1” or “Auto

2”?

Set “Lens Aperture” to “Manual” P. 40

* Flickers

may sometimes occur upon starting up the projector unit, or immediately after the projector is changed from

floor-standing to ceiling mounted. This is attributable to the lamp or drive mechanism, and is likely not caused by

malfunction of the projector.

Projected image is dark

Check Action Refer to

Is the lamp near exhaustion? Check the lamp time in the “Information” menu. Prepare a

new lamp unit or replace as soon as possible when the

lamp is near exhaustion.

P. 56

Is the aperture closed? Set “Lens Aperture” to “Auto 1” or “Auto 2”, or set to

“Manual” and open up the aperture manually.

P. 40

Is “Lamp Power” set to “Low”? Set “Lamp Power” to “High” P. 43

Video image appears horizontally (vertically) extended

Check Action Refer to

Is “3D Format” set to “Side by Side”? Set “3D Format” to “Auto” P. 29

Is “Anamorphic” set to a setting other

than “Off”?

Set “Anamorphic” to “Off” P. 50

Troubleshooting

Striped patterns appear on the screen

Check Action Refer to

Does the fabric of the screen have a

regular pattern?

Interference fringes may sometimes occur between the

fabric

pattern and the pixels. Please consult the authorized

dealer.

—

Video images are missing

Check Action Refer to

Has screen mask been configured? Set “Mask” to “Off”. P. 47

Is the display position misaligned? Alter the “Picture Position” value so that the entire image

appears on the screen.

P. 47

Remote control does not work

Check Action Refer to

Are the batteries correctly loaded? Match the polarities (t s) correctly when loading the

batteries.

P. 14

Are the batteries exhausted? Replace with new batteries. P. 14

Is there an obstructing object between

the remote control and remote sensor?

Remove any obstructing object. P. 14

Is the remote control held too far away

from the unit?

Hold the remote control closer to the sensor during use. P. 14

Are the IR (infrared) 3D GLASSES and

3D SYNCHRO EMITTER in use?

As there is a possibility of signal interference, when you are

using the IR (infrared) 3D GLASSES together with the 3D

SYNCHRO EMITTER, try adjusting the orientation of the

3D SYNCHRO EMITTER.

P. 28

The lens cover does not close 7 8

Check Action Refer to

Is “Lens Cover” set to “Open”? Set “Lens Cover” under “Lens Control” in the setting menu

to “Auto”.

P. 48

Noise is heard

Check Action Refer to

Is the exhaust vent blocked?

Is the unit used near a heater or air-

conditioner?

Check the installation condition of the projector.

When the surrounding temperature of the projector is high,

the fan revolution speed increases to protect the projector

unit, hence a louder operating sound.

P. 15

Are you viewing 3D video images? “Lamp Power” is set automatically to “High” to ease viewing

of 3D video images, hence a louder fan operating sound.

If you are bothered by the sound, set it to “Low”.

P. 43

Is the “Picture Mode” or “Color Profile”

changed?

7 8 only

Operating sound is generated by the cinema filter. This is

not a malfunction.

—

Did you change the “4K e-shift” setting

for “MPC Level”?

Switching sound is generated. This is not a malfunction.

—

There are small black or colored dots on the screen

The D-ILA device is manufactured using high-precision technologies, but there may be some (less than 0.01%) missing

pixels or pixels that remain permanently lit. This is not a malfunction.

Troubleshooting

When the following messages appear...

Message Description Action

No Input

No device is connected to the input

terminal.

The input terminal is connected but

there is no signal.

Input the video signals.

HDMI-1

A video signal that cannot be used with

this unit has been input (The names of

input terminals such as “HDMI-1” and

“HDMI-2” will be displayed in yellow).

Input video signals that can be used.

(P.

73)

BACK

Back

Lamp replacement

Indicates that the lamp needs to be

replaced soon.

clear the message, press the [BACK]

button on the operation panel of the

projector unit or the remote control.

Get ready a new lamp unit and replace

as soon as possible. Reset the lamp time

after replacing the lamp. (P. 57, 59)

Troubleshooting

External Control

It is possible to control this unit by connecting it to a PC using an RS-232C cross cable (D-sub 9-pin).

The projector can be controlled by connecting it to a PC through the computer network with a LAN cable for control

commands to be sent to the projector.

Æ “ Network ” (P.

55)

Please use it after you have gained proper understanding from professional books or consulting the system

administrator.

RS-232C Specifications

Pin No. Signal Function Signal Direction

2 RxD Receive data PC "

This unit

3 TxD Transmission data This unit " PC

5 GND Signal ground

—

1, 4, 6 - 9 N/C

— —

PC refers to the controller, such as a personal computer.

Mode Non-synchronous

Character length 8 bit

Parity None

Start bit 1

Stop bit 1

Data rate 19200 bps

Data format Binary

This Unit

D6 D7D4 D5D2 D3D0 D1

Stop bitStart bit

TCP/IP Connection

Before controlling via LAN, it is necessary to establish connection of the TCP layer by a “3-way handshake”, followed

sending out “PJREQ” and receiving “PJACK” within five seconds after the projector sends out “PJ_OK” for connection

authentication.

If you are unable to complete sending within five seconds, or when “PJ_NG” or “PJNAK” is received, check the operating

status of the projector, followed by performing the steps again starting from establishment of a TCP connection.

Projector Control

Connection Authentication Procedure

PJACK

PJREQ

PJ_OK

Within 5 Seconds

Controlling PC

3-way Handshake

TCP Port No. 20554

Establishment of TCP Connection

Projector

Others

Command Format

The command between this unit and the computer consists of “Header”, “Unit ID”, “Command”, “Data” and “End”.

Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n bytes), End (1 byte)

Header

This binary code indicates the start of communication.

Binary Code Type Description

21 Operating command PC "

This unit

3F Reference command PC "

This unit

40 Response command This unit " PC

06 ACK This unit " PC (returns to PC after the command is accepted without

error)

Unit ID

This is a code that specifies the unit. The binary code is fixed at “8901”.

Command and data

Operating command and data (binary code)

Command

Type Description

0000

Connection

check

Check whether communication is

enabled between this unit and the

PC during standby.

5057 Power

supply

During standby

31: Turns on the power

When power is on

30: Turns off the power (Standby

mode)

4950 Input When power is on

36: HDMI 1

37: HDMI 2

5243 Remote

control

Sends the same code as the

supplied remote control.

“Remote Control

Code”P.

Reference command and data (binary code)

Command

Type Description

5057 Power

supply

During standby or when power is

30: Standby mode

31: When power is on

32: In the Cool-down mode

34:

When error occurs on this unit

4950 Input When power is on

36: HDMI 1

37: HDMI 2

End

This code indicates the end of communication. The binary code is fixed at “0A”.

Others

Remote Control Code

Binary code is sent during communication.

The

following applies to the case when the remote control code is “A”. In the case of “B”, add “36” to the beginning

of the code.

Remote Control Button Name Binary Code

STAND BY 37 33 30 36

ON 37 33 30 35

HDMI 1 37 33 37 30

HDMI 2 37 33 37 31

INFO. 37 33 37 34

C.M.D. 37 33 38 41

LENS CONTROL 37 33 33 30

MEMORY MENU 37 33 44 34

MEMORY 1 37 33 44 38

MEMORY 2 37 33 44 39

LENS AP. 37 33 32 30

MPC 37 33 46 30

P.ANALYZER 37 33 35 43

HIDE 37 33 31 44

37 33 30 31

37 33 30 32

37 33 33 34

37 33 33 36

OK 37 33 32 46

Remote Control Button Name Binary Code

MENU 37 33 32 45

BACK 37 33 30 33

FILM 7 8 37 33 36 39

CINEMA 37 33 36 38

ANIME. 37 33 36 36

THX 7 8 37 33 36 46

USER 37 33 44 37

USER1 37 33 36 43

USER2 37 33 36 44

USER3 37 33 36 45

3D FORMAT 37 33 44 36

ADVANCED MENU 37 33 37 33

GAMMA 37 33 37 35

COLOR TEMP. 37 33 37 36

COLOR PROFILE 37 33 38 38

PIC. ADJ. 37 33 37 32

Others

Communications Example

This section shows the communication examples of RS-232C.

Operating command

Type Command Description

Connection check PC "

This unit: 21 89 01 00 00 0A

This unit " PC: 06 89 01 00 00 0A

Connection check

Power (On) PC "

This unit: 21 89 01 50 57 31 0A

This unit " PC: 06 89 01 50 57 0A

When power is turned on from the

Standby mode

Power (Off) PC "

This unit: 21 89 01 50 57 30 0A

This unit " PC: 06 89 01 50 57 0A

When power is turned off (Standby

mode) from power-on mode

Remote control

(MENU)

PC "

This unit: 21 89 01 52 43 37 33 32 45 0A

This unit " PC: 06 89 01 52 43 0A

When the same operation as

pressing the [MENU] button on the

remote control is performed

Reference command

Type Command Description

Power (On) PC "

This unit: 3F 89 01 50 57 0A

This unit " PC: 06 89 01 50 57 0A

This unit " PC: 40 89 01 50 57 31 0A

When information on the power-on

state is acquired

Input (HDMI 1) PC " This unit: 3F 89 01 49 50 0A

This unit " PC: 06 89 01 49 50 0A

This unit " PC: 40 89 01 49 50 36 0A

When information on HDMI 1 input

is acquired

Others

Specifications

Product Name D-ILA Projector

Model Name DLA-RS600, DLA-RS500, DLA-RS400

Display Panel/Size D-ILA device *1, 2

0.7" (1920 x 1080 pixels) x 3 (total no. of pixels: approx. 6.22 million)

Projection Lens 2.0 x power zoom lens (1.4:1 to 2.8:1), motorized zoom and focus

Light-source Lamp 265 W ultra-high pressure mercury lamp [product no.: PK-L2615U]

Average lifespan: 4500 hours (“Low” mode)

Screen Size Approx. 60" to 200" (Aspect ratio of 16:9)

Brightness 1900 lm 7

1800 lm 8

1700 lm 9

Projection Distance Refer to P. 71.

Input Compatibility Signal Refer to P. 73.

Display Resolution 3840 x 2160 pixels *3

Input Terminal HDMI Input Dual, HDMI 19-pin x 2 (HDCP 2.2-compatible) *4

Output Terminal Trigger Terminal 1 system, Ø 3.5 mm DC Power Jack (E)

DC OUT 12 V, 0.1 A

3D synchro Dedicated terminal for 3D SYNCHRO EMITTER (1 system, mini-DIN

3-pin)

Control Terminal RS-232C Terminal 1 system, D-sub 9-pin (male) (external control)

LAN Terminal 1 system, RJ-45 plug

Power Requirements AC 100 V to 240 V, 50 Hz/60 Hz

Power Consumption 380 W (during networked standby: 1.5 W *5, during standby: 0.4 W *6)

Operation Environment Temperature: 5°C to 35°C; humidity: 20% to 80%; storage

temperature: -10°C to 60°C

Installation Height Below 5,000 ft (1524 m)

Dimensions (Width x Height x Depth) Approx. 455 mm x 179 mm x 472 mm (excluding feet and protrusions)

Mass 15.6 kg (7 8)

15.4 kg (9)

Accessories Refer to P. 9.

*1 D-ILA is the abbreviation for Direct drive Image Light Amplifier.

*2 D-ILA

devices are manufactured using extremely high-precision technology with a pixel effectiveness of 99.99%.

Only 0.01% or less of the pixels are either missing or would remain permanently lit.

*3 During 3D playback, the pixel is set to 1920 x 1080.

*4 HDCP is the abbreviation for High-bandwidth Digital Content Protection system. The image of the HDMI input

terminal may not be displayed in some cases due to changes in the HDCP specifications.

*5 The power consumption of this product during networked standby when all wired network ports are connected

is 1.5 W.

*6 “During standby” refers to Eco Mode standby (P. 55).

Design and specifications are subject to change without prior notice.

Please

note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in order

to aid comprehension. Images may differ from the actual product.

Others

For 7 8, a “THX 3D Display Certification” by THX has been obtained.

In addition to 2D movies, you can also enjoy faithful reproduction of images in a “quality as

intended by the filmmaker” during playback of 3D movies.

The THX 3D certification is “an indication of high definition and high resolution”, which is

granted to products that have cleared more than 400 image quality tests.

7 8 are isf-certified, so calibration can be performed by an isf-certified trainer.

After calibration is performed, an isf mode is added to the Picture mode.

For more details, please refer to the isf website.

http://www.imagingscience.com/

About Trademarks and Copyrights

HDMI, HDMI logo and High-Definition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LCC.

“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation

Screen Size and Projection Distance

When a 16:9 screen is used

Screen Size Projection Distance

Diagonal (Model) Width (mm) Height (mm) Wide-end (m) Tele-end (m)

60 1328 747 1.78 3.66

70 1549 872 2.09 4.28

80 1771 996 2.4 4.89

90 1992 1121 2.7 5.51

100 2214 1245 3.01 6.13

110 2435 1370 3.31 6.75

120 2656 1494 3.62 7.36

130 2878 1619 3.92 7.98

140 3099 1743 4.23 8.60

150 3320 1868 4.53 9.22

160 3542 1992 4.84 9.84

170 3763 2117 5.14 10.45

180 3984 2241 5.45 11.07

190 4206 2366 5.75 11.68

200 4427 2490 6.06 12.30

Others

When a 4:3 screen is used

Screen Size Projection Distance

Diagonal (Model) Width (mm) Height (mm) Wide-end (m) Tele-end (m)

60 1219 914 2.22 4.49

70 1422 1067 2.60 5.24

80 1626 1219 2.98 6.00

90 1829 1372 3.36 6.75

100 2032 1524 3.74 7.51

110 2235 1676 4.11 8.26

120 2438 1829 4.49 9.02

130 2642 1981 4.87 9.77

140 2845 2134 5.25 10.53

150 3048 2286 5.63 11.28

160 3251 2438 6.00 12.04

* Projection to a 4:3 screen larger than 163" is equivalent to a size that is larger than 200" in the 16:9 format, and is

beyond our guarantee coverage.

When a 2.35:1 screen is used

Screen Size Projection Distance

Diagonal (Model) Width (mm) Height (mm) Wide-end (m) Tele-end (m)

60 1402 597 1.95 3.91

70 1636 696 2.28 4.56

80 1870 796 2.60 5.21

90 2103 895 2.93 5.86

100 2337 995 3.26 6.51

110 2571 1094 3.58 7.16

120 2805 1193 3.91 7.81

130 3038 1293 4.23 8.47

140 3272 1392 4.56 9.12

150 3506 1492 4.88 9.77

160 3740 1591 5.21 10.42

170 3973 1691 5.53 11.07

180 4207 1790 5.86 11.72

190 4441 1890 6.19 12.37

200 4674 1989 6.51 13.02

Others

Types of Possible Input Signals

Video

Digital Video Signal 480p, 576p, 720p/50 Hz, 720p/60 Hz, 1080i/50 Hz, 1080i/60 Hz, 1080p/24

Hz, 1080p/50 Hz, 1080p/60 Hz, 3840×2160/24Hz, 3840×2160/25Hz,

3840×2160/30Hz, 3840×2160/50Hz*1, 3840×2160/60Hz*1,

4096×2160/24Hz*2, 4096×2160/25Hz*2, 4096×2160/30Hz*2,

4096×2160/50Hz*1, 2, 4096×2160/60Hz*1, 2

3D Signal Frame Packing 720p/50 Hz, 720p/60 Hz, 1080p/24 Hz

Side-by-side 1080i/60 Hz, 1080p/60 Hz, 1080i/50 Hz, 1080p/50 Hz, 1080p/24 Hz,

720p/50 Hz, 720p/60 Hz

Top-and-bottom 720p/50 Hz, 720p/60 Hz, 1080p/24 Hz

*1 When the color space is RGB/YCbCr(4:4:4), only 8-bit input is supported.

The display image when the input signal is 4096×2160

4096

3840

2160

Display Area

PC signal (HDMI)

No. Designation Resolution fh [kHz] fv [Hz]

dot CLK

[MHz]

Total No.

of Dots

[dot]

Total No.

of Lines

[line]

No. of

Effective

Dots [dot]

No. of

Effective

Lines

[line]

1 VGA 60 640×480 31.500 60.000 25.200 800 525 640 480

2 VGA 59.94 640×480 31.469 59.940 25.175 800 525 640 480

3 SVGA 60 800×600 37.879 60.317 40.000 1,056 628 800 600

4 XGA 60 1024×768 48.363 60.004 65.000 1,344 806 1,024 768

5 WXGA 60 1280×768 47.760 60.000 79.998 1,675 796 1,280 768

6 WXGA+ 60 1440×900 55.919 59.999 106.470 1,904 932 1,440 900

7 SXGA 60 1280×1024 63.981 60.020 108.000 1.688 1,066 1,280 1,024

8 WSXGA+ 60 1680×1050 65.222 60.002 147.140 2,256 1,087 1,680 1,050

* Even

when signals can be input, video images may not be projected properly depending on the PC or cable in use.

When this occurs, switching to another compatible resolution or changing the cable may help to resolve the problem

in some cases.

Others

Indicator Display on the Main Unit

Meaning of the lighting figures

The indicator appears blinking.

The indicator lights up.

LAMP WARNING

STANDBY/ON

Operation mode display

Displays using the different colors and solid/blinking light of the “STANDBY/ON” indicator.

LAMP WARNING

STANDBY/ON

TAN

DBY

LAMP WARNING

STANDBY/ON

TAN

DBY

LAMP WARNING

STANDBY/ON

LAMP

WARNING

STANDBY/ON

TANDBY

LAMP WARNING

STANDBY/ON

TANDBY

When the video image is temporarily hidden (HIDE is on)

During projection

All lights off

In the Cool-down mode

“STANDBY/ON” blinking (red)

During lamp startup

“STANDBY/ON” lights up (green)

In standby state

“STANDBY/ON” lights up (red)

“STANDBY/ON” blinking (green)

Estimated timing for lamp replacement

Displays using the solid/blinking light of the “LAMP” indicator. The “STANDBY/ON” indicator, which shows the operating

mode of the unit, is displayed simultaneously as described above.

LAMP WARNING

STANDBY/ON

“LAMP” lights up (orange)

When lamp replacement is

near

Others

Warning display

You can tell the details of a warning from the (repeated) displays of the “WARNING” and “LAMP” indicators. The

“STANDBY/ON”

indicator, which shows the operating mode of the unit, is displayed simultaneously as described above.

The Warning mode is activated once the message is displayed. Projection is interrupted, and the cooling fan is turned

on for about 100 seconds.

The power cannot be turned on again while cooling is in progress. Check the following after cooling is complete.

Indicator Status (Solid/Blinking)

Blinking

Frequency

Description Check and Countermeasure

LAMP WARNING

STANDBY/ON

WARNING

(Red)(*)Mode

Display

x1 Abnormality in the power supply

Check that nothing is blocking

the air inlets.

Check that the external

temperature is normal.

Countermeasure: Leave the unit

unoperated until it cools down.

After

that, turn on the power again.

x2 Cooling fan stopped abnormally

x3 Internal temperature is abnormally

high

x4 External temperature is too high

x5 Abnormal circuit operation

LAMP WARNING

STANDBY/ON

WARNING

LAMP

Blinking

Simultaneously

(Red)

(Orange)

Mode

Display

x1 Abnormal circuit operation

x4 Abnormal operation of the lens

cover

Check that nothing is blocking

the lens cover.

Countermeasure: Turn on the

power again.

LAMP WARNING

STANDBY/ON

LAMP

WAR

NING

(Red)

(Orange)

Mode

Display

x1 Lamp does not light up and unit is

unable to project

Check that the lamp unit and

lamp cover are correctly

installed.

Countermeasure: Turn on the

power again.

x2 Lamp goes out during projection

x3 When the lamp cover is removed

If the Warning mode is activated again, wait for the cooling fan to stop, followed by pulling out the power plug from the

outlet.

Request for repair at your authorized dealer or a nearby service center.

(*) If the scheduled time for lamp replacement is exceeded, the indicator may light up.

Others

Dimensions

(Unit: mm)

Top Surface

472

455

Lens

Front

Ø60

103.5

178.5

227.5

Lens Center

Bottom Surface

33759

91 290

Lens

Rear Surface

92110

32 110

Lamp Cover

The dimensions are identical for all the models.

Others

Index

Accessories ........................................................... 9

Adjusting Distortion of the Projection Screen

....... 23

Adjustment and Setting by the Menu ................... 41

Adjustment of the Image Quality .......................... 43

ADVANCED MENU ............................................. 13

Anamorphic ......................................................... 50

Aspect ................................................................. 27

Back Color ........................................................... 54

Brightness ............................................................ 45

Ceiling Mount ....................................................... 16

Cleaning and Replacing the Filter

........................ 60

Clear Black .......................................................... 43

Clear Motion Drive ............................................... 39

Color Density ....................................................... 46

Color Management .............................................. 33

COLOR P.FILE .................................................... 31

Color Profile ......................................................... 31

Color Shade ......................................................... 46

Color Space ......................................................... 46

Color Temperature ............................................... 44

Connection .......................................................... 18

Contrast ............................................................... 45

Controls and Features ......................................... 10

Custom Gamma ................................................... 37

Dimensions .......................................................... 76

Display Position

................................................... 47

Eco Mode ............................................................ 55

External Control ...................................................

Filter Product no. ................................................. 60

Filter Replacement

............................................... 60

Focus ................................................................... 24

Frame Interpolation .............................................. 39

Frame Packing ..................................................... 29

GAMMA ............................................................... 36

Gamma Adjustment

............................................. 36

HDMI Color Space ............................................... 46

HDMI Input Level

................................................. 46

HDMI Input Terminal ............................................ 18

HIDE .................................................................... 21

High Altitude Mode .............................................. 50

Indicator Display .................................................. 74

INFO ....................................................................

Input Resolution ............................................. 56, 73

Input Signal .................................................... 56, 73

Input terminals .....................................................

Installation Method .............................................. 15

Installing the 3D Syncro Emitter ........................... 28

Keystone Correction ............................................ 50

Lamp ..................................................................... 9

Lamp Power

......................................................... 43

Lamp Time ........................................................... 56

Language Selection ............................................. 54

Lens ..................................................................... 10

LENS AP. ............................................................. 13

Lens Aperture ................................................ 40, 43

Lens Control ........................................................ 23

Lens cover ........................................................... 10

Lens Cover ............................................................ 9

Lens Memory ....................................................... 23

Lens Shift ............................................................. 23

Line Display ......................................................... 54

Logo Display ........................................................ 54

Menu Items .......................................................... 41

Menu Position

...................................................... 54

MPC LEVEL ......................................................... 34

Network ............................................................... 55

NR .......................................................................

Off Timer .............................................................. 54

Optional Accessories

............................................. 9

P.ANALYZER ...................................................... 13

PIC. ADJ.

............................................................. 45

Picture Mode ....................................................... 30

Picture Tone ........................................................ 44

Pixel Adjustment .................................................. 49

Precautions during Installation ............................. 15

Progressive .......................................................... 47

Projection Distance .............................................. 71

Remote Control ................................................... 13

Replacing the Lamp

............................................. 57

Resetting the Lamp .............................................. 56

RGB ..................................................................... 46

RS-232C .............................................................. 19

Screen Correction ................................................ 26

Screen Mask

........................................................ 47

Screen Size and Projection Distance ................... 71

Shadow/Highlight Correction ............................... 38

Shift ..................................................................... 24

Others

Side by Side ........................................................ 29

Signal Display

...................................................... 56

Software Ver. ....................................................... 56

Specifications ...................................................... 70

THX ..................................................................... 71

Top and Bottom

................................................... 29

Trigger ................................................................. 54

Troubleshooting ................................................... 61

User Name Edit ................................................... 43

Viewing 3D Movies .............................................. 28

Viewing Videos

.................................................... 21

When the following messages appear... .............. 65

Zoom ................................................................... 24

Symbol

3D Crosstalk Cancel ............................................ 29

3D Format ............................................................

3D Glasses ...................................................... 9, 28

3D Setting ............................................................ 47

3D Synchro Emitter .......................................... 9, 28

Others

DLA-RS600

DLA-RS500

DLA-RS400

D-ILA PROJECTOR

JVC DLA-RS600E Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van JVC DLA-RS600E

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info