56684
14
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
MICRO COMPONENT SYSTEM
UX-S15—Consists of CA-UXS15 and SP-UXS15
INSTRUCTIONS
LVT1736-001A
[B]
E
n
g
l
i
s
h
COVER.FM Page 1 Monday, May 21, 2007 10:33 AM
G-1
Warnings, Cautions and Others
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1 Do not remove screws, covers or cabinet.
2 Do not expose this appliance to rain or moisture.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instrument.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
CAUTION
Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get
out.)
Do not place any naked flame sources, such as lighted
candles, on the apparatus.
When discarding batteries, environmental problems must
be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION –– % (standby/on) button!
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off). When installing the apparatus
ensure that the plug is easily accessible. The
%
(Standby/on)
button in any position does not disconnect the mains line.
When the system is on standby, the STANDBY lamp lights
red.
When the system is turned on, the STANDBY lamp goes
off.
The power can be remote controlled.
CAUTION
Excessive sound pressure from earphones or headphones
can cause hearing loss.
SAFETY.FM Page 1 Thursday, April 19, 2007 11:38 AM
G-2
Information for Users on Disposal of Old Equipment
Dear Customer,
This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and
electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technology Centre Europe GmbH
Postfach 10 05 52
61145 Friedberg
Germany
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm
or more.
[European Union]
This symbol indicates that the electrical and electronic equipment should not be disposed as general
household waste at its end-of-life. Instead, the product should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment for proper treatment, recovery
and recycling in accordance with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources and will help prevent
potential negative effects on the environment and human health which could otherwise be caused by
inappropriate waste handling of this product. For more information about collection point and recycling
of this product, please contact your local municipal office, your household waste disposal service or the
shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page www.jvc-europe.com
to obtain
information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable national legislation or
other rules in your country for the treatment of old electrical and electronic equipment.
Attention:
This symbol is only
valid in the
European Union.
15 cm
15 cm
Front view Side view
SP-UXS15
CA-UXS15
SP-UXS15
CA-UXS15
SAFETY.FM Page 2 Thursday, April 19, 2007 11:38 AM
G-3
IMPORTANT for the U.K.
DO NOT
cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
BE SURE
to replace the fuse only with an identical approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow the instructions given below:
IMPORTANT:
DO NOT
make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green
or green-and-yellow.
The wires in the mains lead on this product are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
SAFETY.FM Page 3 Thursday, April 19, 2007 11:38 AM
G-4
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any
electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and
withdraw the mains plug when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in
any way—switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of
traffic safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case
—this could result in a fatal electrical shock.
NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
SAFETY.FM Page 4 Thursday, April 19, 2007 11:38 AM
1
Contents
Introduction ........................................................2
Precautions ......................................................................... 2
How to Read This Manual ................................................. 3
Getting Started ...................................................4
Step 1: Unpack ................................................................... 4
Step 2: Prepare the Remote Control .................................. 4
Step 3: Hook Up ................................................................ 5
Before Operating the System ............................7
Daily Operations—Playback .............................8
Listening to the Radio ........................................................ 9
Playing Back a Disc ......................................................... 10
Playing Back a Tape ........................................................ 10
Daily Operations—Sound & Other
Adjustments ......................................................11
Adjusting the Volume ...................................................... 11
Adjusting the Sound ........................................................ 11
Setting the Clock ............................................................. 12
Turning Off the Power Automatically ............................. 12
Advanced Radio Operations ...........................13
Receiving FM Stations with Radio Data System ............ 13
Searching for a Program by PTY Codes .......................... 13
Switching Temporarily to a Program of Your Choice
Automatically ............................................................... 14
Advanced Disc Operations ............................15
Programming the Playing Order—Program Play ............ 15
Playing at Random—Random Play ................................. 16
Playing Repeatedly—Repeat Play ...................................17
Advanced Tape Operations .............................18
Recording on a Tape ........................................................ 18
Synchronized Disc Recording ......................................... 19
Timer Operations .............................................20
Setting the Timer ............................................................. 20
Additional Information ...................................22
Learning More about This System .................................. 22
Troubleshooting ............................................................... 23
Maintenance ..................................................................... 24
Specifications ................................................................... 24
Parts Index ....................................................................... 25
UX-S15[B].BOOK Page 1 Monday, May 21, 2007 10:30 AM
2
Introduction
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to
ensure your complete understanding and to obtain the best
possible performance from the unit.
Precautions
Installation
Install in a place which is level, dry and neither too hot nor
too cold—between 5°C and 35°C.
Install the System in a location with adequate ventilation to
prevent internal heat buildup inside the System.
Leave sufficient distance between the System and the TV.
Keep the speakers away from the TV to avoid interference
with TV.
Power sources
When unplugging the System from the wall outlet, always
pull on the plug, not the AC power cord.
Moisture condensation
Moisture may condense on the lenses inside the System in
the following cases:
After starting to heat the room
• In a damp room
• If the System is brought directly from a cold to a warm
place
Should this occur, the System may malfunction. In this case,
leave the System turned on for a few hours until the moisture
evaporates, unplug the AC power cord, then plug it in again.
Others
Should any metallic object or liquid fall into the System,
unplug the AC power cord and consult your dealer before
operating any further.
If you are not going to operate the System for an extended
period of time, unplug the AC power cord from the wall outlet.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
DO NOT install the System in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust or vibration.
DO NOT handle the AC power cord with wet
hands.
For safety, observe the following carefully:
Make sure there is good ventilation around
the main unit. Poor ventilation could
overheat and damage the System.
DO NOT block the ventilation openings or
holes. If they are blocked by a newspaper or
cloth, etc., the heat may not be able to get
out.
DO NOT disassemble the System since there
are no user serviceable parts inside.
UX-S15[B].BOOK Page 2 Monday, May 21, 2007 10:30 AM
3
How to Read This Manual
To make this manual as simple and easy-to-understand as
possible, we have adapted the following methods:
Button and control operations are explained as listed in the
table below. In this manual, the operations using the
remote control is mainly explained; however, you can use
the buttons and controls on the main unit if they have the
same (or similar) name and marks.
Some related tips and notes are explained later in the
sections “Learning More about This System” and
“Troubleshooting” , but not in the same section
explaining the operations.
If you want to know more about
the functions, or if you have a doubt about the functions, go
to these sections and you will find the answers.
Indicates that you press the button
briefly
.
Indicates that you press the button
briefly and repeatedly
until an option
you want is selected.
Indicates that you press one of the
buttons.
Indicates that you
press and hold
the
button for specified seconds.
The number inside the arrow
indicates the period of press (in this
example, 2 seconds).
If no number is inside the arrow,
press and hold until the entire
procedure is complete or until you
get a result you want.
Indicates that you push the button to
adjust volume level.
Indicates that this operation is only possible
using the remote control.
Indicates that this operation is only possible
using the buttons and controls on the main
unit.
2 sec.
Remote
ONLY
Main Unit
ONLY
UX-S15[B].BOOK Page 3 Monday, May 21, 2007 10:30 AM
4
Getting Started
Step 1: Unpack
After unpacking, check to be sure that you have all the
following items. The number in parentheses indicates the
quantity of each piece supplied.
• FM antenna (1)
AM loop antenna (1)
Remote control (1)
•Batteries (2)
If any item is missing, consult your dealer immediately.
Step 2: Prepare the Remote Control
Insert the batteries into the remote control by matching the
polarity (+ and –) correctly.
If the range or effectiveness of the remote control
decreases, replace both batteries.
FM
COAXL
75
AM
LOOP
AM EXT
ANTENNA
Step 1:Unpack the package and
check the accessories.
Step 2: Prepare the remote control.
Step 3: Hook up the components such
as AM/FM antennas, speakers,
etc. (see pages 5 to 6).
Finally plug the AC power cord.
Now you can operate the System.
Caution
Battery shall not be exposed to excessive heat such as
sunshine, fire or the like.
3
2
1
R03(UM-4)/AAA(24F)
UX-S15[B].BOOK Page 4 Monday, May 21, 2007 10:30 AM
5
Step 3: Hook Up
If you need more detailed information, see page 6.
Turn the power off to all components before connections.
To a wall outlet
Plug the AC power cord only after all connections are complete.
FM antenna (supplied)
Extend it so that
you can obtain the
best reception.
Red
Black
AM loop antenna (supplied)
Turn it until the best reception is
obtained.
UX-S15[B].BOOK Page 5 Monday, May 21, 2007 10:30 AM
6
To connect the AM loop antenna
Make sure to connect the wire correctly.
For better FM/AM reception
Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System,
connecting cords, and the AC power cord. This could cause
poor reception.
To connect the speaker cords
Make sure the both speakers are connected correctly and
firmly.
When connecting the speaker cords, match the polarity of
the speaker terminals: The black cord to (-), the red cord to
(+).
If the AM loop antenna wire or speaker cords are covered
with vinyl, remove the vinyl to expose the tip of the
antenna wire or speaker cords by twisting the vinyl.
1 Hold
2 Insert 3 Release
AM
LOOP
AM EXT
ANTENNA
FM
COAXL
75
AM loop antenna
Keep it connected.
Outdoor FM
antenna
(not supplied)
Vynile-covered wire (not supplied)
Extend it horizontally.
Disconnect the supplied FM antenna,
and connect to an outdoor FM antenna
using a 75 wire with coaxial type
connector (IEC or DIN45325).
• DO NOT connect more than one speaker to
each terminal.
DO NOT allow the conductor of the speaker
cords to be in touch with the metallic parts of
the System.
1 Unlock
2 Insert
3 Lock
UX-S15[B].BOOK Page 6 Monday, May 21, 2007 10:30 AM
7
Before Operating the System
The indications on the display teach you a lot of things while you are operating the System.
Before operating the System, be familiar with when and how the indicator illuminates on the display.
1 REPEAT mode indicator
Lights when Repeat Play mode is activated.
2 TRACK indicator
Audio disc: Lights during playback and stop.
MP3/WMA disc: Lights during playback.
3 GROUP indicator
MP3/WMA disc: Lights during stop.
4 MP3/WMA indicator
Lights when MP3/WMA disc is detected.
5 RANDOM indicator
Lights when Random Play mode is activated.
6 CD indicator
Lights when Audio disc is detected.
7 E indicator
3: Lights when disc or tape is playing.
8: Lights when disc or tape is paused.
8 PROG. (Program) indicator
Lights when preset station is selected.
Lights when Program Play mode is activated.
9 Tape operation indicator
Lights when TAPE is selected.
Ö REC: Lights when recording is progressing.
p NEWS/INFO indicator
NEWS/INFO: Lights to indicate the currently selected
program type for PTY Standby Reception.
NEWS/INFO: Flashes when a program is automatically
tuned in with PTY Standby Reception.
q SLEEP indicator
Lights when the Sleep Timer is activated.
w HBS indicator
Lights when HBS (Hyper Bass Sound) mode is
activated. (see page 11)
e SOUND MODE indicator
Lights the selected sound mode. (see page 11)
r FM reception indicator
MONO: Lights while the FM monaural mode is activated.
ST: Lights while
FM
stereo station with sufficient signal
strength is tuned in.
t Frequency indicators
Lights when frequency is detected.
y TIMER indicator
: Lights when Daily Timer stands by; flashes while
working.
TRACK CD
TRACK
MP3
PROG.
MHz
kHz
TRACK CD
While listening to radio:
Band
Frequency
While disc play is stopped:
Total track number
Total playing time
Track number
in current group
Elapsed
playing time
CD:
MP3/WMA:
While playing a CD:
Indications on the main display
While playing an MP3:
MP3
GROUP
Total group number Total track number
While MP3/WMA disc play is stopped:
SLEEP
REPEAT1
TRACK
TAPE REC
WMA MP3 CD
GROUP RANDOM PROG. NEWS INFO
HBS JAZZ POPROCK CLASSIC MONOST
MHz
kHz
62 54 8731
11 12 13
109
161514
Track number Elapsed
playing time
TAPE
While playing a tape:
Both MP3 and WMA indicators are displayed when
both formats contain in one disc. Otherwise each
format indicator is displayed.
Body.fm Page 7 Thursday, July 5, 2007 4:52 PM
8
Daily Operations—Playback
1 Turn on the power.
The STANDBY lamp on the main unit turns off.
2 Select the source.
Playback automatically starts if the selected source is
ready to start.
If you press TAPE, only the source will be selected.
3 Adjust the volume.
4 Operate the target source as explained
later.
To turn off (standby) the System
How to Select Numbers
2
1
3
4
VOLUME
2
1
3
TRACK CD
FM/AMCD TAPE
DISPLAY/
PROGRAM
Numeric
buttons
TUNING/
GROUP/PTY
4/1/
Á/¢
PRESET
STOP 7
The STANDBY lamp on the main unit
lights up.
A small amount of power is always
consumed even while on standby.
For private listening
Connect a pair of headphones to the PHONES jack on the
main unit. The sound will no longer come out of the
speakers. Be sure to turn down the volume before
connecting or putting the headphones.
Disconnecting the headphones will activate the
speakers again.
DO NOT turn off (stand by) the System with
the volume set to an extremely high level;
otherwise, the sudden blast of sound can
damage your hearing, speakers and/or
headphones when you turn on the System or
start playback.
Examples:
To select number 5, press 5.
To select number 15, press 10
1 5.
To select number 30, press 10
3 0.
To select number 125, press
10 twice 1 2 5.
=
>
=
>
=
>
UX-S15[B].BOOK Page 8 Monday, May 21, 2007 10:30 AM
9
Listening to the Radio
To select the band (FM or AM)
You can also carry out the same operation using the FM/AM
on the System.
To tune in to a station
While FM or AM is selected...
Frequency starts changing on the display.
When a station (frequency) with sufficient signal strength is
tuned in, the frequency stops changing.
When you repeatedly press the button, the frequency
changes step by step.
To stop searching manually,
press either button.
If the received FM station is hard to listen
Select “FM MONO”
To preset the stations
You can preset 20 FM and 10 AM stations.
1 Tune in to a station you want to preset.
2 Activate the preset number entry mode.
Finish the following process while the indication on the
display is flashing.
3 Select a preset number for the station you store.
How to Select Numbers, see page 8.
You can also use the 4/¢ .
4 Store the station.
To tune in to a preset station
1 Select a band (FM or AM).
2 Select a number of the preset station you stored.
How to Select Numbers, see page 8.
You can also use the 4/¢ .
Remote control: Main unit:
FM
MONO:
Reception will improve though stereo
effect is lost. MONO indicator lights up.
FM/AM
FM FM MONO
AM
TUNING/GROUP/PTY
1 sec.
1 sec.
FM/AM
FM FM MONO
AM
PROG.
MHz
kHz
FM/AM
FM FM MONO
AM
Playable media and files
This system can playback following types of media and
files.
This system may not playback some files even though
their formats are listed above.
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
Media Audio CD, CD-R/RW
File format MP3, WMA
Audio CD CD-R CD-RW
UX-S15[B].BOOK Page 9 Monday, May 21, 2007 10:30 AM
10
Playing Back a Disc
To insert a disc
You can insert discs while playing another source.
To select a track/group
To select a track:
To select a group (MP3/WMA disc only):
To locate a particular portion
While playing a disc, press and hold until the portion you
want is reached.
No sound is played during this operation on MP3 sources.
To locate a track directly and
start play
How to Select Numbers, see page 8.
• When you play MP3/WMA disc, the selectable tracks by
using numeric keys are limited to a current group.
To display ID3 tag
While playing MP3/WMA disc.
When “ID3 ON” is set, ID3 tag is displayed after the source
is indicated.
Playing Back a Tape
To insert a tape
You can play back type I tapes.
Select the source “TAPE”.
To start: To pause: To stop:
To release, press again.
Main Unit
ONLY
CD CD
STOP
Decreases the track numbers.
Increases the track numbers.
Decreases the group numbers.
Increases the group numbers.
Fast-forwards the track.
Fast-reverses the track.
To start: To pause: To stop:
To rewind tape:
Remote
ONLY
DISPLAY/
PROGRAM
ID3 ON
ID3 OFF
With the tape side facing down
Push Insert Close
TA P E
TA P E TA P E
STOP
Wind forward the tape.
Rewind the tape.
UX-S15[B].BOOK Page 10 Monday, May 21, 2007 10:30 AM
11
Daily Operations—Sound & Other Adjustments
Adjusting the Volume
You can adjust the volume level from level 0 (VOL MIN) to
level 31 (VOL MAX).
To drop the volume in a moment
Adjusting the Sound
To reinforce the bass sound—HBS
You can enjoy powerful bass sound with the Hyper-Bass
Sound effect.
Sound Mode
You can select one of 4 SEA (Sound Effect Amplifier)
modes. You can use this effect only for playback.
Remote control
CLOCK/
SLEEP
SOUND
MODE
FADE
MUTING
VOLUME
+/–
HBS
Main unit
CLOCK/
SLEEP
VOLUME
+/–
4
/
¢
4
/
¢
CLOCK/
SLEEP
Remote control: Main unit:
To restore the volume,
press again, or
adjust the volume level.
ROCK Boosts low and high frequencies.
POP Good for vocal music.
CLASSIC Good for classical music.
JAZZ Accented lower frequencies for jazz-
type music.
No
indication
No sound effect applies.
Remote
ONLY
FADE
MUTING
Remote
ONLY
HBS
(No indication)
HBS
Canceled
SOUND MODE
ROCK
POP
CLASSIC
JAZZNo indication
(No sound effect)
UX-S15[B].BOOK Page 11 Monday, May 21, 2007 10:30 AM
12
Setting the Clock
Without setting the built-in clock, you cannot use the Daily
Timer (see page 20).
1 Turn off (standby)
2 Activate the clock setting mode.
3 Adjust the hour.
4 Adjust the minute.
The built-in clock starts working.
To check the current time during play
If there is a power failure
The clock loses its settings and blinks. You need to set the
clock again.
Turning Off the Power Automatically
To turn off the System after a certain period of
time—Sleep Timer
1 Activate the sleep timer mode.
2 Specify the time (in minutes).
Sleep timer requires a few seconds to set. The system
automatically turns off when the selected count down
time is executed.
To check the time remaining until the shut-off time
CLOCK/
SLEEP
5 sec.
SLEEP
REPEAT1
TRACK WMA
GROUP
HBS JAZZ
CLOCK/
SLEEP
Clock
Source information
CLOCK/
SLEEP
2 sec.
SLEEP
10 20 30 40 50
90 80 70 60
(Canceled)
OFF
CLOCK/
SLEEP
SLEEP
2 sec.
Body.fm Page 12 Thursday, July 5, 2007 4:52 PM
13
Advanced Radio Operations
Receiving FM Stations with
Radio Data System
Radio Data System allows FM stations to send an additional
signal along with their regular program signals.
When tuned to an FM station which provides the Radio
Data System service.
This System can receive the following types of Radio Data
System signals.
To show the Radio Data System information
While listening to an FM station...
Searching for a Program by
PTY Codes
You can locate a particular kind of program from the preset
channels (see page 9) by specifying the PTY codes.
To search for a program using the PTY codes
1 While listening to an FM station...
2 Select a PTY code.
See Additional Information about PTY codes (See
page 22).
PS (Program
Service)
Shows commonly known
station names.
PTY (Program
Type)
Shows types of broadcast
programs.
RT (Radio Text)
Shows text messages the station
sends.
Enhanced Other
Networks
Provides the information about
the types of the programs
broadcast by the Radio Data
System stations of the different
networks.
Remote control
TUNING/
GROUP/PTY
PTY
SEARCH
DISPLAY
MODE
NEWS/INFO
Remote
ONLY
PS Station names is displayed. “NO PS” will
appear if no signal is sent.
PTY The broadcast program type is displayed. “NO
PTY” will appear if no signal is sent.
RT Text messages the station sends is displayed.
“NO RT” will appear if no signal is sent.
DISPLAY
MODE
Station Frequency
PS PTY RT
Remote
ONLY
UX-S15[B].BOOK Page 13 Monday, May 21, 2007 10:30 AM
14
3 Start searching.
The receiver searches 20 preset FM stations, stops when
it finds the one you have selected, and tunes in to that
station.
If no program is found, “NO FOUND” appear on the
display.
• To stop searching any time during search, press PTY
SEARCH.
To continue searching after it stops on an unwanted
station
While the indications on the display are flashing, press PTY
SEARCH again.
Switching Temporarily to a Program of
Your Choice Automatically
The Enhanced Other Networks function allows the System
to switch temporarily to a preset FM station broadcasting a
program of your choice (NEWS or INFO).
This function works while listening to an FM station
providing the required signals.
While listening to an FM station, select one of the
following:
NEWS News
INFO Program the purpose of which is to impart
advice in the widest sense
CD
Remote
ONLY
NEWS/INFO
(Canceled)
NEWS INFO
OFF
How the Enhanced Other Networks function actually
works:
CASE 1
If a station is not broadcasting the program of your
choice
The System continues tuning in to the current station.
Ç
When a station broadcasting the program of your choice,
the System automatically switches to the station.
NEWS/INFO indicator starts flashing.
Ç
When the program is over, the System goes back to the
previously tuned station, but the function still remains
active (the indicator stops flashing and remains lit).
CASE 2
If the station currently tuned in is broadcasting the
program of your choice
NEWS/INFO indicator starts flashing.
Ç
When the program is over, the indicator stops flashing (the
function still remains active).
UX-S15[B].BOOK Page 14 Monday, May 21, 2007 10:30 AM
15
Advanced Disc Operations
Programming the Playing Order—
Program Play
You can arrange the playing order of the tracks (up to 32)
before you start playback.
You can repeat one programmed track or all the programmed
tracks by pressing REPEAT.
1 Before starting playback, press DISPLAY/
PROGRAM.
2 Select tracks you want for Program Play.
How to Select Numbers, see page 8.
You can also use the 4/¢ .
For CD
For MP3/WMA
Press TUNING/GROUP/PTY to select a group, then
select a track.
Next program step will be indicated when you program
tracks on MP3/WMA disc.
3 Repeat step 2 to program the other tracks.
Remote control
CD 6
Numeric
buttons
RANDOM
DISPLAY/
PROGRAM
TUNING/
GROUP/PTY
4
/
¢
STOP 7
REPEAT
Main unit
CD 6
TUNING/
GROUP/PTY
4
/
¢
DISPLAY/
PROGRAM
STOP 7
MP3
PROG.
TRACK
CD
PROG.
For CD
For MP3/WMA disc
TRACK
CD
PROG.
Track number
Program step
MP3
GROUP
PROG.
Track number
Group number
MP3
PROG.
UX-S15[B].BOOK Page 15 Monday, May 21, 2007 10:30 AM
16
4 Start playback.
The tracks you have selected are played back in the order
you have programmed.
Tracks cannot be selected with the Numeric buttons during
Program Play.
To check the programmed contents
While the PROG. indicator is shown on the display and
before playback...
To modify the program
While the PROG. indicator is shown on the display and
before playback...
Playing at Random—Random Play
You can play back all the tracks on the disc at random.
1 Press RANDOM.
2 Start play back.
Playback starts in random order.
Random Play ends when all tracks are played.
Tracks cannot be selected with the Numeric buttons during
Random Play.
To exit from Random Play
While the RANDOM indicator is shown on the display...
To skip a track: To pause: To stop:
To release, press
again.
Edit:
1 Press DISPLAY/PROGRAM repeatedly until
displaying the programmed number you want to edit.
2 Repeat the step 2 on page 15.
To add step in the program:
1 Press DISPLAY/PROGRAM repeatedly until
displaying “--” on the display.
2 Repeat the step 2 on page 15.
To erase entire program:
Exit from Program mode at the same time.
All the programs are also erased under the following action:
open CD door, change other sources, turn off the unit.
CD
CD
STOP
DISPLAY/
PROGRAM
STOP
To skip a track: To pause: To stop:
To release, press
again.
Remote
ONLY
RANDOM
CD
CD
STOP
RANDOM
UX-S15[B].BOOK Page 16 Monday, May 21, 2007 10:30 AM
17
Playing Repeatedly—Repeat Play
You can repeat playback.
For CD:
During Random Play:
For MP3/WMA disc:
REPEAT1 Repeats the current track.
REPEAT
GROUP
Repeats all the tracks in the current
group.
REPEAT Repeats all the tracks. Repeats the
program.
Remote
ONLY
REPEAT
Canceled
(No indication)
REPEAT1
REPEAT
REPEAT
Canceled
(No indication)
REPEAT1
REPEAT
REPEAT GROUP
UX-S15[B].BOOK Page 17 Monday, May 21, 2007 10:30 AM
18
Advanced Tape Operations
Recording on a Tape
You can use type I tapes for recording.
To play a tape, see page 10.
1 Insert a recordable cassette.
2 Select and start playing the source—“FM,” “AM,” or
“CD” .
3 Start recording.
Lights REC indicator on the display.
On the main unit
Remote control
CD 6 STOP 7
TAPE 6
FM/AM
Main unit
CD 6 STOP 7
TAPE 6
FM/AM
REC
PUSH/
OPEN 0
IMPORTANT
It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or
video recording, broadcast or cable program and in
any literary, dramatic musical, or artistic work
embodied therein.
To stop recording:
With the tape side facing down.
Push Insert Close
STOP
Body.fm Page 18 Monday, June 11, 2007 4:47 PM
19
Synchronized Disc Recording
You can start and stop both disc playback and tape recording
at the same time.
To record the entire disc
1 Load a disc and insert a recordable cassette.
If the current playing source is not the CD player, press
CD 6, then 7.
2 Start recording.
On the main unit
3 Flip the cassette tape manually to the opposite side.
When the tape reaches the end before finishing
playback the disc, the tape will stop and the disc will
pause. Press REC after flipping the cassette tape to the
opposite side track.
When the disc playback finishes before reaching the
end of the tape, the tape will continue running. To stop
it, press STOP 7.
When you press REC while playing back the disc, the
current playing track will be started to record from its
beginning to the end.
To erase the recorded track, change the source to TAPE then
press REC.
If the beat is heard while recording
an AM broadcast
Select “1” or “2” to reduce the beat.
To record Program Play or Random Play
Select Program Play (and make a program: see page 15)
or Random Play (see page 16).
To protect your recording
Cassettes have two small tabs on the back to protect from
unexpected erasure or re-recording.
To protect your recording, remove these tabs.
To re-record on a protected tape, cover the holes with
adhesive tape.
Main Unit
ONLY
BEAT
1
CUT
2
On the back of the main unit
UX-S15[B].BOOK Page 19 Monday, May 21, 2007 10:30 AM
20
Timer Operations
Setting the Timer
Using Timer, you can wake up with music, etc.
You can set the Timer when the System turns on.
To exit from the timer setting, press 7 as required.
1 To activate the TIMER setting
2 Set On Time
1 Set hour
2 Set minutes
Remote control
TIMER
Main unit
CD 6
4
/
¢
STOP 7
TAPE 6
FM/AM
CD 6
STOP 7
TAPE 6
FM/AM
4
/
¢
TIMER
How Daily Timer actually works
Once the Daily Timer has been set, the timer ( )
indicator is lit on the display. Lights TIMER lamp on the
main unit. Daily Timer is activated at the same time
everyday until the timer is turned off manually.
When the on-time comes
The System turns on, tunes in to the specified station or
starts playing the specified source.
The sound level is gradually turned up until the last
time you listened to. (Maximum Vol.16)
While Timer is working, the timer ( ) indicator
flashes on the display.
The timer setting remains in memory until you change it.
Without canceling the Timer, you can change the
source or adjust the volume after Timer starts playback.
TIMER
MHz
TIMER
2 sec.
UX-S15[B].BOOK Page 20 Monday, May 21, 2007 10:30 AM
21
3 Set Off Time
1 Set Off Time setting.
2 Set time.
See the step 2 1, 2
You can not set On time and Off time on the same time
setting.
4 Select the playback source.
1 Select the source.
2 Select the playback source; CD”,TAPE” or
TUNER”.
When you select “TUNER”
–1 4/¢ Select “AM PRE” or “FM PRE”, then press
TIMER.
–2 4/¢ Select preset number, then press TIMER.
5 Set TIMER active
.
The Timer indicator lights on the display and TIMER
lamp on the main unit.
6 Set the System STANDBY.
To inactivate the TIMER.
When the System turns on.
The timer ( ) indicator on the display and the TIMER
lamp of the main unit go out.
When setting both SLEEP TIMER and DAILY TIMER,
the timer which turns the unit off earlier takes precedence.
TIMER
TIMER
TIMERCD TAPE FM/AM
TIMER
TIMER
UX-S15[B].BOOK Page 21 Monday, May 21, 2007 10:30 AM
22
Additional Information
Learning More about This System
Daily Operations—Playback (see pages 8 to 10)
Listening to the Radio:
If you store a new station into an occupied preset number, the
previously stored station in that number will be erased.
When you unplug the AC power cord or if a power failure
occurs, the preset stations will be erased in a few days. If this
happens, preset the stations again.
Playing Back a Disc:
This System cannot play “packet write” discs.
For MP3/WMA playback...
MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/file
configuration.)
Some MP3/WMA files cannot be played back and will be
skipped. This results from their recording processes and
conditions.
When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
This System can play back MP3/WMA files with the
extension code <.mp3/.wma> (regardless of the letter
case—upper/lower).
Some characters or symbols will not be shown correctly on
the display.
The maximum character number shown on the display is 30
(without the extension code) for files, and 30 for ID3 tag.
It is recommended that you make each MP3/WMA file at a
sampling rate of 44.1 kHz and at bit rate of 128 kbps.
This System can recognize a total of 511 tracks and 511
groups on an MP3/WMA disc. Those exceeding the
maximum number cannot be recognized.
If a folder does not include MP3/WMA tracks, they are
ignored.
Playing Back a Tape:
It is not recommended to use the C-120 or longer tapes.
These tapes easily jams in the pinch roller and capstan, and
may cause characteristic deterioration.
Daily Operations—Sound & Other Adjustments
(see pages 11 and 12)
Adjusting the Volume:
Be sure to turn down the volume before connecting or putting
the headphones.
Adjusting the Sound:
This function also affects the sound through the headphones.
Setting the Clock:
The clock blinks on the display until you set the clock.
The clock may gain or lose 1 to 2 minutes per month. If this
happens, reset the clock.
Advanced Radio Operations (see pages 13
and 14)
Descriptions of the PTY Codes
NEWS: News
AFFAIRS: Topical programs expanding on the current
news or affairs
INFO: Programs on medical service, weather
forecasts, etc.
SPORT: Sports events
EDUCATE: Educational programs
DRAMA: Radio plays
CULTURE: Programs on national or regional culture
SCIENCE: Programs on natural sciences and
technology
VARIED: Other programs like comedies or ceremonies
POP M: Pop music
ROCK M: Rock music
EASY M: Middle-of-the road music (usually called
easy listening)
LIGHT M: Light music
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE: Reports on commerce, trading, the Stock
Market, etc.
CHILDREN: Entertainment programs for children
SOCIAL: Programs on social activities
RELIGION: Programs dealing with any aspect of belief
or faith, or the nature of existence or ethics
PHONE IN: Programs where people can express their
views either by phone or in a public form
TRAVEL: Programs about travel destinations, package
tours, and travel ideas and opportunities
LEISURE: Programs concerned with recreational
activities such as gardening, cooking,
fishing, etc.
JAZZ: Jazz music
COUNTRY: Country music
1
1
2
3
10
11
12
4
5
6
7
8
9
01
01
02
03 04
05
MP3/WMA groups/tracks configuration
This System plays backMP3/WMA tracks as follows.
The play order in the figure is for MP3/WMA tracks on
the disc.
Group with its play order
MP3/WMA track with its play
order
Hierarchy
Level 1 Level 2 Level 3 Level 4 Level 5
ROOT
UX-S15[B].BOOK Page 22 Monday, May 21, 2007 10:30 AM
23
NATION M: Current popular music from another nation
region, in that country’s language
OLDIES: Classic pop music
FOLK M: Folk music
DOCUMENT:
Programs dealing with factual matters,
presented in an investigative style
TEST: Broadcasts for testing emergency broadcast
equipment or unit
ALARM: Emergency announcement
NONE: No program type, undefined program, or
difficult to categorize into particular types
Advanced Disc (see pages 15 to 17)
Programming the Playing Order—Program Play:
If you try to program a 32nd track, “FULL” appears on the
display.
While programming steps...
Your entry will be ignored if you have tried to program an item
number that does not exist on the disc (for example, selecting
track 14 on a disc that only has 12 tracks).
Advanced Tape Operations (see pages 18 and 19)
Recording on a Tape:
The recording level is automatically set correctly. Thus, you
can adjust the sound you are actually listening to without
affecting the recording level.
There is leader tape which cannot be recorded onto at the start
and end of cassette tapes. Thus, when recording CDs or radio
broadcasts, wind the leader tape first to ensure that the
recording will be made without any music part lost.
If you start recording with no cassette inserted, “NO TAPE”
appears on the display. If a protected tape has been inserted,
“PROTECT” appears.
Timer Operations (see pages 20 and 21)
When you unplug the AC power cord or if a power failure
occurs, the timer will be canceled. You need to set the clock
first, then the timer again.
You can not set On time and Off time on the same time setting.
Troubleshooting
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General:
Adjustments or settings are suddenly canceled before
you finish.
] There is a time limit. Repeat the procedure again.
Operations are disabled.
] The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power cord
and then plug it back in.
Reset the System if you don’t solve the problem.
Press and hold the RESET button on the rear of the Unit for
3 seconds with something having a sharp point, while the
AC power cord is plugged off.
Resetting causes the unit to restore its factory default
settings and results in all the settings made by the user being
deleted.
Unable to operate the System from the remote control.
] The path between the remote control and the remote sensor
on the System is blocked.
] Point it at the remote sensor on the front panel.
] Signals cannot reach the remote sensor.
Move closer to the System.
] The batteries are exhausted.
No sound is heard from the speakers.
] Speaker connections are incorrect or loose (see page 6).
] Headphones are connected (see page 8).
Radio Operations:
Hard to listen to broadcasts because of noise (see pages 4
to 6).
] Antennas connections are incorrect or loose.
] The AM loop antenna is too close to the System.
] The FM antenna is not properly extended and positioned.
Disc Operations:
The disc does not play.
] The disc is placed upside down. Place the disc with the label
side up.
The disc sound is discontinuous.
] The disc is scratched or dirty.
Timer Operations:
Daily Timer does not work.
] The System has been turned on when the on-time comes.
Timer starts working only when the System is turned off.
] There might have been a power failure. Set the clock first,
then the timer again.
“INVALID” is indicated on the display.
] Set the Off Time first (see page 21).
Sharp point
UX-S15[B].BOOK Page 23 Monday, May 21, 2007 10:30 AM
24
Maintenance
To get the best performance of the System, keep your discs,
and mechanism clean.
Handling discs
When removing the disc from its case, hold it at the edge while
pressing the center hole lightly.
Do not touch the shiny surface of the disc, or bend the disc.
Put the disc back in its case after use to prevent warping.
Be careful not to scratch the surface of the disc.
Avoid exposure to direct sunlight, temperature extremes, and
moisture.
To clean the disc:
Wipe the disc with a soft cloth in a straight line from center to
edge.
Handling cassette tapes
If the tape is loose in its cassette, take up the slack by inserting
a pencil in one of the reels and rotate it.
If the tape is loose, it may get stretched, cut, or caught in the
cassette.
Be careful not to touch the tape surface.
Avoid the following places to store the tape—in dusty places,
in direct sunlight or heat, in moist areas, on a TV or speaker,
or near a magnet.
To keep the best recording and playback sound quality
Use a cotton swab moistened with alcohol to clean the heads,
capstans, and pinch rollers.
Use a head demagnetizer (available at electronics and audio
shops) to demagnetize the heads (when the System turned off).
Cleaning the System
Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a dry
cloth.
Since the System may deteriorate in quality, it become
damaged or get its paint peeled off, be careful about the
following:
DO NOT wipe it with a hard cloth.
DO NOT wipe it strongly.
DO NOT wipe it with thinner or benzine.
DO NOT apply any volatile substance such as insecticides
to it.
DO NOT allow any rubber or plastic to remain in contact for
a long time.
Specifications
Amplifier section
Output Power: 5 W per channel, min. RMS,
driven into 4 at 1 kHz with no
more than 10% total harmonic
distortion. (IEC268-3)
Speakers/Impedance: 4 – 8
Tuner section
FM tuning range: 87.50 MHz – 108.00 MHz
AM (MW) tuning range: 522 kHz – 1 629 kHz
CD player section
Dynamic range: 60 dB
Signal-to-noise ratio: 60 dB
Wow and flutter: Immeasurable
Cassette deck section
Frequency response
Normal (type I): 125 Hz – 8 kHz
Wow and flutter: 0.35% (WRMS)
General
Power requirement: AC 230 V , 50 Hz
Power consumption: 26 W (at operation)
0.9 W (on standby)
Dimensions (approx.): 141 mm × 211 mm × 216 mm
(W/H/D)
Mass (approx.): 2.6 kg
Speakers
Type: 1-way Bass reflex
Speaker units: 10 cm cone × 1
Impedance: 4
Dimensions (approx.): 136 mm × 212 mm × 178 mm
(W/H/D)
Mass (approx.): 1.3 kg each
Supplied Accessories
See page 4.
Design and specifications are subject to change without notice.
UX-S15[B].BOOK Page 24 Monday, May 21, 2007 10:30 AM
25
Parts Index
Refer to the pages to see how to use the buttons and controls.
Remote control
10
14
11
8, 11
8, 15
9, 15
10, 15, 18
16
11
11
13
17
9, 10, 13
8, 12
9
13–14
10
10, 12, 15
12
20
UX-S15[B].BOOK Page 25 Monday, May 21, 2007 10:30 AM
26
Main unit
8 12
20
10, 12, 15
23
10
11
7
9
10, 15, 18
10, 18
12
10
10
8, 23
9–10, 13
18
9
UX-S15[B].BOOK Page 26 Monday, May 21, 2007 10:30 AM
0707NYMCREMTS
EN
© 2007 Victor Company of Japan, Limited
UX-S15 MICRO COMPONENT SYSTEM
COVER.FM Page 2 Thursday, July 5, 2007 4:58 PM
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JVC CA-UXS15 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JVC CA-UXS15 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van JVC CA-UXS15

JVC CA-UXS15 Gebruiksaanwijzing - Nederlands, Deutsch, Français - 84 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info