700459
10
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
10 | JL Audio - XD400/4v2 Owners Manual
Note: When the “Input Voltage” switch is in its
“Low position, the level of the “Preouts” signals
matches the input signal levels (unity gain). When
the “Input Level” switch is in the “high” position,
the level of the input signal is attenuated –12 dB
to produce a line level signal at the “Preouts”.
This ensures a proper line level signal output
under both conditions.
If you plan to use the “Preouts” to feed a stereo
amplifier, you must connect a stereo signal to
the input of the amplifier. A mono signal into
the amplifier will result in a mono signal out of
the preamp output.
SPEAKER OUTPUTS
The XD400/4v2’s speaker outputs are designed
to accept 16 AWG - 8 AWG wire. To connect the
speaker wires to the amplifier, first back out the
set screws on the top of the terminal block, using
the supplied 2.5 mm hex wrench. Strip 1/2 inch
(12 mm) of insulation from the end of each wire
and insert the bare wire into the terminal block,
seating it firmly so that no bare wire is exposed.
While holding the wire in place, tighten the set
screw firmly, taking care not to strip the head of
the screw.
Each pair of the XD400/4v2’s channels
are designed to deliver power into speaker
loads equal to or greater than 2 ohms when
using a “stereo” configuration and speaker
loads equal to or greater than 4 ohms
when using a “bridged” configuration.
Speaker loads below 2 ohms nominal per
channel (or 4 ohms bridged) are not
recommended and may cause the amplifier
to initiate a protection mode which reduces
power output.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from a
single channel. The XD400/4v2 has been designed
for bridging of its main channel pairs without the
need for input inversion adaptors.
To bridge a pair of main channels, use the
“Left +” and “Right –”speaker connectors only
(the “Left –” and “Right +” remain unused). Each
bridged channel pair will deliver optimum power
into a 4 ohm load.
When a pair of the XD400/4v2’s channels are
bridged, they will deliver 200W x 1 into a 4 ohm
load or 150W x 1 into an 8 ohm load. Operating
a pair of bridged channels into a load lower than
4 ohms is not recommended.
A bridged pair of channels requires that
both channels in the pair receive input. You
must connect the mono or stereo source signal
to both the left and right inputs of the bridged
channel pair. Connection of only one input
will result in reduced power output, increased
distortion and can cause the amplifier to
overheat. Do not do this!
When a pair of the XD400/4v2’s channels are
operating in bridged mode, the output will be in
mono (only one channel). This mono channel can
contain only right channel information, only left
channel information, or the sum of the signals
from right and left input channels. In order to
achieve one of these options, configure the inputs
to that pair of channels in one of these two ways:
1) Left Channel Only or Right Channel Only
Information: If you wish to send a left-only or
right-only signal to a pair of the XD400/4v2’s
channels you must use a “Y-Adaptor” to split
the single channel signal into both left and
right RCA inputs of the bridged channel
pair. This option is used when deploying a
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio XD400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio XD400 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info