700465
12
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
12 | JL Audio - RD1000/1 Owners Manual
APPENDIX A:
Input Sensitivity Level Setting
Follow the steps below to adjust the input
sensitivity of each amplifier channel pair, simply
and easily, in just a few minutes to achieve overall
system balance.
Necessary Equipment
CD with a sine-wave test tone recorded at
0 dBfs reference level in the frequency range
to be amplified for that set of channels
(50 Hz for subwoofer channels, 1 kHz for a
midrange application). Do not use attenuated
test tones (-10 dB, -20 dB, etc.).
If your OEM source unit is not equipped with
a CD player, you may transfer the test tone to
a portable media player or thumb drive and
connect to your source units auxiliary input.
Make sure to disable any EQ/DSP modes on
your portable media player during level setting.
The Seven-Step Procedure
1) Disconnect the speaker(s) from the
amplifier’s speaker output connectors.
2) Turn off all processing (bass/treble, loudness,
EQ, etc.) on the source unit, processors (if
used) and amplifier. Set the fader control to
center position and the subwoofer level control
to 3/4 of maximum (if used to feed
the RD1000/1).
3) Set the “Input Voltage” switch to Low”. Turn
both Input Sensitivity control all
the way down.
4) Set the source unit volume to 3/4 of full
volume. This will allow for reasonable gain
overlap with moderate clipping at full volume.
5) Verify that you have disconnected the
speakers before proceeding. Play a track
with an appropriate sine wave (within the
frequency range to be amplified by the
RD1000/1) at 3/4 source unit volume.
6) Slowly increase the “Input Sensitivity
control until the “Clipping” LED is solidly lit,
indicating maximum, unclipped output. If the
Clipping” LED is solidly lit with the “Input
Sensitivity” control turned all the way down,
set the “Input Voltage” switch to the “High
position, then slowly increase the “Input
Sensitivity” control until the “Clipping” LED
is solidly lit.
7) Once you have adjusted each channel section
on the RD1000/1 to its maximum, unclipped
output level, reduce the source unit’s volume
to prevent sudden output bursts and reconnect
the speaker(s). Play music and adjust the “Input
Sensitivity” controls downward if the amplifier
requires attenuation to achieve the desired
system balance.
Do not increase any “Input Sensitivity” setting
for any amplifier channel or channel pair in the
system beyond the maximum level established
during this procedure. Doing so will result in
audible distortion and possible speaker damage.
It will be necessary to re-adjust the “Input
Sensitivity if any equalizer boost is activated
after setting the “Input Sensitivity with this
procedure. This applies to any EQ boost circuit,
including source unit tone controls or EQ circuits.
EQ cuts will not require re-adjustment.
+12 VDC Ground Remote
Turn On Mode
Rem.
|
Oset
|
Signal
Low
|
High
Clipping
Input Voltage
0
+12
+5
+10
+8
Bass Boost (dB) LP Filter Freq. (Hz)
Input Sensitivity
Monoblock Subwoofer Amplifier
MONO SUBWOOFER OUPUT
(
L
)
(
R
)
CH. 1
(
L
)
CH. 2
(
R
)
INPUT SECTION
PRE-OUTS
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio RD1000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio RD1000 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info