701313
4
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
6 JL Audi
7
“INPUT SENSITIVITY” GAIN ADJUSTMENT
Located next to the input connectors is a rotary
control labeled Input Sens.. This rotary control
can be used to match the source unit’s output
voltage to the input stage of the amplifier for
maximum clean output.
Reversed
|
Normal
Output Polarity
LP Filter Frequency (Hz)Input Sens. Bass Boost
min max
40 130 O +12dB
Power
Remote
Level
Port
LEFT
RIGHT
LEFT
RIGHT
Preamp
Outputs
Amplifier
Inputs
Rotating the control clockwise will result
in higher sensitivity (louder for a given input
voltage). Rotating the control counter-clockwise
will result in lower sensitivity (quieter for a given
input voltage). To properly set the amplifier for
maximum clean output, please refer to Appendix
A (page 12) in this manual. After using this
procedure, you can then adjust the level of the
amplifier by adjusting the input sensitivity
downward, if the amplifier requires attenuation to
achieve the desired system balance.
Do not increase the Input Sens. setting for
any amplifier in the system beyond the maximum
level established during the procedure outlined
in Appendix A (page 12). Doing so will result in
audible distortion and possible speaker damage.
“LP FILTER” CROSSOVER CONTROL
The J2-500.1 employs a 12dB/octave low-pass
(LP) active filter for its internal channel. This
feature is designed to attenuate frequencies above
its filter frequency, so that the systems subwoofers
do not reproduce any audible midrange content.
The low-pass filter in the J2-500.1 is fully
variable between 40 Hz and 130 Hz via the “LP
Filter Frequency control knob. The 12 oclock
position corresponds to 80 Hz, and is a good
starting point for system tuning.
Reversed
|
Normal
Output Polarity
LP Filter Frequency (Hz)Input Sens. Bass Boost
min max
40 130 O +12dB
Power
Remote
Level
Port
LEFT
RIGHT
LEFT
RIGHT
Preamp
Outputs
Amplifier
Inputs
“OUTPUT POLARITY” CONTROL
The J2-500.1 includes a switch to quickly reverse
the polarity of its audio output. This is very useful
for establishing a smooth transition between the
subwoofers and main speaker systems. Choose
the position that results in the strongest midbass
and the best “up-front” bass presence.
Reversed
|
Normal
Output Polarity
LP Filter Frequency (Hz)Input Sens. Bass Boost
min max
40 130 O +12dB
Power
Remote
Level
Port
LEFT
RIGHT
LEFT
RIGHT
Preamp
Outputs
Amplifier
Inputs
“REMOTE” TURNON
The J2-500.1 is turned on and off
using a conventional +12V remote turn-
on lead, typically controlled by the
source unit’s remote turn-on output.
The amplifier will turn on when +12V is
present at its Remote input and turn off when
+12V is switched off. If a source unit does not
have a dedicated remote turn-on output, the
amplifier’s turn-on lead can be connected to +12V
via a switch that derives power from an ignition-
switched circuit.
18 AWG wire is more than adequate for the
remote turn-on connection. To connect the
remote turn-on wire to the amplifier, strip 1/2-
inch (12 mm) of insulation from the wire and
insert it into the “Remote” receptacle on the
power connector. Tighten the connector down
using a Phillips screwdriver.
AMPLIFIER INPUTS”
The J2-500.1 only offers low-level (preamp
level) input connections via a single pair of RCA-
type jacks that are compatible with a wide range
of aftermarket source units and processors. If you
wish to use speaker level signals, you will need to
employ a line-output converter (not included).
Reversed
|
Normal
Output Polarity
LP Filter Frequency (Hz)Input Sens. Bass Boost
min max
40 130 O +12dB
Power
Remote
Level
Port
LEFT
RIGHT
LEFT
RIGHT
Preamp
Outputs
Amplifier
Inputs
You may run a stereo or a mono signal into
the inputs of the amplifier. The amplifiers input
section automatically sums stereo signals to mono
for the internal amplifier section.
The amplifier will operate with only one
input connection (left or right), but will require
an increase in input sensitivity to overcome the
loss of signal. If a mono input signal is to be run
into the RCA jacks, we recommend that you use
a “Y-adaptor to split the mono signal into both
the Left and Right inputs of the amplifier.
If you plan to use the preamp outputs to feed a
stereo amplifier, you must connect a stereo
signal to the input of the amplifier. A mono
signal into the amplifier will result in a mono
signal out of the preamp output.
J2_500_1_MAN_CH.indd 6-7 4/22/09 11:24:43 AM
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio J2 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio J2 500 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info