700447
4
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
6 | JL Audio - 600/1v3 Owners Manual
7
(for example, if there is an active low-pass
crossover in line before the amplifier), this
circuit will not operate properly.
To activate the signal sensing turn-on feature,
place the “Signal Sensing” switch in the “On
position. This should only be done if there is
no conventional turn-on lead connected to the
amplifier’sRemoteconnector. When in the
On” position, the signal sensing circuit will
monitor the audio input signal and turn the
amplifier on when signal is present. After about
25 seconds of no signal, the amplifier will shut off.
Turning on other amplifiers in signal sensing
mode: When the signal sensing circuit is turned
on, the Remote” Connector on the amplifier
may be used as a remote turn-on source for other
amplifiers in the system. +12V will be present
at the connector when the amplifier turns on in
signal sensing mode and will not be present when
the amplifier turns off.
IMPORTANT
!
You cannot use the turn-on output to turn on
processors that are in the signal path before the
600/1v3. (Signal will not pass through most
processors when they are not powered up,
meaning that the amplifier will not turn on
until that processor is active).
AMPLIFIER INPUT SECTION
The 600/1v3 employs a differential-balanced
input topology that provides the user with a high
degree of input flexibility while retaining superior
noise rejection. This type of circuit also allows
the 600/1v3 to accept high-voltage inputs from
factory source unit outputs without excessive
distortion or noise problems.
+12VDC Ground Remote Preamp Output Section
Infrasonic Filter
“Q” Center Freq. Boost (dB)
Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section
Subwoofer Output
MONO OUTPUT ONLY
Left Output Right Output
Left Ch. Right Ch.
Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range
|
Amp Filter
|
Out Filter
Output Mode Filter Slope Mode
Mode
|
Slope
Input Voltage Input Sens. Signal Sensing
12dB
|
24dB
Filter Mode
LP
|
HP
Bass EQ
Off
|
On
Off
|
12dB
|
24dB Low
|
High Off
|
On
Off
|
On
40
45
55
65
80
100
200 15
18
22
30
45
55
60 40
45
55
65
80
100
200
0.5
0.7
1.1
1.6
2.7
4.3
20
25
30
40
60
75
80 0
+4
+10
+13
+15
Monoblock Subwoofer Amplifier
1) Input Connections: A standard left/right pair
of RCA type jacks is used for input on
the 600/1v3. You may run a stereo or a mono
signal into the inputs of the amplifier. The
amplifier’s input section automatically sums
stereo signals to mono for the internal
amplifier section and for the “LP” “Filter
Mode” of the Preamp Output” section.
IMPORTANT
!
If you plan to use the “Preamp Output” in
“Full-Range” or “HP” mode to feed a stereo
amplifier, you must connect a stereo signal to
the input of the amplifier. A mono signal into
the amplifier will result in a mono signal out of
the preamp output. (Its a great amplifier, but it
doesn’t do magic).
The amplifier will operate with only one input
connection (left or right), but will require an
increase in input sensitivity to overcome the loss
of signal. If a mono input signal is to be run, we
recommend that you use a “Y-adaptor” like the
JLAudio ECS model XD-CLRAICY-1F2M to split
the mono signal into both inputs of the amplifier.
2) Input Voltage Range: A wide range of
signal input voltages can be accommodated
by the 600/1v3’s input section (200mV – 8V).
This wide range is split up into two sub-
Ground Connection
The chassis ground connection must be made
using 4 AWG pure copper wire and should be
kept as short as possible, while accessing a solid
piece of sheet metal in the vehicle. The surface of
the sheet metal should be sanded at the contact
point to create a clean, metal-to-metal connection
between the chassis and the termination of
the ground wire with a brass or copper power
ring. For optimal grounding, we recommend
the use of a JLAudio ECS master ground
lug (XB-MGLU). Alternatively, a sheet metal
screw or bolt can be used with a star washer.
IMPORTANT
!
Many vehicles employ small (10 AWG - 6
AWG) wire to ground the battery to the vehicle
chassis and to connect the alternator’s positive
connection to the battery. To prevent voltage
drops, these wires should be upgraded to 4
AWG pure copper wire when installing amplifier
systems with main fuse ratings above 60A.
TURNON OPTIONS
The 600/1v3 can be turned on and off using
two different methods:
1) A conventional +12V remote turn-on lead.
2) A signal sensing turn-on circuit.
+12VDC Ground Remote
Preamp Output Section
Infrasonic Filter
“Q” Center Freq. Boost (dB)
Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section
Subwoofer Output
MONO OUTPUT ONLY
Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range
|
Amp Filter
|
Out Filter
Output Mode Filter Slope Mode
Mode
|
Slope
Input Voltage Input Sens. Signal Sensing
12dB
|
24dB
Filter Mode
LP
|
HP
Bass EQ
Off
|
On
Off
|
12dB
|
24dB Low
|
High Off
|
OnOff
|
On
40
45
55
65
80
100
200 15
18
22
30
45
55
60 40
45
55
65
80
100
200
0.5
0.7
1.1
1.6
2.7
4.3
20
25
30
40
60
75
80 0
+4
+10
+13
+15
Monoblock Subwoofer Amplifier
To select between the two modes there is a
switch, marked Signal Sensing”, located in the
Amplifier Input Section” of the front panel.
1) Conventional Remote Turn-On Method:
uses a conventional +12V remote turn-on
lead, typically controlled by the source unit’s
remote turn-on output. The amplifier will
turn on when +12V is present at its “Remote
input and turn off when +12V is switched
off. If a source unit does not have a dedicated
remote turn-on output, the amplifiers turn-on
lead can be connected to +12V via a switch
that derives power from an ignition-switched
circuit. To use this method, selectOff” on
the “Signal Sensing” switch in the “Amplifier
Input Section. The 600/1v3’s “Remote
turn-on connector is designed to accept 12
AWG – 8 AWG wire. 12 AWG is more than
adequate for this purpose. To connect the
remote turn-on wire to the amplifier, first back
out the set screw on the top of the amplifier,
using the supplied hex wrench. Strip 1/2
inch (12mm) of wire and insert the bare wire
into the receptacle on the front panel of the
amplifier, seating it firmly so that no bare wire
is exposed. Smaller wire than 12 AWG can be
used, but it may be necessary to strip 1 inch
of insulation from the wire and fold the bare
wire in half prior to insertion. While holding
the wire in the terminal, tighten the set screw
firmly, taking care not to strip the head of the
screw and making sure that the wire is firmly
gripped by the set screw.
2) Signal Sensing Turn-On Method: A valuable
feature of the 600/1v3 is its ability to be turned
on and off by the presence or lack of signal at
its audio inputs. This allows you to operate the
amplifier without having to locate a remote
turn-on lead at the source unit. This can be
very useful if interfacing the amplifier with
some OEM source units that do not have
conventional turn-on leads.
IMPORTANT
!
The sensitivity of the signal sensing turn-on
circuit has been designed for high-level
(speaker level) signals, not for low-level
(preamp level) signals. Using this feature with
low-level (preamp level) signals is not
recommended. We do not recommend this
method of turning the amplifier on and off as a
default. Whenever possible, use the
conventional remote turn-on lead method. The
signal sensing circuit is designed to detect
midrange frequency signal presence. If the
signal feeding the amplifier is not full-range
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio 600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio 600 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info