422470
20
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
Jumper Connections
The K2 S9800 is shipped with Tw i s t e d
Pair Wire Jumpers installed between its
low frequency and high frequency ter-
minals. Please s e e Fi g u r e 9. To prepare
the K2 S9800 for bi-wire or bi-amp
operation, these jumpers must be
removed by completely unscrewing
each binding post, removing the
jumpers, and replacing the binding
posts. Wires can then be connected to
each set of terminals (s e e Fi g u r e 10) .
A m p l i fier Connections
I m p o r t a n t : Turn all amplifiers off
before connecting or disconnecting
P roject K2 S9800 l o u d s p e a k e r s .
Making connections while an amplifier
is operating could seriously damage
the loudspeaker system and void the
w a r r a n t y. All amplifiers must also be
turned off before connecting or discon-
necting cables at the amplifier or pre-
amplifier inputs.
All connections between the amplifi-
er(s) and the P roject K2 S9800 1oud-
speaker system are made at the termi-
nals located on the back of the enclo-
sure (Fi g u re 9 and 10). The left-hand
terminals (black stripe) are negative,
and the right-hand terminals (red
stripe) are positive. These correspond
to the negative and positive conductors
in the speaker wire. Each speaker wire
contains two conductors, one of which
will have a stripe, color markings, or a
r i d g e .
Assign one of the two conductors as
the negative conductor and the other as
the positive conductor. Use these same
designations for all system wiring.
Always connect the conductors of the
speaker wire appropriately to the corre-
sponding negative and positive termi-
nals on all system components. T h i s
will ensure that all components will
work together ("in phase"). Connecting
the speakers out of phase will not dam-
age them but will result in reduced low
frequency output and impaired stereo
e ff e c t .
Speaker wires may be fastened to the
terminals by several methods. T h e
most positive connection is made by
directly connecting clean, bare connec-
tors (exposed by stripping the ends of
the wire) to the terminal posts.
For this type of connection, loosen the
knobs on the terminals and insert the
exposed (bare) ends of each speaker
wire into the hole exposed on the ter-
minal shaft ( + to +, – to – ) (s e e
Fi g u re 11). Retighten the knob on each
terminal so that a snug positive con-
nection is achieved. Do not apply
excessive force and do not overtighten.
To avoid a short circuit, trim off any
excess wire that is not in contact with
the binding post contact surfaces.
20
Project K2 S9800
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JBL k2 s9800 s e mahogany hoogglans bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JBL k2 s9800 s e mahogany hoogglans in de taal/talen: Engels als bijlage per email.

De handleiding is 0,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info