509865

Inverto IDLV-5100P Handleiding

34
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
IDLV-5100P
Professional Multi-format HDTV Integrated Receiver Decoder
En
Professional Multi-format
HDTV Integrated Receiver
Decoder
User Manual
IDLV-5100P
En
1
Table of Contents
Notices 2
Before using the device 3
Overview 4
Control with display and keypad 6
Menu structure and operations 8
Remote management and control over web interface 18
Technical Specications 30
Default Device Parameters On Delivery 33
Safety 37
Warrenty, service and support 38
2
Notices
COPYRIGHT (Copyright © 2010 Inverto Digital Labs )
Not to be copied, used or translated in part or whole without Inverto prior consent in writing except approval of
ownership of copyright and copyright law.
WARRANTY
This warranty does not cover parts which may become defective due to misuse of the information contained in
this manual.
Read this manual carefully and make sure you understand the instructions provided. For your safety, be aware of
the following precautions.
WARNING! IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
To• reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
To avoid explosion danger, do not dispose of batteries in an open re.•
CE MARK FOR EUROPEAN HARMONISED STANDARDS
The CE mark which is attached to these products means it conforms to EMC Directive (89/336/EEC) and
Low Voltage Directive (73/23/EEC).
IMPORTANT INFORMATION
Please retain the original packaging, should it be necessary at some stage to return the unit.
Disposal of Old Electrical and Electronic Equipment (Applicable in the European Union and other European
countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by inappropriate waste handling of this
product. The recycling of materials will help to conserve natural resources. For more detailed information about
recycling of this product, please contact your local Civic Ofce, your household waste disposal service, or the shop
where you purchased the product.
COPYRIGHTS
Television programmes, movies, video tapes, discs, and other materials may be copyrighted. Unauthorized
recording of copyrighted material may be against the copyright laws in your region. Also, use of this product with
cable television transmissions may require authorization from the cable television operator or transmitter/owner.
VENTILATION
Do not expose the product to high temperatures, such as placing it on top of other product that produce heat or •
in places exposed to direct sunlight or spot lights.
The ventilation slots on top of the product must be left uncovered to allow proper airow into the unit. •
Do not stand the product on soft furnishings or carpets. •
Do not stack electronic equipments on top of the product.•
Do not place the product in a location subject to extreme changes in temperature. The temperature gradient •
should be less than 10 degrees C/hour.
Place the product in a location with adequate ventilation to prevent the build-up of heat inside the product. The •
minimum ventilation space around the unit should be 7 cm. The ventilation should not be impeded by covering
the ventilation openings with items, such as newspapers, table cloth, curtains, etc.
POWER SOURCES
The product is not disconnected from the AC power source (mains) as long as it is connected to the power outlet •
or wall socket, even if the product is turned off.
If the product will not be used for a long period of time, disconnect it from the AC power outlet or wall socket.•
En
3
Before Using the device
Thank you for purchasing the IDLV-5100P Professional Multi-format HDTV Integrated Receiver Decoder. This
User Manual is written for operators/users of the IDLV-5100P to assist in installation and operation. Please read
this user manual carefully before installation and use of the devic.
FOR YOUR SAFETY
This equipment is provided with a protective earthing ground incorporated in the power cord. The main plug shall
only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective
conductor, inside or outside the device, is likely to make the device dangerous. Do not remove the covers of this
equipment. Hazardous voltages are present within this equipment and may be exposed if the covers are removed.
Only Inverto trained and approved service engineers are permitted to service this equipment.
The supplied AC power cable must be used to power the device. If the power cord becomes damaged it must be
replaced. No operator serviceable parts inside. Refer servicing to Inverto trained and approved service engineers.
For the correct and safe use of the device, it is essential that both operating and servicing personnel follow
generally accepted safety procedures in addition to the safety precautions specied in this manual. Whenever it
is likely that safety protection is impaired, the device must be made in-operative and secured against unintended
operation. The appropriate servicing authority must be informed. For example, safety is likely to be impaired if the
device fails to perform the intended measurements or shows visible damage.
WARNINGS
The mounting environment should be relatively dust free, free of excessive vibration and the ambient •
temperature between 0C° to 40C°. Relative humidity of 20% to 80% (non-condensed) is recommended.
Avoid direct contact with water.•
Never place the equipment in direct sunlight.•
The outside of the equipment may be cleaned using a lightly dampened cloth. Do not use any cleaning liquids •
containing alcohol, methylated spirit or ammonia etc.
For continued protection against re hazard, replace line fused only with same type.•
Air intake for cooling is achieved via holes at the side of the device and the fans inside. The air ow should not •
be obstructed. Therefore, the device has to be placed on a at surface, leaving some space at the sides of the
device.
When in operation, the internal temperature should not exceed the limit of 70C°.•
4
Overview
The IDLV-5100P IRD provides operators an ideal solution for receiving, remultiplexing, descrambling and decoding
missions. The IDLV-5100P is equipped with a variety of inputs that ensures compatibility with all transmission
media.
The IDLV-5100P’s remultiplexing capabilities enable creation of new transport streams that are subsets of the
original stream. Customized services may be output as multiple SPTS or MPTS over IP, as well as over ASI.
Using the dual DVB common interfaces, IDLV- 5100P could decrypt multiple services in one transport stream or
two. IDLV- 5100P features a broadcast quality decoder for MPEG-2 and MPEG-4 AVC/H.264 in both Standard
Denition and High Denition formats, and provides a variety of industry standard digital and analog outputs,
including CVBS video, AES/EBU Audio, analog Audio, SD-SDI and HD-SDI. The unit also performs HD down-
conversion and aspect ratio adaptation of HD programs to generate professional quality baseband analog video
and audio outputs for easy integration with existing cable network infrastructure. This all-in-one architecture makes
the IDLV-5100P an ideal solution for video distribution and contribution networks.
CHARACTERISTICS
M• ultiple inputs DVB-T2/S2/S/C/T/T2, TS/IP, ASI and DS3/E3 (optional)
Supports DVB-S2 Input Stream Identier (ISI, optional) and DVB-T SFN MIP pass through •
Redundant backup among Tuner, ASI and TS/IP with congurable priority •
SD/HD MPEG-2 and MPEG-4 AVC/H.264 digital video decoding •
Two Audio PIDs decode or pass through (compressed) in SDI output •
Multiple Analog and Digital Outputs, ASI, CVBS, YPbPr, HDMI, SD/HD-SDI, AES/EBU Audio, TS/IP •
Built-in TS re-multiplexer receives 2xASI, Tuner and TS/IP Inputs •
2x DVB-CI Slots, multi-program decryption, BISS-1 and BISS-E decryption •
Dynamic PMT detection and automatic updating •
Supports VBI TELETEXT, EBU/DVB Subtitle, Closed Caption •
UDP/RTP, Unicast/Multicast, and SPTS/MPTS over IP (full duplex, optional) •
Remote management by SNMP, HTTP WEB and PC HDMS software •
PCM audio embedded in SDI and HDMI outputs •
PCM audio output on two AES/EBU audio output ports •
On Site software update through IP •
RSSI, received Eb/No & BER monitoring•
The following table summarizes the main functionalities and availability for the different series:
Model IDLV 5100P
Interface
-10x -20x -30x -43x -44x -46x
Tuner T, T2, S/S2 or DS3/E3
ASI Input x2 x2 x2 x2 x2 x2
Common Interface x2 x2 x2 x2 x2 x2
Built-in Re-mux
ASI-Output x2 x2 x2 x2 x2 x2
HDMI x1 x1 x1 x1 x1 x1
SDI x1 x1 x1 x1
YPbPr x1 x1 x1 x1 x1 x1
Audio L/R x2 x2 x2 x2 x2 x2
AES-EBU x2 x2 x2 x2 x2 x2
CVBS x2 x2 x2 x2 x2 x2
10/100M extension board
(Dual 6 Ch)
10/100M extension board
(32 Ch)
GbE extension board
(Full duplex)
● standard
x = T, T2, S/S2 or DS3/E3
En
5
BLOCK DIAGRAM
The diagram below shows a top level architecture and functional block diagram of the IDLV-5100P IRD Platform:
IDLV-5100P Functional Block Diagram
6
Control with display and keypad
IDLV-5100P series can be controlled by the keypad on front panel.
FRONT PANEL
IDL V -5100P Professional Multi-format SD/HD Integrated Receiver Decoder
Enter Exit
Po we rTuner Lock Alarm
OPERATION BUTTONS
LCD
COMMON INTERFACE
Tuner LoCk
ALArm
power
POWER Power indicator, green light means power is OK
TUNER LOCK Tuner lock indicator, green light means signal is locked; no light means no
signal input or wrong parameters setting.
ALARM Alarm indicator.
LCD 2 × 20 character LCD.
Operation buttons [◄] [▲] [▼] [►].[ENTER] [EXIT] buttons
[▲][▼] are used to up/down pages of menu or increase/decrease value when
edit numbers.
[◄] [►] are used to move cursor
[ENTER] is used to enter sub menu or conrm operation
[EXIT] is used to return to the previous menu or cancel operation.
Common Interface PCMCIA Module slots
En
7
REAR PANEL
B4 B5 B6 B9B8B7 B10B2 B3 B11
B12 B14 B20B19B18B17B16B15 B21
B1
B13 B22
B1 TS/IP TSoIP interface (not available on IDLV-5100P -10x and -30x
models)
B2 RS-232 serial port for printing informationB3
B3 ASI OUT2 Group2 ASI output port (one for back-up)
B4 ASI OUT1 Group1 ASI output port (one for back-up)
B5 ASI1 IN ASI1 input port
B6 YPbPr YPbPr output port
B7 L-Audio-R1 Group1 RCA audio output port
B8 Audio1 AES/EBU and Balance Audio output port1 (need to use the RS232-
to-XRL converting cable in accessories)
B9 TUNER OUT Tuner signal loop through output port
B10 TUNER IN Tuner signal input
B11 SWITCH Power switch
B12 MANAGEMENT LAN port for software update
B13 ASI2 IN ASI2 input port
B14 SDI2 SDI2 output port
B15 SDI1 SDI1 output port
B16 HDMI HDMI output port
B17 CVBS CVBS BNC output port
B18 CVBS CVBS RCA output port
B19 L-Audio-R2 Group2 RCA audio output port
B20 AUDIO2 AES/EBU and Balance Audio output port2 (need to use the RS232-
to-XRL converting cable in accessories)
B21 GND Grounding terminal
B22 POWER SOCKET AC 90~250V 50-60Hz input
8
Menu structure and operations
Turn on the device and wait for 8 to 10 seconds. During this period, the device will complete self inspection and
conguration. The name of the device will be displayed on the top row of the LCD, and the local IP address will
be displayed on the bottom row of the LCD:
Digital TV Processor (factory default unit-name)
IP: 10.10.70.48 (factory default IP Address for LAN access)
If no message is presented or there is no light on the display, the device is defective and has to be returned for
servicing.
Note: The local IP address and unit name can be changed in the System Menu (refer to sections Optional
Function/External Board Type and Unit Name under System respectively). Use the <ENTER>-key to enter on the
Main Menu. The UP and DOWN keys are used to choose between the three main menus.
OUTPUTS SYSTEMINPUTS
TS OVER IP
FOR IDLV 5100P-46X
MODELS ONLY
MAIN MENU
INPUTS
Under Inputs Menu, you can monitor and congure the parameters of the ASI, Tuner, and TS over IP inputs:
S TAT US
IP (ETHERNET
(OPTION)
DVB-S/S2
COFDM/
D V B -T 2 /
QAM/
RSSI
INPUTS
En
9
Main menu Sub-menu Description
Inputs
Status Displays the status of the input signals for ASI1, ASI2, TUNER and IP IN
DVB-S2 This menu is only displayed on IDLV-5100P-xxS2 models
LNB Frequency: Input LNB frequency
Satellite Frequency: Input downstream frequency of satellite
Symbol Rate: Input symbol rate of satellite
LNB Voltage: Select the correct LNB voltage output of the F-connector: Off, 13
V, 18 V. <13V for Vertical/Left hand polarization, 18V for Horizontal/Right hand,
OFF for LNB Power off.>
LNB 22KHz: Activate the LNB 22 kHz control signal to the LNB: On or Off.
<22KHz control signal switches the LNB to receive high band if any>
DISQEC: Select OFF/Port A/Port B/Port C/Port D
PLS Gold Code: N/A
Frequency Offset High: Set the frequency offset for signal lock. the range is
1000~5000KHz
Frequency Offset Low: The range is -5000KHz~-1000KHz
COFDM This menu is only displayed on IDLV-5100P-xxT models
Frequency: Enter the frequency of the COFDM signal in MHz.
DVB-T2 This menu is only displayed on IDLV-5100P-xxT2 models
Frequency: Input terrestrial frequency.
Bandwidth: Select bandwidth - 6Mhz, 7Mhz or 8Mhz.
QAM This menu is only displayed on IDLV-5100P-xxC model
Constellation: Enter the modulation mode of the QAM signal.
Frequency: Enter the frequency of the QAM signal in MHz.
Symbol Rate: Edit the symbol rate to the proper value in KBaud.
RSSI Display the quality of the received DVB-S2 signal.
Ethernet This menu is only displayed on IDLV-5100P-20x and -44x models which set TS/
IP streaming board as “100M Single IN”
Stream IP Addr: Enter the IP address for streaming IP input of the unit.
Stream Netmask: Enter the network sub mask for the subnet to which the unit
is connected for IP streaming trafc.
Stream Gateway: Set the gateway for the network to which the unit is con-
nected for IP streaming trafc.
Stream Mac Address: Ffactory-set MAC addresses are guaranteed to be
unique. Therefore you cannot congure the address.
Multicast IP Addr: Enter the IP address of the multicast stream for the trans-
port stream over IP.
Multicase UDP Port: Enter the UDP port number of the TS over IP stream.
Protocol: Select the protocol for multicast: UDP or RTP.
Output Smoothing: Set the quality of TS that is received via the TS/IP input.
Auto: The bit rate is variable.
Disable: The unit let the TS pass by.
Fixed Rate: The bit rate is xed.
TS Bit Rate: Set the bit rate of the TS received via the TS/IP input. The setting
is only valid when the output smoothing is congured as Fixed Rate.
10
OUTPUTS
Under Outputs Menu, you can monitor and congure the parameters of BISS, CI, AV decoder, ASI1/2 outputs,
SDI out, Ethernet (IP), Mux/Filter and Backup.
(A) The Mux/Filter menu is showed only if the functional block is enabled. Refer to Mux Function paragraph
under Optional Function section in System.
(B) The menu is showed only if the IP streaming in/out board is installed and the TS/IP streaming board is set to
“IP Out”. Refer to External Board Type paragraph under Optional Function section in System.
ouTpuTs
Asi1
ip (eTherneT)
(opTion)
sDiAsi2CiBiss DeCoDer muX BACkup
Outputs
BISS
BISS Mode: Set BISS mode, Select Mode 0, Mode E or Mode 1. Different BISS
modes have different sub-menus under BISS Menu.
BISS Source: select the BISS source from ASI1, ASI2, Mux TS and Tuner.
Mode 1 Key Enter: Set Biss 1, password is required.
Mode E Key Enter: Set Biss E, ID number and password are required
Program Setup: Press the <ENTER>-key to enter ‘Program Setup’ sub-menu. It
shows all programs detected by the IDLV-5100P. If there is no TS input, the front
panel will read “0-TS Invalid”.
CI
CI Source: Select Tuner, ASI1 input , ASI2 input or TS/IP input (only for IDLV-
5100P-20x and -44x models which set TS/IP streaming board as “100M Single
IN”) to set the signal source of descrambling, press <ENTER>-key to save or
press <EXIT>-key to scrap.
Setup: Under this sub menu, you can see all program names from the source
of CI that was set in ‘CI Source’ previously. All free-to-air programs are marked
with ‘Free’ in the rst row.
In order to select which program will be de-encrypted, press the <↑> or <↓>-key
to roll up and down the program names and press <ENTER>-key to change the
status of the corresponding program (only encrypted program could be selected).
Three different options can be set:
Slot 1 (de-encrypted with upper CAM inserted)
Slot 2 (de-encrypted with lower CAM inserted)
Bypass (no de-encryption).
The status will be shown in the rst row on the LCD display. Conrm this setup
when leaving this sub menu, press <ENTER>-key to save or press <EXIT>-key
to scrap.
CAM name: Under this sub menu, you can see the names of CAM modules.
Decoder
Status: OK or Alarms indicates the status of the decoder.
Source: select the signal source of SDI, HDMI, YPbPr and CVBS outputs, there
are 5 type of signal source optional:
CI De-encrypted: the de-encrypted transport stream from CI functional block will
be delivered to the ASI output port on the back panel.
TUNER: the transport stream from Tuner block will be delivered to the ASI output
port on the back panel.
ASI1 Input: The transport stream comes from ASI1 input port will be delivered to
the ASI1 output port on the back panel.
ASI2 Input: the transport stream comes from ASI2 input port will be
delivered to the ASI2 output port on the back panel.
En
11
Decoder
Mux TS: The transport stream comes from internal Mux functional block will be
delivered to the ASI output port on the back panel.
Program: Under this sub menu, you will see all program names detected by
IDLV-5100P. The programs could be coming from ASI input, Tuner, TS/IP input,
the internal CI de-encryption block, BISS De-encryption block or MUX TS. Use
the <↑> or <↓>-key to roll up or down between the program names, and use
<←>-and <→>-key to switch among input sources, where a number in front of
the program name indicates the input source:
0-xxxxx displays the program name, which comes from ASI1 input; 1-xxxxx
from TUNER input; 2-xxxxx from TS/IP input; 3-xxxxx from the CI; 4-xxxxx from
ASI2 input; 5-xxxxx from BISS De-encrypted input; 6-xxxxx from MUX TS.
Video: You can congure the video parameters of programs in this submenu.
Press the <ENTER>-key to conrm or press the <EXIT>-key to cancel.
Video Standard: you can select Auto/1920x1080i 60/1920x1080i
50/1280x720p 60/1280x720p 50/720x480p 60/720x576p 50/525x480i
60/625x576i 50 for the composite video output.
Screen: Select the screen mode: Auto, 4:3 Full, 16:9 Full or 4:3 Letterbox.
DVB Subtitle Lang: Select the language of DVB Subtitle.
EBU Subtitle Lang: Select the language of EBU Subtitle.
Subtitle Priority: Congure the priority of Subtitle; choose whether DVB or
EBU should be rst.
Fail Mode: Choose which kind of picture will appear when signal is fail. You can
select Black Screen or No Sync or Still Picture.
Closed Caption: Enable or disable the Close Caption function. This switch
controls both CC on CVBS and SDI.
VBI Mode: Enable or disable the VBI. VBI option only controls Closed Caption
over CVBS. To activate the CC over CVBS, enable the VBI option.
CVBS Sub PAL: Select PAL mode, including PAL-B/D/G/H/I, PAL-N, PAL-N_C
and SECAM.
CVBS Sub NTSC: Select NTSC Mode, including NTSC-M, NTSC-M_J, NTSC-
M_443 and PAL-M.
Note: The sub-menus VBI Mode, CVBS Sub PAL and CVBS Sub NTSC will
only show up when the Closed Caption option is on.
Audio: You can congure the audio settings in the submenu
Audio1 Level: modify the audio1 level within this range: 0~99.•
Audio1 Mode: select Stereo, Left, Right or Mono for soundtracks.•
Audio1 Priority: select the priority of the audio.•
Audio2 Level: modify the audio2 level within this range: 0~99.•
Audio2 Mode: select Stereo, Left, Right or Mono for soundtracks.•
Audio2 Priority: select the priority of the audio.•
HDMI/AES Embeded: select from PCM or Compressed. Select Compressed to
enable HDMI Dolby pass-through. Otherwise select PCM.
Mode: select from Manual Selection and First Service. First Service means
to select the program no. automatically, normally the rst program in the TS.
Manual Selection means to select the program manually.
A/V Alarm Switch: There are two switches control the alarm separately:
Video Alarm: enable or disable the video alarm.•
Audio Alarm: enable or disable the audio alarm.•
ASI1
ASI1 Source: There are 5 optional types for the signal source:
C• I De-encrypted: The de-encrypted transport stream received from the CI
functional block will be delivered to the ASI output port on the back panel.
TUNER: The transport stream received from Tuner block will be delivered to •
the ASI output port on the back panel.
ASI1 Input: The transport stream received from the ASI1 input port will be •
delivered to the ASI1 output port on the back panel.
ASI2 Input: the transport stream received from the ASI2 input port will be•
12
delivered to the ASI2 output port on the back panel.
Mux TS: The transport stream received from the internal Mux functional block •
will be delivered to the ASI output port on the back panel.
(Mux TS is only valid when the Mux function block is enabled and turned on).
Press <ENTER>-key to save or press <EXIT>-key to scrap. A few seconds after
the source was selected, the TS will be delivered to the ASI output port on the
back panel.
ASI2 The same conguration method as detailed for ASI1 above.
SDI
This menu not available on models IDLV-5100P-10x and -20x.
Embedded Audios: There are 2 options: On and Off.
Closed Caption Mode: Select from SMPTE 708,SMPTE 608, Line 21, and
Auto. The mode of closed caption needs to be selected based on the video res-
olution. SMPTE 708 and SMPTE 608 are more suitable for HD video, SMPTE
608 and Line 21 are for SD. When select Auto, the unit will choose SMPTE 608
for HD video, and Line 21 for SD video.
Note: Before doing the setup, be sure to enable the Closed Caption switch in
the menu Decoder->Video->Closed Caption.
AC-3 Pass Thru CH: Select the channel for AC-3 audio pass through.
You can select Channel 3-4 or Channel 5-6
E t h e r n e t
(IP)
This menu is displayed only on IDLV-5100P-20x and -44x models which set TS/
IP streaming board as “100M Single IN” and IDLV-5100P-43x which set TS/IP
streaming board as “100M Dual Out”.
The parameters listed below must be set to appropriate values for the network
over which the transport stream over IP is broadcasted.
Stream IP Addr: Enter the IP address for streaming IP output of the unit.
Stream Netmask: Enter the network sub mask for the subnet to which the unit
is connected for IP streaming trafc.
Stream Gateway: Set the gateway for the network to which the unit is con-
nected for IP streaming trafc.
Stream Mac Address: Factory-set MAC addresses are guaranteed to unique.
Therefore you cannot congure the address.
Gateway Mac Address: Gateway MAC addresses need to be set if your
unicast target is in another network segment. If the unicast target is in the
same network segment of 5100P, the gateway MAC address should be set to
FF:FF:FF: FF:FF:FF.
If the unit is IDLV-5100P-43x which is set as “100M Dual Out” in the system
menu, two menus will appear and each contains above ve setups so you can
set the two IP output separately
TS/IP1: This sub-menu contains ve items: Stream IP Addr, Stream Netmask,
Stream Gateway, Stream Mac Address and Gateway Mac Address. The setup
method is the same as above.
TS/IP2: The same as TS/IP1.
Protocol: Select the protocol for multicast: UDP or RTP.
TS Pkts Per UDP: Set the number of the TS packages encapsulated in one
UDP package. The valid range goes from 1 to 7.
Time To Live: Set the number of the routers over which the TS over IP can be
transmitted. The valid range goes from 1 to 255.
Type of Service: Select the type of service. There are: Normal, Min Monetary
Cost, Max Reliability, Max Throughput or Min Delay optional.
Source: Select the source of the transport stream over IP streaming output.
There are 5 type of source optional: ASI1 Input, ASI2 Input, CI De-encrypted,
TUNER, and Mux TS
Mode: Select the mode of IP stream; you can select DVB or IPTV.
En
13
E t h e r n e t
(IP)
DVB mode: The transport stream received from the ‘source’ selected in previ-
ous step will be packed into IP Stream directly. Therefore the IP stream carries
all programs and is delivered to the specied Multicast or Unicast IP address.
IPTV mode: The transport stream received from the ‘source’ selected in previ-
ous step will be de-Muxed to several single programs, and each program is
packed into one IP stream. Therefore each IP stream carries only one program
and is delivered to the specied Multicast or Unicast IP address. You can con-
gure maximum 32 IPTV channels.
Multicast Setup: Use <ENTER>-key to enter sub-menu. The sub-menu is dif-
ferent according to different ‘mode’ selected in previous step.
DVB mode
Multicast IP: Enter the IP address of the IP stream for the transport stream
over IP output. You can congure the IP stream output mode in Multicast or Uni-
cast. Multicast could be established by setting Multicast IP address in the range
of 224.0.0.0 to 239.255.255.255.
Unicast could be established with the same settings of Multicast, the only
differences are the Multicast IP address, and should NOT be in the range of
224.0.0.0 to 239.255.255.255, which is for Multicast. Although the display is
‘Multicast IP’ on the rst row, the stream itself is Unicast. The IP address of
receiver device (maybe PC with VLC) needed to be set to as the unicast ad-
dress on IDLV-5100P, please don’t use DHCP to get a dynamic IP address for
receiver device.
Multicast UDP Port: Enter the UDP port number of the TS over IP stream
output.
Target MAC address: Set the MAC address of your target device
IPTV mode
Max Channels (<=32): You can congure the number of IPTV channel. The
valid range goes from 1 to 32. Each channel could be congured independently.
Channel x: ‘x’ means the channel number. Press <ENTER>-key to go down to
the sub-menu. There are 6 sub-menus:
x-Multicast IP: Enter the IP address of the IP stream for the transport stream •
over IP output.
You can also congure the IP stream output mode in Multicast or Unicast by
setting Multicast IP address.
x-Multicast Port: Enter the UDP port number of the TS over IP stream output.•
x-Switch: each channel could be switched On/Off independently. The default •
value is ‘off’. To activate the channel, you should turn on.
x-Program: it shows all programs carried by the transport stream from the •
source selected. Press <ENTER>-key and use <↑> <↓>-keys to roll up and
down between the program names, where a number in front of the program
name indicates the input source:
0-xxxxx displays the program name, which comes from ASI input; 1-xxxxx
from TUNER input; 2-xxxxx from TS/IP input; 3-xxxxx from the CI; 4-xxxxx
from ASI2 input; 5-xxxxx from BISS De-encrypted input; 6-xxxxx from MUX
TS.
EIT Pass Through: Disable or enable the EIT Pass through function.•
TDT/TOT Pass Through: Disable or enable the TDT/TOT Pass through •
function.
All encrypted programs are labeled with a ‘$’ sign on the rst row. Press
<ENTER>-key to the program just be selected to be delivered to the specied
IPTV channel or to scrap by pressing <EXIT>-key.
14
Mux
This menu is shown only when the Mux function block is enabled and turned
on.
Mux Switch: The internal multiplexer could be switched On/Off. The default
value is ‘off’. To activate the re-Multiplexing function, you should turn on this
Mux functional block.
Bit Rate: Should be set to a specied value that doesn’t exceed the Maximum
physical limit of the output medium. For example, to deliver the multiplexed TS
to an 8MHz DVB 256QAM modulator, it should not exceed 55000Kb/s, other-
wise overow occurs. Output Bit Rate: set the total bit rate of the multiplexed
stream.
TS ID: You can congure the TS ID to mark the multiplexed TS. Default value
is 1.
Program List: Press the <ENTER>-key to enter ‘Mux List’ sub-menu. It shows
all programs detected by IDLV-5100P. The programs could be come from ASI
input, Tuner, TS/IP input or the internal CI de-encryption block. Use the <↑>
or <↓>-key to roll up or down between the program names, and use <←>-and
<→>-key to switch among input sources, where a number in front of the pro-
gram name indicates the input source:
0-xxxxx displays the program name, which comes from ASI input; 1-xxxxx from
TUNER input; 2-xxxxx from TS/IP input; 3-xxxxx from the CI; 4-xxxxx comes
from ASI2 input; 5-xxxxx from BISS De-encrypted input.
On ‘Program List’ sub-menu, on the rst row, all encrypted programs are
labeled with a ‘$’ sign. All programs that are being selected to be re-multiplexed
are labeled as ‘Pass’, otherwise, the un-selected programs are labeled as ‘Fo-
brid’. Use <ENTER>-key to selected or un-selected the program being shown.
When leaving the ‘Program List’ sub-menu, a new menu will be shown ‘Conrm
changed?’ Press <ENTER>-key to validate all programs just be selected to be
multiplexed or to scrap by pressing <EXIT>-key.
After a few seconds, the multiplexed TS will be generated and delivered to the
specied destination(s).
Backup
This menu is showed only when the Backup function block is enabled and
turned on.
Main channel: Select main channel from ASI1, ASI2 or Tuner.
Backup channel: Select backup channel from ASI1, ASI2 or Tuner.
Main CH Unlock Time: Set Main CH Unlock Time, ranging from 0 to 59 sec-
onds. When signal of the main channel remains the disconnected status over
this value, the unit will switch to the backup channel automatically.
Main CH Recover Time: set Main CH Recover Time, ranging from 0 to 59 sec-
onds. When the signal of the main channel recovers and remains stable over
this value, the unit will switch back to the main channel.
SYSTEM
The system menu provides information about the general functions, the surroundings equipment and the
hardware being used.
sYsTem
properTies mAChine TYpe
o p T i o n A L
FunCTion
FACTorY
seTTings
TrAp ip
ADDress
LoCAL seTup uniT nAme
En
15
System
Local Setup
IP Address: The IP address for the unit.
Network Mask: The network mask for the subnet to which the unit is con-
nected.
Gateway: The gateway for the network to which this unit is connected.
Trap IP
The IDLV-5100P provides a Monitor Center IP address. You can set this to be
the same IP address of the Monitor Center, which is typically a PC in order to
allow the device to send messages to the monitor center.
Unit Name
The IDLV-5100P allows you to edit the unit name which is displayed on the front
panel LCD. Default name is ‘Digital TV Processor”. The unit name should be
within 20 characters in ASCII format.
Properties
Main Version: Show software version of this device
MAC Address: Factory-set MAC address which is guaranteed to be unique.
You cannot congure this address.
Linux OS version: Show Linux OS version
ARM SW version: Show ARM software version
Decoder version: Show Decoder version
FPGA version: Show FPGA version
TS/IP IN (or OUT) NIOS: The mode of the TS/IP board - “IP Out” or “IP IN”.
TS/IP IN (or OUT) FPGA: The mode of the TS/IP board - “IP Out” or “IP IN”.
Factory
Settings
All the user congurable parameters will be set to the factory default settings,
including IP address and the unit name.
O p t i o n a l
Function
External Board Type: Press <ENTER>-key to active the menu. After the opera-
tion, you need reboot the unit to valid the conguration.
100M Single In: The TS/IP port is congured as input, you can feed transport
stream over IP into the unit. The menu ‘Ethernet’ will be showed under the
inputs menu. This option is specialized for IDLV-5100P-44x model.
100M Single Out: The TS/IP port is congured as output, you can set the
transport stream over IP output to the IP network. The menu ‘Ethernet’ will
be showed under the outputs menu. This option is specialized for megabit
modelIDLV-5100P-44x model.
100M Dual Out: The TS/IP port is congured as output, you can set the
transport stream over IP output to the IP network. The menu ‘Ethernet’ will be
showed under the outputs menu. This option is specialized for IDLV-5100P-43x
model.
1000M In&Out: Select the option to enable the full duplex gigabit IP port. The
menu ‘Ethernet’ will be showed under the main menu. This option is available
for IDLV-5100P-46x model.
No Exist: The TS/IP port is invalid. Therefore the menu ‘Ethernet’ will not be
showed anywhere.
Mux Function: Press <ENTER>-key to active the menu, use < > < >-keys to
congure the Mux functional block as ‘Enable’ or or ‘Disable’. Press <ENTER>-
key to conrm or to scrap by pressing <EXIT>-key.
Backup Function: Press <ENTER>-key to active the menu, use <↑> <↓>-keys
to congure the Backup function as ‘Enable’ or or ‘Disable’. Press <ENTER>-
key to conrm or to scrap by pressing <EXIT>-key.
LCD Switch: There are two options: Always On and Power saving. Always On
option means the front panel will always be lightened. Power Saving means the
front panel will be off after a while if there’s no operation.
HTTP Login
Modify the username and password for the WEB management.
The default username: root
The default password: 12345
M a c h i n e
Type
Reserved.
16
This following menu is only available on IDLV-5100P-46x model:
TS over
IP
IP Out
IP Out switch: Enable or disable the IP output.
IP Out status: Show IP packets per second, UDP packets/s, Column FEC
packets/s, Row FEC packets/s
Protocol: You can select the transport protocol from UDP and RTP.
TS pkts per UDP: Set the number of the TS packages encapsulated in one
UDP package. The valid range goes from 1 to 7.
Time to Live: Set the number of the routers over which the TS over IP can be
transmitted. The valid range goes from 1 to 255.
Type of Service: You can select from normal, Min monetary cost, Max reliabil-
ity, Max throughput, Min delay
TS source: Select the source of the transport stream over IP streaming output.
There are 5 type of source optional: ASI1 Input, ASI2 Input, CI De-encrypted,
TUNER, Mux TS.
Uni/Multicast Address: Enter the IP address of the multicast stream for the
transport stream over IP.
Uni/Multicast UDP port: Enter the UDP port number of the TS over IP stream.
ProMPEG FEC: Enable/Disable: Enable or disable ProMPEG FEC function.
Column FEC UDP port: You can set Column FEC UDP port number
Row FEC UDP port: You can set Column FEC UDP port number
Mode(1D:column, 2D:row+column, 5X5: the size of matrix)
1D. 5X5 Support packet loss : 5/1000package
1D. 5X20 Support packet loss :20/1000package
1D. 10X10 Support packet loss :10/1000package
2D. 5X5 Support packet loss :5/1000package
2D. 5X20 Support packet loss :20/1000package
2D. 10X10 Support packet loss :10/1000package
FEC Alignment: You can select from Annex A or Annex B
Note: Only when this option is enabled and the IP Out protocol is set to RTP,
the following options are valid.
IP In
IP in status: You can check the IP In status of the unit in this option.
RTP/UDP: It will display the transport protocol.
Column FEC;Row FEC: it will display the Column FEC and Row FEC value.
Both value will be less than 20.
Packets per UDP frame: it will display Packets per UDP frame.
Received TS frames: it will display the TS frames received by the IP port. The
value is accumulated.
Fixed RTP frames: It will display the Fixed RTP frames.
Note: Above sub-menus only appears when the IP in status is set as Locked.
Uni/Multicast Address: Enter the IP address of the multicast stream for the
transport stream over IP.
Uni/Multicast UDP port: Enter the UDP port number of the TS over IP stream
Column FEC UDP port: Enter the Column FEC UDP port number
Row FEC UDP port: Enter Row FEC UDP port number
TS clock recovery: Select the TS clock recovery mode from Auto or Fixed rate.
Note: If the TS contains PCR, you can select Auto mode. If not, please select
Fixed rate.
TS Bit rate: Set the bit rate of the TS comes from the TS/IP input. The setting
range is 0—100Mbits/s.
Note: The setting TS Bit rate is only valid when the TS clock recovery is cong-
ured as Fixed Rate.
En
17
Local setting
IP address: Enter the IP address for IP board of the unit.
Subnet mask: The network mask for the subnet to which the unit is connected.
MAC address: Factory-set MAC addresses are guaranteed to be unique.
Therefore you cannot congure the address.
Gateway IP address: The Gateway for the network to which this unit is con-
nected.
Gateway MAC address: MAC address of the Gateway, to be congured by the
User.
Ethernet
Status
Link Status: shows the link speed.
18
Remote management and control
over web interface
IDLV-5100P can be controlled by WEB. User can type IP address of IDLV-5100P in browser. It will show login
pop-up. The default user name is root and password is 12345. If you forget this username and password, you
can use front panel button to change it. You can set it in System → HTTP login menu. The parameters are the
same as detailed in the previous paragraphs and tables above.
S TAT US
User can monitor the status of the outputs and inputs. You also can set auto refresh time here. “Status Refresh”
is used to refresh status manually.
En
19
TUNER INPUT
parameters for tuner input. Click “Apply” button to submit, or click “Cancel” button to cancel.
CI
Set parameters for CI slots. Click “Apply” button to submit, or click “Cancel” button to cancel.
20
DECODER
Set parameters for decoder. Click “Apply” button to submit, or click “Cancel” button to cancel.
En
21
22
OUTPUT
Set parameters for ASI outputs. Click “Apply” button to submit, “Refresh” button to refresh latest status of
settings, or click “Cancel” button to cancel.
BISS
Set parameters for BISS. Click “Apply” button to submit, or click “Cancel” button to cancel.
En
23
MUX
Set parameters for Mux. Click “Apply” button to submit, or click “Cancel” button to cancel
24
TS OVER IP
Set parameters for IP IN. Click “Apply” button to submit, or click “Cancel” button to cancel (IDLV-5100P-20x and
-44xx model only).
Set parameters for IP OUT. Click “Apply” button to submit, or click “Cancel” button to cancel (IDLV-5100P-20x
and 44xx model only):
En
25
Set parameters for IP OUT. Click “Apply” button to submit, or click “Cancel” button to cancel (IDLV-5100P-43xx
model only).
26
When DVB mode is selected the user can setup the Unicast and Multicast parameters. When clicking on the Uni/
Multicast Setup, the following screen will be displayed:
When IPTV mode is selected, clicking on the Uni/Multicast Setup button will open the following screen:
En
27
Set parameters for IP OUT. Click “Apply” button to submit, or click “Cancel” button to cancel (IDLV-5100P-46xx
model only)
Set parameters for IP IN. Click “Apply” button to submit, or click “Cancel” button to cancel (IDLV-5100P-46xx
model only)
28
Set parameters for Local setting. Click “Apply” button to submit, or click “Cancel” button to cancel (IDLV-5100P-
46xx model only)
SYSTEM
Set parameters for system. Click “Apply” button to submit, or click “Cancel” button to cancel.
En
29
30
Technical Specifications
TUNER INPUT
DVB-S/S2 Tuner Input (ISI Factory Optional)
Connector Type 1 x F type female 75Ω for Input, 1 x F type female 75Ω
for loop through output
Input Frequency Range 950~2150MHz
Input Level -25~-65dBm
Symbol Rate 2~45MBaud
Roll-off Factor DVB-S QPSK: 0.35
DVB-S2 8PSK: 0.35, 0.25, 0.2
FEC Code Rate DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 QPSK: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10
DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10
LNB Polarity Selection Voltage 0, 13V, 18V selectable
LNB Band Selection Tone 0/22KHz selectable
Satellite Selection Command DiSEqC 1.0
ISI ID 1 ~ 255 user congurable
DVB-C Tuner Input
Connector Type 1 x F type female 75Ω for Input, 1 x F type female 75Ω
for loop through output
Input Frequency Range 48~862MHz
Input Level 45~75dBuV
Symbol Rate 1~7MBaud (ITU J.83 Annex A)
Constellation 16/32/64/128/256QAM
Bandwidth 6MHz/7MHz/8MHz
Input Return Loss 7dB (typ.)
DVB-T/T2 Tuner Input
Connector Type 1 x F type female 75Ω for Input, 1 x F type female 75Ω
for loop through output
Input Frequency 104~862MHz (VHF/UHF)
Input Level -20 ~ -70dBm
Constellation DVB-T: QPSK/16-QAM/64-QAM
DVB-T2: QaPSK, 16QAM, 64QAM, 256QAM
Bandwidth 6MHz/7MHz/8MHz
FFT Mode DVB-T: 2K/8K
DVB-T2: 1K, 2K, 4K, 8K, 16K, 32K
Guard Interval DVB-T: 1/4, 1/8, 1/16, 1/32
DVB-T2: 1/4, 5/32, 1/8, 5/64, 1/16, 1/32, 1/64, 1/128
FEC Code Rate DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8
DVB-T2: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6
Input Return Loss 7dB (typ.)
ASI INPUT
Connector Type 2 × BNC female, 75Ω
Standard DVB-ASI, EN50083-9
Input Bit Rate ≤ 100Mb/s
DS3 INPUT (OPTION)
Connector Type 2 × BNC Female, 75Ω, including loop through
Standard Compliant with ITU-T G.703
Frame Structure Compliant with ITU-T G.752 and ITU-T G.804
Bit Rate 44.736Mb/s
TS OVER IP
Connector Type 1 x RJ-45, 10/100 Base-T or 100/1000 Base-T for TS/IP
Effective Bit Rate 70Mb/s for 10/100 Base-T, 800Mb/s for 1000 Base-T
Protocol UDP / RTP, Multicast / Unicast, IGMPv2, ARP
TS PROCESSING
TS Input Management Demux and Remux among Tuner / DS3 (optional) / E3
(optional), ASI and TS/IP inputs
TS Output Management Demux and Remux for 2 independent ASI outputs
En
31
Service and PID Management Remux, ltering and remapping
PSI/SI PSI/SI table regeneration, NIT and SDT edition, LCN
Edition and Re-generation
Descrambler DVB Common Scrambling Algorithm (CSA)
BISS Mode BISS-1, BISS-E
Common Interface Double PCMCIA slots, compatible with major CA CAMs
in the market
ASI OUTPUT
Connector Type 2 pairs of BNC female, 75Ω
Standard DVB-ASI, EN50083-9
Output Bit Rate ≤ 99Mb/s
TS Processing 2 Independent TS Re-multiplexed from tuner, TS/IP and
2 ASI inputs
HDMI OUTPUT
Standard 1x HDMI 1.3 interface (up to 1080i)
Video Resolution and Frame Rate 1080i x 30, 1080i x 29.97, 1080i x 25, 720p x 60, 720p
x 59.94,720p x 50, 480p x 60, 576p x 50, 576i x 25,
480i x 29.97
Audio Embedded 2x stereos or compressed data pass through*
DIGITAL VIDEO PROCESSING
Video Standard MPEG-2(MP@ ML for SD, MP@HL for HD)
MPEG 4/H.264 AVC Part 10 (MP@L3 for SD, HP@L4.1
for HD)
SDI Video Resolution 1080i x 30, 1080i x 29.97, 1080i x 25, 720p x 60
720p x 59.94, 720p x 50, 576i x 25, 480i x 29.97
Video PID Bit Rate < 80Mb/s
HD/SD-SDI Output
Connector Type 1 pair of BNCs (mirrored) , female, 75Ω
SD Standard SMPTE 259M, 270 Mb/s (10bit)
HD Standard SMPTE 292M, 1.485 Gbit/s (10bit)
Level 800mV p-p
DIGITAL AUDIO PROCESSING
Connector Type 2 x D-sub 9 male with XLR adaptor cables
Number of Output 2 x audio are decoded or passed through
Audio Sampling Rate 32, 44.1 and 48KHz
Audio Bit Rate 32, 64, 96, 128, 160, 192, 224, 256, 288, 320, 352, 384,
416 and 448 kb/s for MPEG-1 Layer I
32, 48, 56, 64, 80, 96, 112, 128, 160, 192, 224, 256,
320 and 384 kb/s for MPEG-1 Layer I
Nominal Output Level 1Vp-p (with standard test stream)
Output Format AES/EBU
Load Impedance 110Ω (with XLR adaptor cable)
ANALOG VIDEO OUTPUT
YPbPr Connector 1 set of RCA female, 75Ω
CVBS Connector 1 × BNC female 75Ω, 1 x RCA female 75Ω
CVBS Standard NTSC, PAL, and SECAM
YPbPr Resolution 1080i x 30, 1080i x 29.97, 1080i x 25, 720p x 60, 720p
x 59.94, 720p x 50, 480p x 60, 576p x 50, 576i x 25,
480i x 29.97
Nominal Output Level I.0 Vp-p±5% (with standard test stream)
Frequency Response <±I dB, at 5.5 MHz for PAL/SECAM, 4.2MHz for NTSC
and 15MHz for HD YPbPr
Chroma-Luma Delay <±30 ns
Field Time Distortion <2%
Line Time Distortion < 1%
Short Time distortion <2%
Differential Gain <3%
Differential Phase <2°
Signal to Noise Ratio >55 dB (luminance weighted)
32
ANALOG AUDIO OUTPUT
Connector type 2 x D-sub 9 male, with XLR adaptor cable
Output Impedance 600Ω (balanced)
Output mode Left, Right, Dual Mono, Stereo
Number of Outputs 2 pairs of stereo audio outputs 2 pairs of stereo audio
outputs (2 Audio PIDs or 4 channels are decoded)
Cross Talk Among Channels >70dB
THD <0.3% @ 400Hz, 1KHz test tone
Frequency Response ±0.5dB over 20Hz ~ 18KHz
Output Level 0dBm in 600Ω (0dBu), adjustable range ±I0dB
ANCILLARY DATA PROCESSING
Subtitle DVB/EBU
VBI Teletext, WSS, VFD, VPS
Closed Caption EIA 608, EIA 708, EIA 608-to-708
REDUNDANCY
Redundancy Port among Tuner, 2 x ASI inputs and TS/IP
Switching Condition TS Sync Loss
Switching Mode Main, Spare
CONTROL & MONITORING
Connector Type 1×RJ-45, 10/100 Base-T, for equipment IP Control
Remote Control SNMP, HTTP (Web Interface), Proprietary HDMS
(Headend Device Management System)
Local Control LCD display and 6-key keypad
Serial Port 1×RS-232 D-sub female, for debug use only
Equipment Upgrade Embedded FTP loader and Telnet
PHYSICAL
Dimension 44mm×483mm×255mm
Weight 3.4Kg Net, 5.4Kg Gross
Power Supply AC 90V~260V, 50/60Hz
Power Consumption 24W (exclusive of LNB power)
Operating temperature 0~+45°c
Storage temperature -10~+60°c
Operating Humidity 20~90%, non-condensed
En
33
Default Device Parameters On
Delivery
Main menu Sub - m en u
Parameter
Factory defaul settings
Input
Status
ASI1 unlock
ASI2 unlock
TUNER unlock
DVB-S2
This menu is displayed only on IDLV-5100P-xxS2 model
LNB Frequency: 5150MHz
Satellite Frequency: 4000MHz
Symbol Rate: 26850KBaud
LNB Voltage: OFF
LNB 22KHz: OFF
DISQEC: DISQEC OFF
PLS Gold Code: 0
Frequency Offset High: 5000KHz
Frequency Offset Low: -5000KHz
COFDM
This menu only is shown on IDLV-5100P-xxT model
Frequency: 794MHz.
Bandwidth: 6M
DVB-T2
This menu only is shown on IDLV-5100P-xxT2 model
Frequency: 794MHz.
Bandwidth: 6Mhz
QAM
This menu only is shown on IDLV-5100P-xxC model
Constellation: 64.
Fequency: 50000KHz.
Symbol Rate: 6875KBaud.
E3_G.703/
DS3
TThis menu only is shown on IDLV-5100P-xxDS3/E3 model
Input Type: Normal
RSSI
Displays the quality of the received DVB-S2 signal.
Ethernet
This menu only is shown on IDLV-5100P-44x models which set TS/IP streaming board
as “100M Single IN”
Stream IP Addr: 16.16.16.16
Stream Netmask: 255.255.255.0
Stream Gateway: 1.0.0.0
Stream Mac Address: factory-set MAC addresses.
Multicast IP Addr: 0.0.0.0
Multicase UDP Port: 3000
Protocol: UDP
Output Smoothing: Auto
TS Bit Rate: 38000Kbps
Output
Decoder
Status: Video: Unknown Error Audio: Unknown Error
PMT: --- PN:--- V:---A1:---A2:---
TS_ID: ---- PCR_PID: ----
Service Name: ---- Service Type: ----
Audio1 Format: ---- Audio2 Format: ----
Service Provider: ----
34
Output
Decoder
Source: 0-ASI1 input
Program: No selected
Video:
Video Standard: Auto
Screen: Auto
DVB Subtitle Lang: eng.
EBU Subtitle Lang: eng.
Subtitle Priority: DVB rst.
Fail Mode: Black Screen.
Closed Caption: off.
VBI Mode: disable
CVBS Sub PAL: PAL-B/D/G/H/I
CVBS Sub NTSC: NTSC-M
Audio:
Audio1 Level: 99
Audio1 Mode: Stereo
Audio1 Priority: eng 0/unknown
Audio2 Level: 99.
Audio2 Mode: Stereo
Audio2 Priority: chn 0/unknown
HDMI/AES Embeded: PCM
Mode: Manual Selection
A/V Alarm Switch:
Video Alarm: enable
Audio Alarm: enable
ASI1 ASI1 Source: ASI1 input
ASI2 ASI2 Source: ASI1 input
SDI
Embeded Audios: On
Closed Caption Mode: Auto
AC-3 Pass Thru CH: Channel 5-6
Ethernet
This menu only is shown on IDLV-5100P-44x models which set TS/IP streaming board
as “100M Single IN” and IDLV-5100P-43x which set TS/IP streaming board as “100M
Dual Out”.
Stream IP Addr: 10.10.10.10.
Stream Netmask: 255.255.255.0
Stream Gateway: 10.10.10.1
Stream Mac Address: Factory-set MAC addresses
Gateway Mac Address: FF:FF:FF: FF:FF:FF.
If the unit is IDLV-5100P-43x which is set as “100M Dual Out” in the system menu,
two menus will appear and each contains above ve setups so you can set the two IP
output separately
TS/IP1: This sub-menu contains ve items: Stream IP Addr, Stream Netmask, Stream
Gateway, Stream Mac Address and Gateway Mac Address. The setup method is the
same as above.
TS/IP2: The same as TS/IP1.
Protocol: UDP
TS Pkts Per UDP: 7
Time To Live: 255
Type of Service: Normal
Source: ASI1 Input
Mode: DVB
Uni/Multicast Setup:
Multicast IP: 225.1.1.1•
Multicast UDP Port: 3000•
Target MAC address: Mac address of your target device•
En
35
Output
Mux
This menu is shown only when the Mux function block is enabled and turned
on.
Mux Switch: Off
Bit Rate: 50000Kbps
Output Bit Rate: 0Kbps
TS ID: 1.
Program List: 0-TS invalid
E3_G703
This menu only is shown on IDLV-5100P-xxDS3/E3 model
E3_G.703 Source: ASI1 Input
E3_G.703 Protocol: Framer MSB
DS3 The contents of DS3 menu are the same as E3_G703
System
Local Setup
IP Address: 10.10.70.48
Network Mask: 255.255.255.0
Gateway: 1.0.0.0
Trap IP
10.10.70.1
Unit Name Digital TV Processor
Properties
Main Version: 51PRxxxx
MAC Address: xx:xx:xx:xx:xx:xx
Linux OS version: xx
ARM SW version: xx
Decoder version: xx
FPGA version: xx
TS/IP IN (or OUT) NIOS: xx.
TS/IP IN (or OUT) FPGA: xx
F a c t o r y
Settings
O p t i o n a l
Function
External Board Type: 100M Single Out or 100M Dual Out or 1000M In&Out or
No Exist basing on different models
Mux Function: Enable
Backup Function: Disable
LCD Switch: Disable
HTTP
Login
The default username: root
The default password: 12345
M a c h i n e
Type
Reserved
36
**For IDLV-5100P-46x model only:
TS over IP
IP Out
IP Out switch: Enable
IP Out status: Show IP packets per second, UDP packets/s, Column FEC
packets/s, Row FEC packets/s
Protocol: UDP
TS pkts per UDP: 7.
Time to Live: 255.
Type of Service: Normal
TS source: ASI1 Input
Uni/Multicast Address: 224.1.1.1
Uni/Multicast UDP port: 1234
IP In
IP in status: Bitrate
Uni/Multicast Address: 224.1.1.1
Uni/Multicast UDP port: 1234
Column FEC UDP port: 1236
Row FEC UDP port: 1238
TS clock recovery: Auto
L o c a l
setting
IP address: 10.10.10.10.
Subnet mask: 255.255.255.0
MAC address: Factory-set MAC addresses
Gateway IP address: 9.9.9.9
Gateway MAC address: FF:FF:FF: FF:FF:FF
E t h e r n e t
Status
Link Status: Disconnected
En
37
Safety
CAUTION
Unauthorized maintenance or the use of non-approved replacements may affect the equipment specication
and invalidate any warranties.The device should be kept away from electric, strong magnetic and hot areas
(temperature < 40°C; humidity < 85%).
IDLV -5100P Professional Multi-format SD/HD Integrated Receiver Decoder
Enter Exit
Power Tuner Lock Alarm
Keep away from high electric and magnetic areas
Don’t keep the device in the dusty, humid and high-temperature environment. Don’t let the petrol, thinner, insecti-
cide or other volatile substances touch the shell of device. Please use soft cloth to wipe the device tenderly.
IDLV -5100P Professional Multi-format SD/HD Integrated Receiver Decoder
Enter Exit
Power Tuner Lock Alarm
Avoid eroding
If the device is connected well with power and cables but the picture is still not good, please contact with the
supplier or dealer. Please don’t dismantle the device or repair it by yourself.
IDLV -5100P
Professional Multi-format SD/HD Integrated Receiver Decoder
Enter Exit
Power Tuner Lock Alarm
Do not dimantel the device
×
It is better to use the AC regulated power supply in the area where the voltage is unstable.
IDLV -5100P Professional Multi-format SD/HD Integrated Receiver Decoder
Enter Exit
Power Tuner Lock Alarm
~220 ±10%
The device must be grounded well.
IDLV -5100P Professional Multi-format SD/HD Integrated Receiver Decoder
Enter Exit
Power Tuner Lock Alarm
Device must be well grounded
38
Warranty, service and support
This Limited Warranty applies only to the Product sold by Inverto Digital Labs, 18 Duchscherstrooss, L-6868
Wecker, Luxembourg (hereby, the “Company”) the Customer purchase for his own use and not for resale. The term
“Product” in this Limited Warranty does not include any software programs, whether pre-loaded with the Product,
installed subsequently or otherwise.
1. Disclaimer and exclusion
except as specied in this limited warranty, the foregoing warranties are given and accepted in lieu of any and all
other warranties or conditions, express or implied, including, but not limited to, the implied warranties or conditions
of merchantability and tness for a particular purpose.
to the extent an express or implied warranty cannot be excluded in some states or juridictions, the above exclusion
may not apply. in that event, such warranties are limited in duration to the warranty period. no warranties apply
after that period.
because some states or jurisdictions do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply.
this limited warranty gives customer specic legal rights, and customer may also have other rights which vary from
jurisdiction to jurisdiction.
customer is advised to consult applicable state or country laws for a full determination of your rights.
This disclaimer and exclusion shall apply even if the express warranty set forth below fails of its essential
purpose.
2. Limitations of Liability
Under no circumstances shall the Company or its supplier be liable for (a) damage to, or loss or corruption of
programs, data or media, or (b) any damages whatsoever (including, but not limited to, direct or indirect damages,
loss of business prots, lost savings or other special, incidental, exemplary or consequential damages whether
for breach of warranty, contract, strict liability, tort) arising out of or resulting from the use of or inability to use the
products and/or the enclosed written materials or the provision of or failure to provide support services, even if the
Company, its supplier, an authorized Company representative, service provider or dealer have been advised of the
possibility of such damages or of any claim by any third party. Any liability of the Company or its supplier which is
not excluded shall be limited to the purchase price of the Product.
Some jurisdictions do not allow the limitation of incidental or consequential damages so this limitation may not
apply fully to the Customer, but such limitation shall apply to the maximum extent permitted by applicable law.
3. Application of the Warranty
The Company warrants the Product against critical failure resulting from original manufacturing defects in
workmanship or material, under normal use. The company does not warrant any uninterrupted or error-free
operation of the product or that all deciencies, errors, defects or nonconformities will be corrected.
Unless the company species otherwise, this warranty extends only for the original user of the Product and the
Warranty applies only in the country or region in which the original user purchases the Product to the Company or
a Company Reseller in case of a resale.
4. Warranty period
The warranty period of the Product is 24 months. The warranty period for the Product starts at the day of purchase
(purchase invoice date) of the Customer, and in case of a resale by the Company Reseller not more than 45 days
after the production date marked on the Product.
This Limited Warranty extends only to the original end-user purchaser of the Product and is not transferable to
anyone who obtains ownership of the Product from the original end-user purchaser.
5. Limited Warranty Exclusions
This Warranty with respect to the Customer’s Product is subject to the following exclusions:
(i) Failure or damage resulting from misuse (including but not limited to use of any Product capacity or capability,
other than that authorized by the Company in writing), accident, modication, unsuitable physical or operating
environment, or improper maintenance by the Customer;
(ii) Failure caused by a Product for which the Company is not responsible;
(iii) Any non-Company Products, including those provided with, or installed on, a Company Product at the Customer
request;
(iv) Accessories, supply items and consumables (e.g. batteries), and structural parts (e.g. frames and covers);
(v) Service of Product alterations;
(vi) Service of a Product on which the Customer is using capacity or capability, other than that authorized by the
Company in writing;
(vii) Any Product not manufactured by or for the Company, or sold to an end-user in a country not covered under
this Warrant
En
39
(viii) Loss of any, or damage to, programs, data, or storage media. The Company may opt to replace the Product
submitted for warranty services and, thus, any data stored on the original Product may become permanently
inaccessible.
This Limited Warranty is voided by removal or alteration of identication labels on the Product or its parts.
Any technical or other support provided for a Product under warranty, such as, “How to” questions and those
regarding the product set-up and installation, is provided WITHOUT WARRANTIES OF ANY KIND.
The Company is not liable for any transport/delivery/insurance costs, import duties, taxes, licensing fees and any
charges from telephone/fax communication as consequence of the failure of the Product.
6. Service during the warranty period
In the event the Product is found to be defective within the warranty period, Customer’s sole and exclusive remedy
and the entire liability of the Company under this Limited warranty will be, at the Company or its Service Center,
at its option:
(1) Repair the Product by means of remote support such as, but not limited to, telephone, email support.
(2) Upon the product return to the party supplying it to the Customer, freight an insurance prepaid - repair or replace
any defective Product or parts of the Product thereof covered by the Warranty with new or factory-refurbished
Products or parts that are equal to new products in performance.
7. To get the Limited Warranty service
In the event that a warranty service is required, you should contact your specialist dealer or the point of sale.
Warrantee claims cannot be made directly to the company - Inverto Digital Labs. You should therefore keep your
sales receipt as proof of purchase. The Company recommends the Customer rst utilize support material shipped
with the product, product diagnostics, information contained on the Web, and online support on http://www.inverto.
tv/support.
If unsuccessful to obtain service under this warranty, the Customer must notify the Company Technical Support or
its authorized Service Center representative of the defect before the expiration of the warranty period. Customers
will provide appropriate assistance to the Telephone Support personnel to resolve issues.
If the technical support is unsuccessful, The Company or its authorized Service representative will instruct the
customer on how to receive warranty repair.
If the Customer does not know of a Company authorized service center for the Company’s product, it should
contact the reseller. If the reseller is an authorized service center, they will arrange for repair.
If the Customer reseller is not a Company authorized Product’s service center, they will direct the customer to an
authorized service center.
The Company reserves the right to charge for service in exception cases.
8. Governing Law
The Customer and the Company consent to the application of the laws of Luxembourg, to govern, interpret, and
enforce all of the Customer and the Company’s rights, duties, and obligations arising from, or relating in any
manner to, the subject matter of this Statement of Limited Warranty, without regard to conict of law principles.
9. Jurisdiction
All of our rights, duties, and obligations are subject to the courts of Luxembourg.
V171111
… 34 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Inverto IDLV-5100P bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Inverto IDLV-5100P in de taal/talen: Engels als bijlage per email.

De handleiding is 4,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info