Handleiding Inventor V5MFI32-60 (pagina 29 van 136) (Engels)

771744

Verklein

Vergroot

Pagina terug

1/136

Pagina verder

 Page 28 

Drain Joint Installation

NOTE: Make sure the water drains to a safe

location where it will not cause water

damage or a slipping hazard.

Seal

Drain joint

(A) (B)

Base pan hole of

outdoor unit

Seal

Fig. 9.7

Notes On Drilling Hole In Wall

You must drill a hole in the wall for the

refrigerant piping, and the signal cable that will

connect the indoor and outdoor units.

Determine the location of the wall hole

based on the location of the outdoor unit.

Using a 65-mm (2.5”) core drill, drill a hole

in the wall.

NOTE:

When drilling the wall hole, make

sure to avoid wires, plumbing, and other

sensitive components.

Place the protective wall cuff in the hole.

This protects the edges of the hole and will

help seal it when you nish the installation

process.

Fig. 9.6

300 cm / 118” or more

60 cm / 23.6”

or more

150 cm / 59”

or more

25 cm / 9.8”

or more 25 cm / 9.8”

or more

If the drain joint comes with a rubber seal

(see Fig. 9.7 - A ), do the following:

1. Fit the rubber seal on the end of the drain joint

that will connect to the outdoor unit.

2. Insert the drain joint into the hole in the base

pan of the unit.

3. Rotate the drain joint 90° until it clicks in place

facing the front of the unit.

4. Connect a drain hose extension (not included)

to the drain joint to redirect water from the

unit during heating mode.

If the drain joint doesn’t come with a rubber

seal (see Fig. 9.7 - B ), do the following:

1. Insert the drain joint into the hole in the base

pan of the unit. The drain joint will click in

place.

2. Connect a drain hose extension (not included)

to the drain joint to redirect water from the

unit during heating mode.

 Page 29 

The drainpipe is used to drain water from the

unit. Improper installation may cause unit and

property damage.

• Insulate all piping to prevent condensation,

which could lead to water damage.

• If the drainpipe is bent or installed

incorrectly, water may leak and cause a

malfunction of the water- level switch.

• In HEAT mode, the outdoor unit will

discharge water. Ensure that the drain hose

is placed in an appropriate area to avoid

water damage and slippage due to frozen

drain water.

• DO NOT pull the drainpipe forcefully as this

could cause it to disconnect.

NOTE ON PURCHASING PIPES

This installation requires a polyethylene tube

(outside diameter = 3.7-3.9cm, inside diameter

= 3.2cm), which can be obtained at your local

hardware store or from your dealer.

Indoor Drainpipe Installation

1. Make sure the drain pipe is connected to the

outdoor side downward.

The hard polyvinyl chloride(PVC)plastic pipe

(external diameter 26 mm) sold in the market

is suitable for the attached soft drain pipe.

4. After the Drain Pipe has been connected,

please check if the water drains out of the

pipe efciently and has no leakage.

5. Refrigerant Pipe and Drain Pipe should be

heat-insulated to avoid condensing and

water-dropping later on.

3. Please connect the Soft Drain Pipe with the

Drain Pipe, then x it with band; if you have

to connect the Drain Pipe indoors, to avoid

condensing caused by air intake, you must

cover the pipe with heat-insulation material

(polyethylene with Specic Gravity of 0.03, at

least 9 mm in thickness), and use Glue Band

to x it.

Fig. 10.1

Drainpipe Installation 10

6. Using a 65-mm (2.5”) core drill, drill a hole in

the wall. Make sure that the hole is drilled at a

slight downward angle, so that the outdoor

end of the hole is lower than the indoor end

by about 1cm (0.4”). This will ensure proper

water drainage (See Fig. 10.2). Place the

protective wall cuff in the hole. This protects

the edges of the hole and will help seal it

when you nish the installation process.

Wall

Indoor

Outdoor

≈ 0.5~1cm

/ 0.2~0.4 inch

Fig. 10.2

NOTE: When drilling the wall hole, make sure

to avoid wires, plumbing, and other sensitive

components.

Pass the drain hose through the wall hole.

Make sure the water drains to a safe location

where it will not cause water damage or a

slipping hazard.

NOTE: The drainpipe outlet should be at least

5cm (1.9”) above the ground. If it touches the

ground, the unit may become blocked and

malfunction. If you discharge the water directly

into a sewer, make sure that the drain has a U

or S pipe to catch odors that might otherwise

come back into the house.

Drain pipe

Glue

Band for covering the pipe

CAUTION

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Inventor V5MFI32-60 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Inventor V5MFI32-60

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info