686044
18
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
264
A
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
OWNER’S MANUAL
PureSpa™
SJB-HS-20 / SJB-HS-22
SJB-HS-30 / SJB-HS-33
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
264-*A*-R2-1610
Do not forget to try these other ne Intex products: pools, pool
accessories, in-home toys, airbeds and boats available at ne
retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves
the right to change speci cations and appearance, which may
result in updates to the instruction manual without notice.
For illustrative purposes only.
©2015 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte
vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/
Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in
Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex
Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne
par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading B.V., Venneveld 9, 4705 RR
Roosendaal – The Netherlands
www.intexcorp.com
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 2
Warning.......................................................................................... 3-5
Parts............................................................................................... 6-7
Product Information & Speci cations........................................ 8
Set-up............................................................................................. 8-11
Salt Level Information.................................................................. 12
Operation....................................................................................... 13-14
LED Code Chart............................................................................. 15
Maintenance and Chemicals........................................................ 16-23
Storage........................................................................................... 23
Troubleshooting............................................................................ 24-26
Warranty......................................................................................... 27
TABLE OF CONTENTS
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 3
IMPORTANT SAFETY RULES
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following.
READ AND FOLLOW ALL INSTRUCTIONS
The spa electrical appliance should be supplied through a residual current device (RCD) having a
rated residual operating current not exceeding 10 mA. If a leakage current of more than 10mA is
detected, the RCD will operate and cut-off the power supply, in such case, unplug and stop using the
spa at once. You must contact the local service center for assistance and/or repair of the product.
Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V,
must be inaccessible to a person in the spa.
Electrical installation shall ful ll the requirements of local national standards.
Parts incorporating electrical components, except remote control devices, must be located or xed so
that they cannot fall into the spa.
To reduce the risk of injury, do not permit children to use this product unless they are closely
supervised at all times.
Children should not use spas or hot tubs without adult supervision.
To reduce the risk of child drowning, supervise children at all times. Attach and lock spa cover after
each use.
To reduce the risk of injury:
a) The water in a spa should never exceed 40°C (104°F). Water temperatures between 38°C (100°F)
and 40°C (104°F) are considered safe for a healthy adult. Lower water temperatures are
recommended for young children and when spa use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal damage during the early
months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures
to 38°C (100°F).
c) Before entering a spa or hot tub, the user should measure the water temperature with an accurate
thermometer since the tolerance of water temperature-regulating devices varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with
the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory
system problems, or diabetes should consult a physician before using a spa.
f) Persons using medication should consult a physician before using a spa since some medication may
induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.
DANGER
WARNING
Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by
children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at
all times.
Risk of drowning. Inspect the spa cover regularly for leaks, premature wear and tear, damage, or
signs of deterioration. Never use a worn or damaged cover: it will not provide the level of protection
required to prevent unsupervised access to the spa by a child.
Risk of injury. Replace damaged cord immediately. Do not bury cord.
Risk of Electric Shock. Do not permit any electric appliance, such as a light, telephone, radio, or
television, within 3.5 m (11.5 feet) of a spa or hot tub.
Risk of Electric Shock. Do not use and unplug the spa when it is raining, thundering or lightning.
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 4
g) People using medications and/or having an adverse medical history should consult a physician
before using a spa or hot tub.
h) Check with a doctor before use if pregnant, diabetic, in poor health, or under medical care.
People with infectious diseases should not use a spa or hot tub.
To avoid injury exercise care when entering or existing the spa or hot tub.
Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness
and possible drowning.
Pregnant and possible pregnant women should consult a physician before using a spa or hot tub.
Water temperature in excess of 38ºC degree may be injurious to your health.
Do not use a spa or hot tub immediately following strenuous exercise.
Prolonged immersion in a spa or hot tub may be injurious to your health.
When pregnant, soaking in hot water for long periods can harm your fetus. Measure the water
temperature before entering. Do not enter spa if water is hotter than 38°C (100°F). Do not stay in
spa for longer than 10 minutes.
Spa heat in conjunction with alcohol, drugs, or medication can cause unconsciousness.
Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyperthermia and
unconsciousness.
The causes, symptoms, and effects of hyperthermia may be described as follows: Hyperthermia
occurs when the internal temperature of the body reaches a level several degrees above the normal
body temperature of 37°C (98.6°F). The symptoms of hyperthermia include an increase in the
internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of
hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub;
unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa
or hot tub; and unconsciousness resulting in the danger of drowning.
The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs
and spas.
Always add chemicals to water, never add water to chemicals. Adding water to chemicals may cause
strong fumes or violent reactions and hazardous chemical spray.
Never jump or dive into a spa or any shallow body of water.
Assembly and disassembly by adults only.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and maintenance must be performed
by an adult above 18 years old, and who is familiar with the risk of electric shock.
No part of the electrical appliance is to be located above the bath during use.
Keep the plug of this product more than 4m away from the spa and at a height of 1.2m at least.
Always unplug this product from the electrical outlet before removing, cleaning, servicing or making
any adjustment to the product, and on raining days.
Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge
trimmers and other equipment.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
quali ed persons in order to avoid a hazard. Use only identical replacement parts when servicing.
Always keep plug dry, plug in with wet plug is de nitely forbidden!
The spa must be supplied by earthed power source.
WARNING
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 5
CAUTION
Maintain water chemistry in accordance with manufacturer’s instructions.
1. Press the RESET button on the RCD.
2. Turn on the spa electrical equipment.
3. Press the TEST button on the RCD. The RCD indicator should
turn off and the electrical equipment should shut off. If the RCD
indicator does not turn off, and the electrical equipment does not
shut off, the RCD is faulty. Do not use the spa. Contact a quali ed
electrician to correct the fault.
4. Press the RESET button on the RCD. The indicator on the RCD
should turn on. If the RCD indicator does not turn on, the RCD is
faulty. Do not use the spa. Contact a quali ed electrician
immediately to correct the fault.
WARNING
TEST
RESET
RESET
TEST
TEST
RESET
RESET
TEST
TEST
To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter
plugs to connect unit to electrical supply; provide a properly located outlet.
Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
Do not leave the spa empty for extended period of time. Do not expose the spa under direct
sunshine.
When the appliance is not in use for long period of time, such as in the winter, the spa set should be
disassembled and stored indoor.
Adequate drainage system must be provided around the spa to deal with over ow water.
Do not allow the water in the spa to freeze. Do not turn on the spa when the water is frozen.
Do not use the spa if damaged in delivery and/or malfunctioning in any fashion. Contact the Intex
service center for further direction.
Never use the spa alone or allow others to use the spa alone.
Never pour water with a temperature higher than 40°C (104°F) into the spa directly.
Keep all pets away from spa to avoid any damage.
Do not add bath oil or bath salt to the spa water.
The spa must be setup on a level, at and smooth surface that is capable of supporting the maximum
load of the lled spa with four adult occupants: weight 2500 lbs (1136Kg); six adults: 3500 lbs
(1592 kg).
Provide adequate drainage system around the spa to deal with over ow water and splashes.
WARNING
This product is provided with a RCD located at the end of the power cord. The RCD must be
tested before each use. Do not use the spa if the RCD does not function properly.
Disconnect the power cord until the fault has been identi ed and corrected. Contact a quali ed
electrician to correct the fault. Do not bypass the RCD. There are no serviceable parts inside
the RCD. Opening the RCD will void the warranty.
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 6
PARTS
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
10
8
21
5
22
1
6
3
4
1213
16
11
14
26
A
B
C
A
B
C
15
23
30
29
28
20
31 32 33
2
D
27
9
24
35
34 7
18
17
19
25
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 7
When ordering parts, be sure to quote the model number and part numbers.
PARTS (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
REF. NO. DESCRIPTION QTY. PART NO.
4 ADULTS 6 ADULTS
1 CONTROL BASE 1 12096 12196
2 SPA FILTER MOTOR 1 11888 11888
3 CONTROL PANEL (INCLUDED #4) 1 11949 11949
4 CONTROL PANEL BOLT 3 11996 11996
5 PRESSURE GAUGE 1 11741 11741
6 CONTROL PANEL BOLT WRENCH 1 11053 11053
7 SPA INFLATION HOSE 1 11830 11830
8 SPA CONTROL INLET/OUTLET O-RING 2 11788 11788
9 CONTROL BASE INFLATION CAP 1 11991 11991
10 SPA DRAIN PLUG 1 11995 11995
11 SPA DRAIN VALVE ADAPTOR 1 11718 11718
12 FILTER CARTRIDGE HOUSING 1 11798 11798
13 FILTER CARTRIDGE 2 11692 11692
14 FILTER CARTRIDGE HOUSING LID 1 11797 11797
15 INLET PLUG 1 11739 11739
16 SPA TUB 1 12090 12116
17 SPA COVER 1 11951 12117
18
SPA COVER INFLATABLE BLADDER (PRE-INSTALLED IN SPA COVER)
1 11884 12114
19 GROUND CLOTH 1 11933 12110
20 ELECTROLYTIC CELL NUT WRENCH 1 11854 11854
21 TEST STRIPS 1 11855 11855
22 WRENCH 1 11742 11742
23 OUTLET PLUG 2 11782 11782
24 INFLATION HOSE ADAPTOR 1 11829 11829
25 MALE BUCKLE 8 11994 11994
26 FEMALE BUCKLE 8 11993 11993
27 SPA CONTROL AIR INLET O-RING 1 11687 11687
28 ELECTROLYTIC CELL COVER SCREW 4 11712 11712
29 ELECTROLYTIC CELL COVER 1 11890 11890
30 ELECTROLYTIC CELL COVER O-RING 1 11897 11897
31 ELECTROLYTIC CELL NUT 1 11852 11852
32 ELECTROLYTIC CELL 1 11851 11851
33 ELECTROLYTIC CELL O-RING 1 11853 11853
34 DEFLATION OUTLET CAP 1 11992 11992
35 DEFLATION HOSE ADAPTOR 1 11935 11935
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 8
PRODUCT SPECIFICATIONS
SET UP
Cord-connected spa with pump, heater, water jet, blower, control panel, built-in hard water treatment, and
sanitation system.
This product requires a minimum of 13 Amps. If the circuit breaker trips, please check that no other
appliances or other large loads are on the same circuit as the spa.
Site preparation and requirements
The spa can be installed indoor or outdoor. For household use only.
Make sure the area is free of sharp objects under or around the spa.
Provide a properly located power outlet to connect the spa and allow easy access for periodic testing of the cord
mounted RCD.
Make sure there is enough clearance around the spa for full access to the spa equipment for maintenance and/or
service.
The area shall facilitate draining purposes during long term spa storage.
Additional requirements for indoor installation
Make sure the oor can support the full weight of the lled spa with the maximum number of occupants. Check with a
quali ed contractor or a structural engineer to verify this requirement.
Make sure the oor is water resistant and non-slip surface. Do not install the spa on carpet or other materials that will be
damaged by moisture, condensation.
Do not install the spa indoors on a second oor above nished living space due to the possibility of water and humidity
damage.
Humidity is a natural side effect of indoor spa installation. The room shall be properly ventilated to allow moisture to
escape. Install a ventilating system to prevent excess condensation, moisture in the room.
Additional requirements for outdoor installation
Spa owners may need to comply with local or states laws relating to childproof fencing, safety barriers, lighting, and
other safety requirements. Contact your local building code enforcement of ce for further details.
Make sure the surface is level, at, smooth and strong enough to support the full weight of the lled spa.
Do not setup the spa on grass or dirt, as this increases the amount of debris entering the spa, and damage the spa oor.
Do not expose the spa to direct sunlight for extended period of time.
It is possible to install and leave the spa outside at a temperature not lower than 4°C (39°F) provided the water
temperature inside the spa is higher than 4°C (39°F) and the water inside the circulation system, pump, pipe are not
frozen. Put a “temp barrier mat” between the spa oor and the ground to prevent heat loss from the bottom of the spa
and to provide better heat retention.
Maximum seating capacity: 4 adults 6 adults
Water capacity: 210 gal (795 L) 290 gal (1098 L)
Inner/outer diameter: 59/79 in (150/201 cm) 66/86 in (168/218 cm)
Height: 28 in (71 cm)
Jet pump: 0.9 HP / 220-240 V / 50 Hz 0.95 HP / 220-240 V / 50 Hz
Bubble air blower: 1.1 HP / 220-240 V / 50 Hz
Filter pump ow rate: 460 gal/hr (1,741 L/hr)
Heater power: 2,200 Watts / 220-240 V / 50Hz
Temperature range: 20ºC – 40ºC (68ºF – 104ºF)
Temperature rise: 1.5-2.5ºC/hr (3ºF – 4.5ºF/hr) 1-2ºC/hr (2ºF – 3.5ºF/hr)
Number of Water Jet Nozzles: 4 6
Number of Bubble Jets: 120 140
Spa tub recommended working air pressure: 0.083 bar (1.2 psi)
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 9
SET UP (continued)
Setup the spa with at least 2 persons.
1. Move the entire package to the selected site. Do not drag the spa tub across the ground as this can
cause damage and leakage.
Open the carton carefully as this carton can be used to store the spa during long term storage or when
not in use.
2. Lay out all the parts on the ground and make sure all the parts are accounted for. For missing or
damaged parts contact the appropriate Intex Service Center listed in the separate “Authorized service
Centers” sheet.
Spa Control Unit Assembly
1. Connect the control panel (3) cable plug into the receptacle on top of the spa control base and screw in
the plug cover rmly by hand (see drawing 1). Note: Spread the ground cloth with the bubbles facing
down over the cleared area where you intend to setup your spa.
2. Screw the control panel bolts (4) with the provided bolt wrench (6) to secure the control panel (see
drawing 2).
3. Plug the spa control unit into an electrical outlet.
For indoor in ation:
In ate the Spa Tub Wall
1. Take out the ground cloth (19) and spread it over the cleared area. Then spread out the spa liner over
the ground cloth and point the drain valve towards a suitable draining area.
NOTE: Spread the ground cloth with the bubbles facing down over the cleared area where you intend
to setup your spa.
2. Unscrew the control base in ation cap (9) to reveal the air blower in ation outlet, insert one end of the
in ation hose (7) into the outlet and turn to the right to lock it (see drawing 3).
3. Unscrew the air valve cap to reveal the stem in the up position for in ation. Insert the other end of the
in ation hose (7) into the valve and turn to the right to lock it in position (see drawing 4).
4
6
2
1
12
3
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 10
SET UP (continued)
6. Disconnect the in ation hose (7) from the air valve and attach the pressure gauge (5) to the air valve.
The pressure gauge indicator should be in the green area for a properly in ated spa tub (see drawing 6).
Repeat previous steps to add more air if necessary.
7. Replace the air valve cap back.
NOTE: The cap is designed to be screwed on and off. Never exert force as this could cause the
complete internal in ation system of the valve to come loose. See “Spa Tub Air Valve Fastening” for
valve maintenance.
In ate the Spa Cover Air Bladder
1. Open the in ation valve and insert the in ation
hose
(7) into the valve; press to in ate
until it is rm to the touch but not hard (see
drawing 7).
2. Disconnect the in ation hose (7) from the air
blower in ation outlet and the valve.
3. Replace the control base in ation cap (9) back;
close and recess the in ation valve.
NOTE: If there is a need to add some air to the spa tub wall or spa cover air bladder after they have been
setup, refer to above “In ate the Spa Tub Wall” and “In ate the Spa Cover Air Bladder” sections. The cover
air bladder is preinstalled inside the spa cover. If it needs to be reinstalled, place the unin ated air bladder
inside the spa cover lip before in ating the bladder.
5
4
7
1 2
6
5
1
2
3
9
24
4. Press the button to turn on the control unit panel buttons rst. Press the button to in ate the
spa tub wall until it is rm to the touch but not hard (see drawing 5).
IMPORTANT: Do not over in ate or use high pressure air compressor to in ate.
5. Press the button again to turn it off.
7
7
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 11
SET UP (continued)
De ation
For Spa Tub Wall:
1. Unscrew the cap to reveal the stem, push the stem in
and turn 90 degree right to secure it in the down
position
(see drawing 8).
2. Once the de ation is completed, push the stem in and
turn 90 degree left to return it to the in ation position.
3. Replace the cap back.
For Cover Air Bladder:
1. Pull valve cap out and squeeze the valve at its base
until de ated.
2. Close and recess the valve back.
Spa Control Unit Installation
1. Connect the spa control unit to the spa tub (see drawing 9). Hand-tighten the connectors securely.
Do not use tools to tighten.
CAUTION: Do not sit, lean, cover or place any objects over the spa control unit.
2. Attach the lter cartridge housing assembly to the inside of the spa tub outlet grid (marked “B”) (see
drawing 10).
In ate the spa tub rst before installing lter pump ttings.
3. Before lling with water ensure the bottom drain valve caps are securely closed on the inside and outside.
4. Fill the spa tub with freshwater to a level between MIN and MAX marked on the inside of the spa wall. Do
not over ll the spa. Never move the spa tub with water inside and/or with the control base attached to the
spa as the spa or control base may be damaged.
WARNING: Never pour water with a temperature higher than 40°C (104°F) into the spa
directly. It is recommended to ll the spa tub with lukewarm water for quick heating and
energy saving.
5. Place the spa cover and spa air bladder (pre-installed in spa cover) over the spa tub, and make sure the
spa cover buckles are locked using the key provided after pulling the buckled straps tight.
IMPORTANT: Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never
use a damaged spa cover.
6. Ensure the spa is plugged into an electrical socket and press the button to turn on the control unit
panel buttons rst. Press the button on the control panel to activate the heater, see “Spa Control Unit
Panel” operation section.
IMPORTANT: The following conditions will lead to slow water heating:
The ambient temperature is lower than 50ºF (10ºC).
Outdoor wind speed is above 8-12 mph (3.5-5.4m/s).
The jet function is activated when heating the spa water.
The spa is not properly covered with the spa cover when the water is heating.
8
10
B
B
C
A
A
C
B
9
264
A
S AVE THESE INSTRUCTIONS
(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015
English
Page 18
SPA WATER CHEMISTRY AND BALANCE (continued)
Lowering Total Alkalinity
Amount of Sodium Bisulfate to lower Total Alkalinity
Raising Total Alkalinity
Amount of Sodium Bicarbonate to raise Total Alkalinity
Amount of Muriatic Acid to lower Total Alkalinity
(Muriatic acid: 31.45%)
pH Adjustment
After the total alkalinity has been lowered to 120 ppm or raised to 80ppm and the pH is still high or low, you
can adjust it using the following chart.
Lowering pH
Lowering pH Using Muriatic Acid
Lowering pH Using Sodium Bisulfate
Desired level 60 ppm 80 ppm 100 ppm 120 ppm 140 ppm
Volume:
210 gal / 795 L
0.269 Lb 0.358 Lb 0.448 Lb 0.528 Lb 0.627 Lb
121 g 161 g 202 g 238 g 283 g
Volume:
290 gal / 1098 L
0.368 Lb 0.492 Lb 0.614 Lb 0.737 Lb 0.860 Lb
168 g 224 g 279 g 335 g 391 g
Desired level 60 ppm 80 ppm 100 ppm 120 ppm 140 ppm
Volume:
210 gal / 795 L
0.101 qt 0.135 qt 0.169 qt 0.202 qt 0.234 qt
96 mL 128 mL 160 mL 192 mL 223 mL
Volume:
290 gal / 1098 L
0.139 qt 0.185 qt 0.232 qt 0.278 qt 0.324 qt
132 mL 176 mL 220 mL 264 mL 308 mL
Desired level 20 ppm 40 ppm 60 ppm 80 ppm
Volume:
210 gal / 795 L
0.059 Lb 0.118 Lb 0.178 Lb 0.237 Lb
27 g 53 g 80 g 107 g
Volume:
290 gal / 1098 L
0.081 Lb 0.162 Lb 0.244 Lb 0.326 Lb
37 g 74 g 111 g 148 g
Volume 210 gal (795 L) 290 gal (1098 L)
Total Alkalinity 120 ppm 80 ppm 120 ppm 80 ppm
FromTo
8.47.2 0.028 qt 0.018 qt 0.038 qt 0.025 qt
26 mL 18 mL 36 mL 24 mL
7.87.2 0.019 qt 0.013 qt 0.026 qt 0.017 qt
18 mL 12 mL 22 mL 16 mL
Volume 210 gal (795 L) 290 gal (1098 L)
Total Alkalinity 120 ppm 80 ppm 120 ppm 80 ppm
FromTo
8.47.2 0.071 Lb 0.047 Lb 0.095 Lb 0.063 Lb
32 g 21 g 43 g 29 g
7.87.2 0.047 Lb 0.032 Lb 0.064 Lb 0.043 Lb
21 g 14 g 29 g 20 g
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex PureSpa - SJB-HS-30-1C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex PureSpa - SJB-HS-30-1C in de taal/talen: Engels als bijlage per email.

De handleiding is 2,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Intex PureSpa - SJB-HS-30-1C

Intex PureSpa - SJB-HS-30-1C Gebruiksaanwijzing - Nederlands - 28 pagina's

Intex PureSpa - SJB-HS-30-1C Gebruiksaanwijzing - Deutsch - 29 pagina's

Intex PureSpa - SJB-HS-30-1C Gebruiksaanwijzing - Français - 27 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info