686042
5
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
265
A
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
OWNER’S MANUAL
PureSpa™
SJB-HS-20
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
265-*A*-R0-1508
Do not forget to try these other ne Intex products: pools, pool
accessories, in-home toys, airbeds and boats available at ne
retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves
the right to change speci cations and appearance, which may
result in updates to the instruction manual without notice.
For illustrative purposes only.
©2014 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte
vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/
Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in
Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex
Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne
par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading B.V., Venneveld 9, 4705 RR
Roosendaal – The Netherlands
www.intexcorp.com
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 2
Warning.......................................................................................... 3-5
Parts............................................................................................... 6-7
Product Information & Speci cations........................................ 8
Set-up............................................................................................. 8-11
Salt Level Information.................................................................. 12
Operation....................................................................................... 13-14
LED Code Chart............................................................................. 15
Maintenance and Chemicals........................................................ 16-23
Storage........................................................................................... 23
Troubleshooting............................................................................ 24-26
Warranty......................................................................................... 27
TABLE OF CONTENTS
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 3
IMPORTANT SAFETY RULES
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following.
READ AND FOLLOW ALL INSTRUCTIONS
The spa electrical appliance should be supplied through a residual current device (RCD) having a
rated residual operating current not exceeding 10 mA.
Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding 12V,
must be inaccessible to a person in the spa.
Electrical installation shall ful ll the requirements of local national standards.
Parts incorporating electrical components, except remote control devices, must be located or xed so
that they cannot fall into the spa.
To reduce the risk of injury, do not permit children to use this product unless they are closely
supervised at all times.
Children should not use spas or hot tubs without adult supervision.
To reduce the risk of child drowning, supervise children at all times. Attach and lock spa cover after
each use.
To reduce the risk of injury:
a) The water in a spa should never exceed 40°C (104°F). Water temperatures between 38°C (100°F)
and 40°C (104°F) are considered safe for a healthy adult. Lower water temperatures are
recommended for young children and when spa use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal damage during the early
months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures
to 38°C (100°F).
c) Before entering a spa or hot tub, the user should measure the water temperature with an accurate
thermometer since the tolerance of water temperature-regulating devices varies.
d) The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with
the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory
system problems, or diabetes should consult a physician before using a spa.
f) Persons using medication should consult a physician before using a spa since some medication may
induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.
DANGER
WARNING
Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by
children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at
all times.
Risk of drowning. Inspect the spa cover regularly for leaks, premature wear and tear, damage, or
signs of deterioration. Never use a worn or damaged cover: it will not provide the level of protection
required to prevent unsupervised access to the spa by a child.
Risk of injury. Replace damaged cord immediately. Do not bury cord.
Risk of Electric Shock. Do not permit any electric appliance, such as a light, telephone, radio, or
television, within 3.5 m (11.5 feet) of a spa or hot tub.
Risk of Electric Shock. Do not use and unplug the spa when it is raining, thundering or lightning.
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 4
g) People using medications and/or having an adverse medical history should consult a physician
before using a spa or hot tub.
h) Check with a doctor before use if pregnant, diabetic, in poor health, or under medical care.
People with infectious diseases should not use a spa or hot tub.
To avoid injury exercise care when entering or existing the spa or hot tub.
Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness
and possible drowning.
Pregnant and possible pregnant women should consult a physician before using a spa or hot tub.
Water temperature in excess of 38ºC degree may be injurious to your health.
Do not use a spa or hot tub immediately following strenuous exercise.
Prolonged immersion in a spa or hot tub may be injurious to your health.
When pregnant, soaking in hot water for long periods can harm your fetus. Measure the water
temperature before entering. Do not enter spa if water is hotter than 38°C (100°F). Do not stay in
spa for longer than 10 minutes.
Spa heat in conjunction with alcohol, drugs, or medication can cause unconsciousness.
Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyperthermia and
unconsciousness.
The causes, symptoms, and effects of hyperthermia may be described as follows: Hyperthermia
occurs when the internal temperature of the body reaches a level several degrees above the normal
body temperature of 37°C (98.6°F). The symptoms of hyperthermia include an increase in the
internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of
hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub;
unawareness of impending hazard; fetal damage in pregnant women; physical inability to exit the spa
or hot tub; and unconsciousness resulting in the danger of drowning.
The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs
and spas.
Always add chemicals to water, never add water to chemicals. Adding water to chemicals may cause
strong fumes or violent reactions and hazardous chemical spray.
Never jump or dive into a spa or any shallow body of water.
Assembly and disassembly by adults only.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
No part of the electrical appliance is to be located above the bath during use.
Keep the plug of this product more than 4m away from the spa and at a height of 1.2m at least.
Always unplug this product from the electrical outlet before removing, cleaning, servicing or making
any adjustment to the product.
Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge
trimmers and other equipment.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
quali ed persons in order to avoid a hazard. Use only identical replacement parts when servicing.
WARNING
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
CAUTION
Maintain water chemistry in accordance with manufacturer’s instructions.
1. Press the RESET button on the RCD.
2. Turn on the spa electrical equipment.
3. Press the TEST button on the RCD. The RCD indicator should
turn off and the electrical equipment should shut off. If the RCD
indicator does not turn off, and the electrical equipment does not
shut off, the RCD is faulty. Do not use the spa. Contact a quali ed
electrician to correct the fault.
4. Press the RESET button on the RCD. The indicator on the RCD
should turn on. If the RCD indicator does not turn on, the RCD is
faulty. Do not use the spa. Contact a quali ed electrician
immediately to correct the fault.
WARNING
TEST
RESET
RESET
TEST
TEST
RESET
RESET
TEST
TEST
Page 5
To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter
plugs to connect unit to electrical supply; provide a properly located outlet.
Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
Do not leave the spa empty for extended period of time. Do not expose the spa under direct
sunshine.
Adequate drainage system must be provided around the spa to deal with over ow water.
Do not allow the water in the spa to freeze. Do not turn on the spa when the water is frozen.
Do not use the spa if damaged in delivery and/or malfunctioning in any fashion. Contact the Intex
service center for further direction.
Never use the spa alone or allow others to use the spa alone.
Never pour water with a temperature higher than 40°C (104°F) into the spa directly.
Keep all pets away from spa to avoid any damage.
Do not add bath oil or bath salt to the spa water.
WARNING
This product is provided with a RCD located at the end of the power cord. The RCD must be
tested before each use. Do not use the spa if the RCD does not function properly.
Disconnect the power cord until the fault has been identi ed and corrected. Contact a quali ed
electrician to correct the fault. Do not bypass the RCD. There are no serviceable parts inside
the RCD. Opening the RCD will void the warranty.
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 6
PARTS
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
910
18
17
19
8
21
5
22
1
6
3
4
1213
16
11
14
24
26
25
A
B
C
A
B
C
15
23
30
29
28
20
31 32 33
2
D
D
27
37
36
35
34 7
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
When ordering parts, be sure to quote the model number and part numbers.
PARTS (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
Page 7
REF. NO. DESCRIPTION QTY. PART NO.
1 CONTROL BASE 1 11948
2 SPA FILTER MOTOR 1 11888
3 CONTROL PANEL (INCLUDED #4) 1 11949
4 CONTROL PANEL BOLT 3 11996
5 PRESSURE GAUGE 1 11741
6 CONTROL PANEL BOLT WRENCH 1 11053
7 SPA INFLATION HOSE 1 11830
8 SPA CONTROL INLET/OUTLET O-RING 2 11788
9 SPA CONTROL JET AIR INLET O-RING 1 11699
10 SPA DRAIN PLUG 1 11995
11 SPA DRAIN VALVE ADAPTOR 1 11718
12 FILTER CARTRIDGE HOUSING 1 11798
13 FILTER CARTRIDGE 2 11692
14 FILTER CARTRIDGE HOUSING LID 1 11797
15 INLET PLUG 1 11739
16 SPA TUB 1 11944
17 SPA COVER 1 11950
18
SPA COVER INFLATABLE BLADDER (PRE-INSTALLED IN SPA COVER)
1 11689
19 GROUND CLOTH 1 11717
20 ELECTROLYTIC CELL NUT WRENCH 1 11854
21 TEST STRIPS 1 11855
22 WRENCH 1 11742
23 OUTLET PLUG 2 11782
24 CONTROL PANEL JET AIR HOSE CONNECTION O-RING 1 11711
25 MALE BUCKLE 6 11994
26 FEMALE BUCKLE 6 11993
27 SPA CONTROL AIR INLET O-RING 1 11687
28 ELECTROLYTIC CELL COVER SCREW 4 11712
29 ELECTROLYTIC CELL COVER 1 11890
30 ELECTROLYTIC CELL COVER O-RING 1 11897
31 ELECTROLYTIC CELL NUT 1 11852
32 ELECTROLYTIC CELL 1 11851
33 ELECTROLYTIC CELL O-RING 1 11853
34 DEFLATION OUTLET CAP 1 11992
35 DEFLATION HOSE ADAPTOR 1 11935
36 INFLATION HOSE ADAPTOR 1 11829
37 CONTROL BASE INFLATION CAP 1 11991
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 8
PRODUCT SPECIFICATIONS
SET UP
Maximum seating capacity: 4 adults
Water capacity: 210 gal (795 L)
Inner/outer diameter: 57/77 in (145/196 cm)
Height: 28 in (71 cm)
Jet pump: 0.9HP / 220-240 V / 50 Hz
Bubble air blower: 1.1HP / 220-240 V / 50 Hz
Filter pump ow rate: 460 gal/hr (1,741 L/hr)
Heater power: 2,200 Watts / 220-240 V / 50Hz
Temperature range: 20ºC – 40ºC (68ºF – 104ºF)
Temperature rise: 1.5-2.5ºC/hr (3ºF – 4.5ºF/hr)
Number of Water Jet Nozzles: 4
Number of Bubble Jets: 120
Spa tub recommended working air pressure: 0.083 bar (1.2 psi)
Cord-connected spa with pump, heater, water jet, blower, control panel, built-in hard water treatment, and
sanitation system.
This product requires a minimum of 13 Amps. If the circuit breaker trips, please check that no other
appliances or other large loads are on the same circuit as the spa.
Site preparation and requirements
The spa can be installed indoor or outdoor. For household use only.
The spa must be setup on a level, at and smooth surface that is capable of supporting the maximum load of the lled
spa with four adult occupants; weight 1136Kg (2500 lbs).
Make sure the area is free of sharp objects under or around the spa.
Provide adequate drainage system around the spa to deal with over ow water and splashes.
Provide a properly located power outlet to connect the spa and allow easy access for periodic testing of the cord
mounted RCD.
Make sure there is enough clearance around the spa for full access to the spa equipment for maintenance and/or
service.
The area shall facilitate draining purposes during long term spa storage.
Additional requirements for indoor installation
Make sure the oor can support the full weight of the lled spa with the maximum number of occupants. Check with a
quali ed contractor or a structural engineer to verify this requirement.
Make sure the oor is water resistant and non-slip surface. Do not install the spa on carpet or other materials that will be
damaged by moisture, condensation.
Do not install the spa indoors on a second oor above nished living space due to the possibility of water and humidity
damage.
Humidity is a natural side effect of indoor spa installation. The room shall be properly ventilated to allow moisture to
escape. Install a ventilating system to prevent excess condensation, moisture in the room.
Additional requirements for outdoor installation
Spa owners may need to comply with local or states laws relating to childproof fencing, safety barriers, lighting, and
other safety requirements. Contact your local building code enforcement of ce for further details.
Make sure the surface is level, at, smooth and strong enough to support the full weight of the lled spa.
Do not setup the spa on grass or dirt, as this increases the amount of debris entering the spa, and damage the spa oor.
Do not expose the spa to direct sunlight for extended period of time.
It is possible to install and leave the spa outside at a temperature not lower than 4°C (39°F) provided the water
temperature inside the spa is higher than 4°C (39°F) and the water inside the circulation system, pump, pipe are not
frozen. Put a “temp barrier mat” between the spa oor and the ground to prevent heat loss from the bottom of the spa
and to provide better heat retention.
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
SET UP (continued)
Setup the spa with at least 2 persons.
1. Move the entire package to the selected site. Do not drag the spa tub across the ground as this can
cause damage and leakage.
Open the carton carefully as this carton can be used to store the spa during long term storage or when
not in use.
2. Lay out all the parts on the ground and make sure all the parts are accounted for. For missing or
damaged parts contact the appropriate Intex Service Center listed in the separate “Authorized service
Centers” sheet.
Spa Control Unit Assembly
1. Connect the control panel (3) cable plug into the receptacle on top of the spa control base and screw in
the plug cover rmly by hand (see drawing 1). Note: Spread the ground cloth with the bubbles facing
down over the cleared area where you intend to setup your spa.
2. Screw the control panel bolts (4) with the provided bolt wrench (6) to secure the control panel (see
drawing 2).
3. Plug the spa control unit into an electrical outlet.
Page 9
For indoor in ation:
In ate the Spa Tub Wall
1. Take out the ground cloth (19) and spread it over the cleared area. Then spread out the spa liner over
the ground cloth and point the drain valve towards a suitable draining area.
NOTE: Spread the ground cloth with the bubbles facing down over the cleared area where you intend
to setup your spa.
2. Unscrew the control base in ation cap (37) to reveal the air blower in ation outlet, insert one end of the
in ation hose (7) into the outlet and turn to the right to lock it (see drawing 3).
3. Unscrew the air valve cap to reveal the stem in the up position for in ation. Insert the other end of the
in ation hose (7) into the valve and turn to the right to lock it in position (see drawing 4).
4
6
2
1
12
3
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 10
SET UP (continued)
6. Disconnect the in ation hose (7) from the air valve and attach the pressure gauge (5) to the air valve.
The pressure gauge indicator should be in the green area for a properly in ated spa tub (see drawing 6).
Repeat previous steps to add more air if necessary.
7. Replace the air valve cap back.
NOTE: The cap is designed to be screwed on and off. Never exert force as this could cause the
complete internal in ation system of the valve to come loose. See “Spa Tub Air Valve Fastening” for
valve maintenance.
In ate the Spa Cover Air Bladder
1. Open the in ation valve and insert the in ation
hose
(7) into the valve; press to in ate
until it is rm to the touch but not hard (see
drawing 7).
2. Disconnect the in ation hose (7) from the air
blower in ation outlet and the valve.
3. Replace the control base in ation cap (37) back;
close and recess the in ation valve.
NOTE: If there is a need to add some air to the spa tub wall or spa cover air bladder after they have been
setup, refer to above “In ate the Spa Tub Wall” and “In ate the Spa Cover Air Bladder” sections. The cover
air bladder is preinstalled inside the spa cover. If it needs to be reinstalled, place the unin ated air bladder
inside the spa cover lip before in ating the bladder.
5
4
7
1 2
6
5
1
2
3
37
36
4. Press the button to turn on the control unit panel buttons rst. Press the button to in ate the
spa tub wall until it is rm to the touch but not hard (see drawing 5).
IMPORTANT: Do not over in ate or use high pressure air compressor to in ate.
5. Press the button again to turn it off.
7
7
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 11
SET UP (continued)
De ation
For Spa Tub Wall:
1. Unscrew the cap to reveal the stem, push the stem in
and turn 90 degree right to secure it in the down
position
(see drawing 8).
2. Once the de ation is completed, push the stem in and
turn 90 degree left to return it to the in ation position.
3. Replace the cap back.
For Cover Air Bladder:
1. Pull valve cap out and squeeze the valve at its base
until de ated.
2. Close and recess the valve back.
Spa Control Unit Installation
1. Connect the spa control unit to the spa tub (see drawing 9). Hand-tighten the connectors securely.
Do not use tools to tighten.
CAUTION: Do not sit, lean, cover or place any objects over the spa control unit.
2. Attach the lter cartridge housing assembly to the inside of the spa tub outlet grid (marked “B”) (see
drawing 10).
In ate the spa tub rst before installing lter pump ttings.
3. Before lling with water ensure the bottom drain valve caps are securely closed on the inside and outside.
4. Fill the spa tub with freshwater to a level between MIN and MAX marked on the inside of the spa wall. Do
not over ll the spa. Never move the spa tub with water inside and/or with the control base attached to the
spa as the spa or control base may be damaged.
WARNING: Never pour water with a temperature higher than 40°C (104°F) into the spa
directly. It is recommended to ll the spa tub with lukewarm water for quick heating and
energy saving.
5. Place the spa cover and spa air bladder (pre-installed in spa cover) over the spa tub, and make sure the
spa cover buckles are locked using the key provided after pulling the buckled straps tight.
IMPORTANT: Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never
use a damaged spa cover.
6. Ensure the spa is plugged into an electrical socket and press the button to turn on the control unit
panel buttons rst. Press the button on the control panel to activate the heater, see “Spa Control Unit
Panel” operation section. The heating system is capable of increasing the water temperature by
approximately 1.5-2.5ºC (3-4.5ºF) per hour.
IMPORTANT: The following conditions will lead to slow water heating:
The ambient temperature is lower than 50ºF (10ºC).
Outdoor wind speed is above 8-12 mph (3.5-5.4m/s).
The jet function is activated when heating the spa water.
The spa is not properly covered with the spa cover when the water is heating.
8
10
B
BD
C
A
A
D
C
B
9
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 12
The spa comes with a built-in saltwater sanitation system. Common salt (sodium chloride) is
made up of two elements, sodium and chloride. During the installation of the device, a
measured quantity of salt is dissolved in the SPA water to make it slightly salty. The SPA water
ows through the sanitation system’s electrolytic cell to produce chlorine. The chlorine dissolves
in the water and instantly starts destroying bacteria and algae. It also oxidizes all other organic
materials.
Which kind of salt to use:
Use only Sodium Chloride Salts
Use only sodium chloride (NaCl) salt that is at least 99.9% pure. It is also acceptable to use water
conditioning salt pellets (the compressed forms of evaporated salt). However, it will take a longer
time for them to dissolve. Do not use iodized or yellow (yellow prussiate of soda) colored
salt. Salt is added to the SPA water and the electrolytic cell uses the salt to create chlorine. The
purer the salt the better the performance of the electrolytic cell.
Optimum Salt Levels
The ideal salt level in the SPA water is between 2000-3000 ppm (parts per million). The optimal
level is 2500 ppm.
A too low salt level will reduce the ef ciency of the sanitation system and result in low chlorine
production. Too high a salt level may damage the power supply and cause corrosion to metal
xtures and accessories. The salt in the SPA is constantly recycled. The loss of salt is due only to
SPA water being physically removed from the SPA. Salt is not lost due to evaporation.
• Adding Salt
1. Switch the JET pump on to start the water circulation.
2. Keep the sanitation system turned off.
3. Evenly spread 4.4 lbs / 2 kg of salt around the inside perimeter of the SPA.
4. Brush the SPA bottom to speed up the dissolving process. Do not allow salt to pile up on the
bottom of the SPA. Run the JET pump for one hour to thoroughly dissolve the salt.
5. When all the salt is dissolved, press the sanitizer button to activate the sanitation system
(see “Sanitation System Operating Instructions” section), code “003H” is ashing and set the
sanitation system to desired operating hours. NOTE: DO NOT press any other buttons on the
control panel, ensure the heater is off and attach the spa cover during the sanitizing process.
Removing Salt if Salt Level is too high
If too much salt has been added, the unit will beep and display “E92” (see “LED Code Chart”). If
this happens, turn off the sanitation system by pressing the ON/OFF button , and unplug the
spa. You will need to lower the salt concentration. The only way to do so is to partially drain the
SPA and re ll it with fresh water. Drain and re ll approximately 25% of the SPA water until the “E92”
alarm code disappears.
Adding Salt if Salt Level is too low
If not enough salt has been added, the unit will beep and display “E91” (see “LED Code Chart”).
If this happens, turn off the sanitation system by pressing the ON/OFF button , unplug the
spa and wait 10 seconds. Plug and turn on the spa, add 1.1 lbs / 0.5 kg increment of salt until the
“E91” alarm code disappears (see “Adding Salt” section).
SALT LEVEL INFORMATION
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
Page 13
OPERATION
On/Off Button: Once the unit is plugged in, use this button to active the control unit panel buttons. The
light next to the button is green when activated. Press this button to turn off all currently activated functions.
NOTE: The On/Off button may appear as a black button in the center of the control panel.
Heat Button: Use this button to activate the heating system. The pump will heat the spa water until the
water temperature reaches the set temperature. When the spa water temperature drops 1-2°C (1.8-3.6°F)
below the set temperature the heating system will restart. When the ame icon on the display is red, the
heating system is activated. When the ame icon turns green, the water is at the set temperature. The
heating system is at rest and the ltration system will continue working nonstop.
NOTE: To stop the ltration system while the heater is at rest mode, press the ame button rst and then
the lter button. Pressing the ame button only while the heater is at rest mode will turn off the heating
system only and the ltration system will operate for another 24 hours before it turns off automatically.
Celsius/Fahrenheit Toggle button:
The temperature can be displayed in either Fahrenheit or Celsius. The system’s default is Celsius.
CAUTION: NEVER use the spa if indicated water temperature is more than 40°C (104ºF).
Temperature Adjustment Buttons: Pressing the Temperature Increase or Decrease buttons will
cause the LED to ash. When ashing you can adjust to the desired temperature setting. If you hold these
buttons down the values will rapidly increase or decrease. The new and desired temperature setting will
remain on the LED display for 5 seconds to con rm the new value.
NOTE: The default temperature is 20°C (68°F).
NOTE: Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
Water Filter Button:
This button turns the lter pump on and off.
If the heating system is activated the ltration system will
automatically start.
The water lter icon on the display is green when activated.
Water Jet Button: Use this button to activate the jet massage system. After 30 minutes of continues
use, the jet massage system will automatically turn off. The water jet icon on the displays is green when
activated. The angle of the water jet nozzles inside the spa tub wall can be adjusted manually.
WARNING: Do not run jet system when the cover is attached, air pressure may accumulate inside the spa
and cause irreparable damage and bodily harm.
Bubble Button: Use this button to activate the massage system, which has a 30-minute auto-shutoff
feature. The bubble icon on the displays is green when activated.
WARNING: Do not run Bubble system when the cover is attached, air can accumulate inside the spa and
cause irreparable damage and bodily harm.
Sanitizer Button: Use this button to activate and set operating hours for the sanitation system.
LED Display: Once plugged in the LED displays the current water temperature automatically.
NOTE: The built-in hard water treatment function works automatically in conjunction with the ltration system.
Jet Nozzle Adjustment
The amount of water and pressure coming out from the jet nozzles can be adjusted by turning the jet
nozzle rim clockwise (maximum water output), counterclockwise (low water output) or anything in between.
Closing one or 2 jet nozzles will divert more water pressure to the other jet nozzles.
A: Heat Button
B: Celsius/Fahrenheit Toggle Button
C: Temperature Increase Button
D: Temperature Decrease Button
E: Water Filter Button
F: Water Jet Button
G: Sanitizer button
H: LED Display
I: On/Off Button
J: Bubble Button
SPA CONTROL UNIT PANEL
 )
F
J
D
C
B
A
H
GI
E
-+
40 C
o
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex PureSpa - SJB-HS-20-1C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex PureSpa - SJB-HS-20-1C in de taal/talen: Engels als bijlage per email.

De handleiding is 2,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Intex PureSpa - SJB-HS-20-1C

Intex PureSpa - SJB-HS-20-1C Gebruiksaanwijzing - Nederlands - 28 pagina's

Intex PureSpa - SJB-HS-20-1C Gebruiksaanwijzing - Deutsch - 29 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info