686578
17
Verklein
Vergroot
Pagina terug
1/34
Pagina verder
344
NLA
S AVE THESE INSTRUCTIONS
(344NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2019
English
Page 17
SPA CONTROL PANEL
G: Sanitizer Button
H: Heat Button
I: Heater Start Timer (HST) Button
OPERATION (continued)
Sanitizer Button: Use this button to activate and set operating hours for the sanitation
system.
Heat Button: Press this button to activate the heating system. Press or to set the
desired water temperature. The heater will continuously heat until the water temperature
reaches the set temperature and then hold at that temperature. This is achieved by the heater
restarting automatically whenever the water temperature drops 1-2°C (1.8-3.6°F) below the set
temperature. When the ame icon on the display is red, the heating system is activated. When
the ame icon turns green, the water is at the set temperature. The heating system is then at
rest, but the ltration system will continue circulating water nonstop, unless manually turned off.
If the heating system is reactivated, the lter pump will restart at the same time.
NOTE: To stop the ltration system while the heater is at rest mode, press the ame button
rst and then the lter button. Pressing the heat button only while the heater is at rest mode will
turn off the heating system only and the ltration system will operate for 1 more minute before
it turns off or continue with the lter pump preset operating hours. To turn the heater off while
heating, press the ame button.
IMPORTANT: The following conditions will lead to slow water heating:
The ambient temperature is lower than 50ºF (10ºC).
Outdoor wind speed is above 8-12 mph (3.5-5.4 m/s).
The jet or bubble function is activated when heating the spa water.
The spa is not properly covered with the spa cover when the water is heating.
Heater Start Timer (HST) Button: Use this button to select a future start time for the heating
system. Press this button and then press or to set the number of hours by which you
wish to delay the start of the heating system, from 000 to 120 hours. The icon will ash red for a
few seconds and then stays red. The information shown on the LED display alternates between
the remaining hours before heater start and the water temperature. Once the countdown timer
reaches 000, the heating system will start operating. To deactivate the function at any time,
simply set the HST time back to 000. To readjust the preset hours, press the HST button twice
and adjust the hours with and buttons.
Example 1: It is 9:00pm Monday evening and you would like the spa to be hot on Friday
evening. Allowing for 24 hours for the spa to heat up (4 persons model about 1.5-2.5ºC (3-4.5ºF)
per hour) the heater should be set to start on Thursday evening. With the Spa turned on, rst
press the Heat button and set your desired temperature. Press the HST button and then
or until 072 hours is shown. The heater will start after 72 hours has passed (Thursday at
9:00pm) and will run until the desired temperature is attained. The heater will then cycle on
and off to maintain the set temperature until turned off. To turn off the heater, press the ame
button.
IG
H
17

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Intex-PureSpa---28492-PS-BH-20

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex PureSpa - 28492 PS-BH-20 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex PureSpa - 28492 PS-BH-20 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Intex PureSpa - 28492 PS-BH-20

Intex PureSpa - 28492 PS-BH-20 Gebruiksaanwijzing - Nederlands - 25 pagina's

Intex PureSpa - 28492 PS-BH-20 Gebruiksaanwijzing - Deutsch - 34 pagina's

Intex PureSpa - 28492 PS-BH-20 Gebruiksaanwijzing - Français - 34 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info