686122
9
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
254
PO
S AVE THESE INSTRUCTIONS
(254PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/31/2018
English
Page 9
SET UP
(continued)
5.
Press the button to turn on the control unit panel buttons rst.
Press the button to in ate the spa tub wall for 8 to 10 minutes
until it is rm to the touch but not hard
(see drawing 6)
.
IMPORTANT:
Do not over in ate or use high pressure air
compressor to in ate.
6.
Press the button again to turn it off.
7.
Replace the air valve cap back.
NOTE:
The cap is designed to be screwed on and off. Never exert
force as this could cause the complete internal in ation system of the
valve to come loose. See “Spa Tub Air Valve Fastening” for valve
maintenance.
In ate the Spa Cover Air Bladder
1.
Open the in ation valve and insert the in ation hose
(7)
into the
valve; press to in ate until it is rm to the touch but not hard
(see drawing 7)
.
2.
Disconnect the in ation hose
(7)
from the air blower in ation outlet
and the valve.
3.
Replace the control base in ation cap
(5)
back; close and recess the
in ation valve.
NOTE:
If there is a need to add some air to the spa tub wall or spa cover
air bladder after they have been setup, refer to above “In ate the Spa Tub Wall” and “In ate the Spa Cover
Air Bladder” sections. The cover air bladder is preinstalled inside the spa cover. If it needs to be reinstalled,
place the unin ated air bladder inside the spa cover lip before in ating the bladder.
De ation
For Spa Tub Wall:
1.
Unscrew the cap to reveal the stem, push the stem in and turn 90
degree right to secure it in the down position
(see drawing 8)
.
2.
Once the de ation is completed, push the stem in and turn 90 degree
left to return it to the in ation position.
3.
Replace the cap back.
For Cover Air Bladder:
1.
Pull valve cap out and squeeze the valve at its base until de ated.
2.
Close and recess the valve back.
7
7
6
8
2.
Press the button located on top of the control base
and remove the back cover
(see drawing 3)
.
3.
Unscrew the control base in ation cap
(5)
to reveal the air blower in ation outlet, insert one end of the
in ation hose
(7)
into the outlet and turn to the right to lock it
(see drawing 4)
.
4.
Unscrew the air valve cap to reveal the stem in the up position for in ation. Insert the other end of the
in ation hose
(7)
into the valve and turn to the right to lock it in position
(see drawing 5)
.
3
Press
4
5
7
5
7
1 2
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Intex-Pure-Spa-28403---SSP-H-10-2

Zoeken resetten

  • Pomp maakt een ratelend geluid, zelfs een stukje van de propeller in jaccuzzi gevonden.
    1 vleugeltje afgebroken. Weet er soms iemand waar ik terecht kan voor enkel de propeller? Met dank Gesteld op 2-6-2020 om 19:53

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex Pure Spa 28403 - SSP-H-10-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex Pure Spa 28403 - SSP-H-10-2 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info