686151

Intex ECO7111 Handleiding

29
Verklein
Vergroot
Pagina terug
1/29
Pagina verder
249
PO
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
OWNER’S MANUAL
Cartridge Filter Pump &
Saltwater System with E.C.O.
(Electrocatalytic Oxidation)
Model ECO7111
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance, Visit
www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
Don’t forget to try these other fine Intex products: Pools, Pool
Accessories, Inflatable Pools and In-Home Toys, Airbeds and
Boats available at fine retailers or visit our website listed below.
Due to a policy of continuous product improvement, Intex
reserves the right to change specifications and appearance,
which may result in updates to the instruction manual without
notice.
249-*PO-R0-1705
For illustrative purposes only.
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 2
Warnings
.........................................................................
3
Parts References
............................................................
4-5
Product Information & Specifications
..........................
6
Setup Instructions
..........................................................
7-10
Salt & Pool Water Volumes
............................................
11
Intex Pools Salt Table
.....................................................
12
Intex Pools Cyanuric Acid Table
...................................
13
Intex Pools Operating Time Table
.................................
14
Non-Intex Pools Salt Table
.............................................
15
Non-Intex Pools Cyanuric Acid Table
...........................
15
Non-Intex Pools Operating Time Table
.........................
15
Operating Instructions
...................................................
16-18
LED Code Chart
.............................................................
19
Maintenance
...................................................................
20-22
Long Term Storage
.........................................................
23
Pool Maintenance and Chemical Definitions
..............
24
Troubleshooting Guide
..................................................
25-27
General Aquatic Safety
..................................................
28
Limited Warranty
............................................................
29
TABLE OF CONTENTS
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 3
This product is for use with storable pools only. Do not use with permanently-installed pools. A
storable pool is constructed so that it is capable of being readily disassembled for storage and
reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground
or in a building such that it cannot be readily disassembled for storage.
To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any
electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool.
CAUTION
WARNING
These product warnings, instructions and safety rules provided with the product represent some common risks
of water recreation devices and do not cover all instances of risk and danger. Please use common sense and
good judgement when enjoying any water activity.
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
•
To reduce the risk of injury, do not permit children to use this product. Always supervise children
and those with disabilities.
•
Children must stay away from this product and electrical cord(s).
•
Assembly and disassembly by adults only.
•
Risk of electric shock. Connect only to a grounding type receptacle, this product is provided with
a ground-fault circuit interrupter. If replacement of the plug or cord is needed, use only identical
replacement parts.
•
Always unplug this product from the electrical outlet before removing, cleaning, servicing or
making any adjustment to the product.
•Theunitisprovidedwithaground-faultcircuitinterrupter(GFCI).TotesttheGFCI,pushthetest
button. TheGFCIshouldinterruptpower.Push the reset button, power should be restored. If the
GFCIfailstooperateinthismanner.TheGFCIisdefective.IftheGFCIinterruptspowertothe
pump without the test button being pushed, a ground current is flowing, indicating the possibility
of an electric shock. Do not use this pump. Disconnect the pump and have the problem
corrected by a qualified service representative before using.
•
Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers,
hedge trimmers and other equipment.
•
To reduce the risk of electric shock, replace damaged cord immediately. Use a qualified
electrician to replace the cord.
•
To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or
converter plugs to connect unit to electric supply; provide a properly located outlet.
•
Do not attempt to plug in or unplug this product while standing in water or when your hands are
wet.
•
Donotuseanapplianceleakagecurrentinterrupter(ALCI)inplaceofaGFCIsincetheALCIwill
not protect people.
•Positionthisproductawayfromthepool,soastopreventchildrenfromclimbingonand
accessing the pool.
•
Do not operate this product when the pool is occupied.
•Neverusethepoolifindicatedchlorinelevelismorethan3ppm.
•Thisproductisintendedtobeusedonlyforthepurposesdescribedinthemanual!
•Operatingthisproductwithoutwaterflowingthroughthesystemcancauseabuildupof
flammablegaseswhichcanresultinFIREOREXPLOSION.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY
DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR OTHER SERIOUS
INJURY OR DEATH.
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 4
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents and become familiar
with all the parts.
NOTE:
Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
Notoolsarerequiredfortheassembly.
1
2
3
4
6
5
8
8
7
1
2
10
9
34
13
14
15
12
16
17
30
35
18
11
12
31
33
*
If this pump was not purchased as part of a pool set, the above parts can
be ordered at www.intexcorp.com if needed.
Parts shown on this page are supplied with the pool package and are shown
here for assembly purposes only.
*
19
20
22
23
2421
19
20
21
22
23
36
25
*
37
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 5
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.
" * ": Optional.
When ordering parts, be sure to quote the model number and part numbers.
REF. NO.
DESCRIPTION QTY.
SPARE
PART NO.
SMALL AGP LARGE AGP
COMMON PARTS
1 AIRRELEASEVALVE/SEDIMENTRELEASEVALVE 2 10460
2 VALVEO-RING 2 10264
3 THREADEDFILTERHOUSINGCOLLAR 1 10749
4 FILTERHOUSINGCOVER 1 10750
5 FILTERHOUSINGO-RING 1 10325
6 FILTERCARTRIDGE(29000) 1
7 AIRRELEASEVALVEB(WITHO-RING) 1 10725
8 PUMPHOSEWITHNUTS 2 11009
9
WATERTRANSFERHOSE(WITHCOLLARAND2HOSECLAMPS)
1 11583
10 SCREW 2 11519
11 FLOWSENSOR 1 11460
12 ELECTROLYTICCELLNUT 2 11582
13 ELECTROLYTICCELL(O-RINGCINCLUDED) 1 11906
14 E.C.O
.
ELECTRODE 1 11900
15 L-SHAPEO-RING 1 11228
16 O-RINGC 1 10712
17 ANGLEJOINT(O-RINGDINCLUDED) 1 11584
18 O-RINGA 1 11587
19*
PLUNGERVALVE(HOSEO-RING&STEPWASHERINCLUDED)
2 10747
20* HOSEO-RING 2 10262
21* STEP WASHER 2 10745
22* STRAINERNUT 2 10256
23* FLATSTRAINERRUBBERWASHER 2 10255
24* THREADEDSTRAINERCONNECTOR 1 11235
25* ADJUSTABLEPOOLINLETJETNOZZLE 1 12369
26* ADAPTOR B 2 10722
27* STRAINERCONNECTOR 1 11070
28* POOLINLETJETNOZZLE 1 12364
29* STRAINERGRID 1 11072
30 CELL COVER 1 11131
31 TITANIUMELECTRODE 1 11899
32 TEST STRIPS 1 19635
33
TITANIUMELECTRODEO-RING 2 11585
34
CONTROLSTATION
1
11909
35
COLLARNUT
1
11604
36*
AIRJETVALVE 1 12363
37*
INLETTHREADEDAIRCONNECTOR 1 12371
38*
INLETSTRAINERCONNECTOR 1 12365
39*
POOLINLETAIRADAPTOR 1 12368
40*
AIRJETVALVECAP(NOTSHOWN)
1 12373
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 6
This product is specially designed for above ground pools. It will destroy the bacteria, oxidize
bather organics and control algae, which provide a safe, clean and comfortable swimming pool.
Common salt (sodium chloride) is made up of two elements, sodium and chlorine. During the
installation of your Saltwater System/Filter Pump, a measured quantity of salt is dissolved in the
pool water to make it slightly salty. The pool water flows through the saltwater system’s
electrolytic cell to produce HCLO. The HCLO dissolves in the water and instantly starts
destroying bacteria and algae. It also oxidizes all other organic materials.
The Electrocatalytic Oxidation (E.C.O
.
) is an Advanced Oxidation Processes (AOPs). When
direct current is applied to the electrocatalytic oxidation electrodes, water will be discharged to
generate “hydroxyl radicals”. The hydroxyl radical is a powerful oxidant, which oxidizes organic
contaminants, and destroys bacteria and algae. Hydroxyl radicals in combination with free
available chlorine provide the strongest and safest pool water sanitation.
HOW SANITIZER IS GENERATED
Power: 110 - 120 Volt
Amperage: Saltwater System - 0.6 A; Filter Pump - 1.5 A
IdealSaltLevel: 3000ppm(partspermillion)
Maximum Sanitizer Output/hour: 5 grams/hour
E.C.O
.
Cell Output Current: 500 mA
Limited Warranty: see “Limited Warranty”
HOW THE ELECTROCATALYTIC OXIDATION WORKS
PRODUCT SPECIFICATIONS
Flow Sensor
E.C.O
.
ELECTRODE
Water Outlet
Electronic
Control Station
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 7
STRAINER & PLUNGER VALVE SETUP
Strainer & Plunger Valve Setup (small AGP)
The strainer grid prevents large objects from jamming and/or damaging the filter pump.
The plunger valve assembly prevents water from flowing into the filter pump while the
filter cartridge is being placed or cleaned. If your pool has an inflatable top ring, install the
strainer, nozzle and plunger valve before inflating the pool liner top ring. The parts
numbers here onward, refer to the parts depicted in the Parts List section of this manual.
To install, do the following:
IMPORTANT
The Saltwater System/Filter Pump must be installed as the last piece of pool equipment
in the water return line to the pool. This location extends the life of the titanium plates.
Please visit
www.intexcorp.com
for the latest instructional video on the
installation and operation of this product.
19
20
21
26
(Adaptor B)
38
28
19
20
21
26
(Adaptor B)
27
29
36
39
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 8
The strainer grid prevents large objects from jamming and/or damaging the filter pump. If
your pool has an inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The part numbers here onward refer to the parts depicted in
the Parts List section of this manual. To install, do the following:
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP (OPTIONAL)
1.
In a counter-clockwise motion unscrew plunger valve union
from the threaded strainer connector
(24)
(see drawing 1).
Be careful not to lose the step rubber washer
(21)
. Place the
plunger valve on the ground in a safe place.
2.
In a counter-clockwise motion unscrew the strainer nut
(22)
from the threaded connector
(24).
Leave the flat washer
(23)
on the connector
(24)
.
3.
Install the strainer and plunger valve at the lower position of
pool outlet (marked "+").
From the inside of the pool liner
insert the connector
(24)
into one of the pre-cut holes with
the washer remaining on the connector to be placed against
the inside of the liner wall.
4.
Before assembly, lubricate the threads with a petroleum
jelly. Then, with the flat side of the strainer nut
(22)
facing
the outside wall of the liner in a clockwise motion screw the
strainer nut
(22)
back onto the threaded connector
(24)
(see drawing 2)
.
5.
Finger tighten the strainer nut
(22)
onto the threaded
connector
(24)
.
6.
Grasptheplungervalveassembly.Makesurethestep
washer
(21)
is in place.
7.
In a clockwise motion screw the plunger valve union
back
onto the threaded connector
(24) (see drawing 3)
.
8.
In a clockwise motion turn the plunger valve handle to close
position. Ensure the plunger valve is securely closed.
This will prevent water from flowing out during filling of
the pool
(see drawing 4)
.
2
23
24
INSIDE
LINER WALL
22
1
2
1
3
1
2
4
INSIDE
LINER WALL
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 9
POOL INLET - NOZZLE & PLUNGER VALVE SETUP (OPTIONAL)
5
2
1
7
1
2
8
INSIDE
LINER WALL
9
WATER
FLOW
POOL
6
23
37
25
INSIDE LINER
WALL
22
36
1.
In a counter-clockwise motion unscrew plunger valve
union from the inlet threaded air connector
(37)
(see drawing 5)
Be careful not to lose the step
rubber washer
(21)
. Place the plunger valve on the
ground in a safe place.
2.
In a counter-clockwise motion unscrew the strainer
nut
(22)
from the inlet threaded air connector
(37).
Leave the flat washer
(23)
on the connector
(37)
.
3.
Install the nozzle and plunger valve at the upper
position of pool inlet.
From the inside of the pool
liner insert the nozzle union
(25 & 37)
into one of
the pre-cut holes with the washer remaining on the
connector to be placed against the inside of the liner
wall.
4.
Before assembly, lubricate the threads with a
petroleum jelly. Then, with the flat side of the
strainer nut
(22)
facing the outside wall of the liner
in a clockwise motion screw the strainer nut
(22)
back onto the inlet threaded air connector
(37)
(see drawing 6)
.
5.
Finger tighten the adjustable pool inlet jet nozzle
(25)
and the strainer nut
(22)
onto the inlet threaded air
connector
(37)
.
6.
Grasptheplungervalveassembly.Makesurethe
step washer
(21)
is in place.
7.
Screw the air jet valve
(36)
over the inlet threaded air
connector
(37).
NOTE:
Make sure the air jet valve
is securely tighten and facing up. In a clockwise
motion screw the plunger valve union
back onto the
inlet threaded air connector
(37) (see drawing 7)
.
8.
In a clockwise motion turn the plunger valve handle
to close position. Ensure the plunger valve is
securely closed. This will prevent water from flowing
out during filling of the pool
(see drawing 8)
.
9.
Adjust the direction of the nozzle head pointing
away from the pool outlet for a better circulation
result
(see drawing 9)
.
10.
The pool liner is now ready to be filled with water.
Consult the above-ground-pool owner’s manual for
the filling instructions.
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 10
SALTWATER SYSTEM/FILTER PUMP
Saltwater System/Filter Pump
1.
Remove the Saltwater System/Filter Pump and hoses from the packaging.
2.
Place the Saltwater System/Filter Pump in a location for hose
(8)
connections to the plunger
valve assemblies.
NOTE: Some regional regulations may require the filter pump to be mounted on a
stationary platform. There are two mounting holes located in the pump base for this
reason. Consult your local authorities for filter pump mounting requirements.
3.
Graspthetwopumphoses
(8)
and connect the hose nuts to the Saltwater System/Filter
Pump.
4.
In a counter-clockwise motion unscrew the threaded filter housing collar
(3)
from the filter
housing. Place it in a safe place.
5.
The Saltwater System/Filter Pump is an airtight system. In a counter-clockwise motion turn
both air release valves
(1 & 7)
1 - 2 turns to open.
DO NOT remove air release valves as
water will expel with force if the motor is turned on and injury may occur.
6.
Graspandremovethefilterhousingcover
(4)
. Check to see if a cartridge is inside the
housing. If yes, replace the cover, finger tighten the housing collar
(3)
back onto the filter
housing.
7.
Gentlyfingertightenthesedimentreleasevalvelocatedatthebottomofthehousingtobe
sure that water does not leak out.
8.
When the pool is filled connect the hose from the electrolytic cell outlet to the highest strainer
assembly. You will find the hose connection at the bottom of the plunger valve assembly. Use
the hose nut to attach the hose.
9.
Connect the second hose to the middle of the motor housing and to the remaining liner
connection.
IMPORTANT
To prevent air lock, open the lower plunger valve (connected inlet hose) first and
then the upper plunger valve (connected outlet hose). Open air release valves, lift
and lower the inlet hose until water starts to flow out of the air release valves, close
air release valves.
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 11
SALT & POOL WATER VOLUMES
• Whichkindofsalttouse:
Use only Sodium Chloride Salts
Useonlysodiumchloride(NaCl)saltthatisatleast99.8%pure.Itisalsoacceptabletouse
water conditioning salt pellets (the compressed forms of evaporated salt). However, it will take
a longer time for them to dissolve.
Do not use iodized or yellow (yellow prussiate of soda)
colored salt.
Salt is added to the pool water and the electrolytic cell uses this salt to create the
sanitizer. The purer the salt the better the performance of the electrolytic cell.
• OptimumSaltLevels
Theidealsaltlevelinthepoolwaterisbetween2500-3500ppm(partspermillion).Theoptimal
levelis3000ppm.
A too low salt level will reduce the efficiency of the saltwater system and result in low sanitizer
production. A high salt level may generate a salty taste to the pool water (this may occur at a salt
levelabove3500-4000ppm).Toohighofasaltlevelmaydamagethepowersupplyandcause
corrosion to pool metal fixtures and accessories. The Salt Table page of this manual, shows the
correct dosage of salt needed. The salt in the pool is constantly recycled. Salt loss occurs only
when pool water is physically removed from the pool. Salt is not lost due to evaporation.
• AddingSalt
1.
Switch on the unit, then press and hold both and button for 5 seconds, the LED
flashes “FP”. The unit is now in a Filter pump working mode and switch the filter pump on to
start the water circulation.
2.
Keep the saltwater system turned off.
3.
Determine the amount of salt to be added (see “Salt Table”).
4.
Evenly spread the proper amount of salt around the inside perimeter of the pool.
5.
Avoid clogging the filter by not adding salt through the skimmer.
6.
Brush the pool bottom to speed up the dissolving process. Do not allow salt to pile up on the
bottom of the pool. Run the filter pump 24 consecutive hours to thoroughly dissolve the salt.
7.
After 24 hours and if all the salt is dissolved, turn on the Saltwater System, press button
until you hear a “beep”, code “00” flashing (see “System Operation” section steps 2 to 4) and
set the saltwater system to desired operating time (see “Operating Time Table”).
• RemovingSalt
If too much salt has been added, the unit will beep and display “code 92” (see “Alarm Codes”).
You will need to lower the salt concentration. The only way to do so, is to partially drain the pool
andrefillitwithfreshwater.Drainandrefillapproximately20%ofthepool’swateruntilthe“Code
92” disappears.
• PoolVolumeCalculation
Rectangular
Length x Width x Average Depth x 7.5 Length x Width x Average Depth
Circular
Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79
Oval
Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80
Types of Pool
Gallons
(pool size in feet)
Cubic Meters
(pool size in meters)
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 12
INTEX POOLS SALT TABLE
This table shows the amount of salt needed to achieve and maintain the optimal 3000 ppm
salt level.
Pool Size
Water Capacity
(Calculated at 90% for
Frame Pool and 80% for
Easy Set & Oval Pool)
Salt Needed for
Startup
3.0g/L (3000ppm)
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals)
(Liters) (Lbs) (Kgs) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET
®
POOL
457cmx84cm(15'x33") 2587 9792 65 30 20 10
457cmx91cm(15'x36") 2822 10681 65 30 20 10
457cmx107cm(15'x42") 3284 12430 80 35 20 10
457cmx122cm(15'x48") 3736 14141 95 45 25 10
488cmx107cm(16'x42") 3754 14209 95 45 25 10
488cmx122cm(16'x48") 4273 16173 110 50 30 15
488cmx132cm(16'x52") 4614 17464 115 50 30 15
549cmx107cm(18'x42") 4786 18115 120 55 30 15
549cmx122cm(18'x48") 5455 20647 135 60 35 15
CIRCULAR
METAL
FRAME POOL
457cmx91cm(15'x36") 3282 12422 80 35 20 10
457cmx107cm(15'x42") 3861 14614 100 45 25 10
457cmx122cm(15'x48") 4440 16805 110 50 30 15
488cmx122cm(16'x48") 5061 19156 125 55 35 15
549cmx122cm(18'x48") 6423 24311 160 75 40 20
ULTRA FRAME
®
POOL
488cmx122cm(16'x48") 5061 19156 125 55 35 15
549cmx122cm(18'x48") 6423 24311 160 75 40 20
GRAPHITE GRAY
PANEL POOL
SET™
478cmx124cm(15'8"x49") 4440 16805 110 50 30 15
508cmx124cm(16'8"x49") 5061 19156 125 55 35 15
OVAL FRAME
POOL
305cmx549cmx107cm(10'x18'x42")
2885 10920 70 30 20 10
366cmx610cmx122cm(12'x20'x48")
4393 16628 110 50 30 15
RECT. ULTRA
FRAME POOL
274cmx457cmx122cm(9'x15'x48")
3484 13187 90 40 25 10
274cmx549cmx132cm(9'x18'x52")
4545 17203 115 50 30 15
305cmx610cmx132cm(10'x20'x52")
5835 22085 145 65 40 20
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 13
INTEX POOLS CYANURIC ACID TABLE
Cyanuric acid is a chemical that reduces the loss of chlorine in water due to ultraviolet rays.
To maintain the pool water clear and clean, and to maximize the performance of the device,
add cyanuric acid to the pool. We recommend that the cyanuric acid level be
maintained at approximately 1% of the salt, i.e. 100 Lbs (45 Kgs) salt x1% = 1 Lbs (0.45 Kgs)
cyanuric acid.
If the pool water is dirty, filthy or grimy, DO NOT add chlorine stabilizer (cyanuric acid) as
this will slowdown the sanitation time of the device. Under this condition you must BOOST
your pool water, refer to BOOST cycle steps. Once the pool water has been restored to clear
and clean conditions you may add cyanuric acid.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Cyanuric Acid Needed for
Startup
0.03g/L (30ppm)
(Gals)
(Liters) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET
®
POOL
457cmx84cm(15'x33") 2587 9792 0.6 0.3
457cmx91cm(15'x36") 2822 10681 0.7 0.3
457cmx107cm(15'x42") 3284 12430 0.8 0.4
457cmx122cm(15'x48") 3736 14141 0.9 0.4
488cmx107cm(16'x42") 3754 14209 0.9 0.4
488cmx122cm(16'x48") 4273 16173 1.1 0.5
488cmx132cm(16'x52") 4614 17464 1.2 0.5
549cmx107cm(18'x42") 4786 18115 1.2 0.5
549cmx122cm(18'x48") 5455 20647 1.4 0.6
CIRCULAR
METAL
FRAME POOL
457cmx91cm(15'x36") 3282 12422 0.8 0.4
457cmx107cm(15'x42") 3861 14614 1.0 0.4
457cmx122cm(15'x48") 4440 16805 1.1 0.5
488cmx122cm(16'x48") 5061 19156 1.3 0.6
549cmx122cm(18'x48") 6423 24311 1.6 0.7
ULTRA FRAME
®
POOL
488cmx122cm(16'x48") 5061 19156 1.3 0.6
549cmx122cm(18'x48") 6423 24311 1.6 0.7
GRAPHITE GRAY
PANEL POOL
SET™
478cmx124cm(15'8"x49") 4440 16805 1.1 0.5
508cmx124cm(16'8"x49") 5061 19156 1.3 0.6
OVAL FRAME
POOL
305cmx549cmx107cm(10'x18'x42")
2885 10920 0.7 0.3
366cmx610cmx122cm(12'x20'x48")
4393 16628 1.1 0.5
RECT. ULTRA
FRAME POOL
274cmx457cmx122cm(9'x15'x48")
3484 13187 0.9 0.4
274cmx549cmx132cm(9'x18'x52")
4545 17203 1.1 0.5
305cmx610cmx132cm(10'x20'x52")
5835 22085 1.5 0.7
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 14
INTEX POOLS OPERATING TIME TABLE (WITH CYANURIC ACID)
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Operating Time (hours)
at different ambient/air
temperatures
(Gals) (Liters)
10 - 19°C
(50 - 66°F)
20 - 28°C
(68 - 82°F)
29 - 36°C
(84 - 97°F)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET
®
POOL
457cmx84cm(15'x33")
2587 9792
3 3 4
457cmx91cm(15'x36")
2822 10681
3 4 5
457cmx107cm(15'x42")
3284 12430
3 4 5
457cmx122cm(15'x48")
3736 14141
4 5 6
488cmx107cm(16'x42")
3754 14209
4 5 6
488cmx122cm(16'x48")
4273 16173
4 5 6
488cmx132cm(16'x52")
4614 17464
5 6 7
549cmx107cm(18'x42")
4786 18115
5 6 7
549cmx122cm(18'x48")
5455 20647
6 7 8
CIRCULAR
METAL
FRAME POOL
457cmx91cm(15'x36")
3282 12422
3 4 5
457cmx107cm(15'x42")
3861 14614
4 5 6
457cmx122cm(15'x48")
4440 16805
5 6 6
488cmx122cm(16'x48")
5061 19156
5 6 7
549cmx122cm(18'x48")
6423 24311
7 8 9
ULTRA FRAME
®
POOL
488cmx122cm(16'x48")
5061 19156
5 6 7
549cmx122cm(18'x48")
6423 24311
7 8 9
GRAPHITE GRAY
PANEL POOL
SET™
478cmx124cm(15'8"x49")
4440 16805
5 6 6
508cmx124cm(16'8"x49")
5061 19156
5 6 7
OVAL FRAME
POOL
305cmx549cmx107cm(10'x18'x42")
2885 10920
3 4 5
366cmx610cmx122cm(12'x20'x48")
4393 16628
5 5 6
RECT. ULTRA
FRAME POOL
274cmx457cmx122cm(9'x15'x48")
3484 13187
3 4 5
274cmx549cmx132cm(9'x18'x52")
4545 17203
5 6 7
305cmx610cmx132cm(10'x20'x52")
5835 22085
6 7 8
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 15
SALT TABLE FOR COMMON NON-INTEX POOLS
OPERATING TIME TABLE FOR COMMON NON-INTEX POOLS (WITH CYANURIC ACID)
SALT CALCULATION FORMULA FOR ALL POOLS
Salt Needed for Startup
(Lbs)
Salt Needed for Startup
(Kgs)
Salt Needed when
Low Salt Detected (Lbs)
Salt Needed when
Low Salt Detected (Kgs)
WaterCapacity(Gals)x0.025
WaterCapacity(Liters)x0.003
WaterCapacity(Gals)x0.0067 Water Capacity (Liters) x 0.0008
CYANURIC ACID TABLE FOR COMMON NON-INTEX POOLS
Water Capacity
Salt Needed for Startup
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
2000 7500 50 20 10 5
4000 15000 100 45 25 10
6000 22500 150 65 40 20
7000 26500 175 80 55 20
Water Capacity
Operating Time (hours)
at different ambient/air temperatures
(Gals) (Liters)
10 - 19°C
(50 - 66°F)
20 - 28°C
(68 - 82°F)
29 - 36°C
(84 - 97°F)
2000 7500 2
3 4
4000 15000 4 5 6
6000 22500
6
7 8
7000 26500 7 8 9
Water Capacity
Cyanuric Acid Needed for Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
2000 7500 0.50 0.23
4000 15000 1.00 0.45
6000 22500 1.50 0.68
7000 26500 1.75 0.80
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 16
FILTER PUMP OPERATION
1.
Make sure the unit is switched off. The switch is located on the control station.
2.
ConnectthepowercordtoaGFCIprotectedelectricaloutlet.
3.
Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valve,
allowing water to flow into the filter pump.
4.
With water flowing into unit, the water pressure will allow the air trapped inside to escape
from the air release valves
(1 & 7)
. When all the air has escaped water will flow out of the
valves
(1 & 7)
. When this occurs gently finger tighten the valves in a clockwise direction.
5.
Turn on the switch. The filter pump is now filtering the water.
6.
The green "Pump" light on the control panel will light up, that indicates the filter pump is
running.
To prevent air lock, open the lower plunger valve (connected inlet hose) first and then
the upper plunger valve (connected outlet hose). Open air release valves, lift and lower
the inlet hose until water starts to flow out of the air release valves, close air release
valves.
IMPORTANT
WARNING
Risk of electric shock. Connect this product only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI). Contact a qualified electrician if
you cannot verify that the receptacle is protected by a GFCI.
7
1
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 17
SALTWATER SYSTEM OPERATION
1
.
Start up the unit:
PlugthepowercordintotheelectricaloutletandtesttheGFCI/RCD
(circuitbreaker).Switchontheunit.WiththeFilterPumpturned“ON”
and operating. The green "Pump" light on the control panel will be on
and flashing code “00” appears on the electronic control station’s
LED, indicating that the unit is ready to be programmed. This is
normal.
2.
Set operating hours for Saltwater System:
With code “00” flashing, press button to set the
desired operating hours. See the “Operating Time Table”
for the required operating hours related to each pool
size. Pressing will increase the time from 01 to 12
hours maximum. If you have selected too many hours
keep pressing to repeat the cycle. The built-in timer
will now activate your Saltwater System, at the same
time each day, for the number of hours you have set.
NOTE:
The Saltwater System will not operate if the filter
pump is not operating.
3.
Lock keypad controls:
With the desired hour value showing, press button until you hear a
“beep”.Thegreen“WORKING”indicatoronthecontrolpanelwilllight
up within a few seconds to indicate that the saltwater system has started
sanitizer production.
Locking the control buttons into this setting pre
vents unauthorized changing of the operating cycle.
NOTE:
If you forget to lock the keypad controls, the system will
automatically lock it and start working 1 minute later.
4.
Unlock & Readjust operating time if necessary:
The operating hours can be re-adjusted if necessary. Press button
until you hear a “beep” to unlock the keypad and the current
programmedtimewillflash.Repeatsteps2to3.
(1 to 12 hours max per cycle)
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 18
SALTWATER SYSTEM OPERATION (continued)
5.
Boost cycle
•
First time installation, press and hold “BOOST” button for 5 seconds until the
indicator lights up and the LED display “80”. This indicates that the saltwater
system has started E.C.O
.
and more chlorine sanitizer production. You can
press and hold the “BOOST” button for another 5 seconds until the indicator
is off, which will cancel the Boost cycle.
•
The boost operating hours is 8 times the amount of time programmed into the
system, i.e. if your saltwater system operating time is 2 hours, the boost
procedure will run 8 x 2 = 16 hours. After boost procedure has been completed, the system will
automatically switch to the normal working mode.
•
After a heavy rain or if the pool is dirty, press the “BOOST” button to shock the pool again.
6. Stand-by/power saving mode:
•
When the cycle ends, the green “SLEEP” indicator on the control panel lights
upandtheLEDdisplayflashes“93”.ThesystemisnowinStand-Bymode.
After a while, it shuts down and sets itself in a Power Saving mode. The
system will automatically turn itself back on in 24 hours, starting its daily
cycle of chlorine production.
•
The “SLEEP” indicator stays on, while the system is in the Power Saving
mode. The LED display however, goes blank after 5 minutes. Press any
button ( or ) to view the last LED code.
7. Running the pump alone without the Saltwater System:
To run the pump alone without the Saltwater System function, press and hold
both and buttons until you hear a “beep”, the LED display will show
“FP”.Thepumpisnowoperatingalone.NOTE:Thepumpcannotbe
operated alone under an automatic timer mode. To stop the pump, manually
turn the switch OFF.
To bring back the initial automatic operating cycle setting
of the Saltwater System:
a) If the LED display shows “FP”, press the button and the operating
hours set previously will begin flashing, press the button again or
simply wait 1 minute, and the LED will stay illuminated. The Saltwater
System cycle repeats again.
b)IftheunitisOFF,turntheswitchON,theLEDdisplayshows“FP”,
press the button and the operating hours set previously will begin
flashing, press the button again or simply wait 1 minute, and the
LED will stay illuminated. The Saltwater System cycle repeats again.
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 19
LED CODE CHART
LED Reading Definitions
FP Filter Pump Working Mode
80 Boost Mode
00 Stand-By Mode (Start-up)
01 Minimum Operating Hour (1 hour remaining)
02 Operating Hours (2 hours remaining)
03 OperatingHours(3hoursremaining)
04 Operating Hours (4 hours remaining)
05 Operating Hours (5 hours remaining)
06 Operating Hours (6 hours remaining)
07 Operating Hours (7 hours remaining)
08 Operating Hours (8 hours remaining)
09 Operating Hours (9 hours remaining)
10 Operating Hours (10 hours remaining)
11 Operating Hours (11 hours remaining)
12 Maximum Operating Hours (12 hours remaining)
90 AlarmCode(LowPumpFlow/NoPumpFlow)
91 Alarm Code (Low Salt Level)
92 Alarm Code (High Salt Level)
93 Stand-ByMode(OperatingProcessfinished)
“BLANK” NoPoweror“PowerSavingMode”waitingtostartnext
Saltwater System cycle.
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 20
FLOW SENSOR CLEANING
TITANIUM AND E.C.O
.
ELECTRODES CLEANING
IMPORTANT
Close plunger valves on your pool or insert black hat-like plugs in strainer opening to
prevent water spillage. Open plunger valves or remove plugs when maintenance is
completed.
WARNING
Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
1.
In a counter-clockwise motion unscrew the collar of the flow sensor
(11)
and remove it from
the electrolytic cell conduit
.
See “Part Reference”.
2.
If deposits and debris are seen on the surface of the flow sensor, then use a garden hose to
wash it off.
3.
If flushing with water does not remove the deposits, use a plastic brush to clean the surface
and the hinge if necessary. Do not use a metal brush.
4.
After the flow sensor has been inspected and cleaned, align the locator notch on the flow
sensortotheconnectionridgeintheconduit.Nowturnthecollarinaclockwisemotion,
tightening the sensor back into its position. Do not over tighten.
Connection Ridge
LocatorNotch
Hinge
The titanium electrode and E.C.O
.
electrodes have
a self cleaning function incorporated into the
electronic control’s programming. In most cases this self cleaning action will keep the electrodes
working at optimum efficiency. If the pool water is hard (high mineral content) the electrodes may
require periodic manual cleaning. To maintain maximum performance, we recommend that you
open and visually inspect the titanium and E.C.O
.
electrodes
(4 & 5)
monthly.
The following steps provide instructions on how to clean your cell.
MAINTENANCE
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 21
MAINTENANCE (continued)
1
. Switch off the unit, unplug the power cord from the electrical socket.
2
. Turn both plunger valve handles fully clockwise until they stop. This closes the valve,
prevents the water from flowing out of the pool.
3
. Disconnect the hose with nut
(8)
from the Saltwater System, and assemble the cell cover
(30)
at the side of the cell.
4.
Unscrew the collar of the E.C.O
.
electrode
(14)
and pull out the E.C.O
.
electrode from the
electrolytic cell
(13)
housing.
5.
Pour kitchen grade vinegar into the electrolytic cell
(13)
to immerse the titanium and E.C.O
.
electrodes. Soak for 1 hour.
6.
Open one side of the cell cover
(30)
, drain and properly dispose of the vinegar. Connect the
hose which goes from the pool to the cell. Flush the electrolytic cell housing with the pool
water.
7.
Reversesteps3,4,5and6toreconnecttheelectrolyticcell.
30
8
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 22
It is recommended that the filter cartridge be replaced at least every 2 weeks.
1
. Make sure the unit is turned off, and disconnect the power cord from the electrical outlet.
2
. Turn both plunger valve handles fully clockwise until they stop. This closes the valve,
prevents the water from flowing out of the pool.
3
. Gentlyturnbothairreleasevalves
(1 & 7)
once or twice in a counter-clockwise direction. The
housing cover can now be easily removed.
4
. In a counter-clockwise direction remove the filter housing collar
(3)
. Place it in a safe location.
5
. Remove the housing cover
(4)
.
6
. Nowremovetheusedfiltercartridge.
7
. Examine the inside of the filter housing.
8
. If dirt or sediment is located on the bottom of the housing then:
A
. In a counter-clockwise motion gently unscrew and remove the sediment valve
(1)
located
at the bottom of the housing. Place it in a safe place.
B
. With a bucket of water or a garden hose pour water into the housing flushing out the
sediment.
C
. Screw back the sediment valve
(1)
in a gentle clockwise motion. Do not over-tighten.
9
. Place a new cartridge filter in the housing.
10.
Return the housing cover
(4)
to its installed position and in a clockwise direction rescrew the
housing collar
(3)
onto the filter housing.
11.
Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valve,
allowing water to flow into the filter pump.
12.
Reconnect the power cord.
13.
Turn on the unit.
14.
When the trapped air has escaped through the air release valves gently retighten the
valves
(1 & 7)
in a clockwise direction.
CLEANING OR REPLACING FILTER CARTRIDGES
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 23
MAINTENANCE (continued)
The Test Strips can test the “Free Chlorine”, “pH”, “Calcium Hardness” and “Total Alkalinity”
levels at the same time. We recommend that you test the water chemistry weekly, and maintain
thechlorineconcentrationat0.5-3ppm.
Directions and Use
1
. Dip the entire strip into the water and remove immediately.
2
. Hold the strip level for 15 seconds. Do not shake excess water from the strip.
3
. Nowcomparethestrippadtothecolorchartonthepackaginglabel.Ifnecessary,adjustthe
chemical level in the pool water. It is very important, to use the proper technique when testing
the water's chemical level. Read and follow the written strip instructions carefully.
1
. Disconnect the power cord from the electrical outlet.
2
. After the pool is completely empty, disconnect the Saltwater System from the hoses by
reversing the installation instructions.
3
. Air-dry the unit before you store it. This might be a good time to visually inspect and clean the
electrolytic cell.
4
. Store the unit and accessories in a dry place. The temperature should be controlled, between
32degreesFahrenheit(0degreesCelsius)and97degreesFahrenheit(36degreesCelsius).
5
. The original package can be used for storage.
INTEX
®
TEST STRIPS (PACKED WITH THE PRODUCT)
LONG TERM STORAGE
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 24
POOL MAINTENANCE & CHEMICAL DEFINITIONS
• Donotaddpoolchemicalsdirectlytotheskimmer.Thismaydamagethecell.
•Maintainingahighsaltandsanitizerlevelsaboverecommendedrangecancontributeto
corrosion of pool equipment.
• Checktheexpirydateofthetestkitasthetestresultsmaybeinaccurateifthekitisusedafter
that date.
• If,duetoheavypoolusage,itisrequiredtoincreasethesanitizerlevel,thenuseachemical
based on Trichloro-s-triazinetrione or sodium dichloro-s-triazinetrione dihydrate.
HCLO - A very effective killer of algae and bacteria known as hypochlorous acid.
Free
Chlorine
-
Is the sanitizer (HCLO) present in pool water.
Combined
Chlorine
-
Is formed by the reaction of free Chlorine with ammonia wastes.
Result if too high - Sharp chlorinous odor, eye irritation.
pH
-
A value that indicates how acidic or basic a solution is.
Resultiftoolow- Corrodedmetals,eye&skinirritation,destructionof
total alkalinity.
Result if too high - Scale formation, cloudy water, shorter filter runs, eye
&skinirritation,poorChlorineefficiency.
Total Alkalinity
-
Indicates the degree of the water's resistance to change in pH. It
determines the speed and ease of pH change, so always adjust total alka
linity before adjusting the pH level.
Resultiftoolow- Corrodedmetals,eye&skinirritation.Lowalkalinity
will cause the pH to be unstable. Any chemical added
to the water will have an affect on pH.
Resultiftoohigh- Scaleformation,cloudywater,eye&skinirritation,
poor Chlorine efficiency.
Calcium Hardness
-
Refers to the amount of calcium and magnesium dissolved in the water.
Resultiftoohigh- Eye&skinirritation,difficultybalancingwaterand
poor chlorine efficiency. Scale will form and will
cause the water to become cloudy.
Stabilizer
-
Stabilizers extend the life of Chlorine in swimming pools.
(Cyanuric Acid)
Preferred Water Chemistry Reading
Minimum Ideal Maximum
Free Chlorine
00.5-3.0ppm5.0ppm
Combined Chlorine
0 0 ppm 0.2 ppm
pH
7.2 7.4 - 7.6 7.8
Total Alkalinity
40 ppm 80 ppm 120 ppm
Calcium Hardness
50ppm100-250ppm350ppm
Stabilizer (Cyanuric Acid)
10 ppm 20 - 40 ppm 50 ppm
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 25
TROUBLESHOOTING GUIDE
• Themotorisnotpluggedin.
• Switchisnotturnon.
• TheGFCIcircuitbreakeristripped.
• Motortoohotandoverload
protection is shut off.
• ImpropersanitizerorpHlevels.
• Filtercartridgeisdirty.
• Damagedcartridge.
• Excessivelydirtypool.
• Thestrainerscreenisrestrictingthe
water flow.
• Cloggedinletordischarge.
• Anairleakontheintakeline.
• Scaleorbuilduponcartridge.
• Excessivelydirtypool.
• Dirtyfiltercartridge.
• Inletthreadedairconnector
connected to the wrong hole on
the liner.
• Lowwaterlevel.
• Strainerscreenpluggedup.
• Anairleakontheintakehose.
• Anairlockinsidethecartridge
chamber and motor chamber.
• Servicelighton.
• O-ringmissing.
• Coverisnottight.
• Filtercartridgeisdirty.
•Hosenutsarenotwell-fitted.
• There’sairtrappedinthepump
housing and inlet hose.
• Theinletandoutlethoses
connection are reversed.
• Plungervalvenotwell-fitted.
• Airjetvalveisnottightand
facing up.
• Airjetvalveinternalsealblocked.
• Airjetvalveinternalsealdirty.
• Airjetvalvebroken.
PROBLEM CAUSE SOLUTION
FILTER MOTOR
FAILS TO START
FILTERDOESN’T
CLEANPOOL
FILTERDOESN'T
PUMP WATER OR
FLOW IS VERY
SLOW
PUMPDOESN'T
WORK
TOP COVER
LEAKING
HOSELEAKING
AIR LOCK
INLETTREADED
AIRCONNECTOR
/AIRJETVALVE
LEAKING
• Filtercordmustbepluggedintoa3wireoutlet
thatisprotectedbyaClassAGroundFault
Circuit Interrupter, or RCD.
• Resetcircuitbreaker.Ifcircuitbreakertrips
repeatedly, your electrical system may have a
defect. Turn off circuit breaker and call an
electrician to correct the problem.
• Letmotorcooldown.
•
Adjust the sanitizer and pH level. Consult your
local swimming pool supply stores.
• Cleanorreplacecartridge.
• Checkthecartridgeforholes.Replaceif
damaged.
• Operatethefilterforlongerperiods.
• Cleanthestrainerscreenattheinlet.
• Clearanyobstructionsintheintakehoseby
discharging it inside pool wall.
• Tightenhosenuts,checkhosesfordamage,
check pool water level.
• Replacecartridge.
• Cleancartridgemoreoften.
• Cleaninsidetheplungervalve.
• Pullvalvehandletofulluprightposition.
• Makesuretheinletthreadedairconnectoris
connected to the pool inlet upper hole.
• Fillpooltocorrectwaterlevel.
• Cleanstrainerscreensatpoolinlet.
• Tightenhosenuts,checkhosefordamage.
• Clearanysticksorleavesintheintakehose.
• Turnandpullvalvehandletofullupright
position.
• Unscrewtwoairreleasevalveonthechamber
to fullfill water.
• ContactIntexServiceCenter.
• Removecover&checkforO-ring.
• Tightencover(Manually).
• Replaceorcleancartridge.
•Tightenorreinstallhosenut.
• Openairreleasevalves,liftandlowertheinlet
hose until water starts to flow
out of the valve, then close it.
• Thelowerpositionofpooloutletconnectsto
filter pump water inlet. The upper position of
pool inlet connects to filter pump water outlet.
• Tightenorreinstallplungervalve.
• Tightenairjetvalveandmakesureit’s
facing up.
• TurnpumpONandrunforfewseconds,then
turnOFF,repeat3times.
• Removeairjetvalve,flushdirtoutwithwater
and replace valve back.
• Replaceanewairjetvalve.
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 26
TROUBLESHOOTING GUIDE (continued)
INSUFFICIENT
CHLORINE
WHITEFLAKESIN
THE WATER
NOLEDDISPLAY
•
Insufficient operating hours of the
Saltwater System.
•
The salt level in the pool water is less
than 2000ppm. This is insufficient.
•
Chlorine loss due to intense sunlight
exposure.
•
The bather load has increased.
•
Clogged or dirty electrolytic cell.
•
High UV level exposure.
•
Excessive calcium hardness is
present in pool water.
•
Nopowersupply.
• RCD/GFCIhasnotreseted.
•
A power fuse has blown.
•
LED failure.
•
Increase the daily Saltwater System operating
time. See “Operating Instructions”.
•
Check the salt level with the Test Kit. Adjust
asneeded.See“Salt&PoolWaterVolumes”.
•
Use a pool cover when the pool is not in use
and/or when the unit is operating.
•
Increase the daily Saltwater System operating
time. See “Operating Instructions”.
•
Remove the cell for inspection, clean it if
necessary. See “Maintenance”.
•
Cover the pool with a pool cover for 2 days
with the device running and then test the
water using the test strips.
•
If the pool is clean and clear, add stabilizer
to the water and then test the water with the
device running.
•
Drainabout20to25%ofthepoolwaterand
add fresh water to decrease the calcium
hardness. Inspect the electrolytic cell for scale
buildup. Clean the electrolytic cell if necessary.
•
Plug the cell cord firmly into the cell housing
receptacle.
•
ResettheRCD/GFCI.
•
Contact Intex Service Center.
•
Contact Intex Service Center.
PROBLEM CAUSE SOLUTION
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 27
TROUBLESHOOTING GUIDE (continued)
1
. Circulation line is blocked.
2
. Incorrect inlet and outlet hose direction.
3
. Scale on the flow sensor.
4
. Flow sensor cord is loose.
5
. Inner timer confliction between filter
pump and saltwater system.
6
. Flow sensor failure.
1
. Dirt or scale on titanium plates.
2
.Lowsaltlevel/Nosalt.
3
. Electrolytic cell cord is loose.
4
. Possible electrolytic cell failure.
1
. High salt level.
1
. Display and all lights are off - the
system does not power up.
•
If your unit has plunger valves, ensure that
they are open.
•
Clear your filter cartridge and cell from debris
and dirt. See “Maintenance”.
•
Release all trapped air in the circulation line.
See the filter pump manual.
•
Check the direction of the inlet and the outlet
hose. Reverse the hoses if necessary. See
“Set Up Instructions”.
•
Clean the flow sensor, paying special attention
to the hinge. See “Maintenance”.
•
Plug the flow sensor firmly into the flow sensor
receptacle.
•
Reset both timers on the filter pump and
saltwater system.See “Boost Cycle”.
•
Contact Intex Service Center.
•
Remove the electrolytic cell for inspection.
Clean it if necessary. See “Maintenance”.
•
Addsalt.See“Salt&PoolWater
Volumes”.
•
Ensure that the cell cord is plugged firmly into
the cell housing receptacle.
•
Contact Intex Service Center. Replace the cell
if needed.
•
Partially drain the pool and refill it with fresh
water.See“Salt&PoolWaterVolumes”.
•
Household voltage is too high or too low
(+20%).Checkthevoltageiswithintherange
stated on the device housing.
•
Contact Intex Service Center.
LED PANEL
CODE
PROBLEM
SOLUTION
LEDPanelCodeFlash&AlarmOn(
NOTE
: Always turn off the power before cleaning and servicing).
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service Department for
assistance. See separate “Authorized Service Centers” sheet.
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 28
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves inherent risks
of injury and death. To reduce your risk of injury, read and follow all product,
package and package insert warnings and instructions. Remember, however, that
product warnings, instructions and safety guidelines cover some common risks
of water recreation, but do not cover all risks and dangers.
For additional safeguards, also familiarize yourself with the following general
guidelines as well as guidelines provided by nationally recognized Safety
Organizations:
• Demandconstantsupervision.Acompetentadultshouldbeappointedasa“lifeguard”
or water watcher, especially when children are in and around the pool.
• Learntoswim.
• TakethetimetolearnCPRandfirstaid.
• Instructanyonewhoissupervisingpoolusersaboutpotentialpoolhazardsandabout
the use of protective devices such as locked doors, barriers, etc.
• Instructallpoolusers,includingchildrenwhattodoincaseofanemergency.
• Alwaysusecommonsenseandgoodjudgementwhenenjoyinganywateractivity.
• Supervise,supervise,supervise.
For additional information on safety, please visit
•TheAssociationofPoolandSpaProfessionals:TheSensibleWaytoEnjoyYour
Aboveground/Onground Swimming Pool www.nspi.org
• AmericanAcademyofPediatrics:PoolSafetyforChildrenwww.aap.org
• RedCrosswww.redcross.org
• SafeKidswww.safekids.org
• HomeSafetyCouncil:SafetyGuidewww.homesafetycouncil.org
• ToyIndustryAssociation:ToySafetywww.toy-tia.org
SAVE THESE INSTRUCTIONS
Page 2
(249PO) MODEL ECO7111 Cartridge Filter Pump & Saltwater System with E.C.O. ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016
English
249
PO
S AVE THESE INSTRUCTIONS
English
Page 29
Your Krystal Clear Saltwater System
®
has been manufactured using the highest quality
materials and workmanship. All Intex products have been inspected and found free of
defects prior to leaving the factory. This Limited Warranty applies only to the Krystal Clear
Saltwater System
®
and accessories listed below.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of
the initial retail purchase. Keep your original sales receipt with this manual, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty
is invalid.
Krystal Clear Saltwater System
®
Warranty – 2 Years
Titanium Electrode Warranty – 1 Year
E.C.O
.
electrode Warranty – 1 Year
Hoses,PlungerValves&FittingsWarranty–180days
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in the separate “Authorized Service Centers”
sheet. The Service Center will determine the validity of the claim. If the Service Center
directs you to return the product, please carefully package the product and send with
shipping and insurance prepaid to the Service Center. Upon receipt of the returned
product, the Intex Service Center will inspect the item and determine the validity of the
claim. If the provisions of this warranty cover the item, the item will be repaired or
replaced at no charge.
Any and all disputes regarding the provisions of this Limited Warranty shall be brought
before an informal dispute settlement board and unless and until the provisions of these
paragraphs are carried forth, no civil action may be instituted. The methods and
procedures of this settlement board shall be subject to the rules and regulations set
forthbytheFederalTradeCommission(F.T.C.).IMPLIEDWARRANTIESARELIMITED
TOTHETERMSOFTHISWARRANTYANDINNOEVENTSHALLINTEX,THEIR
AUTHORIZEDAGENTSOREMPLOYEESBELIABLETOTHEBUYERORANY
OTHERPARTYFORDIRECTORCONSEQUENTIALDAMAGESORLIABILITIES.
Some states, or jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This Limited Warranty does not apply if the products are subject to negligence, abnormal
use or operation, accident, improper operation, improper voltage or current contrary to
operating instructions, or to damage by circumstances beyond Intex’s control, including
but not limited to, ordinary wear and tear and damage caused by exposure to fire, flood,
freezing, rain, or other external environmental forces. This Limited Warranty applies only
to those parts and components sold by Intex. The Limited Warranty does not cover
unauthorized alterations, repairs or disassembly by anyone other than Intex Service
Center personnel.
DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN
OR REPLACEMENT. IF YOU ARE MISSING PARTS OR NEED
ASSISTANCE, PLEASE CALL US TOLL-FREE (FOR U.S. AND
CANADIAN RESIDENTS): 1-800-234-6839 OR VISIT OUR WEBSITE:
WWW.INTEXSTORE.COM.
Proof of Purchase must accompany all returns or the warranty claim will be invalid.
LIMITED WARRANTY
… 29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex ECO7111 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex ECO7111 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info