686131
18
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
329
A
SAVE THESE INSTRUCTIONS
English
(329IO) MODEL ECO 5220/5230 & 6220/6230 SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 06/05/2018
Page 18
OPERATION INSTRUCTIONS (continued)
6. Boost cycle
First time installation, press and hold “BOOST” button for 5 seconds until
the indicator lights up and the LED display “80”. This indicates that the
saltwater system has started more chlorine sanitizer production. You can
press and hold the “BOOST” button for another 5 seconds until the indicator
is off, which will cancel the Boost cycle.
The boost operating hours is 8 times the amount of time programmed into the
system, i.e. if your saltwater system operating time is 2 hours, the boost procedure will run 8 x 2 =
16 hours. After boost procedure has been completed, the system will automatically switch to
the normal working mode.
Once the boost is operating, check whether the filter pump operating hours have been set
properly. For example, the boost operating time is 8 hours, the filter pump should be set to
run for 8 hours at least. Increase the filter pump operating time if necessary.
NOTE: If an Intex filter pump is attached to the system, set the pump switch to on “I”
position.
After a heavy rain or if the pool is dirty, press the “BOOST” button to shock
the pool again.
7. Stand-by/power saving mode:
When the cycle ends, the green “SLEEP” indicator on the control panel
lights up and the LED display flashes “93”. The system is now in Stand-By
mode. After a while, it shuts down and sets itself in a Power Saving mode.
The system will automatically turn itself back on in 24 hours,
starting its daily cycle of chlorine production.
The “SLEEP” indicator stays on, while the system is in the Power Saving
mode. The LED display however, goes blank after 5 minutes. Press any
button ( or ) to view the last LED code.
8. Electrode Self-Clean cycle:
Press and hold button for 5 seconds until the LED display flashes
“10”. Depending on your pool water calcium hardness level, press
button again to select the self-clean cycle time as below. Total of 3
settings: 14 hours, 10 hours and 06 hours.
NOTE: The life of the cell varies depending on water conditions, pool usage and operating
time of the device. Select 14 hours cycle time to maximize the life of the electrolytic cell if
the calcium hardness level is up to 150 ppm. Manual routine cleaning and maintenance will
further lengthen the life of the electrolytic cell.
With the desired self-clean hours showing, press button to lock the keypad controls and
the LED display will return to the normal operating time. The system will reverse the polarity
of the electrode (5) every time according to the selected hours.
NOTE: If you forget to lock the keypad controls, the system will automatically lock it.
Calcium Hardness Self-clean cycle time
0 - 150 ppm Reverse polarity every 14 hours
150 - 250 ppm Reverse polarity every 10 hours
250 - 350 ppm Reverse polarity every 06 hours
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex ECO5230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex ECO5230 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Intex ECO5230

Intex ECO5230 Gebruiksaanwijzing - Nederlands - 29 pagina's

Intex ECO5230 Gebruiksaanwijzing - Deutsch - 28 pagina's

Intex ECO5230 Gebruiksaanwijzing - Français - 29 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info