752333

Intex CS8221 Handleiding

1
Verklein
Vergroot
Pagina terug
1/35
Pagina verder
134A
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
OOWWNNEERR’’SS MMAANNUUAALL
Krystal ClearTM
Saltwater System
& Filter Pump
Model CS8221 220 - 230 V~,
Model CS8231 230 - 240 V~
IMPORTANT
SAFETY RULES
Read, understand, and follow all
instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool accessories,
inflatable pools and in-home toys, airbeds and boats available at fine
retailers or visit our website.
For illustrative purposes only.
©2011 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European
Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., P.O. Box nr. 1075 – 4700 BB Roosendaal – The Netherlands
134-*A*-R1-1211
134A
SAVE THESE INSTRUCTIONS
English
Page 2
TTAABBLLEE OOFF CCOONNTTEENNTTSS
Warnings............................................................................... 3
Parts List & References....................................................... 4-9
Product Information & Specifications................................ 10
Setup Instructions............................................................... 11-14
Salt & Pool Water Volumes.................................................. 15
Intex Pools Salt Table........................................................... 16
Intex Pools Operating Time Table ...................................... 17
Intex Pools Cyanuric Acid Table......................................... 18
Non-Intex Pools Salt Table.................................................. 19
Non-Intex Pools Operating Time Table............................... 19
Non-Intex Pools Cyanuric Acid Table................................. 19
Operating Instructions......................................................... 20-22
LED Code Chart................................................................... 23
Stationary Mounting Option................................................ 24
Maintenance......................................................................... 25-28
Long Term Storage.............................................................. 28
Pool Maintenance and Chemical Definitions.................... 29
Troubleshooting Guide........................................................ 30-32
General Aquatic Safety....................................................... 33
Limited Warranty.................................................................. 34
Intex Service Center Locations.......................................... 35
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 3
SSAAFFEETTYY RRUULLEESS
WARNING
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
For portable Above-Ground-Pools only
•To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
•Children must stay away from this product and electrical cord(s).
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge. They
must at all times be supervised by a knowledgeable and experienced adult
responsible for their safety.
•Assembly and disassembly by adults only.
•Risk of electric shock. Connect this product only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI) or residual current device
(RCD). Contact a qualified electrician if you cannot verify that the receptacle is
protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD,
which has a maximum rate of 30mA. Do not use a portable residual current device
(PRCD).
•Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
• The plug must be accessible after produc t is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
•If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
•To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
•Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
•Keep this product more than 2m away from the pool.
•Keep this product more than 3.5m away from the pool (for France only).
•Keep the plug of this product more than 3.5m away from the pool.
• Position this product away from the pool, so as to prevent children from climbing on
it and accessing the pool.
•Do not operate this product when the pool is occupied.
•This product is for use with storable pools only. Do not use with permanently
installed pools. A storable pool is constructed so that it may be readily
disassembled for storage and reassembled to its original configuration.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 4
PPAARRTTSS LLIISSTT
PARTS LIST
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
7
1
9
4 5
2
6
3
8
10 11 12
13 14 15
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 5
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
PPAARRTTSS LLIISSTT
16 17 18
19 20 21
22 23 24
25 26 27
28
31 32
29 30
* Optional
* Optional * Optional
* Optional
PARTS LIST (continued)
33
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 6
PPAARRTTSS RREEFFEERREENNCCEE
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
1
2
3
4
5
68
7
1
2
10
9
8 12 13 12
14
15 16 17 30
18
11
33
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 7
PPAARRTTSS RREEFFEERREENNCCEE
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
When ordering parts, be sure to quote the model number and part numbers.
REF. NO. DESCRIPTION QTY. SPARE PART
NO.
33 COPPER ELECTRODE NUT 1 11488
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
AIR RELEASE VALVE/SEDIMENT RELEASE VALVE
VALVE O-RING
THREADED FILTER HOUSING COLLAR
FILTER HOUSING COVER
FILTER HOUSING O-RING
FILTER CARTRIDGE (59905)
AIR RELEASE VALVE B (WITH O-RING)
PUMP HOSE WITH NUTS
WATER TRANSFER HOSE (WITH COLLAR AND 2 HOSE CLAMPS)
SCREW
FLOW SENSOR
O-RING A
ELECTROLYTIC CELL (WITH TITANIUM
PLATES) (O-RING A INCLUDED
COPPER ELECTRODE
FLOW SENSOR CONDUIT
O-RING C
ANGLE JOINT (O-RING D INCLUDED)
O-RING D
2
2
1
1
1
1
1
2
1
2
1
2
1
1
1
1
1
1
10460
10264
10491
10490
11330
10725
10494
10726
10713
11460
10712
11233
11234
11251
10717
10724
10743
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 8
PPAARRTTSS RREEFFEERREENNCCEE
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
19
20
21 22 23 24 25
19
20
21 26 27 28
19
20
21 22 23 24
19
20
21 26 27 29
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 9
SPARE PART
NO.
10747
10262
10745
10256
10255
11235
11074
10722
11070
11071
11072
11131
19635
11254
QTY.
2
2
2
2
1
2
2
1
1
1
1
1
DESCRIPTION
PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED)
HOSE O-RING
STEP WASHER
STRAINER NUT
FLAT STRAINER RUBBER WASHER
THREADED STRAINER CONNECTOR
ADJUSTABLE POOL INLET NOZZLE
ADAPTOR B (OPTIONAL)
STRAINER CONNECTOR (OPTIONAL)
POOL INLET NOZZLE (OPTIONAL)
STRAINER GRID (OPTIONAL)
CELL COVER
CHLORINE TEST STRIPS
COPPER TEST STRIPS
REF. NO.
COMMON
19
20
21
30
31
32
LARGE AGP
22
23
24
25
SMALL AGP
26
27
28
29
PPAARRTTSS RREEFFEERREENNCCEE
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 10
PPRROODDUUCCTT IINNFFOORRMMAATTIIOONN//SSPPEECCSS
This product is specially designed for above ground pools. It will destroy the
bacteria, oxidize bather organics and control algae, which provide you a safe, clean
and comfortable swimming pool.
Common salt (sodium chloride) is made up of two elements, sodium and chlorine.
During the installation of your Saltwater System/Filter Pump, a measured quantity
of salt is dissolved in the pool water to make it slightly salty. The pool water flows
through the saltwater system’s electrolytic cell to produce HCLO. The HCLO
dissolves in the water and instantly starts destroying bacteria and algae. It
also oxidizes all other organic materials.
Low voltage direct current is applied to the copper electrode, and copper ions are
generated and dissolved instantly in the water. Copper is an effective algaecide,
which will prevent algae from growing in the pool.
HOW THE CHLORINE IS GENERATED
Wattage: 400W
Ideal Salt Level: 3000 ppm (parts per million)
Maximum Chlorine Output/hour: 12 grams/hour
Copper Ionizer Output Current: 175 mA
Limited Warranty: see “Limited Warranty”
HOW COPPER IONS ARE GENERATED
PRODUCT SPECIFICATIONS
Flow Sensor
Electronic
Control Station
Electrolytic Cell
Water Outlet
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 11
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
STRAINER & PLUNGER VALVE SETUP
IMPORTANT
The Saltwater System/Filter Pump must be installed as the last piece of
pool equipment in the water return line to the pool. This location extends
the life of the titanium plates.
Strainer & Plunger Valve Setup (small AGP)
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. The plunger valve assembly prevents water from flowing into the
filter pump while the filter cartridge is being placed or cleaned. If your pool
has an inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The parts numbers here onward, refer to the
parts depicted in the Parts List section of this manual. To install, do the
following:
1. Grasp the strainer and plunger valve mechanism.
2. In a counter-clockwise motion unscrew plunger valve union from the threaded
strainer connector (24). Be careful not to lose the step rubber washer (21).
3. Grasp the plunger valve assembly. Make sure the step washer (21) is in place.
Connect adaptor B (26) to plunger valve union.
4. Repeat steps 1 through 3 for nozzle and plunger valve mechanism.
5. Remove wall plug and then insert the strainer (27 & 29) into the lower position
of protruding hose connection, and the nozzle (27 & 28) into the upper position
of protruding hose connection. Adaptor B (26) fits over the strainer
connection (27) inserted into the connection.
6. Examine the plunger valve to see if the handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at the top and push down turning the
handle in a clockwise direction until the plastic protruding notch anchor is in
the "0/1" position. This will prevent water from flowing out during filling.
7. The pool liner is now ready to fill with water. Consult the above-ground-pool
owner's manual for filling instructions.
19
20
21 26 27 28
19
20
21 26 27 29
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 12
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
STRAINER & PLUNGER VALVE SETUP (continued)
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. If your pool has an inflatable top ring, install the strainer, nozzle
and plunger valve before inflating the pool liner top ring. The part numbers
here onward refer to the parts depicted in the Parts List section of this
manual. To install, do the following:
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (24) (see drawing 1).
Be careful not to lose the step rubber
washer (21). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (22) from the threaded
connector (24). Leave the flat washer (23)
on the connector (24).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
From the inside of the pool liner insert the
connector (24) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. Then, with the flat side of
the strainer nut (22) facing the outside wall
of the liner in a clockwise motion screw the
strainer nut (22) back onto the threaded
connector (24) (see drawing 2).
5. Finger tighten the strainer nut (22) onto the
threaded connector (24).
6. Grasp the plunger valve assembly. Make
sure the step washer (21) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (24) (see drawing 3).
8. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, grasp the handle at the
top and push down, turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling of the pool (see
drawings 4.1 & 4.2).
1
2
3
4.1
4.2
23 24
21
INSIDE
LINER WALL
INSIDE
LINER
WALL
22
2
1
1
2
1
2
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 13
NOZZLE & PLUNGER VALVE SETUP
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
1.In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (24) (see drawing 5).
Be careful not to lose the step rubber
washer (21). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (22) from the threaded
connector (24). Leave the flat washer (23)
on the connector (24).
3. Install the nozzle and plunger valve at the
upper position of the pool inlet. From the
inside of the pool liner insert the
connector (24) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. Then, with the flat side of
the strainer nut (22) facing the outside wall
of the liner in a clockwise motion screw the
strainer nut (22) back onto the threaded
connector (24) (see drawing 6).
5. Finger tighten the adjustable pool inlet
nozzle (25) and the strainer nut (22) onto
the threaded connector (24).
6. Grasp the plunger valve assembly. Make
sure the step washer (21) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (24) (see drawing 7).
8. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at
the top and push down turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling of the pool (see
drawings 8.1 & 8.2).
9. Adjust the direction of the nozzle head
pointing away from the pool outlet for a
better circulation result (see drawing 9).
10. The pool liner is now ready to be filled with
water. Consult the above-ground-pool
owner’s manual for the filling instructions.
5
7
8.1
8.2
INSIDE
LINER
WALL
POOL
9
2
1
1
2
1
2
6
23 24 25
INSIDE
LINER WALL
22
WATER
FLOW
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 14
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
SALTWATER SYSTEM/FILTER PUMP
Saltwater System/Filter Pump
1. Remove the Saltwater System/Filter Pump and hoses from the packaging.
2. Place the Saltwater System/Filter Pump in a location for hose (8) connections
to the plunger valve assemblies.
NOTE: Some regional regulations may require the filter pump to be
mounted on a stationary platform. There are two mounting holes located
in the pump base for this reason. Consult your local authorities for filter
pump mounting requirements.
3. Grasp the two pump hoses (8) and connect the hose nuts to the Saltwater
System/Filter Pump.
4. In a counter-clockwise motion unscrew the threaded filter housing collar (3)
from the filter housing. Place it in a safe place.
5. The Saltwater System/Filter Pump is an airtight system. In a counter-clockwise
motion turn both air release valves (1 & 7) 1 - 2 turns to open. DO NOT remove
air release valves as water will expel with force if the motor is turned on
and injury may occur.
6. Grasp and remove the filter housing cover (4). Check to see if a cartridge is
inside the housing. If yes, replace the cover, finger tighten the housing collar (3)
back onto the filter housing.
7. Gently finger tighten the sediment release valve located at the bottom of the
housing to be sure that water does not leak out.
8. When the pool is filled connect the hose from the electrolytic cell outlet to the
highest strainer assembly. You will find the hose connection at the bottom of the
plunger valve assembly. Use the hose nut to attach the hose.
9. Connect the second hose to the middle of the motor housing and to the
remaining liner connection.
IMPORTANT
To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open air
release valves, lift and lower the inlet hose until water starts to flow out of
the air release valves, close air release valves.
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 15
SSAALLTT && PPOOOOLL WWAATTEERR VVOOLLUUMMEESS
SALT & POOL WATER VOLUMES
• Which kind of salt to use:
Use only Sodium Chloride Salts
Use only sodium chloride (NaCl) salt that is at least 99.8% pure. It is also
acceptable to use water conditioning salt pellets (the compressed forms of
evaporated salt). However, it will take a longer time for them to dissolve. Do not use
iodized or yellow (yellow prussiate of soda) colored salt. Salt is added to the
pool water and the electrolytic cell uses the salt to create the sanitizer. So, the purer
the salt the better the performance of the electrolytic cell.
• Optimum Salt Levels
The ideal salt level in the pool water is between 2500-3500 ppm (parts per million).
The optimal level is 3000 ppm.
A too low salt level will reduce the efficiency of the saltwater system and result in
low sanitizer production. A high salt level may generate a salty taste to the pool
water (this may occur at a salt level above 3500-4000ppm). Too high of a salt level
may damage the power supply and cause corrosion to pool metal fixtures and
accessories. The Salt Table page of this manual, shows the correct dosage of salt
needed. The salt in the pool is constantly recycled. Salt loss occurs only when pool
water is physically removed from the pool. Salt is not lost due to evaporation.
• Adding Salt
1. Switch on the unit, then press and hold both and button for 5 seconds,
the LED flashes “FP”. The unit is now in a Filter pump working mode and
switch the filter pump on to start the water circulation.
2. Keep the Saltwater System turned off.
3. Determine the amount of salt to be added (see “Salt Table”).
4. Evenly spread the proper amount of salt around the inside perimeter of the
pool.
5. Avoid clogging the filter by not adding salt through the skimmer.
6. Brush the pool bottom to speed up the dissolving process. Do not allow salt to
pile up on the bottom of the pool. Run the filter pump 24 consecutive hours to
thoroughly dissolve the salt.
7. After 24 hours and if all the salt is dissolved, turn on the Saltwater System,
press button until you hear a “beep”, code “00” flashing (see “System
Operation” section steps 2 to 4) and set the saltwater pool system to desired
operating time (see “Operating Time Table”).
• Removing Salt
If too much salt has been added, the unit will beep and display “Code 92” (see
“Alarm Codes”). You will need to lower the salt concentration. The only way to do so,
is to partially drain the pool and refill it with fresh water. Drain and refill
approximately 20% of the pool’s water until the “Code 92” disappears.
• Pool Volume Calculation
Rectangular
Length x Width x Average Depth x 7.5 Length x Width x Average Depth
Circular
Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79
Oval
Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80
Types of Pool Gallons
(pool size in feet)
Cubic Meters
(pool size in meters)
134A
SAVE THESE INSTRUCTIONS Page 16
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
INTEX POOLS SALT TABLE
This table shows the amount of salt needed to achieve and maintain the optimal 3000 ppm
salt level.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Salt Needed for
Startup
3.0g/L (3000ppm)
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (569cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587 9792 65 30 20 10
2822 10681 65 30 20 10
3284 12430 80 35 20 10
3736 14141 95 45 20 10
3754 14209 95 45 20 10
4273 16173 110 50 30 15
4786 18115 120 55 30 15
5455 20647 135 60 35 15
5894 22309 150 65 40 20
3282 12422 80 35 20 10
3861 14614 100 45 20 10
4440 16805 110 50 30 15
5061 19156 125 55 30 15
6423 24311 160 75 40 20
6981 26423 175 80 45 20
8638 32695 220 100 60 25
11483 43462 290 130 75 35
12481 47241 310 140 85 40
5061 19156 125 55 35 15
6981 26423 175 80 45 20
5061 19156 125 55 35 15
6981 26423 175 80 45 20
2885 10920 65 30 20 10
4393 16628 110 50 30 15
5407 20465 135 60 35 15
6420 24300 160 75 40 20
4545 17203 115 50 30 15
8403 31805 210 100 55 25
14364 54368 360 165 95 45
134A
SAVE THESE INSTRUCTIONS Page 17
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
INTEX POOLS OPERATING TIME TABLE (WITH CYANURIC ACID)
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Operating Time (hours)
at different ambient/air
temperatures
(Gals) (Liters)
10 - 19°C
(50 - 66°F)
20 - 28 °C
(68 - 82 °F)
29 - 36 °C
(84 - 97 °F)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (
569
cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587
2822
3284
3736
3754
4273
4786
5455
5894
3282
3 861
4440
5061
6423
6981
8638
11483
12481
5061
6981
5061
6981
2885
4393
5407
6420
4545
8403
14364
9792
10681
12430
14141
14209
16173
18115
20647
22309
12422
14614
16805
19156
24311
26423
32695
43462
47241
19156
26423
19156
26423
10920
16628
20465
24300
17203
31805
54368
1
1
1
1
1
2
2
2
2
1
1
2
2
2
2
3
4
5
2
2
2
2
1
2
2
2
2
3
6
1
1
1
2
2
2
2
2
2
1
2
2
2
2
2
3
4
5
2
2
2
2
1
2
2
2
2
3
6
1
1
2
2
2
2
2
3
3
2
2
2
2
3
3
4
5
6
2
3
2
3
1
2
3
3
2
4
7
134A
SAVE THESE INSTRUCTIONS Page 18
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
INTEX POOLS CYANURIC ACID TABLE
Cyanuric acid is a chemical that reduces the loss of chlorine in water due to ultraviolet rays. To
maintain maximum performance, we recommend that the cyanuric acid level be maintained at
approximately 1% of the salt, i.e. 100 Lbs (45 Kgs) salt x1% = 1 Lbs (0.45 Kgs) cyanuric acid.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Cyanuric Acid Needed for
Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME®
POOL
SEQUOIA SPIRIT®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (
569
cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587 9792 0.6 0.3
2822 10681 0.7 0.3
3284 12430 0.8 0.4
3736 14141 0.9 0.4
3754 14209 0.9 0.4
4273 16173 1.1 0.5
4786 18115 1.2 0.5
5455 20647 1.4 0.6
5894 22309 1.5 0.7
3282 12422 0.8 0.4
3861 14614 1.0 0.4
4440 16805 1.1 0.5
5061 19156 1.3 0.6
6423 24311 1.6 0.7
6981 26423 1.7 0.8
8638 32695 2.2 1.0
11483 43462 2.9 1.3
12481 47241 3.1 1.4
5061 19156 1.3 0.6
6981 26423 1.7 0.8
5061 19156 1.3 0.6
6981 26423 1.7 0.8
2885 10920 0.7 0.3
4393 16628 1.1 0.5
5407 20465 1.4 0.6
6420 24300 1.6 0.7
4545 17203 1.1 0.5
8403 31805 2.1 1.0
14364 54368 3.6 1.6
134A
SAVE THESE INSTRUCTIONS Page 19
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
SALT TABLE FOR COMMON NON-INTEX POOLS
OPERATING TIME TABLE FOR COMMON NON-INTEX POOLS
SALT CALCULATION FORMULA FOR ALL POOLS
Water Capacity Salt Needed for Startup
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
2000 7500 50 20 10 5
4000 15000 100 45 25 10
6000 22500 150 65 40 20
8000 30000 200 90 55 25
10000 37500 250 110 70 30
12000 45500 300 135 80 35
14000 53000 350 160 95 45
Salt Needed for Startup
(Lbs)
Salt Needed for Startup
(Kgs)
Salt Needed when
Low Salt Detected (Lbs)
Salt Needed when
Low Salt Detected (Kgs)
Water Capacity (Gals) x 0.025
Water Capacity (Liters) x 0.003 Water Capacity (Gals) x 0.0067 Water Capacity (Liters) x 0.0008
CYANURIC ACID TABLE FOR COMMON NON-INTEX POOLS
Water Capacity Operating Time (hours)
at different ambient/air temperatures
(Gals) (Liters) 10 - 19°C
(50 - 66°F)
20 - 28 °C
(68 - 82 °F)
29 - 36 °C
(84 - 97 °F)
2000
4000
6000
8000
10000
12000
14000
7500
15000
22500
30000
37500
45500
53000
1
2
2
3
4
5
6
1
2
3
4
5
6
7
1
2
2
3
4
5
6
Water Capacity Cyanuric Acid Needed for Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
2000
4000
6000
8000
10000
12000
14000
7500
15000
22500
30000
37500
45500
53000
0.23
0.45
0.68
0.90
1.13
1.37
1.59
0.5
1.0
1.5
2.0
2.5
3.0
3.5
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 20
FILTER PUMP OPERATION
OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS
1. Make sure the unit is switched off. The switch is located on the control station.
2. Connect the power cord to a GFCI/RCD protected electrical outlet.
3. Grasp a plunger valve handle. Turn the handle counter-clockwise, pull up until it
stops, and then turn it clockwise until the metal protruding notch anchor is in
the "0/1" position. Repeat for the second plunger valve. This opens the valves,
allowing water to flow into the unit.
4. With water flowing into unit, the water pressure will allow the air trapped inside
to escape from the air release valves (1 & 7). When all the air has escaped
water will flow out of the valves (1 & 7). When this occurs gently finger tighten
the valves in a clockwise direction.
5. Turn on the switch. The filter pump is now filtering the water.
6. The green "Pump" light on the control panel will light up, that indicates the filter
pump is running.
To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open air
release valves, lift and lower the inlet hose until water starts to flow out of
the air release valves, close air release valves.
IMPORTANT
71
WARNING
Risk of electric shock. Connect this product only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI) or residual
current device (RCD). Contact a qualified electrician if you cannot verify
that the receptacle is protected by a GFCI/RCD. Use a qualified electrician
to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a
portable residual current device (PRCD).
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 21
SALTWATER SYSTEM OPERATION
OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS
1.Start up the unit:
Plug the power cord into the electrical outlet and test the
GFCI/RCD (circuit breaker). Switch on the unit.
With the Filter Pump turned “ON” and operating. The
green "Pump" light on the control panel will be on
and flashing code “00” appears on the electronic control
station’s LED, indicating that the unit is ready to be
programmed. This is normal.
2.Set operating hours for Saltwater System:
With code “00” flashing, press button to
set the desired operating hours. See the
“Operating Time Table” for the required
operating hours related to each pool size.
Pressing will increase the time from 01
to 12 hours maximum. If you have selected
too many hours keep pressing to repeat
the cycle. The built-in timer will now activate
your Saltwater System, at the same time each
day, for the number of hours you have set.
NOTE: The Saltwater System will not
operate if the filter pump is not operating.
3.Lock keypad controls:
With the desired hour value showing, press button
until you hear a “beep”. The green “WORKING”
indicator on the control panel will light up within a few
seconds to indicate that the saltwater system has started
sanitizer production. Locking the control buttons into this
setting prevents unauthorized changing of the operating
cycle.
NOTE: If you forget to lock the keypad controls, the
system will automatically lock it and start working 1
minute later.
4. Unlock & Readjust operating time if necessary:
The operating hours can be re-adjusted if necessary.
Press button until you hear a “beep” to unlock the keypad and the
current programmed time will flash. Repeat steps 2 to 3.
5.Test the copper concentration in
the pool water.
The Saltwater System recommends
a copper level of 0.1 to 0.2 ppm.
This is easily tested by the copper
ion test strips provided. If the test
result is 0.1~0.2ppm, go directly to
step 7.
(1 to 12 hours max per cycle)
OK
0
Copper (ppm)
0.1 0.2 0.5 0.9 1.3
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 22
SALTWATER SYSTEM OPERATION (continued)
OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS
6.Boost cycle
•If the test result is below 0.1ppm, press and hold “BOOST”
button for 5 seconds until the indicator lights up and the
LED display display “80”. This indicates that the saltwater
system has started copper ion and more chlorine sanitizer
production.
You can press and hold the “BOOST” button for another 5
seconds until the indicator is off, which will cancel the Boost
cycle.
Note: Once the system has started copper ion and more chlorine sanitizer
production, the boost button can’t be re-set until the power switch is off.
•The boost operating hours is 4 times the amount of time programmed into the
system, i.e. if your saltwater system operating time is 2 hours, the boost procedure
will run 4 x 2 = 8 hours. After boost procedure has been completed, the system
will automatically switch to the normal working mode.
•After a heavy rain or if the pool is dirty, press the “BOOST” button to shock the
pool again.
7.Test pool water regularly:
Once the copper level appears to be balanced, test the pool water every week
to maintain the proper sanitizer level.
It’s very important that the free chlorine is between 0.4-1.5 ppm and copper
ion concentration is between 0.1~0.2 ppm. When the copper level is below 0.1
ppm, repeat step 6.
NOTE: A High copper ion concentration may cause blonde hair to exhibit a
green hair. To prevent this, wear a swimming cap during swimming, and wash
hair with special shampoo after using the pool.
See “Troubleshooting Guide”.
8. Stand-by/power saving mode:
•When the cycle ends, the green “SLEEP” indicator on the
control panel lights up and the LED display flashes “93”.
The system is now in Stand-By mode. After a while, it
shuts down and sets itself in a Power Saving mode. The
system will automatically turn itself back on in 24 hours,
starting its daily cycle of chlorine production.
•The “SLEEP” indicator stays on, while the system is in the
Power Saving mode. The LED display however, goes blank
after 1 hour. Press any button ( or ) to view the last LED
code.
9. Running the pump alone without the Saltwater System:
To run the pump alone without the Saltwater System function,
press and hold both and buttons until you hear a “beep”,
the LED display will show “FP”. The pump is now operating
alone. NOTE: The pump cannot be operated alone under an
automatic timer mode. To stop the pump, manually turn
the switch OFF.
IMPORTANT: To keep the initial automatic operating cycle
setting of the Saltwater System, turn the switch ON, the LED
display will show “FP”, and then press until you hear a “beep”.
The LED display will now show the initial input hours and the Saltwater System
cycle will repeat again.
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 23
LLEEDD CCOODDEE CCHHAARRTT
LED CODE CHART
LED Reading Definitions
FP Filter Pump Working Mode
80 Boost Mode
00 Stand-By Mode (Start-up)
01 Minimum Operating Hour (1 hour remaining)
02 Operating Hours (2 hours remaining)
03 Operating Hours (3 hours remaining)
04 Operating Hours (4 hours remaining)
05 Operating Hours (5 hours remaining)
06 Operating Hours (6 hours remaining)
07 Operating Hours (7 hours remaining)
08 Operating Hours (8 hours remaining)
09 Operating Hours (9 hours remaining)
10 Operating Hours (10 hours remaining)
11 Operating Hours (11 hours remaining)
12 Maximum Operating Hours (12 hours remaining)
90 Alarm Code (Low Water Flow / No Flow)
91 Alarm Code (Low Salt Level)
92 Alarm Code (High Salt Level)
93 Stand-By Mode (Operating Process finished)
“BLANK” No Power or “Power Saving Mode” waiting to start next
Saltwater System cycle.
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 24
SSTTAATTIIOONNAARRYY MMOOUUNNTTIINNGG OOPPTTIIOONN
Some countries, especially in the European community, require the product
to be secured to the ground or to a base in a permanent upright position.
Check your local authorities to determine if there is a regulation in your
area regarding above-the-ground swimming pool filter-pumps. If yes, then
the product can be mounted to a platform using the two holes located in
the base. See drawing below.
The product can be mounted on a cement base or onto a wooden platform
to prevent accidental falling over. Total assembly must exceed 18kg. The
European norm EN 60335-2-41 requires this product be secured to the
ground or to a base.
1. The mounting holes are 6.4 mm in diameter and spaced 506 mm apart.
2. Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.
506 mm
SALTWATER SYSTEM/FILTER PUMP STATIONARY MOUNTING
OPTION
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 25
MMAAIINNTTEENNAANNCCEE
MAINTENANCE
IMPORTANT
Close plunger valves on your pool or insert black hat-like plugs in strainer
opening to prevent water spillage. Open plunger valves or remove plugs
when maintenance is completed.
1. In a counter-clockwise motion unscrew the collar of the flow sensor (11) and
remove it from the flow sensor conduit (15). See “Part Reference”.
2. If deposits and debris are seen on the surface of the flow sensor, then use a
garden hose to wash it off.
3. If flushing with water does not remove the deposits, use a plastic brush to
clean the surface and the hinge if necessary. Do not use a metal brush.
4. After the flow sensor has been inspected and cleaned, align the locator notch
on the flow sensor to the connection ridge in the conduit. Now turn the collar in
a clockwise motion, tightening the sensor back into its position. Do not
overtighten.
The electrolytic cell (13) has a self cleaning function incorporated into the electronic
control's programming. In most cases this self cleaning action will keep the cell
working at optimum efficiency. If the pool water is hard (high mineral content) the
cell may require periodic manual cleaning. To maintain maximum performance, we
recommend that you open and visually inspect the electrolytic cell (13) once every
month.
The following steps provide instructions on how to clean your cell.
Connection Ridge
Locator Notch
Hinge
FLOW SENSOR CLEANING
ELECTROLYTIC CELL CLEANING
WARNING
Always unplug this product from the electrical outlet before removing,
cleaning, servicing or making any adjustment to the product.
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 26
MMAAIINNTTEENNAANNCCEE
MAINTENANCE (continued)
1. Switch off the unit, unplug the power cord from the electrical socket.
2. Grasp a plunger valve handle. Turn the handle counter-clockwise, push down
until it stops and then turn it clockwise until the plastic protruding notch anchor
is in the "0/I" position. Repeat for the second plunger valve. This prevents the
water from flowing out of the pool.
3. Disconnect the hose with nut (8) from the Saltwater System, and assemble the
cell cover (30) at the side of the cell.
4. In a counter-clockwise motion, unscrew the collar of the copper electrode (14)
and remove it from the electrolytic cell (13). Lift up the copper electrode.
5. Pour kitchen grade vinegar into the cell to immerse the titanium plates. Then
put the copper electrode back in the cell, soak them for about one hour until
no colored areas remain.
6. Open one side of the cell cover (30), drain and properly dispose of the vinegar.
Connect the hose which goes from the pool to the cell. Flush the cell with the
pool water.
7. Reverse steps 3, 4, 5 and 6 to reconnect the electrolytic cell.
30
8
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 27
MMAAIINNTTEENNAANNCCEE
It is recommended that the filter cartridge be replaced at least every 2 weeks.
1. Make sure the unit is turned off, and disconnect the power cord from the
electrical outlet.
2. Grasp a plunger valve handle. Turn the handle counter-clockwise, push down
until it stops and then turn it clockwise until the plastic protruding notch anchor
is in the "0/1" position. Repeat for the second plunger valve. This prevents the
water from flowing out of the pool.
3. Gently turn both air release valves (1 & 7) once or twice in a counter-clockwise
direction. The housing cover can now be easily removed.
4. In a counter-clockwise direction remove the filter housing collar (3). Place it in
a safe location.
5. Remove the housing cover (4).
6. Now remove the used filter cartridge.
7. Examine the inside of the filter housing.
8. If dirt or sediment is located on the bottom of the housing then:
A. In a counter-clockwise motion gently unscrew and remove the sediment
valve (1) located at the bottom of the housing. Place it in a safe place.
B. With a bucket of water or a garden hose pour water into the housing
flushing out the sediment.
C. Screw back the sediment valve (1) in a gentle clockwise motion. Do not
over-tighten.
9. Place a new cartridge filter in the housing.
10. Return the housing cover (4) to its installed position and in a clockwise
direction rescrew the housing collar (3) onto the filter housing.
11. Turn both plunger valve handles in a counter-clockwise direction, pull up until
they stop, and then turn them clockwise until the metal protruding notch
anchor is in the "0/1" position.
12. Reconnect the power cord.
13. Turn on the unit.
14. When the trapped air has escaped through the air release valves gently
retighten the valves (1 & 7) in a clockwise direction.
CLEANING OR REPLACING FILTER CARTRIDGES
MAINTENANCE (continued)
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 28
MMAAIINNTTEENNAANNCCEE
MAINTENANCE (continued)
The Copper Ion Test Strips can be used to test the copper ion concentration in the
water.
Directions and Use
1. Dip the entire strip into the water for 3 seconds, then remove it.
2. Hold the strip level for 15 seconds. Do not shake excess water from the strip.
3. Now compare the copper ion strip pad to the color chart on the packaging
label.
The 3-Way Test Strips can test the “Free Chlorine”, “pH”, and “Total Alkalinity” levels
at the same time. We recommend that you test the water chemistry weekly, and
maintain the chlorine concentration at 0.4-1.5 ppm.
Directions and Use
1. Dip the entire strip into the water and remove immediately.
2. Hold the strip level for 15 seconds. Do not shake excess water from the strip.
3. Now compare the strip pad to the color chart on the packaging label. If
necessary, adjust the chemical level in the pool water. It is very important, to
use the proper technique when testing the water's chemical level. Read and
follow the written strip instructions carefully.
1. Disconnect the power cord from the electrical outlet.
2. After the pool is completely empty, disconnect the Saltwater System from the
hoses by reversing the installation instructions.
3. Air-dry the unit before you store it. This might be a good time to visually inspect
and clean the electrolytic cell.
4. Store the unit and accessories in a dry place. The temperature should be
controlled, between 32 degrees Fahrenheit (0 degrees Celsius) and 97
degrees Fahrenheit (36 degrees Celsius).
5. The original package can be used for storage.
INTEX®3-WAY TEST STRIPS (PACKED WITH THE PRODUCT)
LONG TERM STORAGE
INTEX®COPPER ION TEST STRIPS (PACKED WITH THE PRODUCT)
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 29
POOL MAINTENANCE & CHEMICAL DEFINITIONS
MMAAIINNTTEENNAANNCCEE
Free
Chlorine
-Is the sanitizer (HCLO) residual present in pool water.
Combined
Chlorine
-Is formed by the reaction of free Chlorine with ammonia
wastes.
Result if too high - Sharp chlorinous odor, eye irritation.
pH
- A value that indicates how acidic or basic a solution is.
Result if too low - Corroded metals, eye & skin irritation,
destruction of total alkalinity.
Result if too high - Scale formation, cloudy water, shorter
filter runs, eye & skin irritation, poor
Chlorine efficiency.
Total Alkalinity -Indicates the degree of the water's resistance to change
in pH. It determines the speed and ease of pH change,
so always adjust total alkalinity before adjusting the pH
level.
Result if too low - Corroded metals, eye & skin irritation.
Low alkalinity will cause the pH to be
unstable. Any chemical added to the
water will have an affect on pH.
Result if too high - Scale formation, cloudy water,
eye & skin irritation, poor Chlorine
efficiency.
Calcium Hardness -Refers to the amount of calcium and magnesium
dissolved in the water.
Result if too high - Scale will form and will cause the
water to become cloudy.
Stabilizer -Stabilizers extend the life of Chlorine in swimming pools.
(Cyanuric Acid)
Consult with local swimming pool dealer for water treatment.
HCLO - A very effective killer of algae and bacteria known as hypochlorous acid.
• Do not add pool chemicals directly to the skimmer. This may damage the cell.
• Maintaining a high salt and sanitizer levels above recommended range can
contribute to corrosion of pool equipment.
• Check the expiry date of the test kit as the test results may be inaccurate if the
kit is used after that date.
• If, due to heavy pool usage, it is required to increase the sanitizer level, then use
a chemical based on Trichloro-s-triazinetrione or sodium dichloro-s-triazinetrione
dihydrate.
Preferred Water Chemistry Reading
Minimum Ideal Maximum
Copper Ions 0 0.1 - 0.2 ppm 0.2 ppm
Free Chlorine 0 0.4 - 1.5 ppm 3.0 ppm
Combined Chlorine 0 0 ppm 0.2 ppm
pH 7.2 7.4 - 7.6 7.8
Total Alkalinity 100 ppm 100 - 140 ppm 140 ppm
Calcium Hardness 150 ppm 200 - 400 ppm 500 - 1000 ppm
Stabilizer (Cyanuric Acid) 10 ppm 30 - 50 ppm 100 ppm
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 30
TTRROOUUBBLLEESSHHOOOOTTIINNGG GGUUIIDDEE
TROUBLESHOOTING GUIDE
• The motor is not plugged in.
• Switch is not turn on.
•The GFCI circuit breaker is
tripped.
• Motor too hot and overload
protection is shut off.
• Improper sanitizer or pH levels.
• Filter cartridge is dirty.
• Damaged cartridge.
• Excessively dirty pool.
• The strainer screen is
restricting the water flow.
• Clogged inlet or discharge.
• An air leak on the intake line.
• Scale or buildup on cartridge.
• Excessively dirty pool.
• Dirty filter cartridge.
• Low water level.
• Strainer screen plugged up.
• An air leak on the intake hose.
• An air lock inside the cartridge
chamber and motor chamber.
• Service light on.
• O-ring missing.
• Cover is not tight.
• Filter cartridge is dirty.
• Hose nuts are not well-fitted.
• There’s air trapped in the pump
housing and inlet hose.
• The inlet and outlet hoses
connection are reversed.
PROBLEM CAUSE SOLUTION
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN'T
PUMP WATER OR
FLOW IS VERY
SLOW
PUMP DOESN'T
WORK
TOP COVER
LEAKING
HOSE LEAKING
AIR LOCK
• Filter cord must be plugged into a 3
wire outlet that is protected by a Class
A Ground Fault Circuit Interrupter, or
RCD.
• Reset circuit breaker. If circuit breaker
trips repeatedly, your electrical system
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
• Let motor cool down.
• Adjust the sanitizer and pH level.
Consult your local swimming pool
supply stores.
• Clean or replace cartridge.
• Check the cartridge for holes. Replace
if damaged.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.
• Clear any obstructions in the intake
hose by discharging it inside pool wall.
• Tighten hose nuts, check hoses for
damage, check pool water level.
• Replace cartridge.
• Clean cartridge more often.
• Clean inside the plunger valve.
• Pull valve handle to full upright position.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose nuts, check hose for
damage.
• Clear any sticks or leaves in the intake
hose.
• Turn and pull valve handle to full upright
position.
• Unscrew two air release valve on the
chamber to fullfill water.
• Contact Intex Service Center.
• Remove cover & check for O-ring.
• Tighten cover (Manually).
• Replace or clean cartridge.
• Tighten or reinstall hose nut.
• Open air release valves, lift and lower
the inlet hose until water starts to flow
out of the valve, then close it.
• The lower position of pool outlet
connects to filter pump water inlet. The
upper position of pool inlet connects to
filter pump water outlet.
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 31
TTRROOUUBBLLEESSHHOOOOTTIINNGG GGUUIIDDEE
TROUBLESHOOTING GUIDE (continued)
INSUFFICIENT
CHLORINE
INSUFFICIENT
COPPER ION
LEVEL
POOL IS STAINED
WHITE FLAKES IN
THE WATER
NO LED DISPLAY
GREEN HAIR
•Insufficient operating hours of
the Saltwater System.
•The salt level in the pool water
is less than 2000ppm. This is
insufficient.
•Chlorine loss due to intense
sunlight exposure.
•The bather load has increased.
•Clogged or dirty electrolytic cell.
•Insufficient operating hours.
•The PH is too high.
•The bather load has increased.
•Clogged or dirty copper
electrode.
•Copper electrode defective.
•High copper ion concentration.
•Excessive calcium hardness is
present in pool water.
•No power supply.
• RCD/GFCI has not reseted.
•A power fuse has blown.
•LED failure.
• Incorrect switching, press two
buttons ( and ) together.
•High copper ion concentration.
•
Increase the daily Saltwater System
operating time. See “Operating Instructions”.
•
Check the salt level with the Test Kit. Adjust
as needed. See “Salt & Pool Water
Volumes”.
•
Use a pool cover when the pool is not in
use and/or when the unit is operating.
•
Increase the daily Saltwater System
operating time. See “Operating Instructions”.
•
Remove the cell for inspection, clean it if
necessary. See “Maintenance”.
•Increase operating time per day. See
“Operating Instructions”.
•Use PH decrease chemical to adjust,
contact your local pool chemical store.
•Increase the operating time per day.
See “Operating Instructions”.
•Remove the cell for inspection, clean it
if necessary. See “Maintenance”.
•Contact Intex Service Center.
•Drain about 20% of the pool water and
add fresh water to decrease the copper
ion concentration below 0.2ppm.
•Add aluminum sulfate: 1000 liters
water need around 2g (1000 gals need
0.27 ounce) or aluminum potassium
sulfate: 1000 liters water need around
3g (1000 gals need 0.4 ounce) to pool.
• Use a lemon based cleaning product
(preferably containing citric acid). Don’t
scrub with aggressive cleaning
products because this might etch the
underlying surface.
•Drain about 20 to 25% of the pool
water and add fresh water to decrease
the calcium hardness. Inspect the
electrolytic cell for scale buildup. Clean
the electrolytic cell if necessary.
•
Plug the cell cord firmly into the cell
housing receptacle.
•
Reset the RCD/GFCI.
•
Contact Intex Service Center.
•
Contact Intex Service Center.
•
Shut down and turn on the power again,
re-set the time. See “Operating Instructions”.
•Drain about 20% of the pool water and
add fresh water to decrease the copper
ion concentration below 0.2ppm.
•Add aluminum sulfate: 1000 liters
water need around 2g (1000 gals need
0.27 ounce) or aluminum potassium
sulfate: 1000 liters water need around
3g (1000 gals need 0.4 ounce) to pool.
• Use ‘Ultra-Swim’ shampoo, or shampoo
containing chelating agents.
PROBLEM CAUSE SOLUTION
IMPORTANT
If you continue to experience difficulty, please contact our Consumer
Service Department for assistance. See back cover for contact information.
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 32
TTRROOUUBBLLEESSHHOOOOTTIINNGG GGUUIIDDEE
TROUBLESHOOTING GUIDE (continued)
1. Circulation line is blocked.
2. Incorrect inlet and outlet hose
direction.
3. Incorrectly installed flow sensor
conduit.
4. Scale on the flow sensor.
5. Flow sensor cord is loose.
6. Inner timer confliction between
filter pump and saltwater system.
7. Flow sensor failure.
1. Dirt or scale on titanium plates.
2. Low salt level / No salt.
3. Electrolytic cell cord is loose.
4. Possible electrolytic cell failure.
1. High salt level.
1. Display and all lights are off - the
system does not power up.
•If your unit has plunger valves, ensure
that they are open.
•Clear your filter cartridge and cell from
debris and dirt. See “Maintenance”.
•Release all trapped air in the circulation
line. See the filter pump manual.
•Check the direction of the inlet and the
outlet hose. Reverse the hoses if
necessary. See “Set Up Instructions”.
•Check that the arrow on the flow sensor
conduit, points in the same direction as
the one on the cell. Reverse the flow
sensor conduit if necessary.
•Clean the flow sensor, paying special
attention to the hinge. See
“Maintenance”.
•Plug the flow sensor firmly into the flow
sensor receptacle.
•Reset both timers on the filter pump and
saltwater system.See “Boost Cycle”.
•Contact Intex Service Center.
•Remove the electrolytic cell for
inspection. Clean it if necessary.
See “Maintenance”.
•Add salt. See “Salt & Pool Water
Volumes”.
•Ensure that the cell cord is plugged
firmly into the cell housing receptacle.
•Contact Intex Service Center. Replace
the cell if needed.
•Partially drain the pool and refill it with
fresh water. See “Salt & Pool Water
Volumes”.
•Household voltage is too high or too low
(+ 20%). Check the voltage is within the
range stated on the device housing.
•Contact Intex Service Center.
LED PANEL
CODE PROBLEM SOLUTION
LED Panel Code Flash & Alarm On (NOTE: Always turn off the power before cleaning and servicing).
134A
SAVE THESE INSTRUCTIONS
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Page 33
SSAAFFEETTYY GGUUIIDDEELLIINNEESS
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and dangers.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demand constant supervision. A competent adult should be appointed as
a “lifeguard” or water watcher, especially when children are in and around
the pool.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is supervising pool users about potential pool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Instruct all pool users, including children what to do in case of an
emergency.
• Always use common sense and good judgement when enjoying any
water activity.
• Supervise, supervise, supervise.
134A
SAVE THESE INSTRUCTIONS Page 34
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
Your Krystal ClearTM Saltwater System has been manufactured using the highest
quality materials and workmanship. All Intex products have been inspected and
found free of defects prior to leaving the factory. This Limited Warranty applies only to
the Krystal ClearTM Saltwater System and accessories listed below.
The following provision is only valid within the European member states countries:
The legal regulation of Directive 1999/44/EC will not be effected by this Intex
warranty.
The provisions of this Limited Warranty apply only to the original purchaser and is
not transferable. This Limited Warranty is valid for the period noted below from the
date of the initial retail purchase. Keep your original sales receipt with this manual,
as proof of purchase will be required and must accompany warranty claims or the
Limited Warranty is invalid.
Krystal ClearTM Saltwater System Warranty – 2 Years
Hoses, Plunger Valves & Fittings Warranty – 180 days
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in this manual. The Service Center will
determine the validity of the claim.
IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND
IN NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR EMPLOYEES BE
LIABLE TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR
CONSEQUENTIAL DAMAGES OR LIABILITIES. Some countries, or jurisdictions do
not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
This Limited Warranty does not apply if the products are subject to negligence,
abnormal use or operation, accident, improper operation, improper voltage or current
contrary to operating instructions, or to damage by circumstances beyond Intex’s
control, including but not limited to, ordinary wear and tear and damage caused by
exposure to fire, flood, freezing, rain, or other external environmental forces. This
Limited Warranty applies only to those parts and components sold by Intex. The
Limited Warranty does not cover unauthorized alterations, repairs or disassembly by
anyone other than Intex Service Center personnel.
The costs associated with the loss of pool water, chemicals or water damage are not
covered by this warranty. Injury or damage to any property or person is not covered
by this warranty.
LIMITED WARRANTY
134A
SAVE THESE INSTRUCTIONS Page 35
(134) MODEL CS8221/CS8231 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/18/2011
English
For service questions or to order replacement parts, please contact the
appropriate office listed below or visit www.intexdevelopment.com for answers
to most frequently asked questions.
AREAS LOCATION AREAS LOCATION
• ARGENTINA JARSE INDUSTRIAL Y COMERCIAL S.A
MANUEL GARCIA 124 (CP1284)
CIUDAD AUTÓNOMA DE BUENOS AIRES,
ARGENTINA.
TEL: 011-4942-2238 (interno 139);
TEL: 011-4942-2238( interno 145)
E-mail: Martín Cosoleto: mcosoleto@jarse.com.ar
E-mail: Daniel Centurion: dcenturion@jarse.com.ar
Website: www.jarse.com.ar
• PERU COMEXA S.A.
AVENIDA COMANDANTE ESPINAR 142,
MIRAFLORES, LIMA, PERÚ
TEL: 446-9014
• SAUDI ARABIA SAUDI ARABIAN MARKETING &
AGENCIES CO. LTD.
PRINCE AMIR MAJED STREET,
AL-SAFA DISTRICT. JEDDAH,
KINGDOM OF SAUDI ARABIA
TEL: 966-2-693 8496
FAX: 966-2-271 4084
E-mail: toy@samaco.com.sa
Website: www.samaco.com.sa
• AUSTRIA STEINBACH VERTRIEBSGMBH
AISTINGERSTRAßE 2
4311 SCHWERTBERG
TEL: 0820 - 200 100 200
(0,145€/min aus allen Netzen)
FAX: + 43 (7262) 61439
E-mail: service@intexcorp.at
Website: www.intexcorp.at
• CZECH REPUBLIC / INTEX TRADING S.R.O.
EASTERN EUROPE BENESOVSKA 23,
101 00 PRAHA 10,
CZECH REPUBLIC
TEL: +420-267 313 188
FAX: +420-267 312 552
E-mail: info@intexcorp.cz
• BELGIUM N.V. SIMBA-DICKIE BELGIUM S.A.
MOESKROENSESTEENWEG 383C,
8511 AALBEKE, BELGIUM
TEL: 0800 92088
FAX: 32-56.26.05.38
E-mail: intex@nicotoy.be
E-mail: intexsupport@nicotoy.be
Website: www.nicotoy.be/downloads.htm
• DENMARK K.E. MATHIASEN A/S
SINTRUPVEJ 12, DK-8220
BRABRAND, DENMARK
TEL: +45 89 44 22 00
FAX: +45 86 24 02 39
E-mail: intex@keleg.dk
Website: www.intexnordic.com
• SWEDEN LEKSAM AB
BRANDSVIGSGATAN 6,
S-262 73 ÄNGELHOLM,
SWEDEN
TEL: +46 431 44 41 00
FAX: +46 431 190 35
E-mail: intex@leksam.se
Website: www.intexnordic.com
• NORWAY NORSTAR AS
PINDSLEVEIEN 1,
N-3221 SANDEFJORD,
NORWAY
TEL: +47 33 48 74 10
FAX: +47 33 48 74 11
E-mail: intex@norstar.no
Website: www.intexnordic.com
• FINLAND NORSTAR OY
SUOMALAISTENTIE 7,
FIN-02270 ESPOO,
FINLAND
TEL: +358 9 8190 530
FAX: +358 9 8190 5335
E-mail: info@norstar.fi
Website: www.intexnordic.com
• RUSSIA LLC BAUER
KIEVSKAYA STR., 20,
121165 MOSCOW, RUSSIA
TEL: 099-249-9400/8626/9802
FAX: 095-742-8192
E-mail: intex.russia@gmail.com
Website: www.intex.su
• POLAND KATHAY HASTER
UL. LUTYCKA 3, 60-415 POZNAN
TEL: +48 61 8498 334
FAX: +48 61 8474 487
E-mail: inx@kathay.com.pl
Website: www.intexdevelopment.pl
• HUNGARY RECONTRA LTD./RICKI LTD.
H-1113 BUDAPEST, DARÓCZI ÚT 1-3,
HUNGARY
TEL: +361 372 5200/113
FAX: +361 209 2634
E-mail: service@recontra.hu
• BRASIL KONESUL MARKETING & SALES LTDA
RUA ANTONIO DAS CHAGAS,
1.528 - CEP. 04714-002,
CHÁCARA SANTO ANTONIO - SÃO
PAULO - SP - BRASIL
TEL: 55 (11) 5181 4646
FAX: 55 (11) 5181 4646
E-mail: sacintexbrasil@uol.com.br
• ISRAEL ALFIT TOYS LTD
MOSHAV NEHALIM,
MESHEK 32, 49950, ISRAEL
TEL: +972-3-9076666
FAX: +972-3-9076660
E-mail: michald@chagim.co.il
• ASIA INTEX DEVELOPMENT CO. LTD.
9TH FLOOR,
DAH SING FINANCIAL CENTRE,
108 GLOUCESTER ROAD,
WANCHAI, HONG KONG
TEL: 852-28270000
FAX: 852-23118200
E-mail: xmservicesupport@intexcorp.com.cn
Website: www.intexdevelopment.com
•EUROPE INTEX TRADING B.V.
POSTBUS 1075, 4700 BB ROOSENDAAL,
THE NETHERLANDS
TEL: 31-(0)165-593939
FAX: 31-(0)165-593969
E-mail: service@intexcorp.nl
Website: www.intexcorp.nl
• FRANCE UNITEX / INTEX SERVICE FRANCE S.A.S
Z.A. DE MILLEURE
BOIS DU BAN - N°4
71480 LE MIROIR
TEL: 08 90 71 20 39 (0,15€/min)
FAX: 03 84 25 18 09
Website: www.intex.fr
•GERMANY STEINBACH VERTRIEBSGMBH
C/O WEBOPAC LOGISTICS GMBH
INTER-LOGISTIK-PARK 1-3
87600 KAUFBEUREN
TEL: 0180 5 405 100 200
(0,14€/min aus dem Festnetz, Mobilfunk max. 0,42€/min)
FAX: + 43 (7262) 61439
E-mail: service@intexcorp.de
Website: www.intexcorp.de
• ITALY A & A MARKETING SERVICE
VIA RAFFAELLO SANZIO 19
20852 VILLASANTA (MB)
TEL: 199 12 19 78
FAX: +39 039 2058204
E-mail: info@intexitalia.com
Website: www.intexitalia.com
• UK JOHN ADAMS LEISURE LTD
MARKETING HOUSE,
BLACKSTONE ROAD,
HUNTINGDON, CAMBS.
PE29 6EF. UK
TEL: 0844 561 7129
FAX: 01480 414761
E-mail: sales@johnadams.co.uk
Website: www.intexspares.com
•SWITZERLAND GWM AGENCY
GARTEN-U. WOHNMÖBEL,
RÄFFELSTRASSE 25,
POSTFACH,
CH-8045 ZURICH/SWITZERLAND
TEL: 0900 455456 or +41 44 455 50 60
FAX: +41 44 455 50 65
E-mail: gwm@gwm.ch
Website: www.gwm.ch, www.gwmsale.ch
• SPAIN / PORTUGAL Nostrum Iberian Market S.A.
Av. de la Albufera, 321
28031 Madrid, Spain
TEL: +34 902101339
FAX for Spain: +34 9 029 089 76
Email for Spain: sat@intexiberian.com
FAX for Portugal: +351 707 506 090
Email for Portugal: spv-pt@intexiberian.com
Website: www.intexiberian.com
• AUSTRALIA HUNTER PRODUCTS PTY LTD
LEVEL 1, 225 BAY STREET,
BRIGHTON, VICTORIA,
AUSTRALIA
TEL: 61-3-9596-2144 or 1800-224-094
FAX: 61-3-9596-2188
E-mail: enquiries@hunteroverseas.com.au
Website: www.hunterproducts.com.au
• NEW ZEALAND HAKA NEW ZEALAND LIMITED
UNIT 4, 11 ORBIT DIVE, ALBANY,
AUCKLAND 0757, NEW ZEALAND
TEL: 649-4159213 / 0800 634434
FAX: 649-4159212
E-mail: geoff@hakanz.co.nz
Website: www.hakanz.co.nz
• MIDDLE EAST FIRST GROUP INTERNATIONAL
REGION AL MOOSA GROUP BUILDING, 1ST
FLOOR, OFFICE 102 & 103, UMM HURAIR
ROAD, KARAMA, DUBAI, UAE
TEL: 00971-4-800INTEX(46839) / +971-4-3373322
FAX: 00971-4-3375115
E-mail: intex@firstgroupinternational.com.
Website: www.firstgroupinternational.com
• SOUTH AFRICA WOOD & HYDE
15-17 PACKER AVENUE, INDUSTRIA 2,
CAPE TOWN, SOUTH AFRICA 7460
TEL: 0-800-204-692 (Toll Free) or 27-21-505-5500
FAX: 27-21-505-5600
E-mail: ygoldman@melbro.co.za
• CHILE / URUGUAY COMEXA S.A.
EL JUNCAL 100, PARQUE INDUSTRIAL
PORTEZUELO, QUILICURA, SANTIAGO, CHILE.
TEL: 600-822-0700
E-mail: serviciotecnico@silfa.cl
1 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex CS8221 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex CS8221 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Intex CS8221

Intex CS8221 Gebruiksaanwijzing - Deutsch - 35 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info