522371
49
Verklein
Vergroot
Pagina terug
1/89
Pagina verder
51
User Manual
5. C-LINK
5.1 C-LINK
C-Link system is a feature which allows to sharing the same cartographic data
between two chart plotter units (CP) linked via serial I/O port.
In order to activate C-Link function, a “MAX data C-CARD” (called REGULAR C-
CARD) must be inserted into one of the two chart plotters and a special MAX data
C-CARD (called MIRROR C-CARD) must be inserted on the other chart plotter.
The two MAX data C-CARDs must have the same code and revision. So, the
MIRROR C-CARD can be utilized only on a chart plotter linked to another chart
plotter provided with the equivalent REGULAR C-CARD.
It is important to point out that the two chart plotters must have the update s/w
versions that allow C-Link function.
How C-Link system works
When the CP is powered up, it switches into the “Stand-Alone Mode”. In this work
mode, the CP unit periodically scans all the available C-CARD slots searching for
MIRROR C-CARDs.
When one or more MIRROR C-CARD is found (in one or both CPs) a special con-
nection is established between the CPs to habilitate the MIRROR C-CARDs.
If a regular C-CARD which has previously activated a MIRROR C-CARD is re-
moved, even the MIRROR card will be not read anymore on the other unit.
C-Link serial connection
The two chart plotters should be connected via serial ports. Any of the available
ports can be used, the software will recognize automatically the serial ports used.
A typical connection is as follows:
CP1 CP2
TX —————> RX
RX <————— TX
GND <————> GND
NOTE If the serial port used for the connection is Port 1 (optoisolated) do not forget
to connect the "Input 1-" signal (Green Wire) to the GND wire.
5.2 C-LINK NAVIGATION DATA TRANSFER
This function allows transferring C-Link navigation data (Route Name, Destination
ID & Position, Next Waypoint ID & Position, Total Route length, Fuel Consumption
Rate, ETA, TTG etc.) (Hereinafter “C-Link navigation data”) between two chart
plotters linked through the C-Link system.
The chart plotters can be set to operate in two modes:
- MASTER mode (Primary Chart Plotter)
- SLAVE mode (Secondary Chart Plotter)
When the navigation is activated on the Master chart plotter, the C-Link naviga-
tion data will be continuously sent to the Slave until the navigation is active.
If the Master is navigating to a Single Destination, the Slave will show the Desti-
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Interphase CHART MASTER 11 CV plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Interphase CHART MASTER 11 CV plus in de taal/talen: Engels als bijlage per email.

De handleiding is 5,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info