557903

Intermatic EJ500 Handleiding

2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Press HOUR+ to set the hour you want the program to turn ON.
Press M+ to set the minutes you want the
program to turn ON (Fig. 14).
Press NEXT ON/OFF to set the OFF time for the
program. The screen again displays blanks
(Fig. 15).
Press DAY/DST as many times as necessary to
display 12:00 a.m. and the day(s) you want
the program to activate (Fig. 16).
NOTE: Since you’re setting an OFF time for an
ON event already programmed, choose the
same days as in the ON event.
Press HOUR+ to set the hour you want the program to turn
OFF.
Press M+ to set the minutes you want the
program to turn OFF (Fig. 17).
At this point you have two choices:
Press MODE if you are finished to exit from programming.
Press NEXT ON/OFF to set another program. Repeat from
Step 2 above.
1.
2.
4.
1.
1.
2.
4.
-
-
As you press the buttons to program, it will be helpful to have
an overview of how they are organized. Press the MODE button
to rotate through the switch timer’s modes: CALendar, CLocK,
ProGraM, AUTO, AUTORANDom, and MANual.
Within each mode, menus “loop”, so they repeat when you
get to the end.
You must set the CALendar and CLocK before programming
ON/OFF times.
If you’re interrupted during programming, your work to that
point is automatically saved after 5 minutes.
•
•
•
•
3 – Intro to Programming: Read Before You Begin
5 – Set the Date and Time
Fig. 8
Fig. 7
South
North
Center
North
Center
South
It’s unlikely that the new switch timer has any existing program-
ming but to make sure, use this procedure before setting the time.
Open the front cover.
Press the RESET button while holding down the NEXT ON/OFF
button.
Release the RESET button. The screen will initialize, then flash
“12:00 am” in MANual mode.
Release the NEXT ON/OFF button.
All previous settings are now deleted.
1.
2.
3.
4.
4 – Clear Any Existing Programming
Press NEXT ON/OFF to display the date. The
word DATE and a number will be flashing
(Fig. 2).
Press M+ to stop the flashing. Press again as
necessary to display the correct month (Fig. 3).
Press DAY/DST as necessary to display the cor-
rect date (Fig. 3). The correct day of the week
is shown as well.
Press NEXT ON/OFF to set Daylight Saving Time
(DST). The display flashes between DST and
AUTO (Fig. 4).
Press DAY/DST to stop the flashing. Press again
to toggle between AUTO and MAN for wheth-
er you want to adjust automatically for DST.
If your area uses DST, select AUTO (Fig. 5).
If your area does not use DST, select MAN.
Press NEXT ON/OFF to to set your ZONE. The
display flashes between ZONE and CENTr
(Fig. 6). This feature tracks changes in sunrise
and sunset times.
Press ZONE+ to stop the flash-
ing. Press again to toggle
between SOUTh, NORTh,
and CENTr. Use the map (Fig.
7) to determine your zone.
Press NEXT ON/OFF to set exact
sunup and sunset times. The
display flashes between SUNUp and an AM
time (Fig. 8). Find the exact times in your area
in your newspaper or online.
If you DO NOT want to set exact Sunup and Sunset times:
Press NEXT ON/OFF to advance to SNSEt.
If you DO want to set exact Sunup and Sunset times:
Press HOUR+ as necessary to set the cor-
rect SUNUp hour (Fig. 9).
NOTE: The small letter “d” tells you that
Daylight Saving Time is in effect.
Press M+ as necessary to set the correct minute.
Press NEXT ON/OFF to advance to setting exact SNSEt time
(Fig. 10).
Press HOUR+ as necessary to set the cor-
rect SNSEt hour.
Press M+ as necessary to set the correct SNSEt minute.
Setting the Calendar is complete. Now set Time of Day.
Press MODE to display CLK (clock) and a time.
The first time, 12:00 am will flash (Fig. 11).
Press HOUR+ to stop the flashing.
Press HOUR+ and M+ to set the correct time.
NOTE: Make sure AM or PM is correct.
Time and Date are now set. You can program ON/OFF settings.
3.
1.
2.
3.
6.
-
-
7.
6.
7.
-
a.
-
a.
a.
b.
c.
d.
1.
2.
3.
The two LR44/SR44 alkaline batteries maintain calendar and
time settings during power interruptions for up to 3 months
of accumulated interruptions. All other settings remain in
memory indefinitely without batteries or AC power.
Remove batteries if the switch timer will be without AC power
for an extended time.
Replace the batteries if the display is dim or displays “lobAT”.
Batteries may be changed without removing AC power.
If AC power is removed, swap batteries within 15 seconds to
avoid losing time-of-day and calendar settings.
Remove the battery holder by prying left and right of the holder
with the tip of a flat screwdriver, then pry the battery holder up.
Install new batteries in the battery holder as marked, then
place it back into the switch timer with notch down.
If the display flashes “12:00,” reset time and check the date.
•
•
•
•
•
•
•
•
About the Battery
Once set up, you have three choices for using the switch timer.
To make a selection, open the front cover and press the MODE
button until you see your choice of the following options:
AUTO — uses the timer settings you have programmed.
AUTO RANDom — gives your home a “lived-in” look by vary-
ing your settings by a random amount of ± 20 minutes or so.
MANual — maintains your settings but operates the switch
timer like a standard ON/OFF. Press on the door of the switch
timer for ON, press again for OFF.
•
•
•
7 – Selecting AUTO, AUTO RANDom, or MANual Operation
Wiring Diagrams for Multiple Switch Timer Setups:
For a two-switch setup (3-way) when reusing the existing 3-way
remote switch:
NOTE: For new construction or to replace a dimmer switch, a
lighted switch, or a 3-way switch without screw terminals, a
single-pole switch can be used at the remote location, as shown
below.
For a two-switch setup (3-way) using single-pole remote switch:
For a three-switch setup:
For four or more switch setups:
Use the preceding 3-switch installation diagram and wire 4-way
switches between the two 3-way switches.
LINE
BLACK
TIMER
BLUE
RED
JUMPER
LOAD
NEUTRAL
COMMON
3-WAY SWITCH
LINE
BLACK
TIMER
BLUE
RED
JUMPER
LOAD
NEUTRAL
COMMON
3-WAY SWITCH
BLACK
BLUE
LOAD
NEUTRAL
RED
TIMER
LINE
SINGLE-POLE SWITCH
BLACK
BLUE
LOAD
NEUTRAL
RED
TIMER
LINE
SINGLE-POLE SWITCH
6b – Set an ON/OFF Program for Sunrise/Sunset
Press MODE until the screen displays PGM
with blanks for time (Fig. 18).
Press DAY/DST as many times as necessary to
display 12:00 a.m. and the day(s) you want
the program to activate. Choices are:
everyday
weekdays only (Fig. 19)
weekends only
a specific day
NOTE: If you go too far, keep pressing DAY/DST to loop back
around again.
Press HOUR+ to select SNST (sunset) or SNUP
(sunup) for turning the program ON (Fig. 20).
Press NEXT ON/OFF to set the OFF time for the
program. The screen again displays blanks
(Fig. 21).
Press DAY/DST as many times as necessary to
display 12:00 a.m. and the day(s) you want
the program to activate (Fig. 22).
NOTE: Since you’re setting an OFF time for an
ON event already programmed, choose the
same days as in the ON event.
Press HOUR+ to select SNST (sunset) or SNUP
(sunup) for turning the program OFF (Fig. 23).
At this point you have two choices:
Press MODE if you are finished to exit from programming.
Press NEXT ON/OFF to set another program. Repeat from
Step 2 above.
1.
2.
-
-
-
-
1.
4.
1.
1.
4.
-
-
NOTE: If you go too far, keep pressing DAY/DST to loop back
around again.
Press HOUR+ to select SNST (sunset) for turning
the program ON (Fig. 26).
Press NEXT ON/OFF to set the OFF time for the
program. The screen again displays blanks
(Fig. 27).
Press DAY/DST as many times as necessary to
display 12:00 a.m. and the day(s) you want the
program to activate (Fig. 28).
NOTE: Since you’re setting an OFF time for an
ON event already programmed, choose the same days as in
the ON event.
Press HOUR+ to set the hour you want the program to turn
OFF.
Press M+ to set the minutes you want the
program to turn OFF (Fig. 29).
At this point you have two choices:
Press MODE if you are finished to exit from programming.
Press NEXT ON/OFF to set another program. Repeat from
Step 2 above.
1.
4.
1.
1.
2.
4.
-
-
To override a program (ON/OFF time) till its next schedules time:
Press on the control cover (over the programming buttons)
Open the control cover and press the NEXT ON/OFF button.
•
•
Manual Override
In order for the switch timer to automatically adjust for seasonal
changes in sunrise and sunset, and change back and forth to
Daylight Saving Time, the CALENDAR must be set correctly.
NOTE: If you go too far, keep pressing the button to loop back
around. For Year and Hour, you can also press the YEAR- / HOUR-
button to back up.
Press MODE to display CAL and the year. The first time, the
word YEAR and a number will flash (Fig. 1).
Press YEAR+ to stop the flashing. Press again
as necessary to display the correct year.
1.
2.
6a – Set an ON/OFF Program at Specific Times
Press MODE until the screen displays PGM
with blanks for time (Fig. 12).
Press DAY/DST as many times as necessary to
display 12:00 a.m. and the day(s) you want
the program to activate. Choices are:
everyday
weekdays only (Fig. 13)
weekends only
a specific day
NOTE: If you go too far, keep pressing DAY/DST to loop back
around again.
1.
2.
-
-
-
-
6c – Setting Sunset ON/Specific Time OFF
Sunset ON / Specic Time OFF is the most common setting for the
switch timer. As a convenience, here is the full step-by-step.
Press MODE until the screen displays PGM
with blanks for time (Fig. 24).
Press DAY/DST as many times as necessary to
display 12:00 a.m. and the day(s) you want
the program to activate. Choices are:
everyday
weekdays only (Fig. 25)
weekends only
a specific day
1.
2.
-
-
-
-
The manual “air gap” switch at he top
edge of the switch timer is designed to turn
power off for routine maintenance (e.g.,
repairs, removing broken bulbs, etc.). Using
this switch for normal ON/OFF operation
will shorten battery life.
The “Air Gap” Switch
ON
OFF
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intermatic EJ500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intermatic EJ500 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info