738437
33
Verklein
Vergroot
Pagina terug
1/33
Pagina verder
TABLE OF CONTENTS
BEFORE YOU BEGIN 1
IMPORTANT SAFETY NOTICE 2
CONTENTS OF PACKAGING 3
LABEL PLACEMENT 4
HARDWARE PACK 5
ASSEMBLY INSTRUCTIONS 6-15
PRODUCT FEATURES 16-17
COMPUTER OPERATION GUIDELINE 18-22
PARTS LIST 23-25
ALTERNATE PLUG PART NUMBERS 26
EXPLODED DIAGRAMS 27-29
WARRANTY 30-31
BEFORE YOU BEGIN
Thank you for selecting the INSPIRE CS2 CARDIOSTRIDER. For your safety and
benefit, read this manual carefully before using the machine. As a manufacturer, we are
committed to providing you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance to you.
1
HEALTH IN MOTION, LLC.
255 AIRPORT CIRCLE, SUITE 101
CORONA, CA 92880
Toll-Free Customer Service Number
1-877-738-1729
Mon. - Fri. 8 a.m. - 5 p.m. PST
www.inspirefitness.com
PRECAUTIONS
IMPORTANT SAFETY NOTICE
This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a
piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine.
In particular, note the following safety precautions:
Keep children and pets away from the machine at all times. DO NOT leave
children unattended in the same room with the machine. The linkages on
this machine can cause serious injury or death if used improperly.
Engage Child Safety Lock, detailed in this manual, after each use.
Never place your hands or feet in the path of the linkages because injury may
occur to you or damage may occur to the equipment. Never allow children to
come near or approach the moving linkages while in use.
If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
Position the machine on a clear, leveled surface.
DO NOT use the machine near water or outdoors.
Keep hands away from all moving parts.
Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running or
aerobic shoes are also required when using the machine.
Use the machine only for its intended use as described in this manual. DO NOT
use attachments not recommended by the manufacturer.
Do not place any sharp object around the machine.
Disabled persons should not use the machine without a qualified person or
physician in attendance.
Before using the machine to exercise, always do stretching exercises to properly
warm up.
Never operate the machine if the machine is not functioning properly.
Maximum user weight 300 lbs.
Allow 24” (61 cm) of space on each side of the unit. Never place body parts
under pivot area (directly behind pedal).
Ensure that all pull pins, locks, and safety latches are fully engaged before use.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. NEITHER HEALTH IN
MOTION, LLC. NOR FG1, LLC. ASSUMES ANY RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS
PRODUCT.
2
CARE AND MAINTENANCE
1. Keep seat slider clean
2. Inspect and tighten all parts before using the machine.
3. The Frame and Seat Pad of the machine can be cleaned using a damp cloth and mild
non-abrasive detergent. DO NOT USE SOLVENTS.
CONTENTS OF PACKAGING
3
WARNING/PATENT LABEL PLACEMENT
The warning and patent labels have been placed on the unit in location shown. If the labels are missing or
illegible, please call customer service at 1-877-738-1729 for replacements. Apply the labels in location
shown.
4
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
5
STEP 1: FRAME STABILIZER ASSEMBLY (See Step 1 Figure)
Installing Stabilizers
A.) Carefully unpack contents of box leaving the 3 large styrofoam frame support blocks
in place.
B.) Remove large styrofoam support from REAR portion of frame.
The Rear Stabilizer mounting bracket should now be exposed.
C.) Place (#28) Rear Stabilizer underneath the Rear Mounting Bracket.
Ensure that the transport wheels are facing away from the unit.
D.) Attach the (#28) Rear Stabilizer to the frame as shown in FIGURE 1 with:
2 x (#27) M8x 70 Carriage Bolts 2x (#29) Curved Washers
2 x (#30) Acorn Nuts
E.) Remove large styrofoam support from FRONT portion of frame.
The Front Stabilizer mounting bracket should now be exposed.
F.) Place (#62) Front Stabilizer underneath the Front Mounting Bracket.
G.) Attach (#62) Front Stabilizer to the frame as shown in FIGURE 1 with:
2 x (#27) M8x 70 Carriage Bolts 2x (#29) Curved Washers
1 x (#30) Acorn Nuts 1x (#36) Child Safety Lock
NOTE:
(#36) Child Safety Lock is used instead of a
nut on USER left side of the Front Stabilizer.
Required Hardware: STEP 1
4x (#27) M8x 70 Carriage Bolts
3x (#30) Acorn Nut
4x (#29) Curved Washer
1x (#36) Child Safety Lock
Required Parts:
(#28) Rear Stabilizer Tube
(#62) Front Stabilizer Tube
STEP 2: SWING ARM ASSEMBLY (See Step 2 Figure)
A.) Slide (#47) Swing Arm Assembly R over the pivot shaft of main frame,
as shown in Step 2. NOTE: Lift spacer between bearings to allow insertion.
B.) Secure using:
1x (#20) Aluminum End Cap 1x (#26) Flat Head Socket Screw
As seen in Step 2 Figure
C.) Place the (#47) Swing Arm Assembly R on top of a styrofoam support block, so
the swing arm doesn’t touch the floor.
D.) Slide the (#85) Pedal Arm that is already attached to unit, into the (#47) Swing
Arm Assembly R
E.) Secure using:
6x (#29) Curved Washers 6x (#31) M8 * 17 Hex Screw
6x (# 32) Spring Washer
As seen in Step 2 Figure
F.) Slide (#54) Swing Arm Assembly L over the pivot shaft of main frame as shown in Figure 2.
G.) Secure using:
1x (#20) Aluminum End Cap 1x (#26) Flat Head Socket Screw
As seen in Figure 2
H.) Place the (#54) Swing Arm Assembly L on top of the styrofoam support block
with the red dot, so the swing arm doesn’t touch the floor.
I.) Slide the (#85) Pedal Arm that is already attached to unit, into the (#54) Swing
Arm Assembly L
J.) Secure using:
6x (#29) Curved Washers 6x (#31) M8 * 17 Hex Screw
6x (# 32) Spring Washer
Required Hardware: STEP 2
2x
12x
12x
(#20) Aluminum End Cap
(#29) Curved Washer
(#32) Spring Washer
2x (#26) Flat Head Socket Screw
12x (#31) M8 * 17 Hex Screw
Required Parts
(#47) Swing Arm Assembly R
(#54) Swing Arm Assembly L
HANDLE ASSEMBLY (See Step 2 Figure)
A) Loosen handle adjustment knob 2-3 turns. This will allow the arm to slide in.
B.) Slide the Right Handle Assembly (#21) into the (#47) Swing Arm Assembly R.
Adjust to desired position and tighten.
WARNING: Check to make sure the Right Handle Assembly has an “R” Sticker on
it. Accidental switching of the Right and Left Handle Assemblies can result in
serious injury.
C.) Loosen handle adjustment knob 2-3 turns. This will allow the arm to slide in.
D.) Slide the Left Handle Assembly (#42) into the Left Swing Arm Sleeve (#54). Adjust to
desired position and tighten.
WARNING: Check to make sure the Left Handle Assembly has an “L” Sticker on it.
Accidental switching of the Right and Left Handle Assemblies can result in serious
injury.
STEP 3: ASSEMBLING THE SEAT BACK & SEAT (See FIGURE 3)
Required Hardware: Step 3
1x (# 86) Hex Bolt 5x (#33) Flat Washer
1x (#24) Lock Nut 4x (#31) M8 * 17 Hex Screw
4x (#32) Spring Washers
Required Parts:
(# 50) Seat Back Assembly (#35) Seat Pad, Charcoal
Installing Seat Back Assembly
A.) Assemble Seatback Assembly (#50) onto Seat Slider Assembly.
Align lower hole and secure using:
1x (#24) Lock Nut 1x (#33) Flat Washer
1x (#86) Hex Bolt
Installing Seat
B.) Secure (#35) Seat to Seat Slider Assembly using:
4x (#31) M8 * 17 Hex Screw 4x (#33) Flat Washer
4x (#32) Spring Washers
STEP 4: MAST ASSEMBLY (See STEP 4)
Attaching the Mast
A.) Locate the ends of the included cable that should be sticking out of the top and
bottom of the (#39) Console Mast, labeled (#37) as seen in Step 4 Figure.
B.) Orient the bottom end of (#39) Console Mast near the top of the opening of the
Main Frame.
C.) Connect cable end of (#37) to the input connector (#83) that is inside the frame,
as seen in Step 4 Figure.
D.) Slide (#39) Console Mast onto the Main Frame.
NOTE: Make sure not to pinch the cable assembly when attaching the
console onto the mounting bracket.
E.) Secure both assemblies by using:
2x (#29) Curved Washers 4x (#33) Flat Washers
6x (#31) M8 * 17 Hex Screw
As seen in Step 4 Figure
Note (#29) Curved Washer in only used on the curved front of the mast.
Attaching the Bottle Holder
F.) Locate the two threaded holes along the inside of the mast
G.) Attach (#70) Bottle Holder onto the mast using:
2x (#49) M5 * 10 Phillips Head Screw
H.) Slide (#9) Water Bottle into the water bottle holder.
Required Hardware: STEP 5
2x
6x
(#29) Curved Washers
(#31) M8 * 16 Allen Head Screw
4x (#33) Flat Washers
2x (#49) M5 * 10 Phillips Head Screw
Required Parts:
(#39) Console Mast
(#19) Console
(#70) Bottle Holder
Attaching the Console
I.) Located, on the backside of (#19) Console,
will be 4x (#17) Phillips Head Screws threaded into four corners of the console.
J.) Remove the four screws, these will be used to mount the console onto the
console mount.
K.) Orient the console near the top of the mast ;
Connect cable ends Ato the cables coming from the frame
L.) Tuck cable away neatly inside the mast to avoid pinching, then mount the
console onto the mounting plate.
M.)Secure the console using the four screws removed in Step I.
FINAL STEPS
Level the unit by unscrewing the leveler feet
under (#62) Front Stabilizer so that both sit flat
on the ground.
Unscrew center leveler (located under the
center point of the unit) so that it touches the
ground. Failure to do so could cause damage to
your unit.
PRODUCT FEATURES
Handle Orientation
INVERTED HANDLES: Place handles in
inverted position.
This will focus on your biceps and triceps
muscles.
UPRIGHT HANDLES: Place handles in
upright position.
This will focus on your chest and back
muscles.
Seat Back Orientation
Choose a preferred
Seatback Recline Angle.
The seatback (#8) may be adjusted in
3 different Recline Angles
(UPPER, MIDDLE, LOWER)
Based on the users’ preferred position.
Align upper seatback tube hole with
preferred hole based on the below
figure.
Secure using the pin (b) as shown in to
the left.
ENGAGING THE CHILD SAFETY LOCK ASSEMBLY
1. ALWAYS engage the CHILD
SAFETY LOCK ASSEMBLY after
each use by clipping the hook onto
the loop located UNDERNEATH
the LEFT PEDAL ASSEMBLY.
(see FIGURE B below).
2. Before each workout, disengage
the hook from the loop. The
CHILD SAFETY LOCK
ASSEMBLY can hang freely
during your workout and will not
interfere with the mechanism.
CS2 COMPUTER OPERATION AND FEATURES
BASIC OPERATION
Press QUICK START to immediately begin workout in Manual Mode.
Press the STOP/RESET key at any time to PAUSE the workout. Press ENTER to
resume exercise. (Press STOP/RESET twice to reset program).
Press and hold the STOP/RESET key for 2 seconds to RESET the computer.
RESISTANCE: Press the UP or DOWN key to change the Resistance Level during
a workout. The Resistance may be adjusted from LEVEL 1 (Lowest) to LEVEL 20
(Highest). The Resistance level is displayed in the top center of the LCD.
VIEWING WORKOUT DATA: During a workout RPM and CALORIES are displayed
on the scrolling text bar. Press the “VIEW” button to display WATTS and DISTANCE.
Press and hold the “VIEW” buttons for 2 seconds to toggle on/off Autoscan (the
computer will switch between RPM/CALORIES and WATTS/DISTANCE every 10
seconds).
English/Metric Units: This computer uses a default of English Units of measurements.
To toggle between English / Metric Units:
-Press and hold RESET for 2 seconds to reset the computer
-While computer is rebooting, immediately press and hold the ENTER and VIEW
button at the same time
-Press UP and DOWN to toggle between Km and MILE. Press ENTER to accept
setting and reset the computer.
STANDARD PROGRAMS:
The CS2 CardioStrider has 6 Standard workout programs that will automatically adjust
the resistance.
At startup, press PROGRAMS. Press UP or DOWN to scroll through the
PROGRAMS.
20
o ROLLING HILL
o PEAK
o PLATEAU
o MOUNTAIN CLIMB
o HILL INTERVAL
o STRENGTH INTERVAL
After selecting your program press ENTER
LEVEL: Press UP or DOWN to set maximum resistance level. The resistance will
not go above this level during the workout. You may adjust the maximum resistance
during your workout. Press ENTER to accept maximum resistance level. Press
STOP/RESET to go back to PROGRAM selection.
WORKOUT TIME: Press UP or DOWN to set total workout time. Press ENTER to
accept workout time and begin. Press STOP/RESET to go back to LEVEL.
NOTE: The WORKOUT TIME may be changed during a workout by pressing the
“TIME +/- key. Press UP/DOWN to modify the WORKOUT TIME. Press
ENTER to begin workout.
21
FOCUS PROGRAMS:
The CS2 CardioStrider has 2 programs to focus workout on your upper body (Upper
Body Focus, Arms Focus). During the workout, the computer will beep and a scrolling
message will give you instructions.
A list of messages and their definitions are described below:
FEET ON PEDALS: Place feet on the moving pedals.
FEET ON PEGS: Place feet on the pegs. Round tube located at the front of the
unit.
PALMS UP: Place handles in INVERTED MODE. In INVERTED MODE, keep
palms facing upward to focus workout on the biceps muscle.
PALMS DOWN: Place handles in INVERTED MODE. In INVERTED MODE,
keep palms facing downward to focus workout on the triceps muscle.
22
FOCUS PROGRAM SETUP:
Press PROGRAMS. Press UP or DOWN to scroll through the PROGRAMS.
o UPPER BODY FOCUS: Focusing on upper body workout, including the
chest, back and arms. Also includes lower body workout.
o ARMS FOCUS: Focusing on upper body workout only. Feet remain on pegs.
After selecting your FOCUS program press ENTER
LEVEL: Press UP or DOWN to set maximum resistance level. This resistance will
not go above this level during the workout. You may adjust the maximum resistance
during your workout. Press ENTER to accept maximum resistance level. Press
STOP/RESET to go back to PROGRAM selection.
WORKOUT TIME: Press UP or DOWN to set total workout time. Press ENTER to
accept workout time and begin workout. Press STOP/RESET to go back to LEVEL.
23
PARTS LIST
EXP
NO.
EVS CODE
Description
Qty/Item
1
RC803-360-001
Back Pad Tube Assembly
1
2
CN-S24-000
EMS Flywheel
1
3
RC800-801-008A
Front Shroud R
1
4
0110-006-12
Hex Nut
2
5
RC803-601-001
Grip Shifter Tension Wire
1
6
0114-742-068
Cross Head Tap Bolt
6
7
RC804-801-001
Shroud L
1
8
RC803-401-002SK
Pad
1
9
BC830-881-006Q
Water Bottle
1
10
RC800-391-013
Ring Wire Pop pin φ8*63
1
11
0116-306-02
Spring Washer φ6
2
12
0113-208-358A
Allen Head Bolt M8*35
1
13
RC800-801-014
Pedal Arm
2
14
0110-410-019
Hex Flange Nut M10*1
2
15
0113-104-108
Cross Head Bolt M4*10
20
16
BC12-011-72
Tension Bolt M6
2
17
RC802-630-002SK
Phillips Head Screw M5*10
4
18
0114-142-198
Phillips Head Screw ST4.2*19
7
19
RC803-630-001A
Console
1
20
RC804-561-017
Aluminum End Cap φ50*6
2
21
RC801-331-002
Right Handle Assembly
1
22
0113-106-018
Cross Head Bolt M6*10
2
23
BC680-801-010B
End Cap 2
2
24
0110-808-008
Lock Nut M8
1
25
0113-306-165
Inner Hex Socket Bolt M6*16
2
24
26
0113-308-206
Flat Head Socket Screw M8*20
2
27
0111-408-718
M8*70 Carriage Bolt
4
28
RC800-341-002PZ
Rear Stabilizer Tube
1
29
0116-608-008
Curved Washer
18
30
0110-308-008
Acorn Nut
4
31
0113-008-168
M8 * 17 Hex Screw
30
32
0116-308-010
Spring Washer φ8
28
33
0116-008-010
Flat Washer φ8
18
34
RC803-200-001
Main Frame Assembly
1
35
RC803-401-001SK
Seat Pad Assembly
1
36
RC800-561-005
Child Safety Lock
1
37
RC803-630-001B
Console Upper Wire
1
38
RC804-801-002
Shroud R
1
39
RC803-350-001
Console Mast
1
40
RC800-221-002
Five-way Tube
1
41
0200-310-532
Ball Bearing 6004ZZ
2
42
RC801-331-001
Left Handle Assembly
1
43
0111-008-208A
Hex Bolt M8*20
2
44
0116-208-508A
Flat Washer φ8*φ28
2
45
RC800-221-003
Five-way Tube 2
1
46
RC800-391-012
Hex Nut M20*1.0
1
47
RC803-300-002PZ
Swing Arm Assembly R
1
48
RC800-801-015
Foot Tube End Cap φ50*13.5
2
49
0113-105-108
M5*10 Phillips Head Screw
2
50
RC803-360-001PZ
Seat Back Assembly
1
51
RC804-240-001
Pedal Arm Assembly
2
52
0110-412-599
Hex Flange Nut M12*1.25
2
53
RC800-801-010
Upper Pedal L
1
54
RC803-300-001PZ
Swing Arm Assembly L
1
55
RC800-310-002
Foot Pedal Tube Assembly R
1
56
0114-742-198
Cross Self-Tap Bolt ST4.2*19
33
25
57
0114-142-088
Cross Self-Tap Bolt ST4.2*8
12
58
RC800-801-013
R Lower Pedal
1
59
RC800-801-012
R Upper Pedal
1
60
RC803-630-001C
Console Wire
1
61
RC800-801-020
Adjustment Foot M12
3
62
RC800-340-001PZ
Front Stabilizer Assembly
1
63
RC800-301-009
Upper Bushing φ48*18
2
64
RC800-801-011
L Lower Pedal
1
65
RC800-310-001
Foot Pedal Tube Assembly L
1
66
BC770-801-011
Sensor Bracket
1
67
0110-412-008
Flange Nut M12*1.75
2
68
BC12-011-92
Tension U Plate
2
69
0114-142-108A
Inner Hex Socket Bolt ST4.2*10
2
70
B470-380-001
Bottle Holder
1
71
RC800-801-202A
Knob
3
72
RC803-630-001D
Resistance Motor
1
73
BE480-881-005A
End Cap
2
74
RC800-801-007A
Front Shroud L
1
75
RC803-370-001PZ
Seat Support Assembly
1
76
RC803-201-004
Power supply socket
1
77
RC804-200-002
Switch Strength Bracket
1
78
RC803-501-001
Belt 470J8VEGA)
1
79
RC804-220-001PZ
Belt Pulley Assembly
1
80
RC803-630-001E
Power Inlet
1
81
RM610-881-101
Seat
2
82
RC803-201-005
Connection Tube
1
83
RC803-630-001F
Console Lower Wire
1
84
RC804-561-018
Aluminum Plate 2
2
85
RC804-320-001PZ
Foot Pedal Connection Tube Assembly
2
86
0113-208-708
Hex Bolt M8*70
1
26
ALTERNATE ADAPTER CABLE OPTIONS (to be ordered separately)
TYPE
PART NUMBER
COUNTRIES
PHOTO
A-
type
RC802-631-002
United States, Japan, Phillipines,
Canada, Columbia, Ecuador,
Honduras, Mexico, Panama, Peru,
Taiwan
I-type
RC802-631-003
Australia, New Zealand, China
C-
type
RC802-631-004
Europe, Argentina, Russia,
Brazil, Egypt, India, Indonesia,
Israel, Pakistan, South Korea,
South Africa
G-
type
RC802-631-005
United Kingdom, Hong Kong,
Singapore
27
28
29
30
Warranty
This Warranty applies to Inspire
Cardio
products manufactured or distributed by Health In Motion LLC.
RESIDENTIAL WARRANTY:
10 YEAR FRAME (CS2):
Includes Main Frame and Welds
3 YEAR PARTS (CS2):
Excluding Paint and Finish (unless defective out of box)
1 YEAR LABOR (all cardio units)
Inspire Fitness warrants that the Product you have purchased from Health In Motion or from an authorized Inspire reseller is free
from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of
purchase of the Product, is your proof of the date of purchase. You must demonstrate proof of purchase to obtain a warranty.
This warranty extends only to you, the original purchaser. It is not transferable to anyone who subsequently purchases the
product from you. It excludes expendable parts such as paint and finish and cosmetic items, including, but not limited to the
following: grips, seats and labels. This Warranty becomes VALID ONLY if the Product is assembled / installed following the
instructions / directions included with the Product.
Replacement and repair of parts
During the warranty period Inspire will, at no additional charge, repair or replace the product if it becomes defective,
malfunctions, or otherwise fails to conform with this warranty under normal personal, family, or household use. In repairing
the product, Inspire Fitness may replace defective parts with, at the option of Inspire Fitness, serviceable used parts that are
equivalent to new parts in performance, or new parts. All exchanged parts and products replaced under this warranty will
become the property of Inspire Fitness. Inspire Fitness reserves the right to change manufacturers and or specification of any
part to cover any existing warranty.
Service procedures
To obtain warranty parts, you must return the parts to Inspire Fitness or an authorized Inspire Fitness retailer in its original
container (or equivalent). You must pre-pay any shipping charges, taxes, or any other charges associated with transportation of
the product. In addition, you are responsible for insuring any product shipped or returned. You assume the risk of loss during
shipment. You must present Inspire Fitness with proof-of-purchase documents (including the date of purchase, Model, and
Serial Number). Any evidence of alteration, erasing or forgery of proof -of-purchase documents will be cause to void this
warranty. You may be charged a trip charge if you are outside a reseller’s service area. Register your warranty online visit
www.inspirefitness.net
Conditions and Exceptions
This warranty does not extend to any product not purchased from Inspire Fitness or from an authorized Inspire Fitness reseller.
Labor claims must be authorized prior to performing service or they may be denied. This warranty does not extend to any
product missing a serial number or with a serial tag that has been altered or defaced. This warranty does not extend to service
calls to correct installation of the equipment or instruct owners on how to use the equipment. This warranty does not extend to
any product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts
not manufactured or sold by Inspire Fitness; (c) by modification of the product; (d) as a result of service by anyone other than
Inspire Fitness, or an authorized Inspire Fitness warranty service provider; (e) product that has not been properly maintained
(follow maintenance schedule found on product); (f) as a result of neglect. Should any product submitted for warranty service
be found to be ineligible, an estimate of repair cost will be furnished and the repair will be made if requested by you upon
Inspire Fitness receipt of payment or acceptable arrangement of payment.
31
Disclaimer
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY INSPIRE FITNESS MAKES NO OTHER
WARRANTIES; EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. INSPIRE FITNESS EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS WARRANTY. ANY IMPLIED WARRANTIES
THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS WARRANTY. NEITHER
INSPIRE FITNESS NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES. INSPIRE FITNESS IS NOT RESPOSIBLE FOR THE REPAIR OR
REPLACEMENT OF ANY PARTS THAT INSPIRE FITNESS DETERMINES HAVE BEEN SUBJECTED
AFTER THE DATE OF MANUFACTURE TO ALTERATION, NEGLECT, ABUSE, MISUSE, NORMAL
WEAR & TEAR, ACCIDENT, DAMAGE DURING TRANSIT OR INSTALLATION, FIRE, FLOOD, OR ANY
ACT OF GOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This warranty
gives you specific legal rights and you may also have other rights that may vary from state to state. This is the
only express warranty applicable to Inspire Fitness’ Inspire” branded cardio products. Inspire Fitness neither
assumes nor authorizes anyone to assume for it any other express warranty.
33

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Inspire CS2.5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Inspire CS2.5 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info