738438
28
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
ASSEMBLY & OPERATION MANUAL
RECORD SERIAL NUMBER HERE
www.inspirefitness.net by Health In Motion LLC Dec 2011
CONGRATULATIONS… You’ve just taken the first step to a healthier
and stronger body. This home gym by Inspire offers the key to unlocking
your body’s potential. Regular strength training on a home gym has been
shown to deliver a host of benefits including: increased muscle tone,
decreased body fat, improved energy levels, a reduction in stress, and
improved cardiac output. Once again, congratulations, you are on your way
to improving your self image, overall health and quality of life.
BEFORE ASSEMBLING YOUR HOME GYM
IMPORTANT: Read this entire manual before attempting to build or use
this machine. This manual contains step by step instructions for proper
assembly.
Use the parts list included in this manual to verify that all parts are
accounted for before assembly. If any parts are missing, contact the retailer
of this home gym for replacement parts. Or, call Inspire at 877-738-1729
Make sure that adequate room has been cleared before attempting to build
your home gym. A rubber mat is recommended for use under your home
gym to protect wood flooring or carpeting from damage during assembly
and usage.
This home gym is intended for indoor use only. In addition, garages and
screened in porches are not recommended due to high humidity or dust.
Certain parts including guide rods can form rust in a humid environment,
resulting in impaired function.
Service of your home gym should only be preformed by an authorized
INSPIRE retailer. Service preformed by anyone else can result in loss of
warranty. If you need help finding an authorized retailer, please contact us
directly:
Inspire Fitness
4945 East Hunter Avenue
Anaheim, CA 92807
Ph: 877-738-1729
Fx: 714-738-1728
www.inspirefitness.net
TABLE OF CONTENTS
Section Description……………………………………………………. Page
Important Safety Instructions………………………………………. 1
Tools Required………………………………………………………………… 1
Parts & Hardware List……………………………………………………. 2
Assembly Instructions………………………………………………..…. 3-20
Final Adjustments…………………………………………………………… 21
Decal Reference……………………………………………………………… 22-23
Accessories……………………………………………………………………… 24
General Maintenance Information…….…………………………… 25
Maintenance Schedule…….……………………………………………… 26
Limited Warranty…………………………………………………………….. 27
IMPORTANT SAFETY INSTRUCTIONS
Please read this entire manual and familiarize yourself with all decals and
warnings before using this home gym.
WARNING! It is necessary to inspect this home gym regularly to
maintain safety and proper function. Please use the maintenance schedule
included towards the back of this manual. Immediately replace any and all
defective or worn parts. Pay special attention to moving parts such as the
cables and pulleys and connections to accessories. See General
Maintenance section for complete details.
• Use this home gym for its intended purpose as described in this Operation
Manual or the exercise chart. Do not use attachments not recommended by
the manufacturer.
Do not hang from press arm. The press arm is not designed to
support human weight.
• Make sure bystanders are at least 5 feet away from the home gym while
it is in use.
• Keep children off the home gym at all times.
• Keep the home gym away from walls and clear of any obstructions and
furniture.
• Stop immediately if you experience shortness of breath, pain, or dizziness
during your workout. Inspire strongly recommends consulting your doctor
before starting an exercise program.
TOOLS REQUIRED FOR ASSEMBLY
• Metric socket set (including 16mm, 17mm, 18mm, 19mm, and 24mm
sockets)
• 16mm, 17mm, 18mm, 19mm, and 24mm wrenches
• Adjustable wrench
• Tape Measure
• Rubber Mallet
PAGE 1
PARTS & HARDWARE LIST
Part # Parts Description Q'ty
Qty Rec'd
Part# Hardware Description Q'ty
Qty Rec'd
1 Front Foot Assembly 1 77
Hex Bolt, M12*160
1
2
Base Frame Assembly
1 79
Hex Bolt, M16*230
4
3 Rear Foot Assembly 1 81
Hex Bolt, M10*70
6
4 Shroud Mount Rod, Lower 2 82
Hex Bolt, M12*90
1
5 Shroud Mount Bracket, Upper 1 83
Hex Bolt, M10*60
3
6 Weight Selector Tube 1 85
Hex Bolt, M10*115
1
7 Slider Assembly 1 86
Hex Bolt, M10*100
5
8 Lower Arm 2 87
Hex Bolt, M10*40
2
9 Upper Arm 2 88
Hex Bolt, M12*100
1
10 Upper Main Frame Assembly 1 89 Hex Bolt, M12*80 1
11 Lower Main Frame Assembly 1 90
Button Head Screw, M6*12
4
13 Top Beam Plate 2 93
Button Head Screw, M6*75
1
14 Press Arm Mount 1 94
Button Head Screw, M6*15
2
16 Press Arm Mount Cover Plate 1 97
Button Head Screw, M10*90
4
17 Lat Bar 1 98
Setscrew, M6*8
2
18 Press Arm Assembly 1 99
Flathead Nut, φ17*23*M6
1
20 Backpad Tilt Frame 1 100 Flat Head Nut, φ17*25.5*M6 2
21 Roller Tube 3 102
Flat Head Screw, M10*15
2
22 Pulley Bracket, Cable Tensioner 1 103
Philips Head Screw, M5*12
1
23 Seat Stem 1 106
Cap Screw, M5*10
1
24 Leg Extension Assembly 1 107
Flat washer, Φ10
24
25 Revolving Straight Bar 1 108
Flat washer, Φ12
8
26 Chain 1 111 Flat washer, Φ40*Φ16.5*2.5 8
37 Pulley Assembly, Φ3 1/2" 11 112 Arc Washer, Φ10 16
38L Shroud, Left 1 116
Lock Nut, M10
19
38R Shroud, Right 1 117
Lock Nut, M12
4
40 Step Bushing, Φ12 ID 8 118
Lock Nut, M16
4
43 Large Plastic Washer 2 120
Allen Wrench, 3mm
1
44 Foam Roller 6 121
Allen Wrench, 4mm
1
45 Endcap, Roller Tube 6 122
4-Way Po Plug Wrench, 5mm
1
47 Pop-Pin Shaft, 140 long 1 123
Allen Wrench, 6mm
1
50 Lat Bar Holder 2
51 Barrel Spacer, 1" Long 6
52 Spacer Tube, 3" long 1
53 Seat Pad 2
65 Foot Plate Assembly 1
68
Cable Assembly
1
69 Cable Ball 2
70 "U" Bracket, Cable End 2
73 Spring Clip 3
74
Adjustable Bumper
4
PAGE 2
ASSEMBLY INSTRUCTIONS
PAGE 3
STEP 1
3
Attach Front Foot Assembly (#1) to Base Frame Assembly (#2) using: Two (M10x70 Bolts)
Attach Rear Foot Assembly (#3) to Base Frame Assembly (#2) using: Two (M10x70 Bolts)
Wrench tighten all bolts now.
Page 4 5/11
STEP 2
Attach Slider Assembly (#7) to Weight Selector Tube(#6).
Install M5x10 Screw (#106) into Weight Selector Stem (#6) and tighten.
Insert two Step Bushings (#40) into the Weight Selector Tube (#6).
Attach two 3 ½” Pulleys (#37) and two 1” long Barrel Spacers (#51)
to Weight Selector Tube (#6) using:
Two (M10x70 Bolts)
Wrench Tighten Bolts Now.
Page 5 12/11
STEP 3
Attach Weight Selector Tube (#6) to Base Frame Assembly (#2) using:
One (M12x90 Bolt)
Wrench tighten bolt so there is a slight drag when moving Weight Selector
Tube. Do not over tighten.
Page 6 12/11
STEP 4
Attach Lower Arms (#8) to Base Frame Assembly (#2) using: One (M16x230 Hex Bolt)
Attach Upper Arms (#9) to Base Frame Assembly (#2) using: One (M16x230 Hex Bolt)
Wrench Tighten bolts so there is a slight drag on the Arms when moved.
Do not over tighten.
Page 7 12/11
STEP 5
11
65
Attach Lower Main Frame (#11) to Foot Plate (#65) using: Three (M10x60 Hex Bolt)
Wrench Tighten Now.
Page 8 5/11
STEP 6
11
8
8
Attach Lower Main Frame (#11) to Lower Arms (#8) using: One (M16x230 Hex Bolt)
Wrench Tighten bolt so there is a slight drag when moving Lower Main Frame.
Do not over tighten .
Page 9 12/11
STEP 7
9
9
11
Attach Upper Main Frame (#10) to Lower Main Frame (#11) using:
Four (M10*90 Allen Head Screws)
Attach Upper Main Frame (#10) to Left & Right Upper Arms (#8 & #9) using:
One (M16*230 Hex Bolt)
Wrench tighten bolts now.
Page 10 5/11
STEP 8
10
Attach Top Beam Plates (#13) and One 3 ½” Pulley (#37) to Upper Main Frame (#10) using:
Four (M10*100 Hex Bolts)
Two (1 Long barrel Spacers)
Finger Tighten Only
Attach Lat Bar Holders (#50) and One 3 ½” Pulley (#37) to Top Beam Plates (#13) Using:
One (M10*115 Hex Bolt)
One (M10*100 Hex Bolt)
One (3” Spacer Tube)
Two (1 Long barrel Spacers)
Finger tighten bolts only. No not wrench tighten until after step 9.
Page 11
12/11
STEP 9
13
117
108
108
88
14
47
10
Attach Press Arm Mount (#14) to Top Beam Plates (#13) using: One (M12*100 Hex Bolt)
Wrench Tighten bolt #88 so there is a slight drag when moving Press Arm Mount.
Do not over tighten .
Wrench tighten all bolts installed in Step 8.
Attach Pop-Pin Shaft (#47) to Upper Main Frame (#10)
Thread Completely and Wrench Tighten.
Page 12
12/11
STEP 10
18
14
Attach Press Arm (#18) to Press Arm Mount (#14) using: One (M12*160 Hex Bolt)
Wrench Tighten bolt so there is a slight drag when moving Press Arm.
Do not over tighten .
Page 13 12/11
STEP 11
16
14
103
117
108
108
89
24
11
Attach Leg Extension Assembly (#24) to Lower Main Frame (#11) using:
One (M12*80 Hex Bolt)
Wrench Tighten bolt so there is a slight drag when moving Leg Extension Assembly.
Do not over tighten .
Attach Press Arm Mount Cover Plate (#16) using: One (M5*12 Philips head Screw)
Wrench Tighten Now.
Page 14 12/11
STEP 12
21
43
44
45
98
45
44
43
99
93
20
10
Attach Back Pad Tilt Frame (#20) to Upper Main Frame (#10) using:
One Roller Tube (#21) Two M6*8 Set Screws (#98)
Two Foam Rollers (#44) One M6*75 Button Head Screw (#93)
Two Large Plastic Washers (#43) One M6 Flat Head Nut (#99)
Two End Caps (#45)
Wrench Tighten bolt #93 so there is a slight drag when moving Back Pad tilt Frame.
Do not over tighten .
Note: Tighten the two set screws(#98) completely after Foam Rollers are installed.
Page 15 12/11
STEP 13
53
53
102
102
87
87
107
107
20
23
Attach Seat Pad (#53) to Seat Stem (#23) using: Two (M10*40 Hex Bolts)
Wrench Tighten Now.
Slide Seat Stem (#23) into Lower Main Frame (#11)
Attach Back Pad (#53) to Backpad Tilt Frame (#20) using: Two (M10*15 Flat Head Screws)
Wrench Tighten Now.
Page 16 5/11
STEP 14
44
44
45
45
21
21
44
44
45
45
24
Attach 4 Foam Rollers (#44) to Leg Extension Assembly (#24) & Seat Stem (#23) using:
Two Roller Tubes (#21)
Four End Caps (#45)
Page 17 12/11
STEP 15
Pulley 1
Pulley2
100
68
69
70
94
73
Pulley 3
Pulley 4
Pulley 5
Pulley 6
Pulley 8
Pulley 11
Pulley 9
Pulley 7
Pulley 10
Began at the top of the machine and run the cable sequentially from pulley #1 to pulley #11,
as shown in the above drawing. Once complete, finish both cable ends with a plastic ball
(#69), “U” bracket (#70), flat head nut (#100), button head bolt (#94), and a spring clip
(#73). Look back over the cable routing to make sure that the cable is sitting securely in
each pulley.
Note: Wrench tighten “U” bracket hardware at both ends of the cable.
Page 18 5/11
STEP 16
38R
38L
90
90
4
5
Attach Left and Right Shrouds (#38L & #38R) by first slipping the top of each Shroud onto the
horns of the upper shroud mount (#5), as shown above. Make sure seams are to the inside.
Next, slide rods (#4) into the bottom of each shroud and attach to frame using:
Four M6*12 Button Head Screws
Note: Be sure to pull the shrouds down taut before tightening the four screws.
Page 19 12/11
STEP 17
17
73
25
73
26
73
Attach Lat Bar (#17) to Spring Clip (#73).
Attach Chain (#26) to Spring Clip (#73) on the end of the Cable.
Attach Revolving Curl Bar (#25) to Chain (#26) with Spring Clip (#73).
Page 20 5/11
FINAL ADJUSTMENTS AFTER ASSEMBLY
Press Arm Stop
Macro Cable Adjustment
Nut #2
Nut #1
Weight
Selector
Handle
Wooden Platform
Front Rubber Bumper
Weight Selector Rollers
Page 21
081711
FINAL ADJUSTMENT: (if needed)
Below the seat you will find the weight selector. Grab the weight selector handle and pull the spring
loaded pin. Slide the weight selector from position one to fifteen. The rollers should move freely. If the
weight selector rollers bind between positions 1-8, lift the wooden platform and adjust the two Front
Rubber Bumpers up slightly. This will ease the pressure on the rollers and allow the weight selector
mechanism to slide freely.
If the Weight Selector Rollers bind between positions 8-15, thread the press arm stop completely into the
frame. This will provide slack in the cable and ease the pressure on the Weight Selector Rollers. If the
Weight Selector Rollers are still binding, loosen nut #1 in the Macro Cable Adjustment drawing above.
Next, adjust nut #2 counter clockwise until the Weight Selector Rollers move freely. Re-tighten nut #1.
NOTE:
The cable on this gym will stretch over time. There are two places to eliminate cable slack. A large
amount of cable slack can be removed by adjusting the pulley upward on the Macro Cable Adjustment.
Start by loosening nut (#1) shown in the Macro Cable Adjustment drawing above. Next, using a wrench,
turn nut (#2) clockwise until adequate cable slack has been removed. Finish by tightening nut #1 back
up.
To eliminate a small amount of cable slack, adjust the Press Arm Stop counter clockwise. Wrench tighten
Jam Nut.
DECAL REFERENCE
877-738-1729
PAGE 22
DECAL REFERENCE
PAGE 23
ACCESSORIES
• Exercise Wall Chart
• Lat Bar
• Revolving Curl Bar
HOME GYM OPTIONS
• D handles
• Aluminum EZ Curl Bar
• Ab Crunch Bar
Training Tips
CONSULT A PHYSICIAN BEFORE STARTING ANY EXERCISE PROGRAM
1. Always warm up before you start weight training. This helps get
your muscles warm and prevents injury. You can warm up with light
cardio or by doing a light set of each exercise before going to heavier
weights.
2. Control the weight. Always work with a weight that you can handle
through a full range of motion. Slow and steady movements are
recommended.
3. Breathe. Don’t hold your breath during your set. Holding your
breath builds internal pressure which increases your change for broken
blood vessels, as well as a hernia.
4. Sit up straight. Pay attention to your posture and keep everything
straight. Engage your abs in every movement to keep balanced and
protect your spine.
PAGE 24
GENERAL MAINTENANCE INFORMATION
• Periodically inspect the cables for splitting, cracking or fraying. Also,
watch for bulging or flat areas in the cable.
• Immediately replace cables at the first signs of damage or wear. Never
use equipment with damaged or worn cables.
• Cables naturally stretch over time, so check cable slack periodically and
adjust cable tension as needed.
• Regularly inspect product for loose hardware.
• Do not use or store equipment outdoors.
• Inspect spring clips, swivels and handles for wear or damage. If wear or
damage exists, replace immediately.
• Locate and familiarize yourself with all warning decals on the home gym.
• Replace damaged or worn upholstery immediately.
PAGE 25
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Inspire BL1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Inspire BL1 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info