509747
17
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
- 17 -
Under some rare circumstances it is possible that the heater calibration data in the LC-1 can
become partially destroyed. This can manifest in the above-mentioned errors. Follow the steps in
chapter 4 ‘First time use’ to reset the heater calibration data.
7.7 Sensor Timing Errors
These errors are typically encountered when the sensor does not have outside air available as
reference gas. If you encounter this error, restart the LC-1 and operate the sensor in free air. If
you still encounter this error, the sensor may be bad and needs to be replaced.
Replacement sensors are available from your nearest VW dealer under the VW part-number
021-906-262-B or direct from Innovate Motorsports.
Sensor timing errors are also common when the sensor overheats. Relocate the sensor further
downstream in the exhaust, install a heat sink or Heat-Sink Bung extender (HBX-1).
Sometimes it’s possible to encounter Error 08 when the exhaust gas suddenly gets too rich.
Normally the LC-1 will display a ‘too rich’ indication if the exhaust gas is too rich. If the mixture
gets rich very suddenly, the LC-1 cannot distinguish between a too rich condition and a sensor
timing error.
7.8 Analog Output tricks/hints
Sometimes there is a ground offset between the device that receives the analog output voltage
and the LC-1. This can be especially true if the System ground is not connected to the same
ground as the measurement device using the analog out. Both devices reference different
grounds and therefore see different voltages. So to compensate for the ground offsets the analog
output voltage points have to be shifted by the ground offsets. To measure what the real ground
offset is, you can program the analog outputs temporarily to output a flat line voltage by entering
the same voltage in both fields for the two analog out programming points. This way the analog
output voltage will be fixed, independent of current AFR and can therefore be measured and
compensated for easily.
To log analog outputs from the LC-1 into an LM-1, simply connect analog output #2 (brown wire)
to an available input on the LMA-2 (RPM converter Aux. In Cable) or LMA-3 (5-sensor “AuxBox”).
Set LogWorks inputs match the LC-1 outputs. As discussed in section 7.6 above, factory settings
for the second output is programmed where 0V=.5λ (AFR of 7.35 for gasoline) and 5.0V=1.523λ
(AFR of 22.39 for gasoline).
Note:
The analog outputs are NOT designed to power other devices or sensors.
So using the flat-line setting at 5V and expecting to power a sensor from it
will not work and can damage the LC-1.
8 Advanced Topics
8.1 Connecting the LC-1 to simulate a narrow band oxygen sensor.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Innovate LC-1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Innovate LC-1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info