749835
59
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
NEDERLANDS 59
Installatie
LET OP: Als het apparaat op een bepaald moment moet worden
verplaatst, houd het dan rechtop; als dit absoluut noodzakelijk
is, kan het op de rug worden gekanteld.
De watertoevoer aansluiten
Het aansluiten van de watertoevoer voor installatie mag alleen
door een gekwaliceerde technicus worden uitgevoerd.
De watertoevoer- en afvoerslangen kunnen naar rechts of naar
links worden geplaatst, voor een zo goed mogelijke installatie.
Zorg ervoor dat er door de afwasmachine geen knikken in de
slangen komen of dat de slangen geplet worden.
De toevoerslang aansluiten
Het water laten lopen totdat het volkomen helder is.
De toevoerslang strak aandraaien naar de gewenste positie
en de kraan open draaien.
Als de toevoerslang niet lang genoeg is, neem dan contact op
met een specialistische winkel of een erkende technicus.
De waterdruk moet binnen de waarden vallen die in de
tabel Technische Gegevens staan aangegeven - dan kan de
afwasmachine naar behoren functioneren.
Zorg ervoor dat er geen knik in de slang zit of dat de slang niet
samengedrukt is.
Specicatiesvoordewateraansluiting
Watertoevoer koud of warm (max. 60°C)
Waterinlaat 3/4”
Vermogen van het water
Druk
0.05 ÷ 1MPa (0,5 ÷ 10 bar)
7.25 – 145 psi
Toevoerslang:
De waterafvoerslang aansluiten
De afvoerslang aansluiten op een aftapleiding met een
minimale diameter van 2 cm A.
INSTALLATION
ENGLISH
ATTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be tilted onto
its back.
CONNECTING THE WATER SUPPLY
Adaptation of the water supply for installation should only be
performed by a qualified technician
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE WATER INLET HOSE
Run the water until it is perfectly clear.
Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
Technical Data table - otherwise the dishwasher may be function
properly.
Make sure the hose is not bent or compressed.
SPECIFICATIONS FOR THE CONNECTION OF THE WATER
SUPPLY HOSE:
CONNECTING THE WATER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter
of 2 cm A.
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher rests
Before connecting the water outlet hose to the sink drain, remove
the plastic plug B.
ANTI-FLOODING PROTECTION
Anti-flooding protection. To ensure floods do not occu , the dishwasher
is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Aqua Stop, which guarantees anti-flooding protectio
even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
ELECTRICAL CONNECTION
WARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
The socket is earth and complies with current regulations;
The socket can withstand the maximum load of the applian-
ce as shown on the data plate located on the inside of the door
(see PRODUCT DESCRIPTION).
The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SERVICE). Do not use extension ca-
bles or multiple sockets. Once the appliance has been installed,
the power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised Technical Assistance Service in
order to prevent all potential hazards.
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
POSITIONING AND LEVELLING
1.
2.
Position the dishwasher on a level sturdy floo . If the floor i
uneven, the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before recessing the dishwasher, stick the adhesive transparent
strip under the wooden shelf in order to protect it from any con-
densation which may form.
3.
4.
Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the height and in
an anticlockwise direction to decrease it.
DIMENSIONS AND CAPACITY:
MIN 40 cm
MAX 80 cm
WATER SUPPLY cold or hot (max. 60°C)
WATER INTAKE 3/4”
POWER OF WATER
PRESSURE
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 145 psi
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAPACITY 13 standard place-settings
De aansluiting van de afvoerslang moet zich op een hoogte
bevinden die varieert van 40 tot 80 cm van de vloer of
het oppervlak waar de vaatwasser staat. Voordat u de
waterafvoerslang aansluit op de gootsteen, moet u de plastic
plug B verwijderen.
Anti-overstromingbeveiliging
Anti-overstromingbeveiliging. Om te voorkomen dat er
overstromingen optreden, is de vaatwasser voorzien van een
speciaal systeem dat de watertoevoer blokkeert bij defecten of
lekken binnen het apparaat.
Een aantal modellen zijn ook uitgerust met het
extra veiligheidssysteem New Aqua Stop, dat anti-
overstromingbeveiliging zelfs garandeert bij een breuk in de
toevoerslang.
Het model heeft het waterbeschermingssysteem Aquastop
De watertoevoerslang mag onder geen beding worden
doorgesneden, omdat het elektrische delen bevat.
Elektrische aansluiting
WAARSCHUWING: De watertoevoerslang mag onder geen
beding worden doorgesneden, omdat het elektrische delen
bevat.
Voordat de stekker in het stopcontact wordt gestoken ervoor
zorgen dat:
Het stopcontact geaard is en aan de huidige regelgeving
voldoet;
Het stopcontact bestand is
INSTALLATION
ENGLISH
ATTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be tilted onto
its back.
CONNECTING THE WATER SUPPLY
Adaptation of the water supply for installation should only be
performed by a qualified technician
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE WATER INLET HOSE
Run the water until it is perfectly clear.
Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
Technical Data table - otherwise the dishwasher may be function
properly.
Make sure the hose is not bent or compressed.
SPECIFICATIONS FOR THE CONNECTION OF THE WATER
SUPPLY HOSE:
CONNECTING THE WATER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter
of 2 cm A.
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher rests
Before connecting the water outlet hose to the sink drain, remove
the plastic plug B.
ANTI-FLOODING PROTECTION
Anti-flooding protection. To ensure floods do not occu , the dishwasher
is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Aqua Stop, which guarantees anti-flooding protectio
even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
ELECTRICAL CONNECTION
WARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
The socket is earth and complies with current regulations;
The socket can withstand the maximum load of the applian-
ce as shown on the data plate located on the inside of the door
(see PRODUCT DESCRIPTION).
The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SERVICE). Do not use extension ca-
bles or multiple sockets. Once the appliance has been installed,
the power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised Technical Assistance Service in
order to prevent all potential hazards.
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
POSITIONING AND LEVELLING
1.
2.
Position the dishwasher on a level sturdy floo . If the floor i
uneven, the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before recessing the dishwasher, stick the adhesive transparent
strip under the wooden shelf in order to protect it from any con-
densation which may form.
3.
4.
Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the height and in
an anticlockwise direction to decrease it.
DIMENSIONS AND CAPACITY:
MIN 40 cm
MAX 80 cm
WATER SUPPLY cold or hot (max. 60°C)
WATER INTAKE 3/4”
POWER OF WATER
PRESSURE
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 145 psi
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAPACITY 13 standard place-settings
tegen de maximale belasting
van het apparaat, zoals staat aangegeven op het typeplaatje
aan de binnenkant van de deur (zie PRODUCTBESCHRIJVING).
Het netspanningsvoltage binnen de waarden valt die staan
aangegeven op het typeplaatje aan de binnenkant van de
deur.
Het stopcontact is compatibel met de stekker van het
apparaat.
Als dit niet het geval is vraag dan een erkende monteur om de
stekker te vervangen (zie CONSUMENTENSERVICE). Gebruik
geen verlengkabels of meervoudige stopcontacten. Zodra
het apparaat is geïnstalleerd moeten de stroomkabel en het
stopcontact gemakkelijk toegankelijk zijn.
De kabel moet zonder knikken en niet samengeperst zijn.
Als de stroomkabel beschadigd is deze laten vervangen door
de fabrikant of een erkende technische hulpdienst, om alle
mogelijke gevaren te voorkomen.
Het bedrijf is niet aansprakelijk voor eventuele incidenten, als
deze voorschriften niet worden nageleefd.
Plaatsen en waterpas zetten
1. Plaats de afwasmachine op een vlakke stevige vloer. Als de
vloer ongelijk is kunnen de voorste poten van het apparaat
worden afgesteld, totdat het horizontaal staat. Als het
apparaat correct waterpas staat is het stabieler en is er
veel minder kans dat het beweegt of trillingen en lawaai
veroorzaakt tijdens de werking.
2. Voordat de afwasmachine in een nis wordt gezet de
zelfklevende transparante strip onder de houten plank
vastplakken, om het te beschermen tegen eventuele
condensatievorming.
3. Plaats de afwasmachine zodanig dat de zijkanten of
achterzijde tegen de aangrenzende kasten of de muur
aankomen. Dit apparaat kan ook worden ingebouwd onder
een enkel aanrechtblad.
4. Voor het afstellen van de hoogte van de achterste voet de
rode zeshoekige bus op het lagere middengedeelte aan de
voorkant van de afwasmachine draaien met een zeshoekig
moersleutel met een opening van 8 mm. . De moersleutel
naar rechts draaien om de hoogte te vergroten en naar links
om de hoogte te verkleinen.
Afmetingen en capaciteit:
Breedte 598 mm
Hoogte 820 mm
Diepte 555 mm
Capaciteit 13 standaard couverts
59

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ikea-Rengora-404.755.72

Zoeken resetten

  • Code 11, Vaatwasser 404.755.72 IKEA:
    sinds er een stroomstoring is geweest in onze straat geeft onze vaatwasser foutmelding 11. Deze is niet terug te vinden in de handleiding.
    Het apparaat pompt eerst bij aanzetten en valt dan stil, ook na de stroom er enige minuten afgehaald te hebben om te resetten.
    Heeft iemand hier ervaring mee?

    Vrgr, TK Gesteld op 21-7-2023 om 14:20

    Reageer op deze vraag Misbruik melden
  • Onze vaatwasser als deze klaar is code 15 aan
    wat beteken dit Gesteld op 30-9-2022 om 11:31

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ikea Rengora 404.755.72 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ikea Rengora 404.755.72 in de taal/talen: Nederlands, Portugees, Spaans als bijlage per email.

De handleiding is 18,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ikea Rengora 404.755.72

Ikea Rengora 404.755.72 Gebruiksaanwijzing - Deutsch, English, Français, Italiano - 64 pagina's

Ikea Rengora 404.755.72 Aanvulling / aanpassing - Alle talen - pagina's

Ikea Rengora 404.755.72 Installatiehandleiding - Alle talen - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info