749836

Ikea Finputsad 704.756.22 Handleiding

17
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
PORTUGUÊS 17
Instalação
ATENÇÃO: Se for necessário mover o aparelho, mantenha-o
sempre na posição vertical; se for absolutamente necessário
incliná-lo, incline-o para trás.
Ligar ao abastecimento de água
A adaptação do abastecimento de água para a instalação só
deve ser efetuada por um técnico qualicado.
As mangueiras de entrada e de escoamento da água podem
ser posicionadas à esquerda ou à direita para permitir a melhor
instalação.
Certique-se de que a máquina de lavar loiça não dobra nem
esmaga as mangueiras.
Ligar a mangueira de entrada da água
• Coloque a água a correr até estar completamente límpida.
• Aperte bem a mangueira de entrada na posição correta e
ligue a torneira.
Se a mangueira de entrada não for sucientemente comprida,
dirija-se a uma loja especializada ou entre em contacto com um
técnico autorizado.
A pressão da água tem de estar dentro dos valores indicados
na tabela de dados técnicos; caso contrário, a máquina de lavar
loiça poderá não funcionar corretamente.
Certique-se de que a mangueira não está dobrada nem comprimida.
Especicaçõesparaaligaçãodaágua
Abastecimento de água fria ou quente (máx. 60 °C)
Entrada de água 3/4”
Força da água
Pressão 0,05 ÷ 1 MPa (0,5 ÷ 10 bar)
7,25 – 145 psi
Mangueira de alimentação:
Ligar a mangueira de escoamento de água
Ligue a mangueira de escoamento a uma conduta de
escoamento com um diâmetro mínimo de 2cm A.
INSTALLATION
ENGLISH
ATTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be tilted onto
its back.
CONNECTING THE WATER SUPPLY
Adaptation of the water supply for installation should only be
performed by a qualified technician
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE WATER INLET HOSE
• Run the water until it is perfectly clear.
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
Technical Data table - otherwise the dishwasher may be function
properly.
Make sure the hose is not bent or compressed.
SPECIFICATIONS FOR THE CONNECTION OF THE WATER
SUPPLY HOSE:
CONNECTING THE WATER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter
of 2 cm A.
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher rests
Before connecting the water outlet hose to the sink drain, remove
the plastic plug B.
ANTI-FLOODING PROTECTION
Anti-flooding protection. To ensure floods do not occu , the dishwasher
is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Aqua Stop, which guarantees anti-flooding protectio
even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
ELECTRICAL CONNECTION
WARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the applian-
ce as shown on the data plate located on the inside of the door
(see PRODUCT DESCRIPTION).
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SERVICE). Do not use extension ca-
bles or multiple sockets. Once the appliance has been installed,
the power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised Technical Assistance Service in
order to prevent all potential hazards.
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
POSITIONING AND LEVELLING
1.
2.
Position the dishwasher on a level sturdy floo . If the floor i
uneven, the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before recessing the dishwasher, stick the adhesive transparent
strip under the wooden shelf in order to protect it from any con-
densation which may form.
3.
4.
Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the height and in
an anticlockwise direction to decrease it.
DIMENSIONS AND CAPACITY:
MIN 40 cm
MAX 80 cm
WATER SUPPLY cold or hot (max. 60°C)
WATER INTAKE 3/4”
POWER OF WATER
PRESSURE
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 – 145 psi
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAPACITY 13 standard place-settings
A ligação da mangueira de escoamento deve estar a uma altura
entre 40 a 80 cm do chão ou superfície onde a base da máquina
de lavar loiça está instalada. Antes de ligar a mangueira de
escoamento de água à conduta de escoamento, remova o
tampão de plástico B.
Proteção contra inundação
Proteção contra inundação. Para evitar inundações, a máquina
de lavar loiça vem equipada com um sistema especial que
bloqueia o abastecimento de água em caso de anomalias ou de
fugas no interior do aparelho.
Alguns modelos também estão equipados com um dispositivo
de segurança suplementar, o novo Aqua Stop, que garante uma
proteção contra inundações mesmo em caso de ruptura de uma
mangueira de abastecimento.
O modelo dispõe de um sistema de proteção de água Aquastop
A mangueira de entrada de água nunca deve ser cortada, pois
contém peças com corrente elétrica.
Ligação elétrica
AVISO: A mangueira de entrada de água nunca deve ser
cortada, pois contém peças com corrente elétrica.
Antes de ligar a cha à tomada, certique-se de que:
• A cha está ligada à terra e está em conformidade com os
regulamentos atuais;
• A tomada suporta
INSTALLATION
ENGLISH
ATTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be tilted onto
its back.
CONNECTING THE WATER SUPPLY
Adaptation of the water supply for installation should only be
performed by a qualified technician
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE WATER INLET HOSE
• Run the water until it is perfectly clear.
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
Technical Data table - otherwise the dishwasher may be function
properly.
Make sure the hose is not bent or compressed.
SPECIFICATIONS FOR THE CONNECTION OF THE WATER
SUPPLY HOSE:
CONNECTING THE WATER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter
of 2 cm A.
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher rests
Before connecting the water outlet hose to the sink drain, remove
the plastic plug B.
ANTI-FLOODING PROTECTION
Anti-flooding protection. To ensure floods do not occu , the dishwasher
is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Aqua Stop, which guarantees anti-flooding protectio
even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
ELECTRICAL CONNECTION
WARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the applian-
ce as shown on the data plate located on the inside of the door
(see PRODUCT DESCRIPTION).
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the
plug (see AFTER-SALES SERVICE). Do not use extension ca-
bles or multiple sockets. Once the appliance has been installed,
the power supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised Technical Assistance Service in
order to prevent all potential hazards.
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
POSITIONING AND LEVELLING
1.
2.
Position the dishwasher on a level sturdy floo . If the floor i
uneven, the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
Before recessing the dishwasher, stick the adhesive transparent
strip under the wooden shelf in order to protect it from any con-
densation which may form.
3.
4.
Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the height and in
an anticlockwise direction to decrease it.
DIMENSIONS AND CAPACITY:
MIN 40 cm
MAX 80 cm
WATER SUPPLY cold or hot (max. 60°C)
WATER INTAKE 3/4”
POWER OF WATER
PRESSURE
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 – 145 psi
WIDTH 598 mm
HEIGHT 820 mm
DEPTH 555 mm
CAPACITY 13 standard place-settings
a carga máxima da máquina,
apresentada na chapa de dados existente no interior da
porta (consultar a secção DESCRIÇÃO DO PRODUTO).
• A tensão de abastecimento de energia está dentro dos
valores indicados na chapa de dados existente no interior da
porta.
• a tomada é compatível com a cha do aparelho.
Se não for este o caso, contacte um técnico autorizado para
que substitua a cha (consultar a secção SERVIÇO PÓS-VENDA).
Não use extensões elétricas ou tomadas múltiplas. Depois de
a máquina estar instalada, o cabo de alimentação e a tomada
elétrica devem estar facilmente acessíveis.
O cabo não deve estar dobrado nem comprimido.
Se o cabo de alimentação estiver danicado, contacte o fabricante
ou o respetivo serviço de assistência técnico autorizado para o
substituir, a m de evitar todos os potenciais perigos.
A Empresa não será responsabilizada por quaisquer incidentes
caso estas regras não sejam cumpridas.
Posicionamento e nivelamento
1. Posicione a máquina de lavar loiça num piso nivelado e
resistente. Se o piso for irregular, os pés dianteiros podem
ser ajustados até a máquina car numa posição horizontal.
Se a máquina estiver bem nivelada, cará mais estável e é
muito menos provável que cause vibrações e ruído durante o
funcionamento.
2. Antes de encaixar a máquina de lavar loiça no devido local,
cole a faixa transparente adesiva por baixo da prateleira de
madeira, para que que protegida de qualquer condensação
que possa formar-se.
3. Posicione a máquina de lavar loiça de modo a que os lados
ou o painel traseiro quem em contacto com os armários
adjacentes ou com a parede. Este aparelho também pode ser
encastrado sob um balcão de cozinha.
4. Para ajustar a altura do pé traseiro, rode o casquilho
hexagonal vermelho na parte central inferior pela parte
dianteira da máquina de lavar, utilizando uma chave
hexagonal com uma abertura de 8 mm. Rode a chave no
sentido dos ponteiros do relógio para aumentar a altura e no
sentido contrário para a diminuir.
Dimensões e capacidade:
Largura 448 mm
Altura 820 mm
Profundidade 555 mm
Capacidade 10 talheres padrão
… 17 …

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ikea-Finputsad-704.756.22

Zoeken resetten

  • De platte pen die na de wasbeurt de deur automatisch opent gaat niet meer terug. Daardoor kan de deur niet meer dicht en kan er dus ook geen nieuwe wasbeurt meer gestart worden. Wat nu te doen? Gesteld op 4-1-2025 om 19:10

    Reageer op deze vraag Misbruik melden

  • Vaatwasser begint. Maar na een tijdje stop hij. Piept 2 x en knippert op het programma. Geen foutmelding?!
    Weet iemand wat hier aan de hand is Gesteld op 17-6-2024 om 13:20

    Reageer op deze vraag Misbruik melden

    • Juist ook aan de hand gehad.
      Was dat ook bij programma 4?
      Ik heb m terug toe gedaan en na een tijd sprong hij open voor het drogen. Hij was toen ook uitgeschakeld.
      Ik denk dat hij einde programma aangeeft bij gepiep, nog effe blijft drogen en dan de deur open laat gaan. Geantwoord op 2-9-2024 om 13:05

      Waardeer dit antwoord (1) Misbruik melden

  • HI. Gisteren de afwasmachine geïnstalleerd ( FINPUTSAD) deze eerst zoals aangegeven leeg gedraaid. Nu bij de official draai. Gebeurt er niks. Draait even blijft dan vast staan ( display zegt 15 en loopt niet leeg. Wat gaat er mis?
    Gesteld op 4-5-2024 om 13:18

    Reageer op deze vraag Misbruik melden

  • De deur blijft niet plat en het moment van schuiven ( open of dicht) valt telkens Gesteld op 12-8-2022 om 13:58

    Reageer op deze vraag Misbruik melden

  • Deur wordt niet vergrendeld. Rekken zijn goed geplaatst Gesteld op 2-1-2022 om 11:55

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ikea Finputsad 704.756.22 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ikea Finputsad 704.756.22 in de taal/talen: Nederlands, Portugees, Spaans als bijlage per email.

De handleiding is 45.97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Ikea Finputsad 704.756.22

Ikea Finputsad 704.756.22 Gebruiksaanwijzing - Deutsch, English, Français, Italiano - 68 pagina's

Ikea Finputsad 704.756.22 Installatiehandleiding - Alle talen - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info