Load the laundry, close the door and add detergents as
indicated on the front page and as described in the chapter
“Detergent and Additives” in your Instructions for Use.
1. Turn the programme selector to the desired
programme and temperature.
2. The time display shows the duration of the chosen
programme (in hours and minutes), and the “Start
(Pause)” indication lamp is flashing.
3. The indication lamp of the predefined spin speed
lights up.
If you do not start the programme soon after having
made your choice, the washing machine will switch off
automatically after about a quarter of an hour. Switch on the
washing machine again by turning the programme selector
back to “O” and then to the desired programme.
LOAD LAUNDRY, ADD DETERGENTS
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
Push the button of any option desired - the respective
indication lamp lights up. When the combination of
programme and additional option(s) is not possible, the
indication lights switch off automatically.
“Clean+” button
•Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Use with the maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together
with your detergent (only use powder detergent with this
option). Respect the manufacturer’s dosing instructions.
• May prolongs the programme by up to 15 minutes
• Appropriate for use of stain removers and bleaches
on oxygen basis. Chlorine or perborate bleaches
must not be used!
“Cold wash” button
• Saves energy used for water heating while maintaining
good wash result.
• Recomentable for lightly soiled laundry without stains.
• Make sure that your detergent is suitable for cold
wash temperatures (15 or 20 °C).
• Mainly selectable on the lowest temperature step of
the programmes.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very
soft water, washing baby linen and helps people with
allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and
a very gentle spin.
“Rinse hold” button
•The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
•It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer to
“Cancel (Reset) a running programme before the end”.
PROGRAMME START
Open the tap and press the “Start(Pause)” button. The
indication lamp next to the “Start(Pause)” button lights
up. The programme sequence indicator shows the current
programme phase, running from left to right through Wash,
Rinse, Spin/Drain.
PROGRAMME END
The “Door open” indicator lights up, and the display shows
“End”. After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start(Pause)” button to pause the
programme. The light flashes.
2. Select the new programme, any options and another spin
speed if you want.
3. Press the “Start(Pause)” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the end.
•Press and hold the “Reset” button for a few
seconds. Any existing water is drained out. It may last
some time until the door can be opened.
•The programme stops to “Rinse hold” at the time the
“Rinse hold” lights in the preogramme sequence
indication is on. The “Start/Pause” indicator blinks.
Terminate the “Rinse hold” option:
•Press the “Start/Pause” button; the programme will
terminate automatically with the final spin cycle for the
present wash programme.
•If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme and press
the “Start/Pause” button.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If spin speed “0” is selected, the final spinning is cancelled
but intermediate spin peaks remain during the rinse.
The water is drained out only.
“Prewash” button
•Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
• Recommended for heavily soiled laundry (e.g. with sand
or granular dirt).
•Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Rapid” button
• Enables quicker washing by shortening the programme
duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 95°
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating “Start delay” option.
•Select programme, temperature and options.
•Press the “Start delay” button to select the delay time by
1 to 23 hours.
•Press the “Start(Pause)” button.
The countdown of the delay time begins; the “Start
delay” indication lamp and the dot on the display will
keep blinking until the programme starts.
•The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
•Once having pressed the “Start(Pause)” button,
the number of hours preselected can be reduced by
pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start(Pause)” button:
•Turn the programme selector to another position or
press the “Reset” button.
..after having pressed the “Start(Pause)” button:
•Press the “Start(Pause)” - the start delay time
disappears from the time display.
START DELAY
FAILURE INDICATIONS
The time display shows the remaining programme time.
Due to variations in load and temperature of inlet water, the
remaining time is newly calculated in certain programme
phases. If this is the case, an animation appears on the time
display.
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
without “Rapid”
Approx. programme duration
(hours : minutes)
without “Rapid”with “Rapid”
Cotton956.059**1.902:00-
Cotton606.0491.022:301:35
Cotton406.0540.652:001:15
Synthetics603.050**0.701:351:14
Synthetics403.0460.501:200:59
Delicates401.5500.650:50-
Delicates301.5500.500:46-
Daily load403.0450.451:00-
Quick wash303.0400.300:30-
Wool/Handwash401.0450.600:40-
Wool/Handwashcold1.0450.100:35-
Cotton
60°
*606.0490.784:00-
Cotton
60°
*603.0370.692:20 ***-
Cotton
40°
*403.0370.582:30-
Ignis is a registered trademark of Whirlpool USA.
5019 550 00002/A
CONSUMPTION DATA
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the energy
consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default setting of the
programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also “Troubleshooting
Guide” in your Instructions for Use).
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
”Service”: failure or malfunction of an electrical
component.
”Clean pump”: waste water is not pumped out.
Spin speed on display blinks : unbalance during spinning.
de grote wiel waarop de v-snaar op zit komt bovenin tegen de achterkant van de trommel tydens het draaien en komt vast te zitten
Gesteld op 12-1-2020 om 18:08
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Ignis AWP 1406 bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Ignis AWP 1406 in de taal/talen: Engels als bijlage per email.
De handleiding is 0,71 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
