534174
15
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
CONTENTS
DEFINITION OF USE
BEFORE USING THE WASHING MACHINE
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE
BEFORE THE FIRST WASH CYCLE
PREPARATION OF THE WASHING
DETERGENTS AND ADDITIVES
CLEANING THE FILTER/
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
TRANSPORT AND HANDLING
INSTALLATION
ELECTRICAL CONNECTION
IFU-TL HR GB.fm Page 1 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
GB 2
DEFINITION OF USE
This washing machine is exclusively destined to wash
machine washable laundry in quantities which are usual
for private households.
Observe the instructions given in these Instructions
for Use and the Programme Chart when using the
washing machine.
Keep these Instructions for Use and the Programme
Chart; if you pass on the washing machine to
another person, also give him/her Instructions for
Use and Programme Chart.
BEFORE USING THE WASHING MACHINE
1. Remove the packaging and check
a.
Cut and remove the shrink-wrap.
b.
Remove the top protection and the protective
corners.
c. Remove the bottom protection by tilting and
turning the washing machine on one rear
bottom corner. Make sure that the black
plastic part of the bottom protection (if
available on the model) remains in the packing
and not in the machine bottom.
This is important, as otherwise the plastic part could
damage the washing machine during operation.
d.
Open the lid by pressing it slightly down while
raising the handle. Remove the polystyrene cushion
(depending on model).
e.
Remove the blue protective film from the panel
(depending on model).
After unpacking, make sure that the washing machine is
undamaged. If in doubt, do not use the washing machine.
Contact After-Sales Service or your local retailer.
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children;
they are potentially dangerous.
If the appliance was exposed to the cold prior to
delivery, keep it at room temperature for a few
hours before operating.
2. Remove the transport bracket
The washing machine is fitted with transport screws
and a transport bracket to prevent damage during
transport.
Before using the washing machine
you must remove the transport bracket
(see
“Installation”/“Removal of transport bracket”).
3. Install the washing machine
Place the washing machine on a flat and stable floor
surface.
Adjust the feet to ensure that the machine is stable
and level (see “Installation”/“Adjust the feet”)
.
In case of wooden or so-called “floating floors” (for
instance certain parquet or laminate floors), place
the appliance on a 40 x 60 cm sheet of plywood at
least 3 cm in thickness which is secured to the floor.
Make sure that the ventilation openings in the base
of your washing machine (if available on your model)
are not obstructed by a carpet or other material.
4. Water supply
Connect the water supply inlet hose in accordance
with the regulations of your local water company
(see “Installation”/“Connect the water inlet hose”).
Water supply: Cold water only
Tap: 3/4” threaded hose connection
Pressure: 100-1000 kPa (1-10 bar).
Only use new hoses for connecting the washing
machine to the water supply. Used hoses must not
be used anymore and should be discarded.
5. Drain hose
Connect the drain hose to the siphon or hook it
over the edge of a sink with the “U” bend (see
“Installation”/“Connect the water drain hose”).
If the washing machine is connected to a built-in
drainage system, ensure the latter is equipped with
a vent to avoid simultaneous loading and draining of
water (siphoning effect).
6. Electrical connection
Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and the current
standard safety regulations.
The technical data (voltage, power and fuses) are given
on the rating plate on the rear of the washing machine.
The washing machine must be connected exclusively by
means of a socket with an earth connection in
accordance with current regulations. The washing
machine must be earthed by law. The manufacturer
declines all liability for injury to persons or animals or
damage to property deriving directly or indirectly from
failure to observe the directions.
Do not use extension leads or multi sockets.
Before any maintenance on the washing machine
disconnect it from the mains supply.
Access to the mains plug or to disconnection from the
mains supply via a double-pole switch must be ensured
at all times following the installation.
Do not operate the washing machine if it has been
damaged during transport. Inform the After-Sales Service.
Mains cable replacement is only to be carried out by
After-Sales Service.
The washing machine must be connected to an effective
earthing installation, in compliance with the regulations
in force. In particular, washing machines installed in
premises containing a shower or a bath must be
protected by a differential residual current device of at
least 30 mA. Earthing the washing machine is obligatory
under the law. The manufacturer declines all liability for
injury to persons or animals or damage to property
deriving either directly or indirectly from failure to
observe the directions in these Instructions for Use.
The washing machine may only be used in the
household for the prescribed uses.
Dimensions:
Width: 400 mm
Height: 900 mm
Depth: 600 mm
IFU-TL HR GB.fm Page 2 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
GB 3
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
1.Safety instructions
The washing machine is appropriate for indoor
use only.
Do not store flammable fluids near the appliance.
Do not place electrical appliances on the lid of
your washing machine.
Children must be supervised to ensure that they
do not play with the appliance.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Do not attempt to force the lid open.
If necessary, the power cable may be replaced
with an identical one obtained from our After-
Sales Service. The power cable must only be
replaced by a qualified technician.
2.Packing
The packaging materials are 100% recyclable and
bear the recycling symbol . Adhere to local
regulations when disposing of packaging material.
3.Disposing of packaging and old washing
machines
This appliance is marked according to the
European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment.
Disposal must be carried out in accordance with
local environmental regulations for waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where you
purchased the product.
The washing machine is built from reusable
materials. It must be disposed of in compliance
with current local waste disposal regulations.
Before scrapping, cut off the power cable so that the
washing machine cannot be connected to the mains.
Remove detergent from compartment if you
intend scrapping your washing machine.
4.Energy saving tips
Achieve the best use of energy, water, detergent
and time by using the recommended maximum
load size.
Do not exceed the detergent dosages indicated
in the manufacturer’s instructions.
The Eco Ball - a special system in the outlet - will
prevent detergent loss from the drum to avoid
detergent loss into the environment.
Use “Prewash” (if available on your model) for
heavily soiled laundry only! Save detergent, time,
water and energy consumption by not selecting
“Prewash” for slightly to normally soiled laundry.
Pretreat stains with stain remover or soak dried
in stains in water before washing to reduce the
necessity of a hot wash program.
Save energy by using a 60° C instead of a 95° C
wash programme or a 40° C instead of a 60° C
wash programme.
Save energy and time by selecting a high spin
speed to reduce the water content in laundry
before using a tumble dryer (for machines with
adjustable spin speed).
5.General recommendations
Do not leave the washing machine connected
when not in use. Turn off the tap.
Before cleaning or carrying out maintenance
switch off the washing machine and disconnect it
from the mains supply.
6.EC Declaration of Conformity
This washing machine has been designed,
constructed and distributed in compliance with
the safety requirements of EC Directives:
2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility
Directive
IFU-TL HR GB.fm Page 3 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
GB 4
DESCRIPTION OF THE WASHING MACHINE
BEFORE THE FIRST WASH CYCLE
1.
Lid
2.
Detergent dispenser
3.
Drum
4.
Pump access behind filter
5.
After-Sales Service sticker (behind the
filter cover)
6.
Mobility lever (depending on model)
To move the washing machine: pull
the handle out a little bit by hand and
pull it out to the stop with the foot.
7.
Adjustable feet
To remove any residual water used in testing by the manufacturer, we recommend that you carry out a
short wash cycle without laundry.
1.
Open the tap.
2.
Close the drum flaps.
3.
Pour a small amount of detergent (about 30 ml) into the main wash chamber of the detergent
dispenser.
4.
Close the lid.
5.
Select and start a short programme (see separate programme chart).
1
2
3
4
5
7
6
IFU-TL HR GB.fm Page 4 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
GB 5
PREPARATION OF THE WASHING
Sort the laundry
1. Sort the laundry according to…
Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics,
wool, handwash items.
Colour
Separate whites and coloureds.
Wash new coloured items separately.
•Size
Wash items of different sizes in the same load to
improve washing efficiency and distribution in the
drum.
Fabric delicacy
Wash delicate articles separately: use a special
programme for Pure New Wool , curtains
and other delicates. Always remove curtain glides
or wash curtains with the glides inside a cotton
bag. Use the special programme for handwash
fabrics. Wash stockings, belts and other small
items or articles with hooks (e.g. bras) in special
cotton bags for washing machines or in zipped
pillow cases.
2.Empty pockets
Coins, safety pins and similar items can damage
your laundry as well as the washing machine’s
drum and tub.
3.Fasteners
Close zips and fasten buttons or hooks; loose
belts or ribbons should be tied together.
Stain removal
Blood, milk, egg and other organic substances are
generally removed by the enzyme phase of the
programme.
To remove red wine, coffee, tea, grass and fruit
stains etc. add a stain remover to the main wash
chamber of the detergent dispenser.
Particularly stubborn stains should be treated
before the wash.
Dyeing and bleaching
Only use dyes and bleaches that are suitable for
washing machines.
Follow the manufacturer’s instructions.
Plastic and rubber parts of the machine may be
stained by dyes or bleaches.
IFU-TL HR GB.fm Page 5 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
GB 6
Loading the laundry
1.
Open the machine lid by pulling it upwards.
2.
Open the drum by pushing the drum flap release
(pictures “
1a
” or “
1b
” - depending on the model;
models as shown on “
1a
” have a fixed drum flap
release which will not compress when pushed).
3.
Place the items of laundry into the drum one by one.
Do not exceed the maximum load of the programmes
indicated in the separate programme chart.
Notes:
- Overloading the machine will result in unsatisfactory
washing results and creased laundry.
- Take care that the laundry does not overhang the
drum; if this is the case, push the laundry down into
the drum so that there is enough free space to close
the drum flaps properly.
- Do not use the flaps to push the laundry into the
drum.
4.
To close the drum, hold both doors in the middle again
(picture “
2
”).
ATTENTION:
make sure that the drum flaps are
properly locked - depending on the model:
- the metal hook must be completely hooked into the
rear door flap - see picture “
2a
”, or
- all metal hooks must be properly hooked inside the
rear door flap, and the button must overlap the edge
of the rear door flap - see picture “
2b
”.
- check that no laundry gets stuck between the flaps,
or between flaps and drum.
2
1b
1a
2a
IFU-TL HR GB.fm Page 6 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
GB 7
DETERGENTS AND ADDITIVES
Choice of the right detergents and
additives
The type of detergent depends on:
type of fabric (cottons, easy care/synthetics,
delicate items, wool).
Note:
use only specific detergents for wool and
garments made of microfibres (like sports or
swimwear).
colour;
washing temperature;
degree and type of soiling.
Notes:
Do not use liquid detergents when activating the
“Start Delay” function (if available on your
machine).
Do not use liquid detergent for the main wash
when activating the “Prewash” option or
selecting a programme with “Prewash” (if
available on your model).
Whitish residues on dark fabrics are caused by
insoluble detergents components used in
modern phosphate-free powder detergents. If
you notice this problem, shake or brush the
affected items or use liquid detergents.
Keep detergents and additives in a safe, dry place
out of the reach of children.
Use only detergents and additives specifically
produced for domestic washing machines.
If you use descaling agents, dyes or bleaches,
make sure that they are suitable for washing
machine use.
Descaler could contain components that can
damage parts of your washing machine.
Do not use solvents (turpentine, benzine, etc.).
Do not machine wash fabrics that have been
treated with solvents or flammable liquids.
Dosage
Follow the instructions on the detergent pack in
relation to:
the degree and type of soiling;
the size of the load;
-
full load: follow the detergent manufacturer’s
instructions;
-
half load: 3/4 the amount used for a full load;
-
minimum load (about 1 kg): half the amount
used for a full load;
water hardness in your area (ask for information
from your water company): soft water requires
less detergent than hard water.
Notes:
Too much detergent can result in excess foam
formation, and the reduction of washing efficiency.If
the washing machine detects excessive foam it
may prevent spinning.
Insufficient detergent may result in:
grey laundry, deposits on the drum, tub and
heater.
When using concentrated fabric softeners, add
water in the detergents dispenser up to “MAX”
level mark.
To prevent dispensing problems when using
highly concentrated powder and liquid
detergents, use the special detergent ball or bag
supplied with the detergent and place it inside
the drum.
IFU-TL HR GB.fm Page 7 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
GB 15
AFTER-SALES SERVICE
Before contacting After-Sales Service:
1.
Try to remedy the problem yourself (see
“Troubleshooting Guide”).
2.
Restart the programme to check whether the
problem has solved itself.
3.
If the machine continues to function incorrectly,
call After-Sales Service.
Specify:
The nature of the problem.
The exact model of the washing machine.
The service code (number after the word
SERVICE).
The After-Sales Service sticker is situated
behind the filter cover or on the rear of the
machine.
Your full address.
Your telephone number and area code.
As a priority, you should contact the After-Sales
Service of the retailer who supplied you with the
washing machine.
TRANSPORT AND HANDLING
1.
Unplug the washing machine.
2.
Turn off the tap.
3.
Remove the water supply and drain hose.
4.
Eliminate all water from the hoses and the washing machine
(see “Cleaning the Filter/ Draining Residual Water”).
Wait for the water to cool so as to avoid any accidents.
5.
To facilitate moving the machine, pull the handle situated at
the bottom front (if available on your model) out a little by
hand and pull it out to the stop with the foot. Afterwards
push the handle back into the original stable position.
6.
Fix the transport bracket again for transportation.
7.
Transport the washing machine upright.
IMPORTANT:
Do not use the washing machine while the
handle is pulled out.
IFU-TL HR GB.fm Page 15 Friday, November 7, 2008 2:30 PM
Black process 45.0° 100.0 LPI
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ignis AWH 735 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ignis AWH 735 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Ignis AWH 735

Ignis AWH 735 Gebruiksaanwijzing - Nederlands - 18 pagina's

Ignis AWH 735 Gebruiksaanwijzing - Deutsch - 18 pagina's

Ignis AWH 735 Gebruiksaanwijzing - Français - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info