12784

Icom IC-T2H Handleiding

48
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
INSTRUCTION MANUAL
iT2H
144 MHz FM TRANSCEIVER
This device complies with Part 15 of the FCC rules. Operation is sub-
ject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page A (1,1)
ii
IMPORTANT
READ ALL INSTRUCTIONS carefully and com-
pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL—This in-
struction manual contains important operating instructions for
the IC-T2H.
EXPLICIT DEFINITIONS
The explicit definitions below apply to this instruction manual.
CAUTIONS
RWARNING! NEVER hold the transceiver so that the
antenna is very close to, or touching exposed parts of the
body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm
(2 to 4 in) away from the lips and the transceiver is vertical.
RWARNING! NEVER operate the transceiver with a
headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume op-
eration. If you experience a ringing in your ears, reduce the
volume or discontinue use.
NEVER connect the transceiver to an AC outlet or to a
power source of more than 16 V DC. Such a connection will
damage the transceiver.
NEVER connect the transceiver to a power source that is
DC fused at more than 5 A. Accidental reverse connection will
be protected by this fuse, higher fuse values will not give any
protection against such accidents and the transceiver will be
ruined.
NEVER attempt to charge alkaline or dry cell batteries. Be-
ware that external DC power connections will charge batteries
inside the battery case. This will damage not only the battery
case but also the transceiver.
WORD DEFINITION
RWARNING
Personal injury, fire hazard or electric
shock may occur.
CAUTION
Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page ii (1,1)
iii
DO NOT push the PTT when not actually desiring to trans-
mit.
Place unit in a secure place to avoid inadvertent use by chil-
dren.
DO NOT operate the transceiver near unshielded electri-
cal blasting caps or in an explosive atmosphere.
AVOID using or placing the transceiver in direct sunlight or
in areas with temperatures below –10°C (+14°F) or above
+60°C (+140°F).
The use of non-Icom battery packs/chargers may impair
transceiver performance and invalidate the warranty.
Even when the transceiver power is OFF, a slight current still
flows in the circuits. Remove the battery pack or case from
the transceiver when not using it for a long time. Otherwise,
the battery pack or installed Ni-Cd batteries will become ex-
hausted.
For USA only:
Caution: Changes or modifications to this transceiver, not ex-
pressly approved by Icom Inc., could void your authority to
operate this transceiver under FCC regulations.
SUPPLIED ACCESSORIES
Accessories included with the transceiver:
➀ Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
➁ Belt clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
➂ Battery case (BP-194)
with 8 Ni-Cd (AA) batteries* installed . . . . . . . . . . . . . . . 1
➃ Wall charger* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
*Not supplied with some versions.
➀
➂
➁
➃
IC-T2H_RTTE.qxd 03.6.20 18:57 Page iii (1,1)
iv
IMPORTANT ................................................................................................... ii
EXPLICIT DEFINITIONS ................................................................................ ii
CAUTIONS ..................................................................................................... ii
SUPPLIED ACCESSORIES ........................................................................... iii
TABLE OF CONTENTS ................................................................................. iv
1 ACCESSORY ATTACHMENT ................................................................... 1
2 PANEL DESCRIPTION ......................................................................... 2–7
■ Switches, controls, keys and connectors ............................................... 2
■ Customizable keys ................................................................................. 5
■ Custom key assignment ........................................................................ 5
■ Function display ..................................................................................... 6
3 BATTERY PACKS ............................................................................... 8–10
■ Battery pack charging ............................................................................ 8
■ Charging precautions ............................................................................. 8
■ About battery packs ............................................................................... 8
■ Charging connections ............................................................................ 9
■ Installing batteries in the battery case ................................................. 10
4 BASIC OPERATION ..........................................................................11–14
■ Power ON ............................................................................................. 11
■ Setting a frequency .............................................................................. 11
■ Dial select function ............................................................................... 12
■ Receive and transmit ........................................................................... 12
■ Selecting a memory channel ............................................................... 13
■ Lock function ........................................................................................ 13
■ Notes for set mode .............................................................................. 14
■ Setting tuning steps ............................................................................. 14
5 REPEATER OPERATION ................................................................. 15–18
■ General ................................................................................................ 15
■ Subaudible tones ................................................................................. 16
■ Offset frequency ................................................................................... 16
■ Auto repeater function ......................................................................... 17
6 MEMORY/CALL PROGRAMMING ................................................... 19–21
TABLE OF CONTENTS
■ General ................................................................................................ 19
■ Programming a memory channel ......................................................... 19
■ Programming the call channel ............................................................. 20
■ Memory editing .................................................................................... 21
7 DTMF MEMORY ............................................................................... 22–23
■ Programming a DTMF code ................................................................ 22
■ Transmitting a DTMF code .................................................................. 22
■ DTMF transmission speed ................................................................... 23
8 SCAN OPERATION .......................................................................... 24–25
■ Scan types ........................................................................................... 24
■ Programmed scan ............................................................................... 25
■ Memory (skip) scan ............................................................................. 25
9 SUBAUDIBLE TONE OPERATION .................................................. 26–27
■ Tone squelch ........................................................................................ 26
■ Tone scan ............................................................................................ 27
■ Pocket beep operation ......................................................................... 27
10 OTHER FUNCTIONS ........................................................................ 28–32
■ Initial set mode ..................................................................................... 28
■ Resetting the CPU ............................................................................... 30
■ Key customize mode ........................................................................... 31
■ Guide function ...................................................................................... 31
11 ANI OPERATION .............................................................................. 33–35
■ ANI mode ON ...................................................................................... 33
■ General ................................................................................................ 33
■ Operation ............................................................................................. 34
12 CLONING ................................................................................................ 36
13 TROUBLESHOOTING ............................................................................ 37
14 SPECIFICATIONS ................................................................................... 38
15 OPTIONS ................................................................................................ 39
16 MODE ARRANGEMENT .................................................................. 40–41
17 CE ...................................................................................................... 42–43
IC-T2H_RTTE.qxd 03.6.20 18:57 Page iv (1,1)
1
1
ACCESSORY ATTACHMENT
D Antenna
Connect the supplied flexible antenna to the antenna con-
nector and rotate the antenna clockwise.
u CAUTION: Transmitting without an antenna may
damage the transceiver.
D Belt clip
To attach:
Slide the belt clip into the plastic loop on the back of the
battery case/pack.
To remove:
Push the top of the belt clip towards the transceiver and at
the same time, push it downwards and free of the plastic
loop.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 1 (1,1)
2
2
PANEL DESCRIPTION
q
w
e
r[ANTENNA]
t[CHARGE]
y[TX]
u
o[DIAL SELECT]
!9
!0-!7
[CUSTOMIZABLE
KEYS]
i
!8
@0
[SP/MIC]
[PWR/VOL]
[PTT]
[UP/DOWN]
[MONITOR]
[GUIDE]
[DIGIT KEYS]
[MHz KEY]
12
5
8
0
4
79
6
3
SQL
SC
DUP
A V
B M
C T
D L
H/L
!7
u
!0
@0 !9
!8
!4
!2
o
y
!1
!5
!6
!3
i
■ Switches, controls, keys and connectors
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 2 (1,1)
connect the BC-110A/D/V wall charger for charging.
u CAUTION: This connection is for charging only. Power
to the transceiver must be turned off during charging.
y TX INDICATOR [TX] (p. 12)
Lights red while transmitting.
u UP/DOWN KEY [Y]/[Z]
➥ In VFO mode, increment or decrement the dis-
played frequency according to the set tuning
steps. (p. 11)
➥ In memory mode, increment or decrement the
selected memory channel. (p. 13)
➥ In initial set mode, select item conditions. (p. 28)
i MONITOR KEY [ (MONI)] (p. 13)
➥ Push and hold this switch to force the squelch
open; release to close it again.
➥ Push twice to keep the squelch open; push
again to close it.
➥ While pushing [PTT], push this switch to trans-
mit a 1750 Hz tone signal. (Europe version only)
➥ When a digit is mistakenly input, push [ ] and
input from the beginning.
o DIAL SELECT KEY [t] (p. 12)
Push this switch one or more times to select the
dial select step for frequency tuning.
3
2
PANEL DESCRIPTION
q PTT SWITCH [PTT] (p. 12)
Push and hold to transmit; release to receive.
w POWER/VOLUME CONTROL [PWR/VOL]
➥ Rotate to turn power on and off.
➥ Rotate clockwise to increase volume and counterclock-
wise to decrease volume.
e EXTERNAL SPEAKER AND MICROPHONE JACKS
[SP/MIC]
Connect an optional speaker-microphone or headset, if de-
sired. The internal microphone and speaker will not func-
tion when either is connected. (See p. 37 for options.)
D External connection
☞
NOTE: When connecting or disconnecting an external
speaker-microphone, first turn off power to the transceiver.
r ANTENNA CONNECTOR (p. 1)
Connects the supplied antenna.
t EXTERNAL DC POWER JACK [CHARGE]
Connect a 13.5 to 16 V DC power source using optional
cables, CP-12L or OPC-254L, to charge the batteries, or
This connection
does not apply
when a conden-
sor microphone
is connected.
Remote Audio out
(8 Ω)
[SP]
MIC
5 V
PTT
[MIC]
Audio input
PTT
33 kΩ
(2 kΩ)
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 3 (1,1)
1
D L
C T
B M
A V
H/L
DUP
SC
SQL
0
4
2
PANEL DESCRIPTION
!0 SQUELCH KEY [SQL]*
➥ Push [SQL], then push [Y]/[Z] one or more
times to select squelch level. “AUto”, “Sql 1” to
“Sql 8” are available to suit personal preferences
and operating conditions. (p. 13)
!1 SCAN START/STOP KEY [SC]*
➥ Push [SC] to start the scan. (p. 25)
• To change the scan direction, push [Y] or [Z].
➥ Push [SC] again to stop the scan. (p. 25)
!2 DUPLEX KEY [DUP]*
➥ Push once to select – DUP or twice to select
DUP mode. (p. 15)
!3 POWER SELECT KEY [H/L]*
➥ Push to toggle high and low power output. (p.
12)
•“LOW” appears when low power is selected.
!4 VFO/MEMORY KEY [A V]*
➥ Push to toggle VFO mode and memory mode.
(p. 11)
•“X” appears when memory mode is selected.
➥ Push for 1 sec. to enter “Set mode”. (p. 14)
➥ Transmits an “A” for DTMF operation while
pushing [PTT].
!5 MEMORY WRITE KEY [
B M]*
➥ Push [
B M], then select a memory channel num-
ber with [Y]/[Z].
➥ Push [
B M] for 1 sec. to program the information
into the memory channel. (p. 19)
➥ Transmits a “B” for DTMF operation while push-
ing [PTT].
!6 TONE SETTING KEY [
C T]*
➥ Toggles tone squelch operation ON/OFF.
•“T”, “TSQL” or “TSQL” appears on the display.
➥ Transmits a “C” for DTMF operation while push-
ing [PTT].
!7 LOCK KEY [
D L]*
➥ Toggles the lock function ON/OFF. (p 13)
➥ Transmits a “D” for DTMF operation while push-
ing [PTT].
!8 GUIDE KEY [#] (p. 31)
➥ Activates the guide function.
➥ Transmits an “F” for DTMF operation while
pushing [PTT].
!9 DIGIT KEYS
➥ Input the specified digit during frequency input,
memory channel selection, etc.
➥ Transmit the DTMF code of the specified digit
while pushing [PTT].
@0 MHz KEY [M] (p. 12)
➥ Used as a short cut for inputting frequencies.
➥ Transmits an “E” for DTMF operation while
pushing [PTT].
to
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 4 (1,1)
5
2
PANEL DESCRIPTION
■ *Customizable keys
[SQL], [SC], [DUP], [H/L], [A V], [B M], [
C T], [D L]
These keys can be assigned a variety of functions (see p. 32
for a list of available functions).
NOTE: In this manual, the customized keys are represented
by the “
f
” icon. Operations which require a customizable key
observe the following style—
Push [
f
(FUNCTION)]
where “
f
” indicates the key is customized and “FUNCTION”
indicates the assigned function e.g. TONE, etc.
D Guide function (p. 31)
The guide function displays the function of keys and switches
quickly and easily.
Once a key function has been changed from its default, the
guide function is a convenient way to determine its function.
Key Default
Your
Assignment
[Y]UP fixed
[Y] DOWN fixed
[t] MONI fixed
[ ] DIAL SELECT fixed
[SQL] SQUELCH
[SC] SCAN
[DUP] DUPLEX
[H/L] HI/LO
[0]–[9] NUMERAL INPUT fixed
[
A V] V/m
[
B M] SmW
[
C T] TONE
[
D L] LOCK
[#] MHz KEY fixed
[
M
] GUIDE KEY fixed
■ Custom key assignment
Write down your key assignments for reference.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 5 (1,1)
t ANI INDICATOR (p. 33)
Appears when the transceiver is set to ANI (Automatic
Number Identification) operation mode.
y LOW BATTERY INDICATOR
➥ Appears when the battery is nearing exhaustion.
➥ Appears and flashes when battery replacement is nec-
essary.
u FREQUENCY READOUT
➥ In frequency indication mode, indicates the operating
frequency. (p. 11)
• The smaller “75,” “50” and “25” to the right of the readout in-
dicates 7.5, 5.0 and 2.5 kHz, respectively.
➥ In channel indication mode, indicates the selected chan-
nel. (p. 11)
6
2
PANEL DESCRIPTION
■ Function display
q MEMORY MODE INDICATOR (p. 13)
Appears while in memory mode.
w LOCK INDICATOR (p. 13)
Appears while the lock function is activated.
e DUPLEX INDICATOR (p. 15)
Appears during semi-duplex operation.
•“–DUP” appears for minus duplex; “DUP” appears for plus du-
plex.
r TONE INDICATORS
“T” appears when the subaudible tone encoder (p. 16) is in
use; “T SQLS” appears during pocket beep operation
(p. 27) and “T SQL” appears when the tone squelch func-
tion (p. 26) is activated.
MR
DUP
SKIP
LOW
T SQL
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 6 (1,1)
7
2
PANEL DESCRIPTION
➥ In set mode or initial set mode, indicates the selected
item, condition, etc.
i BUSY AND S/RF INDICATORS (p. 12)
➥ “BUSY” appears when receiving a signal or when the
squelch is open.
➥ The S/RF indicators show the relative signal strength
while receiving and the output power when transmitting
(2 segments appear for low power and all segments ap-
pear for high power).
o LOW POWER INDICATOR (p. 12)
Appears when low output power is set.
!0 SKIP INDICATOR (p. 25)
Appears when the selected channel is set as a “skip” chan-
nel.
!1 MEMORY CHANNEL INDICATOR (p. 13)
Indicates the selected memory channel and other items
such as the call channel.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 7 (1,1)
8
3
BATTERY PACKS
■ Battery pack charging
The supplied BP-194
BATTERY CASE
includes rechargeable
Ni-Cd batteries* and can be charged approx. 300 times.
Charge the batteries before first operating the transceiver or
when they become exhausted.
If you want to be able to charge the batteries more than 300
times, the following points should be observed:
1. Avoid overcharging. The charging period should be less
than 48 hours.
2. Use the batteries until they become completely exhausted
under normal conditions. We recommend battery charging
just after transmitting becomes impossible.
*Not supplied with some versions.
■ Charging precautions
NEVER attempt to charge dry cell/alkaline batteries. This will
cause internal liquid leakage and damage the battery case
and transceiver.
NEVER connect two or more chargers at the same time.
Charging may not occur under temperatures of 10°C (50°F)
or over temperatures of 40°C (104°F).
■ About battery packs
D Operating period
Depending on installed battery pack (batteries), the operating
period of the transceiver varies. Refer to p. 39 for operating
period details.
D Battery life
If your batteries seem to have no capacity even after being
fully charged, completely discharge them by leaving the
power ON overnight. Then fully charge them again.
If the batteries still do not retain a charge (or very little), new
batteries must be purchased.
Recycling information (USA only)
The product that you purchased contains a
rechargeable battery. The battery is recyclable. At
the end of its useful life, under various state and
local laws, it may be illegal to dispose of this battery into the
municipal waste stream. Call 1-800-8-BATTERY for battery
recycling options in your area or contact your dealer.
RBRC
RBRC
Ni-
Cd
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 8 (1,1)
9
3
BATTERY PACKS
■ Charging connections
D Regular charging
When charging a battery case (pack) attached to the trans-
ceiver the power must be OFF.
D Rapid charging with the BC-119
The optional BC-119 provides rapid charging of optional
Ni-Cd battery packs (power to the transceiver must be OFF
during charging). The following are additionally required:
• AD-81
• An AC adapter (may be supplied
with the BC-119 depending
on version).
Transceiver with
attached
battery case
(pack)
BC-110A/D/V*
CP-12L
(optional)
OPC-254L
(optional)
To a 13.5
to 16 V DC
power source
To
[CHARGE]
white
black
Charging periods:
15 hours (w/BP-195)
20 hours (w/BP-196)
Charging periods:
1 hour (w/BP-195)
1.5 hours (w/BP-196)
*Not supplied with some versions.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 9 (1,1)
10
3
BATTERY PACKS
■ Installing batteries in the
battery case
When using a battery case attached to the transceiver, install
8 AA(R6) size Ni-Cd or alkaline batteries as illustrated below.
➀ Remove the bat-
tery case from the
transceiver.
➁ Install 8 × R6(AA)
size Ni-Cd or alka-
line batteries.
• Be sure to observe
the correct polarity.
● NEVER connect DC power to the transceiver when in-
stalling dry cell or alkaline batteries. Such a connection will
damage the transceiver.
● Be careful of battery overcharging. When operating via ex-
ternal DC power, installed batteries are simultaneously
charged.
● Keep battery contacts clean. It’s a good idea to clean bat-
tery terminals once a week.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 10 (1,1)
11
4
BASIC OPERATION
■ Setting a frequency
D Via the keypad
➀ Push [A V] to select VFO mode, if
necessary.
➁ Push 6 digit keys, starting from
the 100 MHz digit, to input a fre-
quency.
• Push the [M] key first to start input
from the 100 kHz digit, if desired.
• When a digit is mistakenly input,
push [ ] and input from the begin-
ning.
•“2” and “7” are acceptable for the 1
kHz digits (depending on the 10 kHz digit).
D Using the [Y]/[Z] keys
Each push increments/decrements the frequency according
to the selected tuning step (see right), except when the 100
kHz or 1 MHz dial select step is selected (see following
page). When a dial select step is selected, each push incre-
ments/decrements the frequency either 100 kHz or 1 MHz.
■ Power ON
Rotate [PWR/VOL] clockwise
to turn power ON.
D Toggling frequency/channel
indication mode
Channel indication mode is used to simplify operation. In this
mode only pre-programmed memory channel numbers are
displayed and functions are limited ([PWR/VOL], [
D L], [PTT],
[ ], [H/L] and [SC] are functional).
To toggle between the indication modes:
While pushing [Z] + [0], rotate [PWR/VOL] to turn power ON.
Frequency indication Channel indication
at power ON
0
AT
POWER ON
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 11 (1,1)
12
4
BASIC OPERATION
■ Dial select function
Use the dial select function to adjust the tuning behaviour or
the [Y]/[Z] keys—use 1 MHz tuning when you want to
change the frequency in large increments; use the selected
tuning step when you want to change the frequency in smaller
increments.
➀ Push [t] one or more times to
select the desired [Y]/[Z] key
tuning increment.
• 1 MHz tuning, 100 kHz tuning or
regular tuning steps can be selected
(see diagram at right).
➁ Release [t] to return to normal operation.
■ Receive and transmit
➀ Rotate [PWR/VOL] clockwise to turn power ON.
➁ Adjust volume to the desired level.
• While pushing [ ], rotate [VOL].
➂ Set a frequency.
When a signal is received:
➥ Squelch opens and audio is emitted from the speaker.
➥ “BUSY” appears and the S/RF indicator shows the relative sig-
nal strength.
➃ Push [H/L] to toggle output power between high and low.
•“LOW” appears when low output power is selected.
➄ Push and hold [PTT] to transmit; then speak into the mi-
crophone.
• Do not hold the microphone too close to your mouth or speak
too loudly. This may distort the signal.
• The TX indicator lights red.
• The S/RF indicator shows the output power selection.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 12 (1,1)
13
4
BASIC OPERATION
✔ Convenient
Monitor function: Push and hold [ ] to listen to weak sig-
nals that do not open the squelch; or push [ ] twice to mon-
itor a signal without having to continuously hold [ ].
Squelch control: The transceiver employs a noise pulse
count system and therefore, squelch is adjusted automatically
when “AUto” is selected for the squelch level:
Push [SQL], then push [Y]/[Z] one or more times until “AUto”
appears. Manual levels from “Sql 1” to “Sql 8” are also avail-
able to suit personal preferences and operating conditions.
■ Selecting a memory channel
➀ Push [A V] to select memory chan-
nel mode, if necessary.
•“X” appears.
➁ Push 2 digit keys to select the de-
sired memory channel (or push the
[Y]/[Z] keys).
• The first nine memory channels are
preceded by a “0.”
• When you want to select scan edge
channels PA or Pb, push [4], [1] or [4],
[2], respectively.
■ Lock function
The lock function prevents accidental frequency changes and
accidental function activation. By default, [
D L] toggles this
function on and off.
Push [
D L] for 1 sec. to toggle the function on and off.
•“é” appears while the lock func-
tion is activated.
• [PTT], [PWR/VOL] and [ ]can be
used regardless of this setting.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 13 (1,1)
14
4
BASIC OPERATION
■ Notes for “Set mode”
The following items can be set from VFO mode.
Set mode items:
Tuning steps (p. 14)
Duplex setting (p. 15)
Repeater tones (p. 16)
Offset frequency (p. 16)
Subaudible tones (p. 16)
Call channel (p. 20)
CTCSS tones (p. 26)
When setting items from memory mode, input data will dis-
appear when changing memories or turning power OFF.
Please select VFO mode before entering set mode, and read
the instructions for each set mode item carefully.
To turn set mode ON and OFF:
➀ Push [A V] or [
f
(CALL)]* for 1 sec. to enter set mode.
➁ Push [t] one or more times to select the item.
➂ Push the [Y/Z] keys to select the desired value.
➃ Push [A V] or [
f
(CALL)]* to exit set mode.
■ Setting tuning
steps
The transceiver has 8 tuning steps as follows:
5 kHz 10 kHz 12.5 kHz 15 kHz
20 kHz 25 kHz 30 kHz 50 kHz
➀ Push [A V] or [
f
(CALL)]* for 1 sec. to enter set mode.
➁ Push [t] one or more times to select the tuning step item.
➂ Push the [Y/Z] keys to select the desired tuning step.
➃ Push the same key used in step ➀ above to enter the tun-
ing step and exit set mode.
For convenience, select a tuning step that matches the fre-
quency intervals of repeaters in your area.
*☞NOTE:
Selecting a tuning step is possible using one of the pro-
grammable key/switches when this function is assigned
using key customize mode (p. 31). In this case, pushing
[
f
(tS)] enters tuning step mode.
When pushing [ ] to exit set mode, any changes made
while in set mode are cancelled.
USING
SET MODE
This display shows that a tuning step of 25
kHz is selected.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 14 (1,1)
15
5
REPEATER OPERATION
■ General
When using a repeater, the transmit frequency is shifted from
the receive frequency by the offset frequency. It is convenient
to program repeater information into memory channels (p.
19).
➀ Set the receive frequency (repeater output frequency).
➁ Push [DUP] one or more times to select –DUP or DUP.
•“–DUP” indicates the transmit frequency is shifted down; “DUP”
indicates the transmit frequency is shifted up.
• When the auto repeater function is in use (USA version only) this
selection and step ➂ are not necessary (p. 17).
➂ Push [C T] to activate the subaudible tone encoder, ac-
cording to repeater requirements.
•“T” appears.
• Refer to the table of subaudible tone frequencies on the following
page.
➃ Push and hold [PTT] to transmit.
• The displayed frequency automatically changes to the transmit
frequency (repeater input frequency).
• If “oFF” appears, check the offset frequency (p. 16).
➄ Release [PTT] to receive.
➅ Push and hold [ ] to check whether the other station’s
transmit signal can be directly received or not.
D Tone information
Some repeaters require a tone to be accessed. In this case,
precede step ➃ at left with the required tone.
DTMF TONES
While pushing [PTT], push the desired digit key(s) to transmit
DTMF tones.
• The transceiver has 5 DTMF memory channels. See p. 22 for de-
tails.
1750 Hz TONE (European version only)
While pushing [PTT], push and hold [ ] for 1 to 2 sec. to
transmit a 1750 Hz tone signal.
✔ Convenient
Tone scan function: When you don’t know the subaudible
tone used for a repeater, the tone scan is convenient for de-
tecting the tone frequency.
Push and hold [SC] to activate the tone scan. See p. 27 for
more details.
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 15 (1,1)
16
5
REPEATER OPERATION
■ Subaudible tones
Some repeaters require subaudible tones to be accessed.
Subaudible tones are superimposed over your normal signal
and must be set in advance.
➀ Push [A V] for 1 sec. to enter set mode.
➁ Push [t] one or more times until
“RP” appears.
➂ Push [Y]/[Z] to select the desired
subaudible tone.
➃ Push [A V] to enter the selected
tone and exit set mode.
When set mode is selected from memory mode:
➄ Push [B M].
➅ Push [A V].
➆ Push [B M] for 1 sec.
Available subaudible tone frequencies (unit: Hz)
67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1
69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6
71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8
74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3
77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1
USING
SET MODE
■ Offset frequency
When communicating through a repeater, the transmit fre-
quency is shifted from the receive frequency by an amount
determined by the offset frequency.
➀ Push [A V] for 1 sec. to enter set mode.
➁ Push [t] one or more times until
“oW” appears.
➂ Push [Y]/[Z] to select the desired
offset frequency.
• Selectable steps are the same as the
pre-set tuning steps.
➃ Push [A V] to enter the selected offset frequency and exit
set mode.
When set mode is selected from memory mode:
➄ Push [B M].
➅ Push [A V].
➆ Push [B M] for 1 sec.
USING
SET MODE
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 16 (1,1)
17
5
REPEATER OPERATION
■ Auto repeater
function (USA version only)
The USA version automatically activates the repeater settings
(duplex, ON/OFF, duplex direction, tone encoder ON/OFF)
when the operating frequency falls within or outside of the
general repeater output frequency range. The offset and re-
peater tone frequencies are not changed by the auto repeater
function, reset these frequencies, if necessary.
➀ While pushing [8] + [0], turn power on to enter initial set
mode.
➁ Push [t] one or more times until “AR” appears.
➂ Push [Y]/[Z] to select the desired condition.
•“oFF”—the auto repeater function is
turned off;
“on1”—the auto repeater function acti-
vates for duplex only;
“on2”—the auto repeater function acti-
vates for duplex and tone.
➃ Turn power off, then on again to exit initial set mode.
USING
INITIAL SET MODE
Frequency range and offset direction
FREQUENCY RANGE DUPLEX DIRECTION
145.200–145.495 MHz
“–DUP” appears
146.610–146.995 MHz
147.000–147.395 MHz “DUP” appears
IC-T2H_RTTE.qxd 03.6.20 18:57 Page 17 (1,1)
18
5
REPEATER OPERATION
WEATHER CHANNELS (USA version only)
There are 10 weather channels for monitor-
ing weather channels from the NOAA (Na-
tional Oceanographic and Atmospheric
Administration) broadcasts.
NOTE: The weather channel frequencies are out of the
guaranteed frequency range (see p. 38). Intermittent re-
ception and/or poor signal quality may occur depending on
conditions.
➀ Enter key customize mode (p. 31) and assign the
weather function to one of the keys, if necessary.
➁ Push [
f
(WX)] to select weather
channel mode.
•“WX” and the weather channel num-
ber appear.
➂ Push [Y]/[Z] to select the desired
weather channel.
NOTE: Weather channels appear in frequency indication
mode only.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 18 (1,1)
19
6
MEMORY/CALL PROGRAMMING
■ General
The transceiver has 40 memory channels (plus 1 pair of scan
edge channels and 1 call channel) for storage of often-used
frequencies. In addition, the USA version has 10 marine
weather channels (however, these are not programmable).
D Memory/call channel contents
The following information can be programmed into mem-
ory/call channels:
• Operating frequency
• Duplex direction (DUP or –DUP) with an offset frequency
(pgs. 15, 16)
• Subaudible tone encoder or tone squelch on/off (pgs. 15,
26)
• Subaudible tone and tone squelch frequencies (pgs. 15, 26)
• Skip information* (p. 25)
*Except for scan edge memory channels.
■ Programming a memory
channel
➀ Push [A V] to select VFO mode, if
necessary.
➁ Push 6 digit keys to enter the desired frequency.
➂ Push [DUP], [C T], etc. to set other
information as desired.
➃ Push [B M], then select a memory
channel number with [Y]/[Z].
➄ Push [B M] for 1 sec. to program
the information into the channel
and return to VFO.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 19 (1,1)
20
6
MEMORY/CALL PROGRAMMING
■ Programming the
call channel
➀ Push [
f
(CALL)] to select call
channel mode.
•“C” appears.
➁ Push [
f
(CALL)] for 1 sec. to enter
set mode.
➂ Push [t] one or more times until
“FR” appears.
➃ Push [6] digit keys to input the de-
sired frequency.
➄ If desired, push [t] again, then
push [Y]/[Z] to select another item
(e.g. tone setting) and condition.
➅ Repeat step ➄ until all desired in-
formation is programmed into the
call channel.
➆ Push [
f
(CALL)] to exit call channel set mode.
➇ Push [B M].
➈ Push [
f
(CALL)].
➉ Push [B M] for 1 sec.
USING
SET MODE
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 20 (1,1)
21
6
MEMORY/CALL PROGRAMMING
■ Memory editing
Memory (call) channel contents can be moved to VFO or to
another memory.
D Memory/call ➾ VFO
➀ Select the memory (call) channel to be transferred:
➥ Push [
A V] ([
f
(CALL)]) to select memory (call) mode.
➥ Push [Y]/[Z] to select the memory (call) channel.
➁ Push [B M] for 1 sec. to transfer the VFO contents to the
selected memory.
• VFO mode is selected.
D Memory/call ➾ memory/call
➀ Select the memory (call) channel to be transferred:
➥ Push [
A V] ([
f
(CALL)]) to select memory (call) mode.
➥ Push [Y]/[Z] to select the memory (call) channel.
➁ Push [B M] momentarily.
•“VF” appears and flashes with “X”.
➂ Push [Y]/[Z] to select the target memory.
➃ Push [B M] for 1 sec.
• VFO mode is selected and the contents are transferred to the tar-
get memory.
D Clearing a memory
➀ Push [B M] to enter memory transfer mode.
•“X” and a memory channel number flash.
➁ Push [Y]/[Z] to select the memory channel to be cleared.
• Memory channels PA, Pb and CH1 cannot be cleared.
➂ Push [B M] momentarily, then within
1 sec. push it again for 1 sec.
• The contents of the selected
memory are cleared.
➃ Push [ ] to return to regular operation.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 21 (1,1)
22
7
DTMF MEMORY
■ Programming a DTMF code
The transceiver has 5 DTMF memory channels (d1 to d5) for
storage of often-used DTMF codes of up to 32 digits.
➀ Push [
f
(DTMF)] to enter DTMF
memory.
• One of “d1” to “d5” appears.
➁ Push [Y]/[Z] to select the desired
channel.
➂ Push [
f
(DTMF)] for 1 sec. to enter
DTMF programming mode.
•“_____” appears.
• Programmed memories can be
cleared in this way.
➃ Push the digit keys to enter the desired DTMF code.
• A maximum of 32 digits can be input.
• If a digit is mistakenly input, push [ ] then repeat from step ➀.
➄ Push [
f
(DTMF)] to input the
digits and exit DTMF programming mode.
• A beep sounds.
■ Transmitting a DTMF code
D Using a DTMF memory channel
➀ Push [
f
(DTMF)] to enter DTMF memory mode.
➁ Push [Y]/[Z] to select a DTMF memory channel to trans-
mit.
➂ Push [
f
(DTMF)] to transmit the displayed DTMF memory.
• After the DTMF code is transmitted, the transceiver automatically
returns to normal operating mode.
D Manual DTMF code transmission
➀ While pushing [PTT], push digit keys to transmit a DTMF
code manually.
➁ Release [PTT] to return to receive.
✔ CONVENIENT
DTMF re-dial function: This function automatically re-trans-
mits the previously sent DTMF code. This is especially con-
venient when you want to re-transmit a manually transmitted
DTMF code.
Push [
f
(RE-DIAL)] to activate the function. See p. 31 to as-
sign this function to a switch, if necessary.
NOTE: Once the transceiver is turned off, any temporarily
memorized DTMF contents will be cleared.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 22 (1,1)
23
7
DTMF MEMORY
■ DTMF
transmission speed
When slow DTMF transmission speeds are required (as for
some repeaters), the transceiver’s rate of DTMF transmission
can be adjusted.
➀ While pushing [8] + [0], turn power on to enter initial set
mode.
➁ Push [t] one or more times until
“dt” appears.
➂ Push [Y]/[Z] to select the desired
DTMF transmission speed.
• Four speeds are available: “100” (100
msec. intervals) is the fastest; “500”
(500 msec. intervals) is the slowest.
➃ Turn power off, then on again to
exit initial set mode.
USING
INITIAL SET MODE
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 23 (1,1)
24
8
SCAN OPERATION
PROGRAMMED SCAN
Band
edge
Band
edge
Scan
Jump
Scan edges
PA P b
MEMORY (SKIP) SCAN
SKIP
SKIP
Mch 1
Mch 7
Mch 2 Mch 4
Mch 3 Mch 5 Mch 6
Mch 8
Mch 40 Mch 11 Mch 10 Mch 9
■ Scan types
D Scan resume condition
When a signal is received dur-
ing scanning, the scan resume
condition determines what ac-
tion the transceiver takes. The
IC-T2H has 2 scan resume
conditions available as illus-
trated at right. Use initial set
mode to select the one which
best suits your needs.
➀ While pushing [8] + [0], turn power on to enter initial set
mode.
➁ Push [t] one or more times until
“SC” appears.
➂ Push [Y]/[Z] to select the desired
scan resume condition.
• Pause scan: when receiving a signal,
scan pauses on the signal until it dis-
appears, then resumes.
Timer scan: when receiving a signal,
scan pauses on the signal for 10 sec.,
then resumes.
➃ Turn power off, then on again to exit initial set mode.
USING
INITIAL SET MODE
Pause
scan
Receiving
a signal
Timer
scan
10 sec.
2 sec.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 24 (1,1)
25
8
SCAN OPERATION
■ Programmed scan
Programmed scan repeatedly scans between two user-pro-
grammed frequencies (memory channels “PA” and “Pb”). This
scan is useful for checking for signals within a specific fre-
quency range such as repeater output frequencies, etc.
➀ Push [A V] to select VFO mode, if necessary.
➁ Push [SC] to start the scan.
• To change the scan direction, push [Y] or [Z].
➂ Push [SC] again to stop the scan.
NOTE: Scan edges, PA/Pb, must be programmed in ad-
vance (program them in the same manner as regular
memory channels—p. 19).
If the same frequencies are programmed into the scan
edges, programmed scan will not proceed.
■ Memory (skip) scan
Memory scan repeatedly scans all programmed memory
channels, except those set as skip channels.
➀ Push [A V] to select memory mode, if necessary.
•“X” appears.
➁ Push [SC] to start the scan.
• To change the scan direction, push [Y] or [Z].
➂ Push [SC] again to stop the scan.
D Setting skip channels
In order to speed up the scan interval, you can set memory
channels you don’t wish to scan as skip channels.
➀ Push [A V] to select memory mode, if necessary.
•“X” appears.
➁ Push [Y]/[Z] to select a memory channel to set as a skip
channel.
➂ Push [SC] for 1 sec. to toggle the
skip setting on/off.
•“SKIP” appears when the channels is
set as a skip channel.
• If memory scan is accidentally started,
push [SC] to stop it.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 25 (1,1)
26
9
SUBAUDIBLE TONE OPERATION
■ Tone squelch
D Operation
The tone squelch opens only when receiving a signal con-
taining a matching subaudible tone. You can silently wait for
calls from group members using the same tone.
➀ Set the operating frequency.
➁ Set the desired subaudible tone in set mode.
• See right for programming.
➂ Push [C T] one or more times until “TSQL” appears.
➃ When the received signal includes a matching tone,
squelch opens and the signal can be heard.
• When the received signal’s tone does not match, tone squelch
does not open, however, the S-indicator shows signal strength.
• To open the squelch manually, push and hold [ ].
➄ Operate the transceiver in the normal way.
➅ To cancel the tone squelch, push [C T].
NOTE: The transceiver has 50 tone frequencies and con-
sequently their spacing is narrow compared to units hav-
ing 38 tones. Therefore, some tone frequencies may
receive interference from adjacent tone frequencies.
✔ CONVENIENT
Store subaudible tone frequencies and tone squelch on/off
settings in memories (call) for easy recall.
D Setting subaudible tones for
tone squelch operation (CTCSS tones)
Separate tone frequencies can be set for tone squelch oper-
ation than for repeater operation (the same range of tones is
available—see below). Like repeater tones, these are set in
set mode.
➀ Select VFO or a memory channel.
➁ Push [A V] for 1 sec. to enter set mode.
➂ Push [t] one or more times until
“Ct” appears.
➃ Push [Y]/[Z] to select the desired
subaudible tone.
➄ Push [A V] to program the selected tone and exit set mode.
When set mode is selected from memory mode:
➅ Push [B M].
➆ Push [A V].
➇ Push [B M] for 1 sec.
Available subaudible tone frequencies (unit: Hz)
67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1
69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6
71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8
74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3
77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1
USING
SET MODE
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 26 (1,1)
27
9
SUBAUDIBLE TONE OPERATION
■ Tone scan
The transceiver can detect the subaudible tone frequency in a
received signal. By monitoring a signal, such as that being
transmitted on a repeater input frequency, you can determine
the tone frequency required to access the repeater.
➀ Set the desired frequency or memory channel to be
checked for a tone frequency.
➁ Push [
f
(T-SCAN)] for 1 sec. to start the tone scan.
• Push [Y]/[Z] to change the scan direction.
➂ When the tone frequency is decoded, the set mode con-
tents are programmed with the tone frequency.
• The decoded tone frequency is used for the tone encoder or tone
encoder/decoder, depending on the tone squelch on/off setting.
•“Ct” (CTCSS—Continuous Tone Coded Squelch System) or “Rt”
(Repeater Subaudible Tone) appears during tone scan whether
the tone squelch is in use or not.
➃ Push [
f
(T-SCAN)] again to stop the scan.
■ Pocket beep operation
This function uses subaudible tones for calling and can be
used as a “common pager” to inform you that someone has
called you while you were away from the transceiver.
➀ Set the operating frequency.
➁ Set the desired subaudible tone (same as that used for
tone squelch operation, “Ct”) in set mode.
• See previous page for programming.
➂ Push [C T] two times until “TSQLS” appears.
➃ When a signal with a matched tone is received, the trans-
ceiver emits beep tones for 30 sec. and flashes “S.”
➄ Push [PTT] to answer or push [ ] to stop the beeps and
flashing.
• Tone squelch is automatically selected.
D Calling a waiting station using pocket beep
A subaudible tone matched with the station’s tone frequency
is necessary. Use the tone squelch on the previous page or
subaudible tone encoder (p. 15).
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 27 (1,1)
28
OTHER FUNCTIONS
■ Initial set mode
Initial set mode is accessed at power on and allows you to
set seldom-changed settings. In this way you can “customize”
transceiver operations to suit your preferences and operating
style.
D Entering initial set mode
➀ While pushing [8] + [0], rotate [PWR] to turn power on.
• The transceiver enters initial set mode and “mS SImP” or “mS
noRm” (see right) is displayed.
➁ Push [t] one or more times to select the desired display
as described on the following pages.
➂ Push [Y]/[Z] to select the desired condition.
➃ Turn power off, then on again to exit initial set mode and
select the previous operating mode.
D Message
When no operation is performed for 5 sec. in initial set mode,
a message scrolls across the function display prompting you
for input.
Q Message example
for microphone simple mode
AT
POWER ON
D Mic simple mode (Optional HM-75A required)
This item turns the microphone simple
mode on or off. Microphone simple
mode is used to change the function
assignments for switches on the op-
tional HM-75A
REMOTE CONTROL MI
-
CROPHONE
as below. This assignment
is convenient for 3-channel use of
simple operation.
*Functions only when in conversation mode.
NOTE:
Turn power off when connecting the HM-75A to the trans-
ceiver.
VFO mode cannot be selected via the microphone when
SIMPLE mode is selected.
NORMAL SIMPLE
Freq. CH
ANI
Freq. CH
ANI
HM-75A
indication indication indication indication
SWITCH
[CALL] NULL NULL [ ] [ ] [ ]*
[V/m] NULL NULL [CALL] NULL NULL
[UP] [UP] [UP] MCH01 MCH01 MCH01
[DOWN] [DOWN] [DOWN]
MCH02 MCH02 MCH02
A
B
10
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 28 (1,1)
29
10
OTHER FUNCTIONS
D Auto power OFF
This item allows you to set a time at
which the transceiver will automati-
cally turn OFF. The power OFF time
can be set to 20, 40, 60 min. or turned
off.
D LCD backlighting
When set to AUTO, display backlight-
ing automatically turns on when a key
is pushed; when set to OFF display
backlighting cannot be turned ON;
when set to ON display backlighting
remains ON continuously.
D Beep tones ON/OFF
Confirmation beep tones normally
sound when you push a key or switch.
These can be turned ON or OFF as
you prefer.
• When [BEEP] is assigned to one of the
keys (see p. 29), push this key to toggle
beep tones on/off without using initial set
mode.
D Auto repeater (U.S.A version only, see p. 17)
D Power saver
This item sets the power saver duty
cycle—the ratio of receive circuit on to
receive circuit off while standing by.
The duty cycle can be set to auto-
matic, 1:4 or OFF. Setting to auto-
matic conserves the most battery
power.
D DTMF speed (see p. 23)
D LCD contrast
This item sets the function display
contrast to one of two levels—“1” is
low contrast and “2” is high contrast.
AUTO Selects “1:4” duty ratio when receiving no signal
for 5 sec., then “1:8” 60 sec. after that.
1:4 Standby : 125 msec.
Circuit idle : 500 msec.
OFF No power saver function.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 29 (1,1)
30
10
OTHER FUNCTIONS
■ Resetting the CPU
Reset the CPU before operating the transceiver for the first
time, or when the internal CPU malfunctions.
➥ While pushing [A V] + [C T], turn
power on to reset the transceiver.
•“CLEAR” appears briefly to indicate
the CPU has been reset.
CAUTION: Resetting the CPU returns all programmed
contents to their default settings.
AT
POWER ON
D Scan resume condition (see p. 24)
D Active memory channels
This item allows you to adjust the
number of active memory channels.
Selectable values are 10, 20, 30 or
40.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 30 (1,1)
31
10
OTHER FUNCTIONS
■ Key customize mode
The functions of the [SQL], [SC], [DUP], [H/L], [A V], [B M], [C
T] and [D L] keys on the IC-T2H can be customized to suit
your operating needs.
➀ While pushing [#] + [0], turn power
on to enter key customize mode.
•“CUStom” appears.
➁ Push the key you wish to program.
• The key’s currently programmed func-
tion appears and scrolls across the
display.
➂ Push the [Y]/[Z] keys to select the
function you wish to assign to the
key.
• See the chart on the following page
for assignable functions.
➃ Push the same key as in step ➁ for 1 sec. to assign the
function to the key.
• If this step is not performed, the key will retain its previous func-
tion.
➄ Push another key to be programmed, if desired; or, turn
power off, then on again to exit key customize mode.
AT
POWER ON
■ Guide function
The guide function displays the functions of keys and
switches quickly and easily.
➀ Push [#] to activate the guide func-
tion.
•“GUIdE” appears in the display.
➁ Push and hold the key or switch
you want to know the function of.
• The key/switch name appears and its
assigned function scrolls across the
display.
➂ Release the key/switch pushed in the previous step to re-
turn to normal operation.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 31 (1,1)
32
10
OTHER FUNCTIONS
ASSIGNABLE FUNCTIONS
NULL
Backlight (LIGHT)
Power output ([H/L])
Scan start/stop ([SC])
DTMF memory*
1
(DTMF)
DTMF re-dial (RE-DIAL)
Lock function ([
D L])
Beep tones (BEEP)
VFO/memory ([
A V])
Tone setting ([
C T])
Tone scan (T SCAN)
Tuning step (TS)
Squelch level ([SQL])
WX channels*
2
(WX)
ANI code*
3
(ANI CODE)
Duplex setting ([DUP])
Memory write ([
B M])
Call channel (CALL)
Shift (SHIFT)
DISPLAY READOUT DESCRIPTION
No function.
Toggles display backlighting on/off.
Toggles high and low power output.
Starts and stops the scan function.
Selects a DTMF memory.
Redials the last-used DTMF code.
Toggles the lock function on/off.
Toggles confirmation beep tones on/off.
Toggles between VFO and memory modes.
Toggles tone squelch operation on/off.
Starts/stops tone scan.
Selects a tuning step for frequency selection.
Selects a squelch level.
Selects a weather channel.
Selects an ANI code.
Selects +duplex, –duplex or simplex operation.
Writes the selected frequency into a memory.
Selects the call channel.
Shifts the CPU’s clock frequency.
*
1
The DTMF memory function can only be assigned to [SQL], [SC], [DUP] or [H/L]. *
2
Weather channels are only available in the USA version.
*
3
ANI code setting only appears when ANI operation is selected through cloning (p. 36).
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 32 (1,1)
33
11
ANI OPERATION
■ ANI mode ON
ANI (Automatic Number Identification) mode can only be
turned ON using the optional CS-T2
CLONING SOFTWARE
. Con-
sult the HELP file in the CS-T2
CLONING SOFTWARE
for details.
If ANI mode is already on, resetting the CPU (see above) ef-
fectively turns ANI mode off.
■ General
The ANI (Automatic Number Identification) function is a
method of selective calling which features an answer back
function. This allows you to confirm whether or not a call has
reached the receiving party even if the operator is temporarily
away from the transceiver.
In order to use the IC-T2H’s ANI function, cloning is neces-
sary via a PC using the optional CS-T2
CLONING SOFTWARE
.
Using this software, the transceiver’s individual ANI code,
group codes, ANI time-out timer and other settings related to
ANI operation can be set. Refer to the Read Me file that
comes with the CS-T2
CLONING SOFTWARE
for available set-
tings.
Once ANI mode is programmed, the transceiver cannot use
frequency or channel display mode unless it is reprogrammed
from a PC using the CS-T2
CLONING SOFTWARE
or the CPU is
reset (see p. 30).
ANI selective code (push [PTT])
Ringing Ringing
Answer back code (automatic)
Disconnect code ([PTT] + [#])
Confirmation code (automatic)
Connection code (push [PTT])
Non-coded operation
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
P0 P1 P2 P3
12
5
8
0
4
79
6
3
A
B
C
D
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 33 (1,1)
34
11 ANI OPERATION
■ Operation
D Calling a specific station
➀ Turn power on and set the [VOL] control to the 10 or 12 o’-
clock position.
➁ Push the [Y]/[Z] keys to set the desired channel.
•“ ” appears when the ANI function has been programmed via
cloning.
➂ Push [PTT] once to connect to the selected station or enter
a 3-digit ANI code, if required (in this case it is not neces-
sary to push [PTT]—transmit is automatic after entry of the
3rd digit).
• The transceiver transmits the pre-programmed selective code.
➃ When the transceiver rings (an answer back is received),
wait for a connection code from the connected station;
when the transceiver doesn’t ring, push [PTT] again to exit
the standby condition, then try again from step ➂ after wait-
ing awhile.
➄ When the connection code is received, a beep sounds,
then “” flashes; when the connection code is not re-
ceived within 10 sec., the transceiver transmits a discon-
nect code automatically (“” does not flash). Try again
from step ➂ after waiting awhile , in such a case.
➅ When “” flashes, you can converse with the connected
station.
• Push to transmit; release to receive.
➆ When your conversation is finished, transmit the discon-
nect code.
• While pushing [PTT], push [#].
• Some transceivers cannot transmit a disconnect code depend-
ing on programming.
NOTE: When your conversation extends into the ANI time-
out time, the transceiver transmits a disconnect code au-
tomatically.
Transmit
a selective code
Push [PTT] to
exit standby
Converse
Transmit a
disconnect code
manually
Receive an
answer back
code
Receive
a connection
code
Transmit
disconnect code
automatically
No
Ye s
No
Try again after a while
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 34 (1,1)
35
11
ANI OPERATION
D Calling group stations
➀ Turn power on, then select the desired group channel.
➁ Enter the 3-digit ANI code including the group code “D”—
the transceiver calls the desired station automatically.
• The transceiver transmits the pre-programmed selective code.
• When entering a 3-digit code, the transceiver automatically trans-
mits a group code after the 3rd digit is entered.
• When making group calls the transceiver does not ring and no
answer back connection code is received.
• You can make an announcement to your group immediately with-
out a connection procedure.
➂ Push [PTT] in the regular way to communicate.
➃ When your conversation is finished, while pushing [PTT],
push [#] to transmit a disconnect code.
D Group call code examples
[Example 1]
If “11D” is transmitted, transceivers with receive codes “110”
to “119” are called.
[Example 2]
If “1D3” is transmitted, transceivers with receive codes “103,”
“113,”…“183” and “193” are called.
NOTE: “DDD” transmits to all transceivers.
D Waiting for a call
➀ Turn power on, then select the de-
sired channel.
• The transceiver may be programmed
to start a scan at power on.
➁ When you receive a selective call,
the transceiver “rings.”
• Push [ANI CODE] to display the re-
ceive code.
➂ Push [PTT] to send a connection code within 10 sec.
➃ While “” flashes, converse with the connected station.
➄ When your conversation is finished, you may receive a dis-
connect code.
• Transmitting a disconnect code from your side (push [PTT] + [#])
is also possible (except for group call receive).
• “” stops flashing.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 35 (1,1)
36
12
CLONING
Cloning allows you to quickly and easily transfer the pro-
grammed contents from one transceiver to another trans-
ceiver; or, data from a PC to a transceiver using the optional
CS-T2
CLONING SOFTWARE
.
D Transceiver-to-transceiver
cloning
➀ Connect the OPC-474
CLONING CABLE
with adapter plugs
to the [SP] jack of the master and slave transceivers.
• The master transceiver is used to send data to the slave trans-
ceiver.
➁ While pushing [H/L] + [Y], turn power on to enter cloning
mode (master transceiver only—power on only for slave
transceiver).
•“CLonE” appears and the transceivers
enter the clone standby condition.
➂ Push [PTT] on the master trans-
ceiver.
•“CLoUT” appears in the master trans-
ceiver’s display and the S/RF indica-
tor shows that data is being
transferred to the slave transceiver.
•“CL In” appears automatically in the
slave transceiver’s display and the
S/RF indicator shows that data is
being received from the master trans-
ceiver.
AT
POWER ON
➃ When cloning is finished, turn power off, then on again to
exit cloning mode.
D Cloning using a PC
Data can be cloned to and from a PC (IBM compatible) using
the optional CS-T2
CLONING SOFTWARE
and the optional OPC-
478
CLONING CABLE
. The software is necessary to access the
IC-T2H’s ANI mode. Consult the CS-T2
CLONING SOFTWARE
HELP message for details.
D Cloning error
NOTE: DO NOT push the [PTT] on the slave transceiver
during cloning. This will cause a cloning error.
When the display at right appears, a
cloning error has occurred.
In such a case, both transceivers au-
tomatically return to clone standby condition and cloning must
be repeated.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 36 (1,1)
37
13
TROUBLESHOOTING
If your transceiver seems to be malfunctioning, please check
the following points before sending it to a service center.
PROBLEM
No power comes on.
Transmitting is impossible.
Frequency cannot be set.
Scan does not function.
[Y] or [Z] keys do not
function when using the
optional HM-75A.
Squelch does not open for
received signals.
Some memory channels
cannot be selected.
ANI mode cannot be ac-
cessed.
Some functions are not
available.
POSSIBLE CAUSE
• The battery is exhausted.
(A slight current flows in the circuits even when the
power is off.)
• The battery is exhausted.
• Memory mode, call channel or channel indication
mode is selected.
• The lock function is activated.
• The same frequencies are programmed into both
scan edges.
• Only CH1 is programmed; or, all other memory
channels are set as skip channels.
• Memory channels 1 and/or 2 are not pro-
grammed and simple mode is selected.
• Tone squelch is activated.
• Some memories have been cleared or the num-
ber of active memories has been reduced.
• ANI mode can only be accessed through cloning.
• The desired function(s) has not been assigned to
a key.
SOLUTION
• Charge the battery pack or place new dry cell bat-
teries in the battery case.
(Remove the battery pack if you will not be using the trans-
ceiver for a long time.)
• Charge the batteries or place new dry cells in the
battery case.
• Push [
A V] to select VFO mode; or, turn power on
while pushing [Y] + [0] to exit channel indication.
• Set [D L] down to deactivate the lock function.
• Program different frequencies.
• Program additional memories; or, cancel skip set-
tings for one or more channels.
• Program the memory channels or set to microphone
normal.
• Turn off the tone squelch.
• Program the cleared memories or increase the num-
ber of active memory channels.
• Set ANI operation using the CS-T2
CLONING SOFT
-
WARE
.
• Set the desired function(s) using Key Customize
mode.
REF.
pgs. 9,
10
pgs. 9,
10
pgs. 11
p. 13
p. 19
p. 25
pgs.
19, 28
p. 26
pgs.
19, 30
p. 36
p. 31
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 37 (1,1)
GENERAL
• Frequency coverage : (Unit: MHz)
USA
TX 144–148
RX 136–174*
ASIA 136–174*
EUR 144–146
KOR 144–146
TAIWAN 145–146
*Guaranteed range: 144–148 MHz.
• Operating mode : F2/F3
• Frequency stability : ±10 ppm (0°C to 50°C; 32°F to 122°F)
• Antenna impedance : 50 Ω
(nominal)
• Power supply : 9.6 V DC (Ni-Cd × 8; negative ground)
• Current drain( at 9.6 V; typ.) :
Tx 1.6 A
(at 6 W; typ.)
1.5 A (Thailand version)
Rx Rated audio 210 mA (typ.)
Power saved 25 mA (typ.)
Standby 80 mA (typ.)
• Scan speed :
VFO mode 16 ch/sec.
Memory channel mode 10 ch/sec.
• Usable temperature range : –10°C to +60°C; +14°F to +140°F
• Dimensions : 58(W)×140.5(H)×32.3(D) mm;
2
9
⁄32(W)×5
17
⁄32(H)×1
9
⁄32(D) in
• Weight : 420 g; 14.8 oz
(incl. 8 Ni-Cd cells and antenna)
38
14
SPECIFICATIONS
TRANSMITTER
• Modulation system : Variable reactance modulation
• Output power (at 9.6 V DC) : High 6 W
(typ.: 144–148 MHz)
5 W
(Thailand version)
Low 1 W (typ.: 144–148 MHz)
• Max. frequency deviation : ±5 kHz
• Spurious emissions : Less than –60 dB
• Ext. microphone connector :
3-conductor 2.5(d) mm (
1
⁄
10
″); 2 kΩ
RECEIVER
• Receive system : Double conversion
superheterodyne
• Intermediate frequencies : 1st 30.85 MHz
2nd 450 kHz
• Sensitivity : 0.14 µV (typ.; for 12 dB SINAD)
• Squelch sensitivity : 0.16 µV (typ.; at threshold)
• Spurious and image rejection : 60 dB typ. (except
1
⁄2 of IF and 2nd
image frequency)
• Audio output power : 500 mW
typ.
(at 9.6 V DC) at 10% distortion with an 8 Ω load
• Ext. speaker connector : 3-conductor 3.5(d) mm (
1
⁄8″); 8 Ω
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 38 (1,1)
39
15
OPTIONS
D Battery packs
BATTERY
VOLTAGE CAPACITY
OUTPUT OPERATING
PACK POWER PERIOD*
1
BP-194
Battery case for R6(AA)×8
6.0 W 3.7 h*
2
alkaline or Ni-Cd cells
BP-195 9.6 V 700 mAh 6.0 W 3.7 h
BP-196
9.6 V 1050 mAh 6.0 W 5.5 h
*1 Operating ranges are calculated under the following conditions:
Tx : Rx : standby=1 : 1 : 8
*
2
When Ni-Cd batteries are installed.
D Chargers and cables
BC-110A/D/V WALL CHARGER
Regularly charge battery packs attached to the transceiver in 15 to
20 hrs.
BC-119 DESKTOP CHARGER + AD-81 BATTERY PACK ADAPTER
Rapidly charge battery packs in 1 to 1.5 hrs. depending on the battery
pack. An AC adapter is packed with the BC-119. The AD-81 must be
used with the BC-119 for charging the battery pack. The CP-17L or
OPC-515L can be used instead of the supplied AC adapter.
CP-12L CIGARETTE LIGHTER CABLE WITH NOISE FILTER
For charging via a 12 V cigarette lighter socket.
OPC-254L DC POWER CABLE
For charging via an external power supply.
D Speaker-microphones
D Others
CS-T2 CLONING SOFTWARE
Allows you to clone the memory contents of an IC-T2H transceiver
between transceivers or to a PC for editing.
OPC-474 CLONING CABLE
For transceiver-to-transceiver cloning.
OPC-478 CLONING CABLE
For transceiver-to-PC cloning.
LC-145 CARRYING CASE
SP-13 EARPHONE
Provides clear receive audio in noisy environments.
HM-46
HM-75A
HM-54
HS-51 HEADSET
• PTT switch
• VOX
• One-touch PTT for
hands-free operation
Remote control
capability (see p. 28 for details)
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 39 (1,1)
40
16
MODE ARRANGEMENT
CHANNEL INDICATION MODE
VFO MODE
MEMORY MODE
CALL MODE
DTMF MEMORY MODE
+
AT POWER ON
See p. 11 for details
SET MODE
MIC simple mode (p. 2
TO ENTER
Active channels (p. 30)
Start
MR
0
VIA CLONING
See p. 33 for details
See p. 22 for details
Refer to the CS-T2
cloning software
read me file for details.
ANI MODE
[ (DTMF)]
[
A V]/[ (CALL)]
for 1 sec.
T
Repeater tone (p. 16)
T SQL
CTCSS tone (p. 26)
Tone setting
DUP
Frequency offset (p. 16)
Duplex setting (p. 15)
Tuning step (p. 14)
CALL frequency (p. 20)
8
TO ENTER
#
NOTE: indicates one of the
customizable keys (see page
at right).
[A V]/[ (CALL)]
momentarily
[ (DTMF)]
[A V]
[
A V]
[ (CALL)]
[ (CALL)]
(Transmit DTMF
code.)
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 40 (1,1)
41
16
MODE ARRANGEMENT
MODE
INITIAL SET MODE
MIC simple mode (p. 28)
Auto power OFF (p. 29)
LCD backlight (p. 29)
Scan resume (p. 24)
Power saver (p. 29)
U.S.A. version only
Beep tones (p. 29)
LCD contrast (p. 29)
DTMF speed (p. 23)
+
TO ENTER at power ON
Power OFF then ON TO EXIT
Power OFF then ON TO EXIT
Auto repeater (p. 17)
Active channels (p. 30)
Start
T
er tone (p. 16)
T SQL
tone (p. 26)
tting
DUP
cy offset (p. 16)
setting (p. 15)
step (p. 14)
equency (p. 20)
8
0
+
TO ENTER at power ON
#
0
KEY CUSTOMIZE MODE
SQL
SC
DUP
H/L
A V
B M
C T
D L
KEY KEYDEFAULT SETTING DEFAULT SETTING
Squelch level
Scan start/stop
Duplex setting
Hi/low power output
VFO/memory selection
Memory write
Tone setting
Keypad lock
➀ Push a key to program—currently
assigned function is displayed.
➁ Push the [ ]/[ ] keys to select the
desired function. (See p. 32 for a list
of available functions.)
➂ Push the selected key for 1 sec. to
program the function.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 41 (1,1)
42
17
CE
ABOUT CE
CE Versions of the IC-T2H which display the “CE”
symbol on the serial number seal, comply with the es-
sential requirements of the European Radio and
Telecommunication Terminal Directive 1999/5/EC.
This warning symbol indicates that this equipment
operates in non-harmonised frequency bands and/or
may be subject to licensing conditions in the country
of use. Be sure to check that you have the correct
version of this radio or the correct programming of
this radio, to comply with national licensing require-
ment.
INSTALLATION NOTES
• When transmitting with a portable radio, hold the radio in a vertical
position with its microphone 2.5 to 5 centimeters away from your
mouth. Keep antenna at least 2.5 centimeters from your head and
body.
• If you wear a portable two-way radio on your body, ensure that the
antenna is at least 2.5 centimeters from your body when transmit-
ting.
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 42 (1,1)
43
17
CE
DECLARATION
OF CONFORMITY
We Icom Inc. Japan
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan
Kind of equipment:
144 MHz FM TRANSCEIVER
This compliance is based on conformity with the following harmonised
standards, specifications or documents:
i) EN 60950 (August 1992) with Amendment 11:1997
ii) EN 301 489-1 v1.2.1 (2000-08)
iii) EN 301 489-15 v1.1.1 (2000-09)
iv) EN 301 783-2 v1.1.1 (2000-09)
v)
Type-designation: iC-t2h
Signature
Authorized representative name
Place and date of issue
T. Aoki
General Manager
Icom (Europe) GmbH
Himmelgeister straße 100
D-40225 Düsseldorf
Düsseldorf 28 Feb. 2001
Icom (Europe) GmbH
Declare on our sole responsibility that this equipment complies the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.
Version (where applicable):
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 43 (1,1)
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan
A-5530H-1EX-w
Printed in Japan
© 1998–2003 Icom Inc.
<Intended Country of Use>
‘ GER ‘ NED ‘ ITA
‘ AUT ‘ BEL ‘ GRE
‘ GBR ‘ LUX ‘ SWE
‘ IRL ‘ ESP ‘ DEN
‘ FRA ‘ POR ‘ FIN
IC-T2H_RTTE.qxd 03.6.20 18:58 Page 44 (1,1)
… 48

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Icom IC-T2H bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Icom IC-T2H in de taal/talen: Engels als bijlage per email.

De handleiding is 1,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info