Handleiding Icom IC-R10 (pagina 83 van 84) (Engels)

12724

Verklein

Vergroot

Pagina terug

1/84

Pagina verder

INSTRUCTION MANUAL

iR10

COMMUNICATIONS RECEIVER

This device complies with Part 15 of the FCC rules. Operation is sub-

ject to the following two conditions: (1) This device may not cause

harmful interference, and (2)this device must accept any interference

received, including interference that may cause undesired operation.

IC-R10.qxd 02.1.10 11:44 Page 80 (1,1)

Versions of the IC-R10 which display the “CE” symbol on

the serial number seal, comply with the ETSI speciﬁca-

tion prETS300 684 (EMC product standard for

Commercially Available Amateur Radio Equipment).

RWARNING! NEVER connect the receiver to an AC

outlet. This may pose a fire hazard or result in an electric

shock.

RWARNING! NEVER operate the receiver with a

headset or other audio accessories at high volume levels.

Hearing experts advise against continuous high volume op-

eration. If you experience a ringing in your ears, reduce the

volume level or discontinue use.

NEVER connect the receiver to a power source of more

than 16 V DC such as a 24 V battery. This connection will ruin

the receiver.

NEVER cut the DC power cable between the DC plug and

fuse holder. If an incorrect connection is made after cutting,

the receiver might be damaged.

NEVER expose the receiver to rain, snow or any liquids.

DO NOT connect the receiver to a power source using re-

verse polarity. This connection will not only blow fuses but

also may damage the receiver.

CAUTIONSIMPORTANT

READ ALL INSTRUCTIONS CAREFULLY be-

fore attempting to operate the receiver.

SAVE THIS INSTRUCTION MANUAL — This

instruction manual contains important safety and operating in-

structions for the IC-R10.

EXPLICIT DEFINITIONS

The following explicit deﬁnitions apply to this manual.

WORD DEFINITION

RWARNING

Personal injury, ﬁre hazard or electric shock

may occur.

CAUTION

Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No risk

of personal injury, ﬁre or electric shock.

IC-R10.qxd 02.1.10 11:44 Page i (1,1)

UNPACKING

Accessories included with the receiver:

Qty.

q Antenna............................................................................1

w Handstrap.........................................................................1

e Belt clip (with 2 screws)....................................................1

r Wall charger*....................................................................1

t Ni-Cd batteries .................................................................4

* Not supplied with some versions.

DO NOT use or place the receiver in areas with tempera-

tures below –10°C (+14°F) or above +50°C (+122°F) or, in

areas subject to direct sunlight, such as the dashboard.

AVOID placing the receiver in excessively dusty environ-

ments.

AVOID the use of chemical agents such as benzine or al-

cohol when cleaning, as they damage the receiver surfaces.

Even when the receiver power is OFF, a slight current still

ﬂows in the circuits. Remove cell batteries from the receiver

when not using it for a long time. Otherwise, the installed bat-

teries will become exhausted.

For U.S.A. only

Caution: Changes or modiﬁcations to this receiver, not ex-

pressly approved by Icom Inc., could void your authority to

operate this receiver under FCC regulations.

qw e

IC-R10.qxd 02.1.10 11:44 Page ii (1,1)

TABLE OF CONTENTS

iii

IMPORTANT ..................................................................................... i

EXPLICIT DEFINITIONS .................................................................. i

CAUTIONS .......................................................................................i

UNPACKING .................................................................................... ii

TABLE OF CONTENTS ..................................................................iii

OPERATING THEORY ...................................................................iv

OPERATING NOTES ...................................................................... iv

1 PANEL DESCRIPTION ......................................................... 1 – 6

■ Front and side panels ............................................................................1

■ Top panel ...............................................................................................2

■ Function display ..................................................................................... 3

■ Keypad ..................................................................................................5

2 Ni-Cd BATTERIES AND ACCESSORIES ............................7–9

■ Charging Ni-Cd batteries .......................................................................7

■ Charging precautions ............................................................................7

■ About Ni-Cd batteries ............................................................................ 7

■ Battery installation ................................................................................. 8

■ Charging connections ............................................................................8

■ Accessory attachment ........................................................................... 9

3 BASIC OPERATION ......................................................... 10 – 22

■ General ................................................................................................10

■ Selecting VFO mode ...........................................................................10

■ Selecting a receive mode .................................................................... 12

■ Selecting a tuning step ........................................................................ 13

■ Tuning a frequency (via the keypad) ...................................................14

■ Tuning a frequency (via the [DIAL]) .....................................................15

■ Dial select steps ..................................................................................16

■ Band scope function ............................................................................17

■ Listening example 1 ............................................................................. 19

■ Listening example 2 ............................................................................. 21

4 MEMORY MODE .............................................................. 23 – 34

■ General ................................................................................................23

■ Selecting memory mode ......................................................................23

■ Setting a bank and memory channel ...................................................24

■ Programming a memory channel—1 ...................................................25

■ Programming a memory channel—2 ...................................................26

■ Programming a memory channel—3 ...................................................27

■ Programming example 1 .....................................................................29

■ Programming example 2 .....................................................................30

■ Programming example 3 .....................................................................31

■ Memory copy .......................................................................................33

■ Copying example 1 ..............................................................................34

■ Copying example 2 ..............................................................................34

5 SCANNING OPERATION ................................................. 35– 46

■ General ...............................................................................................35

■ Before scanning ................................................................................... 37

■ Full scan .............................................................................................. 39

■ Memory scan .......................................................................................39

■ Program scan ...................................................................................... 40

■ Auto memory write scan ......................................................................41

■ BANK scan .......................................................................................... 43

■ Mode select scan ................................................................................. 44

■ Skip function ........................................................................................45

■ SIGNAVI function .................................................................................46

6 PRIORITY WATCH ........................................................... 47 – 49

■ General ...............................................................................................47

7 EASY MODE ............................................................................ 50

■ General ................................................................................................50

■ EASY mode operation ........................................................................50

8 EDIT FUNCTION .............................................................. 51 – 58

IC-R10.qxd 02.1.10 11:44 Page iii (1,1)

TABLE OF CONTENTS

OPERATING THEORY

Electromagnetic radiation which has frequencies of 20,000

Hz (20 kHz*) and above is called radio frequency (RF) energy

because it is useful in radio transmissions. The IC-R10 re-

ceives RF energy from 0.5 MHz to 1300 MHz* and converts it

into audio frequency (AF) energy which in turn actuates a

loudspeaker to create sound waves. AF energy is in the

range of 20 to 20,000 Hz.

*kHz is an abbreviation of kilohertz or 1000 hertz, MHz is abbreviation

of megahertz or 1,000,000 hertz, where hertz is a unit of frequency.

■ General ................................................................................................51

■ Memory channel edit ........................................................................... 51

■ Program scan channel edit ..................................................................55

■ EASY mode channel edit ..................................................................... 55

■ Program scan or EASY mode channel edit .........................................57

9 SET MODE ....................................................................... 59 – 62

■ General ...............................................................................................62

10 OTHER FUNCTIONS ........................................................63–71

■ Low battery indicator ...........................................................................63

■ AFC function ........................................................................................63

■ Monitor function ...................................................................................64

■ Lock function .......................................................................................64

■ ATT function ........................................................................................ 65

■ NB/ANL function ..................................................................................65

■ Sleep timer ..........................................................................................66

■ User TS setting ....................................................................................66

■ Memory search function ...................................................................... 67

■ Auto mode and TS function .................................................................69

■ Resetting the CPU ...............................................................................70

■ Data cloning ........................................................................................ 71

11 ALPHANUMERIC KEY ASSIGNMENT ...................................72

12 CONTROL COMMANDS .................................................. 73 – 74

■ General ................................................................................................73

■ Data format ..........................................................................................73

■ Command table ................................................................................... 73

13 TROUBLESHOOTING ......................................................75–76

14 SPECIFICATIONS ...................................................................77

15 OPTIONS .................................................................................78

OPERATING NOTES

The IC-R10 may receives its own oscillated frequency, result-

ing in no reception or only noise reception, on some frequen-

cies.

The IC-R10 may receive interference from extremely strong

signals on different frequencies or when using an external

high-gain antenna.

IC-R10.qxd 02.1.10 11:44 Page iv (1,1)

PANEL DESCRIPTION

■ Front and side panels

FUNCTION SWITCH (pgs. 5, 6)

While pushing [FUNC], the sec-

ondary functions of switches and

controls can be accessed.

FUNCTION DISPLAY (p. 3)

Indicates the operating condition.

KEYPAD (pgs. 5, 6)

Numeral and other function keys

for tuning and activating func-

tions.

SPEAKER

Emits the receive audio.

CI-V JACK (p. 73)

Connect the optional OPC-478

CLONING CABLE for remote

control or data cloning.

EXTERNAL DC POWER JACK

(p. 8)

Connect the supplied wall charg-

er for charging the installed Ni-Cd

battery cells.

Be careful of overcharging!

Operation with an external DC

power source simultaneously

charges the installed batteries.

When [CHARGE] switch is ON,

see p. 8.

IC-R10.qxd 02.1.10 11:44 Page 1 (1,1)

PANEL DESCRIPTION

■ Top panel

ANTENNA CONNECTOR (p. 9)

Connects the supplied flexible

antenna. Be careful when con-

necting an external antenna

(See Operating Notes, p. iv).

VOLUME CONTROL [VOL]

(p. 10)

Adjusts the audio output level.

SQUELCH CONTROL [SQL]

(p. 11)

➥Varies the squelch threshold

point for audio mute.

• Pushing [MONI] opens the

squelch momentarily.

➥Varies the RF gain in LSB,

USB and CW modes.

EXTERNAL SPEAKER JACK

[SP]

Connect an 8 ohm optional

speaker or an earphone, if de-

sired.

The internal speaker will not

function when either option is

connected.

Connect the optional OPC-

478/479

CLONING CABLE for

cloning from a PC or another IC-

R10 (p. 71).

TUNING CONTROL [DIAL]

Used to set an operating fre-

quency (p. 15), memory channel

(p. 24), etc.

IC-R10.qxd 02.1.10 11:44 Page 2 (1,1)

PANEL DESCRIPTION

AT TVSCEASYVFOMEMO

AFCCWUSBLSBAMWFM

qw e r uty i o!0

■ Function display

IC-R10.qxd 02.1.10 11:44 Page 3 (1,1)

PANEL DESCRIPTION

q SLEEP TIMER INDICATOR

Appears while the sleep timer is activated (p. 66).

w FUNCTION INDICATOR

Appears while the function ([FUNC]) switch is pushed.

e MEMORY MODE INDICATOR

Appears while in memory mode (p. 23).

r VFO MODE INDICATOR

Appears while in VFO mode (p. 11).

t RECEIVE MODE INDICATOR

Indicates the selected receive mode (p. 12).

y EASY MODE INDICATOR

Appears while in easy mode (p. 50).

u VSC INDICATOR

Appears while the VSC function is turned ON (p. 38).

i ATTENUATOR INDICATOR

Appears while the attenuator is turned ON (p. 65).

o AFC INDICATOR

Appears while the AFC function is turned ON (p. 63).

!0 LOCK INDICATOR

Appears while the lock function is activated (p. 64).

!1 MULTI-FUNCTION DOT MATRIX

Indicates the following items:

Opening message (p. 10)

Receive frequency (p. 11)

Tuning steps (p. 13)

Band scope (p. 17)

Memory bank and channel number (p. 23)

Memory name (p. 31)

Memory bank name (p. 32)

Programmable scan edges and name (p. 40)

Priority frequency (p. 49)

SET mode contents (p. 59)

Signal strength indicator

IC-R10.qxd 02.1.10 11:44 Page 4 (1,1)

PANEL DESCRIPTION

■ Keypad

KEY PRIMARY FUNCTION SECONDARY FUNCTION (while pushing [FUNC])

Push for 1 sec. to toggle power ON and OFF. Opening mes-

sage appears for 1 sec. after power ON

(p. 10).

Not available

Push and hold this switch to force the squelch open (p. 64).

Not available

Selects a receive mode: FM, AM, USB, LSB, CW or WFM

(p. 12).

Selects tuning step set mode (p. 13).

Clears numeric key input (p. 14).

Stops scanning (p. 39).

Selects SET mode (p. 59).

Toggles VFO or MEMORY mode

(pgs. 11, 23).

In VFO mode: writes to a memory channel

(p. 29).

In MEM-

ORY mode: transfers memory contents to VFO mode

(p. 33)

or copies to another channel

(p. 33).

Starts/stops scanning (p. 39). In VFO mode: selects a dial select step (p. 16).

Selects EASY mode (p. 50). Selects memory channel name search mode (p. 67).

Selects memory edit mode. (except when in VFO mode; p.

51).

Locks all switches and controls electronically except [VOL],

[SQL], [FUNC], [POWER] and [MONI]

(p. 64).

In VFO mode: enters the selected receive frequency (p. 14).

In MEMORY mode: enters the selected memory channel by

the memory search function (p. 68).

Activates the noise blanker while in SSB and CW mode, or

the ANL function while in AM mode

(p. 65).

POWER

MONI

MODE

CLR

SET

V/M

SCAN

DIAL SEL

EASY

EDIT

LOCK

ENT

NB/ANL

IC-R10.qxd 02.1.10 11:44 Page 5 (1,1)

PANEL DESCRIPTION

KEY PRIMARY FUNCTION SECONDARY FUNCTION (while pushing [FUNC])

When FM receive mode is selected in VFO mode: toggles the band scope function (p. 17).

Toggles the VSC function ON and OFF (p. 38).

Selects the sleep timer conditions (p. 66).

In VFO mode: sets program scan edge frequencies for programmed scan (p. 40).

In VFO mode: sets program scan edge frequencies for auto memory write scan (p. 41).

In VFO mode: toggles the signal navigator function ON/OFF for full, programmed or auto

memory write scan

(p. 46).

In MEMORY mode: sets the receive mode for mode select scan

(p. 44).

In MEMORY mode: sets the BANK for bank scan

(p. 43).

Starts/stop priority watch (p. 49).

Toggles the attenuator ON/OFF (p. 65).

ENT

NB/ANL

SLEEP

VSC

BSCOPE

PROG-S

AMWS

SIGNAVI

PRIO

BANK-S

MODE-S

AFC

ATT

BSCOPE

VSC

SLEEP

PROG-S

AMWS

SIGNAVI

MODE-S

BANK-S

PRIO

ATT

IC-R10.qxd 02.1.10 11:44 Page 6 (1,1)

Ni-Cd BATTERIES AND ACCESSORIES

■ Charging Ni-Cd batteries

The supplied Ni-Cd batteries are rechargeable and can be

charged approx. 300 times. Charge the batteries before ﬁrst

operating the receiver or when the batteries become ex-

hausted.

If you want to be able to charge the batteries more than 300

times, the following points should be observed:

1. Avoid overcharging. The charging period should be less

than 48 hours.

2. Use the batteries until they become almost completely ex-

hausted under normal conditions. We recommend battery

charging just after receiving becomes impossible.

■ Charging precautions

NEVER attempt to charge dry cell batteries. This will cause

internal liquid leakage and damage the receiver.

NEVER connect two or more chargers at the same time.

Charging may not occur under temperatures of 10°C (50°F)

or over temperatures of 40°C (104°F).

■ About Ni-Cd batteries

Ni-Cd battery life

If your Ni-Cd batteries seems to have no capacity even after

being fully charged, completely discharge them by leaving the

power ON overnight. Then, fully charge the Ni-Cd batteries

again. If the Ni-Cd batteries still do not retain a charge (or

very little), new batteries must be purchased.

Recycling information (U.S.A. only)

The product that you purchased contains

rechargeable batteries. The batteries are recy-

clable. At the end of their useful life, under vari-

ous state and local laws, it may be illegal to

dispose of these batteries into the municipal waste stream.

Call 1-800-8-BATTERY for battery recycling options in your

area or contact your dealer.

RBRC

Ni-

IC-R10.qxd 02.1.10 11:44 Page 7 (1,1)

Ni-Cd BATTERIES AND ACCESSORIES

■ Battery installation

Install 4 AA (R6) size batteries as illustrated below.

Remove the cover from the receiver.

Install 4 AA (R6) size dry cell, alkaline or the supplied Ni-Cd

batteries into the receiver.

CAUTION: Make sure the polarity of the batteries is cor-

rect before installing. Reverse polarity may damage the re-

ceiver.

NOTE: DO NOT use different types of batteries at the

same time otherwise the receiver may not work properly.

■ Charging connections

Conﬁrm that the [CHARGE] switch is ON, then connect the

supplied wall charger via an AC outlet as shown below.

to [DC]

BC-110A/E/D/V*

*Not supplied with

some versions.

CP-12L (optional)

To cigarette lighter

socket

OPC-254L (optional)

To power supply

(4.8–13.5 V DC)

Black

White

CHARGE

OFF ON

CAUTION: Make sure the

[CHARGE] switch is in the OFF po-

sition when operating the receiver

with one of the above power sup-

plies.

IC-R10.qxd 02.1.25 13:10 Page 8 (1,1)

Ni-Cd BATTERIES AND ACCESSORIES

■ Accessory attachment

Antenna

Insert the supplied antenna into the

antenna connector and rotate the an-

tenna as shown in the diagram

below. Keep the jack cover attached

when jacks are not in use to avoid

bad contacts.

Belt clip

Attach the belt clip using the supplied

screws.

Conveniently attaches to your belt.

Handstrap

Attach the handstrap as shown in the

diagram below. Facilities carrying.

IC-R10.qxd 02.1.10 11:44 Page 9 (1,1)

1. Turn power ON

Push [POWER] for 1 sec. to turn

power ON.

•Opening message is displayed for 1

sec.

BASIC OPERATION

■ General

Operating the IC-R10 is easy. However,

in order to get the most out of its oper-

ating potential, please go through the

following procedures, step-by-step.

Then, try the examples contained at the

end of this chapter.

What is VFO?

The IC-R10 has several operating

modes, each of which has its own dis-

tinct functions. VFO (Variable

Frequency Operation) is one of these

modes.

VFO mode is used to change the oper-

ating frequency, receive mode, tuning

step, etc. Therefore, for most every day

operations of the receiver, you will be

using VFO mode.

■ Selecting VFO mode

2. Adjust the volume

Adjust the audio to a suitable level

using [VOL].

Check the squelch position (see next

page) or VSC function setting (p. 38)

if no audio is emitted.

VFO

Presented

by ICOM

Opening message as

above is displayed on the

multi-function display.

IC-R10.qxd 02.1.10 11:44 Page 10 (1,1)

3-1. Adjust the RF gain

Rotate [SQL] maximum counter-

clockwise, to adjust RF gain to opti-

mum level.

What is RF gain?

RF gain controls receive sensitivity

gain—reduce the gain when you

don’t want to receive very weak sig-

nals or when excessively strong in-

terfering signals are being received,

etc.

4. Select VFO mode

When MEMORY mode is selected,

push [V/M] to select VFO mode.

When SET or TS set mode is se-

lected, push [CLR] to select VFO

mode.

• The VFO indicator appears.

BASIC OPERATION

3. Adjust the squelch

Rotate [SQL] maximum counter-

clockwise, then rotate it clockwise

until audio is just muted when receiv-

ing no signal for FM, WFM or AM

mode. (see right page)

What is squelch?

A squelch circuit allows you to mute

undesired noise while receiving no

signal and emit audio while receiving

signals. This provides quiet standby.

The [MONI] switch changes the

squelch setting. This is useful for

weak signal reception (p. 64).

VFO

144.0000

VFO indicator

IC-R10.qxd 02.1.10 11:44 Page 11 (1,1)

BASIC OPERATION

■ Selecting a receive mode

What are receive modes?

Radio signals can be propagated in a variety of ways (or

modes). Each mode has its own physical properties that de-

termine to some degree its uses.

The IC-R10 receives the 6 most common modes: AM, FM,

WFM, USB, LSB and CW. When you want to tune a station,

you MUST set the receive mode ﬁrst. The table below shows

common uses for each mode.

Major symptoms of incorrect receive mode

Distorted sound

Sudden interruption in reception

Noise only

Noise with weak reception

Low or unstable signal strength indicator value

MODE COMMON USAGE

AM amateur, aviation, broadcasting

FM amateur, utility

WFM TV broadcasting, FM broadcasting

USB, LSB commercial, amateur, short wave radio

CW commercial, amateur

VFO

144.0000

VFO

144.0000

AUTO MODE

VFO

WFM

144.0000

VFO

144.0000

VFO

LSB

144.0000

VFO

USB

144.0000

VFO

144.0000

When programmed

(see p. 69)

IC-R10.qxd 02.1.10 11:44 Page 12 (1,1)

BASIC OPERATION

What are tuning steps?

Tuning steps are the frequency change

increments when you rotate the tuning

control or operate a scan. The following

steps are available: 0.1, 0.5, 1, 5, 6.25,

8, 9, 10, 12.5, 15, 20, 25, 30, 50, 100

kHz and user programmable tuning

steps (p. 66).

It is important to set the proper tuning

step for the type of station you want to

listen to. Some tuning steps are deter-

mined by frequency band or receive

mode and others are set by tradition.

Generally speaking, if you set a tuning

step smaller than that needed you will

still be able to tune a station you want

(or scan it), however, tuning (or scan-

ning) will not be efﬁcient. On the other

hand, if you select a tuning step which

is too large, you may not be able to ﬁnd

the station you are looking for.

Consult local listings.

1. Call up the tuning step

set mode

Once you have selected VFO mode

and the desired receive mode, while

pushing [FUNC], push [

(MODE)TS].

2. Select the tuning step

q Rotate [DIAL] to select the desired

tuning step.

w Push [CLR] to return to VFO

mode after the selection.

■ Selecting a tuning step

IC-R10.qxd 02.1.10 11:44 Page 13 (1,1)

BASIC OPERATION

When you know the exact frequency

you want to listen to, the quickest way

to tune it is by direct keypad entry.

Remember that the frequency must be

between 0.5 MHz and 1300 MHz.

The diagram below shows the correla-

tion between the function display fre-

quency digits and the frequency.

1. Select the frequency

Select VFO mode and the receive

mode in advance then:

Push the numeral keys in the same

order as the frequency you want to

tune (including the decimal key).

•If you make a mistake, push [CLR] and

start again.

2. Enter the frequency

When the frequency you want is dis-

played:

Push [ENT] (or numeral keys for the

0.1 kHz digit) to enter it.

•When you select a frequency outside of

the allowed range, the display will revert

back to the previously displayed fre-

quency.

ENT

NB/ANL

SLEEP

VSC

BSCOPE

PROG-S

AMWS

SIGNAVI

PRIO

BANK-S

MODE-S

AFC

ATT

■ Tuning a frequency (via the keypad)

VFO

10 MHz 10 kHz

100 MHz

100 kHz

1 kHz

100 Hz

1 MHz

1 GHz

300 .0000

IC-R10.qxd 02.1.10 11:44 Page 14 (1,1)

BASIC OPERATION

■ Tuning a frequency (via the dial)

When you want to listen to frequencies

near the displayed frequency, the easi-

est way to tune them is with the tuning

dial.

All signals have what is called an “oc-

cupied bandwidth.” They will be re-

ceived as long as the receiver is tuned

anywhere within this bandwidth. Even

though the frequency received may not

be the central frequency, the tuning

step should be made as small as pos-

sible (0.5 or 5 kHz) and the receiver

tuned to the point of greatest signal

strength indicator deﬂection.

To change frequencies faster than the

tuning step, use the dial select function

(p. 16).

1. Select VFO mode and

a receive mode

q Push [CLR] or [V/M] to select VFO

mode.

w Push [MODE] to select a receive

mode.

e Set tuning step if desired (p. 14).

2. Tune a frequency

Rotate [DIAL] to change the fre-

quency.

•The frequency changes in increments

determined by the tuning step.

•To change the frequency faster, use the

dial select function (p. 16).

IC-R10.qxd 02.1.10 11:44 Page 15 (1,1)

BASIC OPERATION

■ Dial select steps

What are dial select steps?

When tuning with the dial, if you want to change the fre-

quency faster than the selected tuning step can, use the dial

select function.

A dial select step is an increment of frequency change much

like a tuning step is. Unlike a tuning step however, a dial se-

lect step has no relation to the type of station you want to tune

or to the scan operations.

Dial select steps are available for:

VFO

144.0000

VFO

144.0000

VFO

144.0000

VFO

144.0000

FUNC

SCAN

DIAL SEL

SCAN

DIAL SEL

SCAN

DIAL SEL

SCAN

DIAL SEL

SCAN

DIAL SEL

Changing the frequency with the dial select step

In VFO mode:

Push and hold [FUNC], then rotate [DIAL].

To change the dial select step:

While pushing [FUNC], push [

(SCAN)DIAL SEL] one or sev-

eral times until the frequency digit you want to change

ﬂashes.

VFO

144.0000

100 kHz

1 MHz

10 MHz

100 MHz

IC-R10.qxd 02.1.10 11:44 Page 16 (1,1)

BASIC OPERATION

■ Band scope function

What is the band scope function?

The band scope detects signal availability in the range of ±5

channels (up to ±100 kHz) from the displayed frequency, and

displays the result on the multi function dot-matrix display.

This gives you a visual reference of current band conditions.

In this case, channel refers to sweep step or channel space

according to the set tuning step. For example, when the tun-

ing step is set to 5 kHz, the band scope detects 25 kHz above

and below the displayed frequency, then displays the result

on the LCD.

When the tuning step is set above 20 kHz, the band scope

function automatically changes its sweep step to 20 kHz.

However, when the sweep step is changed to 20 kHz, the

tuning step remains the same.

Also, when a user-programmable tuning step is selected, the

band scope function automatically selects the 20 kHz sweep

step.

Preparation

The band scope function is activated only when FM receive

mode is selected in VFO mode.

q Push [V/M] to select VFO mode. (p. 11)

w Push [MODE] one or more times to select FM mode.

(p. 12)

e While pushing [FUNC], push [

(MODE)

TS]

r Rotate [DIAL] to select the tuning/sweep step.

t Push [CLR] to return to VFO mode.

IC-R10.qxd 02.1.10 11:44 Page 17 (1,1)

BASIC OPERATION

Set band scope function

q While pushing [FUNC], push [(1)BSCOPE].

Repeat the above step or push [CLR] to turn OFF the band

scope function.

VFO

144.0000

higher freq.

displayed freq.

lower freq.

signal

strength

IC-R10.qxd 02.1.10 11:44 Page 18 (1,1)

BASIC OPERATION

■ Listening example 1 — television broadcast in WFM mode

1. Turn power ON

Push [POWER] for 1 sec. to turn

power ON.

2. Select VFO

Push [CLR] or [V/M] to select VFO

mode.

3. Adjust volume

Rotate [VOL] to obtain the desired

level of audio output.

4. Adjust squelch

Rotate [SQL] fully counterclockwise,

then clockwise until the audio noise

just disappears.

5. Select the receive

mode

Television sound is broadcast in

WFM mode. If the receiver is not al-

ready in WFM mode:

Push [MODE] one or more times until

WFM appears in the function display.

6. Select the tuning step

In most countries* television stations

are spaced about 50 kHz apart. To

select the 50 kHz tuning step:

While pushing [FUNC], push

[

(MODE)TS], then rotate [DIAL] until

the function display shows “50 kHz”.

Push [CLR] after setting to return to

VFO mode.

*Check listings for your area.

VFO

WFM

TS 50.00kHz

SET TS

TS 50.00kHz

[DIAL]

VFO

WFM

144.0000

Appears

MODE

IC-R10.qxd 02.1.10 11:44 Page 19 (1,1)

8. Use the tuning dial

Rotate [DIAL] to search for nearby

stations above and below the tuned

frequency.

BASIC OPERATION

7. Tune the station

Use the keypad to enter the fre-

quency — (example 59.75 MHz).

[Example]

(Example 59.75 MHz)

7-1. Tune the station

Enter the frequency from the 100 kHz

digit when you want to change below

the 1 MHz digit only — (example

from 59.75 MHz to 59.25 MHz).

[Example]

59.7500

VFO

WFM

ENT

59. 75

VFO

WFM

59.

VFO

WFM

. 59

VFO

WFM

59.2500

VFO

WFM

ENT

59. 25

VFO

WFM

59.

VFO

WFM

(Example 59.25 MHz)

59.3000

VFO

WFM

59.2500

VFO

WFM

59.2000

VFO

WFM

[DIAL]

NOTE: WFM and regular FM share the

same circuit. Depending on the receive

condition, this may result in distortion.

In such cases, try lowering the fre-

quency 30–50 kHz.

IC-R10.qxd 02.1.10 11:44 Page 20 (1,1)

BASIC OPERATION

1. Turn power ON

Push [POWER] for 1 sec. to turn

power ON.

2. Select VFO

Push [CLR] or [V/M] to select VFO

mode.

3. Adjust volume

Rotate [VOL] to obtain the desired

level of audio output.

4. Adjust squelch

Rotate [SQL] fully counterclockwise,

then clockwise until the audio noise

just disappears.

5. Select the receive

mode

Airband communications are in AM

mode. If the receiver is not already in

AM mode:

Push the [MODE] switch one or more

times until AM appears in the function

display.

■ Listening example 2 — airband broadcast in AM mode

6. Select the tuning step

Tuning steps for the airband are usu-

ally 25 kHz*. To set the 25 kHz tun-

ing step:

While pushing [FUNC], push

[

(MODE)TS], then rotate [DIAL] until

“25 kHz” appears in the function dis-

play.

*Check listings for your area.

VFO

144.0000

MODE

Appears

VFO

SET TS

TS 25 .00kHz

[DIAL]

IC-R10.qxd 02.1.10 11:44 Page 21 (1,1)

BASIC OPERATION

(Example 118.00 MHz)

7. Tune the station

Enter a frequency of 118.0000 MHz*

using the keypad (p. 14).

*Check listings for your area.

7-1. Tune the station

Enter the frequency from the 100 kHz

digit when you want to change below

the 1 MHz digit only — (example

from 118 MHz to 118.925 MHz).

8. Use the tuning dial

Rotate [DIAL] to search for nearby

stations above and below the tuned

frequency.

VFO

118

VFO

118 .0000

ENT

(Example 118.925 MHz)

VFO

118 .

ENT

VFO

118. 925

VFO

118 .9250

VFO

118.9000

VFO

118 .9250

VFO

118 .9500

[DIAL]

IC-R10.qxd 02.1.10 11:44 Page 22 (1,1)

MEMORY MODE

■ General

What is memory mode?

MEMORY mode is the second operating mode—the first

being VFO mode. MEMORY mode is used to store often-

used frequencies, their receive modes, attenuator settings

(p. 65), as well as skip information for scanning (p. 56). This

provides convenient recall and scanning capabilities. Also,

frequencies are receivable in MEMORY mode which means

you can listen to received signals while you are in MEMORY

mode.

The IC-R10 has 1000 memory channels for your conve-

nience. They are divided into 18 banks: BANKS A to P con-

tain 50 channels each for normal usage, while BANKS Q and

R contain 100 channels each for auto-memory write scan

(p. 41) and program skip scan (p. 45), respectively.

Each BANK and memory channel has BANK or memory

name capabilities, for convenience. BANK names can be up

to 10 characters; channel names up to 8 characters.

Programmed contents and names can be easily copied to

other channels using the memory copy function (p. 33) and

easily edited using the EDIT function (p. 51).

■ Selecting MEMORY mode

Select MEMORY mode

Push [V/M] to select MEMORY mode.

•“MEMO” appears in the function display.

• Push [V/M] again to return to VFO mode.

MEMO

A00 144 .0000

Appears

IC-R10.qxd 02.1.10 11:44 Page 23 (1,1)

MEMORY MODE

■ Selecting a BANK and memory channel

Selecting a BANK

channel

When your desired memory channel

is not stored or you do not want to

store a frequency in the displayed

BANK, you must change the BANK

number.

While pushing [FUNC], rotate [DIAL].

Selecting a memory

channel—1

If you want to recall a memory chan-

nel which has been memorized, this

is the easiest way.

Rotate [DIAL].

Selecting a memory

channel—2

If you remember the memory channel

number you want to recall, this is the

fastest way to recall it.

Enter the full 2-digit memory channel

number via the keypad.

Also, when you want to recall a blank

channel for programming, you have

to enter a channel number via the

keypad.

IC-R10.qxd 02.1.10 11:44 Page 24 (1,1)

1. BANK and memory

channel setting

q Select MEMORY mode (p. 23).

w Set the BANK and memory chan-

nel number (p. 24) you want to

program to.

2. Setting other

information

q Select VFO mode (p. 11).

w Set the frequency and receive

mode (p. 12) you want in VFO

mode.

MEMORY MODE

■ Programming a memory channel — 1

This is the quickest way to memorize a

received frequency, along with its re-

ceive mode and other information.

When you memorize the frequency in

this way, the previously memorized data

is replaced with the new data. If you do

not want to lose the previously memo-

rized data, select a blank channel num-

ber before programming (p. 24).

3. Programming

While pushing [FUNC], push

[

(V/M)MW] to program the data.

•When programming is successfully

completed, 3 beeps sound.

IC-R10.qxd 02.1.10 11:44 Page 25 (1,1)

1. Setting receive

conditions

q Select VFO mode (p. 11).

w Set the frequency and receive

mode (p. 12).

2. BANK and memory

channel setting

While pushing

[FUNC], push

[

(V/M)MW].

MEMORY MODE

■ Programming a memory channel — 2

This is the simplest method to memo-

rize the received frequency along with

its receive mode and other information.

4. Programming

While pushing [FUNC], push

[

(V/M)MW] for 2 sec. to program the

data.

•When programming is successfully

completed, 3 beeps sound and VFO

mode is automatically selected.

3. BANK and memory

channel setting

q While pushing [FUNC], rotate

[DIAL] to select the BANK you

want to program into.

w Rotate [DIAL] to select the mem-

ory channel you want to program.

IC-R10.qxd 02.1.10 11:44 Page 26 (1,1)

1. Set up

q Set the frequency you want to program in VFO mode.

w While pushing [FUNC], push [

(V/M)

MW] to enter mem-

ory write mode.

2. BANK and memory channel setting

q While pushing [FUNC], rotate [DIAL] to select the BANK

you want to program (p. 24).

w Rotate [DIAL] or push 2 digit keys to select the memory

channel you want to program (p. 24).

MEMORY MODE

■ Programming a memory channel — 3

This is the easiest way to memorize the received frequency,

mode and other information along with memory, BANK

names, scanning condition, etc. in one operation.

3. Programming details

q Push [EDIT] to enter memory programming mode.

w Rotate [DIAL] or enter the alphanumeric characters via

the keypad to program a memory name.

• When you enter channel names with [DIAL] or a character as-

signed to the same key, push [ENT] before you enter the next

character to change the digit (see page 72 for alphanumeric

key assignments).

IC-R10.qxd 02.1.10 11:44 Page 27 (1,1)

MEMORY MODE

3. Programming details — cont.

e Push [EDIT], then rotate [DIAL] to select receive mode.

r Push [EDIT], then rotate [DIAL] to select the skip scan

condition.

t Push [EDIT], then rotate [DIAL] to select the attenuator

condition.

y Push [EDIT], then rotate [DIAL]

or enter alphanumeric charac-

ters to program a BANK name.

• When you enter channel names

with [DIAL] or a character as-

signed to the same key, push

[ENT] before you enter the next

character to change the digit (see

page 72 for alphanumeric key as-

signments).

3. Programming details — cont.

u Push [EDIT], to display your programmed frequency for

conﬁrmation. When the correct frequency is displayed,

push [EDIT] for 2 sec. to return to VFO mode.

When you want to return to VFO mode immediately, push

[EDIT] for 2 sec. at any time.

IC-R10.qxd 02.1.10 11:44 Page 28 (1,1)

MEMORY MODE

■ Programming example 1 — (118.0250 MHz; AM to channel B07)

1. BANK and memory

channel setting

q Push [V/M] to select MEMORY

mode.

w While pushing [FUNC], rotate

[DIAL] to select BANK “B”.

e Push [0] and [7] to enter the mem-

ory channel number.

2. Data setting

q Push [V/M] to select VFO mode.

w Push [MODE] one or more times

to select AM mode.

e Push numeral keys or rotate

[DIAL] to set the frequency

118.0250 MHz.

3. Programming the data

While pushing [FUNC], push

[

(V/M)MW] for 2 sec.

MEMO

FUNC

[DIAL]

VFO

144.0000

MODE

MEMO

B07 .

BLANK

"BLANK" appears when

the memory channel is not

programmed.

VFO

118 .

VFO

118 .0250

ENT

IC-R10.qxd 02.1.10 11:44 Page 29 (1,1)

MEMORY MODE

■ Programming example 2 — (59.75 MHz; WFM to channel A45)

1. Setting the frequency

q Push [V/M] to select VFO mode.

w Push [MODE] one or more times

to select WFM mode.

e Push numeral keys or rotate

[DIAL] to set the frequency to

59.75 MHz.

2. Set the BANK and

memory channel

q While pushing [FUNC], push

[

(V/M)MW] to enter memory write

mode.

w While pushing [FUNC], rotate

[DIAL] to select BANK “A”.

e Rotate [DIAL] select channel “45”

or push [4] and [5] to enter the

memory channel number.

3. Programming the data

While pushing [FUNC], push

[

(V/M)MW] for 2 sec.

VFO

WFM

144.0000

MODE

VFO

WFM

SET BANK

FUNC

[DIAL]

VFO

WFM

59.7500

ENT

VFO

WFM

SET CH NO.

A45 BLANK

[DIAL]

"BLANK" appears when

the memory channel is not

programmed.

IC-R10.qxd 02.1.10 11:44 Page 30 (1,1)

MEMORY MODE

■ Programming example 3 — (121.5 MHz, EMER.,AM, SKIP: OFF, ATT: OFF, Aviation to channel F01)

1. Setting the frequency

q Push [V/M] to select VFO mode.

w Rotate [DIAL] or push numeral

keys to enter 121.5 MHz.

2. BANK and memory

channel setting

q While pushing [FUNC], push

[

(V/M)MW].

w While pushing [FUNC], rotate

[DIAL] to select BANK “F”.

e Rotate [DIAL] or push [0] then [1]

to select channel “01”.

3. Programming details

q Push [EDIT] to enter memory set-

ting mode.

w Rotate [DIAL] until the character

“E” appears then push [ENT] or

push [3] twice to enter the “E.”

e Rotate the [DIAL] then push [ENT]

to enter the characters ”M”, “E”,

“R” and “.” for memory names or

push numeral keys (see page 72

for alphanumeric key assign-

ments).

SET CH NAME

F01 E

[DIAL]

ENT

VFO

SET BANK

FUNC

[DIAL]

VFO

121 .5000

ENT

SET CH NAME

F01

EDIT

VFO

SET CH NO .

F01 BLANK

[DIAL]

IC-R10.qxd 02.1.10 11:44 Page 31 (1,1)

MEMORY MODE

3. Programming details

— cont.

t Push [EDIT] to change the re-

ceive mode item.

y Rotate [DIAL] to select AM mode,

then push [EDIT] to change the

item.

u Rotate [DIAL] to select the OFF

position for SKIP setting, then

push [EDIT].

3. Programming details

— cont.

i Rotate [DIAL] to select the OFF

position for attenuator setting,

then push [EDIT].

o Rotate [DIAL] until the character

“A” appears, then push [ENT] or

push [2] once to enter “A”.

!0 Rotate [DIAL ]then push [ENT] to

enter the characters for BANK

names or push numeral keys (see

page 72 for alphanumeric key as-

signments).

3. Programming details

— cont.

!1 The display shows the pro-

grammed frequency for conﬁrma-

tion; push and hold [EDIT] for 2

sec. if the frequency is correct.

• After pushing and holding [EDIT],

VFO mode is automatically selected.

VFO

SET MODE

MODE:AM

[DIAL]

VFO

SET SKIP

SKIP: OFF

[DIAL]

VFO

SET ATT

ATT: OFF

[DIAL]

VFO

SET B-NAME

F:A

ENT

[DIAL]

VFO

121 .5000

EDIT

Push

for

2 sec.

IC-R10.qxd 02.1.10 11:44 Page 32 (1,1)

MEMORY MODE

■ Memory copy

What is the memory copy function?

The memory copy function copies the contents (minus BANK

names) of the selected memory channel to VFO or to another

memory channel. This is quite useful when you want to

search for signals around the displayed frequency or when

you want to edit memory channels.

Copy to VFO mode

q Push [V/M] to select memory mode.

w Select the BANK and memory channel you want to copy

(p. 24).

e While pushing [FUNC], push

[

(V/M)MW] for 2sec.

Copy to the other memory channel

q Push [V/M] to select memory mode. (p. 23)

w Select the BANK and memory channel you want to copy

(p. 24).

e While pushing [FUNC], push [

(V/M)MW].

r Set the BANK and channel number you want to copy to

(p. 24).

t While pushing [FUNC], push [

(V/M)MW] for 2 sec.

IC-R10.qxd 02.1.10 11:44 Page 33 (1,1)

MEMORY MODE

■ Copying example 1

(59.7500 MHz, WFM, A45 to VFO)

q Push [V/M] to select memory mode (p. 23).

w Select the memory channel A45 (p. 24).

e While pushing [FUNC], push [

(V/M)MW] for 2 sec. to copy

the contents of memory A45 to VFO.

• VFO mode is automatically selected.

■ Copying example 2

(118.0250 MHz, AM, B07 to F02)

q Push [V/M] to select memory mode (p. 23).

w Select the memory channel B07. (p. 24)

e While pushing [FUNC],

push [

(V/M)MW].

r While pushing [FUNC],

rotate [DIAL] to select

BANK “F”.

t Rotate [DIAL], or push

[0], [2] to select chan-

nel “02”.

y While pushing [FUNC],

push [

(V/M)MW] for 2

sec. to transfer the

contents of B07 to F02.

MEMO

WFM

A45 59.7500

59.7500

VFO

WFM

FUNC

V/M

MEMO

B07 118.0250

MEMO

MEMORY COPY

FUNC

V/M

MEMO

SET BANK

F:Aviation

FUNC

[DIAL]

MEMO

SET CH NO .

F02 BLANK

[DIAL]

MEMO

F02 118.0250

FUNC

V/M

IC-R10.qxd 02.1.10 11:44 Page 34 (1,1)

MEMORY SCAN

Repeatedly scans all programmed memory channels ex-

cept blank channels.

FULL SCAN

Repeatedly scans operatable frequency range.

SCANNING OPERATION

0.5 MHz 1300 MHz

A01

A02

A03

A04

A05

A49

B00

B01–R99

Blank

■ General

Scan types

The IC-R10 has 2 major scan types: PROGRAMMED SCAN

and MEMORY SCAN. These, in turn, can be subdivided into

3 variations of each, making a total of 6 scan operations.

Additional scanning functions are available to “fine tune”

scanning operation.

The following diagrams illustrate the operation of each scan

type.

Step-by-step instructions on how and when to use each scan

type follow these diagrams.

What is scanning?

Scanning is an automatic search function that detects signals

as it checks through a range of frequencies or memory chan-

nels.

Scanning functions are useful for discovering new frequen-

cies to listen to or for searching through previously pro-

grammed frequencies for signals.

IC-R10.qxd 02.1.10 11:44 Page 35 (1,1)

SCANNING OPERATION

PROGRAM SCAN

Repeatedly scans between two user-programmed fre-

quencies (scan edges).

BANK SCAN

Repeatedly scans all memory channels in the selected

BANK except blank channels.

AUTO-MEMORY WRITE SCAN

Same as PROGRAMMED SCAN except that paused fre-

quencies are automatically stored in memory channels

Q00–Q99.

MODE SELECT SCAN

Repeatedly scans all memory channels with the selected

receive mode.

Programmed edges

BANK "Q"

•

1234.5670

1235.6780

1235.8900

1240.0500

---------------

Programmed scan edges

A00

A01

A02

A03

A04

A05

A06

A45

Blank

A00

A01

A03

A04

A05

A06

A07

B00–R99

WFM

FM only

USB

IC-R10.qxd 02.1.10 11:44 Page 36 (1,1)

SCANNING OPERATION

■ Before scanning

Set the following conditions before

scanning.

INFORMATION

What happens when you rotate the tun-

ing dial during scanning?

While scanning—

Scanning direction is changed.

Example:

If you rotate [DIAL] counterclockwise

while scanning up (frequency/memory

channel number increase), scan

changes to down scanning (fre-

quency/memory channel number de-

crease).

While pausing—

Scanning starts again (pause is can-

celled).

1. Set receive mode

Set any receive mode EXCEPT USB,

LSB and CW.

The squelch control activates for RF

gain control while USB, LSB, or CW

mode is selected. RF gain control

does not activate for audio noise

muting, therefore, the receiver is in a

busy condition at all times. In such

case, searching speed is either very

slow or searching doesn’t even start.

2. Set the volume and

squelch levels

Set [VOL] to a suitable audio output

level.

Set [SQL] so that the noise audio is

just muted.

IC-R10.qxd 02.1.10 11:44 Page 37 (1,1)

SCANNING OPERATION

Set the VSC

Set the VSC ON if necessary.

While pushing [FUNC], push [

(2)VSC] (VSC indicator ap-

pears).

While pushing [FUNC], push [(2)VSC) to turn OFF the

VSC (VSC indicator disappears).

What is VSC?

The VSC (Voice Scanning Control) pauses a scan only

when modulated signals are received. Scanning continues

when unmodulated or beat signals are received.

Set the scan delay

Set the scan delay.

While pushing [FUNC], push

[

(CLR)SET], then push [EDIT]

one or more times until SCAN

DELAY appears (p. 62).

Rotate [DIAL] to set the scan

delay time.

Push [CLR] to return to VFO or

MEMORY mode.

What is scan delay?

Scan delay affects scan pausing as follows:

5SEC: scan automatically resumes 5 sec. after paus-

ing

10SEC: scan automatically resumes 10 sec. after

pausing

PAUSE: scan automatically resumes 2 sec. after a re-

ceived signal disappears

VSCVFO

144.0000

SIGNAVI

FUNC

Appears

IC-R10.qxd 02.1.10 11:44 Page 38 (1,1)

SCANNING OPERATION

■ Full scan

This is the simplest scanning operation, searching the full fre-

quency range (0.5–1300 MHz) in the selected receive mode

and tuning step.

Start and stop the scan

q Push [V/M] to select VFO mode. (p. 11)

w Push [SCAN] to

start scanning.

To change the direction of the scanning, rotate [DIAL]

during scanning.

When the program skip

function is ON (p. 61), fre-

quencies stored in BANK

R memories are skipped.

Also, “SKIP” is displayed.

e Push [SCAN] or [CLR] to stop scanning.

SCAN

VFO

144.0000

Flashes while scanning

VFO

144.0000

SKIP

Skip indicator

■ Memory scan

This is the simplest way to search for all stored frequencies in

memory channels.

Start and stop the scan

q Push [V/M] to select MEMORY mode.

w Push [SCAN] to

start scanning.

To change the direction of the scan, rotate [DIAL] during

scanning.

When the memory skip

function is ON (p. 61),

specified memory chan-

nels (p. 56) are skipped.

Also, “SKIP” is displayed.

e Push [SCAN] or [CLR] to stop scanning.

SCAN

MEMO

A00 144.0000

Flashes while scanning

MEMO

A00 144.0000

SKIP

Skip indicator

IC-R10.qxd 02.1.10 11:44 Page 39 (1,1)

SCANNING OPERATION

■ Program scan

This is the most useful basic scan for searching over a spec-

iﬁed frequency range.

1. Select program scan channel

q Push [V/M] to select VFO mode (p. 11).

w While pushing

[FUNC], push

[

(4)PROG-S].

Rotate [DIAL] to se-

lect the program scan

channel.

Displays “PROGRAM

SCAN” with program

channel number and

the names for 2 sec.,

then scan edges, “S”

and “E”, are dis-

played.

VFO

PROGRAM SCAN

PROG-S

FUNC

E: 146.0000

VFO

PROGRAM SCAN

VFO

S: 144.0000

[DIAL]

Displays "

S (start)" and "E

(end)" frequencies after 2

sec.

2. Start and stop scanning

Push [SCAN] to start

scanning.

To change the direction of the scan, rotate [DIAL] during

scanning.

When the program skip

function is ON (p. 61), fre-

quencies stored in BANK R

memories are skipped.

Also, “SKIP” is displayed.

Push [CLR] or [SCAN] to stop scanning.

When the same frequency is stored in both scan edges,

program scan will not proceed.

The default frequency range is 144.0000–146.0000

MHz. Set up scan frequency ranges before starting pro-

gram scan. See page 57 for program scan channel set

up.

VFO

144.0000

SCAN

Flashes while scanning

VFO

144.0000

SKIP

Skip indicator

IC-R10.qxd 02.1.10 11:44 Page 40 (1,1)

■ Auto memory write scan

This scan is useful for searching a speciﬁed frequency range

and automatically storing busy frequencies into memory

channels. The same frequency ranges used for program scan

are used for auto memory write scan.

SCANNING OPERATION

1. Select program scan channel

q Push [V/M] to select VFO mode (p. 11).

w While pushing

[FUNC], push

[

(5)AMWS].

Rotate [DIAL] to select

the program scan

channel.

Displays “PROGRAM

AMWS” with program

channel number and

the names as program

scan channel.

VFO

PROGRAM AMWS

FUNC

AMWS

E: 146.0000

VFO

PROGRAM AMWS

VFO

S: 144.0000

[DIAL]

Displays "

S (start)" and "E

(end)" frequencies after 2

sec.

2. Start and stop scanning

Push [SCAN] to start

scanning.

To change the direction of the scan, rotate [DIAL] during

scanning.

When the program skip

function is ON (p. 61), fre-

quencies stored in BANK R

memories are skipped.

Also, “SKIP” is displayed.

Push [CLR] or [SCAN] to stop scanning.

VFO

144.0000

SCAN

Flashes while scanning

VFO

144.0000

SKIP

Skip indicator

IC-R10.qxd 02.1.10 11:44 Page 41 (1,1)

SCANNING OPERATION

During auto-memory write scanning:

q Busy (paused) frequencies are automatically stored into

BANK Q memory channels.

w The scan is automatically cancelled when BANK Q be-

comes full.

e Unmodulated or beat signals may not be stored into mem-

ory channels when the VSC function is turned ON.

r While pushing [FUNC], push [

(V/M)MW] when unwanted

signals (ones you don’t want to store) are received.

For your convenience:

Auto-memory write scan automatically clears all previously

stored information when it is started. Therefore, it is a good

idea to copy desired frequency data memorized during

auto-memory write scan into BANK A to P’s memory chan-

nels before operating the scan.

IC-R10.qxd 02.1.10 11:44 Page 42 (1,1)

SCANNING OPERATION

2. Start and stop scanning

Push [SCAN] to start

scanning.

To change the scan direction, rotate [DIAL] during scan-

ning.

When the memory skip

function is ON (p. 61),

specified memory chan-

nels (p. 56) are skipped.

Also, “SKIP” is dis-

played.

Push [CLR] or [SCAN] to stop scanning.

The speciﬁed BANK must have 2 or more stored channels,

otherwise, the scan will not proceed.

MEMO

F01 121 .5000

SCAN

Flashes while scanning

■ BANK scan

Scans all stored frequencies into a speciﬁed BANK, except

for SKIP channels.

1. Select BANK scan and BANK number

q Push [V/M] to select MEMORY mode (p. 23).

w While pushing

[FUNC], push

[(8)BANK-S].

Rotate [DIAL] to se-

lect the BANK num-

ber.

Displays “BANK SCAN” with BANK number and the

names.

BANK-S

FUNC

MEMO

BANK SCAN

[DIAL]

MEMO

BANK SCAN

F:Aviation

MEMO

F01 121 .5000

SKIP

Skip indicator

IC-R10.qxd 02.1.10 11:44 Page 43 (1,1)

SCANNING OPERATION

2. Start and stop scanning

Push [SCAN] to start

scanning.

To change the scan direction, rotate [DIAL] during scan-

ning.

When the memory skip func-

tion is ON (p. 61), speciﬁed

memory channels (p. 56) are

skipped. Also, “SKIP” is

displayed.

Push [CLR] or [SCAN] to stop scanning.

If 2 or more channels do not have the specified receive

mode, scan will not proceed.

MEMO

F01 121 .5000

SCAN

Flashes while scanning

MEMO

F01 121 .5000

SKIP

Skip indicator

■ Mode select scan

Scans all stored frequencies that have the speciﬁed receive

mode, except SKIP channels.

1. Select mode select scan and mode

q Push [V/M] to select MEMORY mode (p. 23).

w While pushing

[FUNC], push

[

(7)MODE-S].

Displays “MODE SCAN”.

e Push [MODE] once

or more times to se-

lect the receive

mode.

MEMO

MODE SCAN

MODE-S

FUNC

MODE SCAN

MEMO

MODE

IC-R10.qxd 02.1.10 11:44 Page 44 (1,1)

SCANNING OPERATION

2. Program skip setting

— cont.

When BANK R becomes full, an

error beep sounds when trying to

set more skip frequencies.

When you want to cancel the skip

function, turn OFF the SKIP setting

in the memory channel (p. 56).

t After set up, push [SCAN] or

[CLR] to stop scanning.

Stored frequencies are skipped dur-

ing the next full, program or auto-

memory write scan operation.

1. Memory skip setting

Set the skip condition in each mem-

ory channel—refer to p. 55 MEM-

ORY EDIT for details.

■ Skip function

Two skip functions are available as fol-

lows:

1. Program skip function

Used with full, program and auto-mem-

ory write scans, this function allows you

to skip speciﬁed frequencies stored in

BANK R (skip function must be ON for

these channels).

2. Memory skip function

Used with memory, BANK and mode

select scans, this function allows you to

skip speciﬁed memory channels.

These are activated when PROGRAM

SKIP or MEMORY SKIP is turned

ON in set mode (p. 59).

Their factory pre-programmed settings

are:

PROGRAM SKIP : OFF

MEMORY SKIP : ON

1. Program skip setting

q Set PROGRAM SKIP to ON in

set mode (p. 59).

w Push [V/M] to select VFO mode.

(p. 11)

e Start full or program scan (p. 35).

r While pushing

[FUNC], push

[

(V/M)MW] dur-

ing scan pause

if you want to

skip the paused

frequency.

Skip frequencies

are stored in

BANK-R memory

channels (count-

ing down from

channel 99 to 00).

PROGRAM SKIP

IC-R10.qxd 02.1.10 11:44 Page 45 (1,1)

SCANNING OPERATION

2. Select scan type and

start scanning

q While pushing [FUNC], push

[

(4)PROG-S] for program scan or

[

(5)AMWS] for auto-memory write

scan, then rotate [DIAL] to select

scanning frequency band.

•Conﬁrm that the receive mode of

the selected scan band is FM and

also that the tuning step is equal

to or smaller than 20 kHz.

•If you want to search the entire

frequency range (0.5–1300 MHz)

skip this step.

w Push [SCAN] to start scanning.

e Push [SCAN] or [CLR] to stop

scanning.

■ SIGNAVI function

The SIGNAVI function activates while

paused during full, program or auto-

memory write scans in FM mode. It

searches for busy frequencies up to

100 kHz* (+100 kHz when scanning up,

–100 kHz when scanning down) from

the paused frequency (f

0), then jumps

to the next busy frequency (f

1) detected

(by SIGNAVI) when scan resumes.

*The SIGNAVI search range varies ac-

cording to tuning step settings. The

maximum range is 5 channels or steps

from the receive frequency, therefore,

the tuning step must be equal to or

smaller than 20 kHz.

1. Set SIGNAVI function

q Push [V/M] to select VFO mode

(p. 11).

w While pushing [FUNC], push

[

(6)SIGNAVI].

•Displays “SIGNAVI” below fre-

quency.

SIGNAVI

VFO

144.0000

SIGNAVI

FUNC

SCAN

VFO

144.0000

Flashes while scanning

IC-R10.qxd 02.1.10 11:44 Page 46 (1,1)

PRIORITY WATCH

MEMORY CHANNEL WATCH

While listening to a selected

memory channel, priority

watch checks for signals on

the priority frequency every 5

sec.

•When the selected memory

channel is masked (blank), the

the watch does not start.

•SKIP memory channels can be

selected.

VFO FREQUENCY WATCH

While listening to a VFO fre-

quency, priority watch checks

for signals on the priority fre-

quency every 5 sec.

VFO

A01

■ General

What is priority watch?

Priority watch checks for signals on a priority frequency while

listening to another frequency or, while searching one or more

frequencies or memory channels.

When receiving a signal on the priority channel, priority watch

pauses for 5 sec.

This function is useful when you want to monitor for a signal

that appears infrequently. In this case, you can wait for the

signal while listening to another signal on a different fre-

quency.

Types of priority watch

There are two basic priority watches: VFO FREQUENCY

WATCH and MEMORY CHANNEL WATCH. Also, the priority

watch can be activated in conjunction with a scanning func-

tion, thereby making a total of 8 priority watch operations.

The following diagrams illustrate the operation of each priority

watch type.

IC-R10.qxd 02.1.10 11:44 Page 47 (1,1)

PRIORITY WATCH

MEMORY SCAN/BANK SCAN/MODE SELECT SCAN WATCH

While scanning all or selected memory channels, priority watch

checks for signals on the priority frequency every 5 sec.

• When the skip function is ON, skips speciﬁed memory channels.

•When the selected BANK or receive mode is not memorized, priority

watch does not start.

FULL SCAN WATCH/PROGRAM SCAN/AUTO-MEMORY WRITE SCAN WATCH

While scanning the full frequency range or a programmed fre-

quency range, priority watch checks for signals on the priority fre-

quency every 5 sec.

• When the skip function is ON, skips speciﬁed frequencies.

•The priority frequency is never programmed into BANK Q even if a signal

is received on the priority frequency when auto-memory write scan is se-

lected.

A01

A32

IC-R10.qxd 02.1.10 11:44 Page 48 (1,1)

PRIORITY WATCH

2. Set MAIN frequency

Set the frequency in VFO mode (pgs. 14, 15) or select the

memory channel (p. 24) you want to listen to with the prior-

ity channel, or start scanning (p. 35).

While pushing [FUNC], push [

(9)PRIO], or push [CLR] only

to stop priority watch.

1. Program a priority channel

144.0000 MHz is initially programmed by default.

q Select the frequency

you want to program

into the priority

channel in VFO

mode (p. 11) or MEMORY mode (p. 23).

w While pushing

[FUNC], push

[

(9)PRIO] for 2 sec.

Start priority watch

automatically.

MEMO

F01 121 .5000

(ex.)

V/M

MEMO

F01 121 .5000

144 .0000

MEMO

121 .5000

PRIO SET

MEMO

121 5000

PRIO

FUNC

after beep

after 2 sec.

121 .5000

121 5000

(ex.)

VFO

WFM

59.7500

59 7500

Flashes when priority

watch is selected scanning

Appears while watching

frequency or band

IC-R10.qxd 02.1.10 11:44 Page 49 (1,1)

EASY MODE

2. Select frequency range

and start scanning

q Push a numeral key to select a

frequency range to search.

w Push [SCAN] to

start scanning.

e Push [SCAN] or

[CLR] to stop

scanning.

EASY

0: 0.5000

SCAN

Flashes while scanning

■ EASY mode operation

1. Select EASY mode

Push [EASY] to select EASY mode.

EASY

0: 0.5000

EASY

Appears

■ General

The IC-R10 has an EASY mode which

provides simple operation by only scan-

ning programmed frequency ranges.

When you select EASY mode, 1 of 10

pre-programmed frequency ranges can

be selected.

10 different frequency ranges are pro-

grammed for EASY mode operation in

some transceiver versions; however,

0.5–1300.0000 MHz with FM receive

mode is pre-programmed into all 10

channels in other versions.

Settings for each range are program-

mable. See page 55, before you oper-

ate in EASY mode, in case EASY mode

doesn’t have the frequency ranges you

want or when you want to set up pre-

ferred conditions.

IC-R10.qxd 02.1.10 11:44 Page 50 (1,1)

EDIT FUNCTION

■ Memory channel edit

You can store the following items into a memory channel:

1. Frequency settings: (SET FREQ)

Memorized frequencies can be edited or erased.

2. Channel names: (SET CH NAME)

Alphanumeric names can be input or edited. (Up to 8

characters per name.)

3. Receive mode: (SET MODE)

Receive mode can be speciﬁed.

4. SKIP setting: (SET SKIP)

SKIP settings can be toggled ON or OFF for memory

skip scan (pgs. 39, 43, 44).

5. Attenuator setting: (SET ATT)

Attenuator settings can be toggled ON or OFF.

6. BANK names: (SET B-NAME)

Alphanumeric names can be input or edited. (Up to 10

characters per name.)

■ General

The edit function is used for arranging memorized contents

into the following channels:

Memory channels

Program/auto-memory write scan channels

EASY mode channels

IC-R10.qxd 02.1.10 11:44 Page 51 (1,1)

EDIT FUNCTION

Memory channel edit ﬂow chart

MEMO

SET FREQ

144.0000

MEMO

SET CH NAME

A00

MEMO

SET MODE

MODE:FM

MEMO

SET SKIP

SKIP: OFF

MEMO

SET ATT

ATT: OFF

MEMO

SET B-NAME

MEMO

A00 144 .0000

CLR

EDIT

Push for 2 sec.

Fixed contents will be cleared.

IC-R10.qxd 02.1.10 11:44 Page 52 (1,1)

EDIT FUNCTION

■ Memory channel edit

1. Enter memory edit

mode

q Push [V/M] to select MEMORY

mode, then select the memory

channel (pgs. 23, 24).

w Push [EDIT] to enter memory edit

mode.

3. Set channel names

q Enter channel

names via the

keypad or by ro-

tating [DIAL].

•When you enter

channel names

from the [DIAL] or a

character assigned

in the same key,

push [ENT] before

you enter the next

character to

change the digit

(see page 72 for al-

phanumeric key as-

signment).

w Push [EDIT] to change the item.

MEMO

SET CH NAME

A00 :

[DIAL]

2. Set frequency

q Enter the frequency via the key-

pad or by rotating [DIAL].

w Push [EDIT] to change the item.

MEMO

SET FREQ

144.0000

[DIAL]

digit

keys

IC-R10.qxd 02.1.10 11:44 Page 53 (1,1)

EDIT FUNCTION

4. Set receive mode and

skip condition

q Rotate [DIAL] to select receive

mode.

w Push [EDIT] to change the item.

e Rotate [DIAL] to select skip condi-

tion.

r Push [EDIT] to change the item.

5. Set attenuator

condition

q Rotate [DIAL] to select attenuator

condition.

w Push [EDIT] to change the item.

6. Set BANK names

q Enter BANK names from the key-

pad or via [DIAL] as for channel

name setting (see page 72 for al-

phanumeric key assignments).

w Push and hold [EDIT] to enter the

ﬁxed contents.

• Push [EDIT] one or more times to

conﬁrm the entered contents, or push

[CLR] to cancel all entered contents,

if required.

MEMO

SET MODE

MODE:FM

[DIAL]

MEMO

SET SKIP

SKIP: OFF

[DIAL]

MEMO

SET ATT

ATT: OFF

[DIAL]

MEMO

SET B-NAME

[DIAL]

digit

keys

IC-R10.qxd 02.1.10 11:44 Page 54 (1,1)

EDIT FUNCTION

■ Program scan channel edit

Arrange memorized contents into program scan channels 00

to 19.

You can edit the following items:

1. Channel names: (SET CH NAME)

Set channel names for programmed frequency range; up

to 8 characters per name.

2. Scan band edge 1: (START FREQ)

Set the start frequency for scan frequency range.

3. Scan band edge 2: (END FREQ)

Set the end frequency for scan frequency range.

4. Receive mode: (SET MOD)

Select a receive mode.

5. Tuning step: (SET TS)

Select or program a tuning step.

6. Scan delay time: (SCAN DELAY)

Select the scan delay (pausing) time.

■ EASY mode channel edit

Arrange memorized contents in EASY mode channels 0 to 9.

You can edit the following items:

1. Channel names: (SET CH NAME)

Set channel names for programmed frequency range; up

to 8 characters per name.

2. Scan band edge 1: (START FREQ)

Set the start frequency for scan frequency range.

3. Scan band edge 2: (END FREQ)

Set the end frequency for scan frequency range.

4. Receive mode: (SET MOD)

Select a receive mode.

5. Tuning step: (SET TS)

Select or program a tuning step.

6. Scan delay time: (SCAN DELAY)

Select the scan delay (pausing) time.

IC-R10.qxd 02.1.10 11:44 Page 55 (1,1)

EDIT FUNCTION

Program/auto-memory write scan and EASY mode channel edit ﬂow chart

START FREQ

EASYVFO

144.0000

END FREQ

EASYVFO

146.0000

EASYVFO

SET CH NAME

EASYVFO

SET MODE

MODE:FM

EASYVFO

SCAN DELAY

5SEC

EASYVFO

SET TS

TS 5.00kHz

VFO

S: 144 .0000

E: 146 .0000

EASY

0: 144.0000

EDIT

CLR

EDIT

Push for 2 sec.

Fixed contents will be cleared.

IC-R10.qxd 02.1.10 11:44 Page 56 (1,1)

EDIT FUNCTION

■ Program scan or EASY mode channel edit

1. Enter edit mode

q Push [V/M] or [EDIT] to select

VFO or EASY mode (p. 11 or 50).

w While pushing [FUNC], push

[

(4)PROG-S] or [(5)AMWS] to se-

lect program or auto-memory write

scan mode; then select the scan

channel (pgs. 40, 41) when VFO

mode is selected in q, push digit

key to select scan channel when

EASY mode is

selected in q.

e Push [EDIT]

to enter

memory edit

mode.

3. Set start frequency

q Enter the start frequency via the

keypad or [DIAL].

w Push [EDIT] to change the item.

2. Set channel names

q Enter channel

names from the

keypad or by ro-

tating [DIAL].

•When you enter

channel names

with [DIAL] or a

character assigned

to the same key,

push [ENT] before

you enter the next

character to

change the digit

(see page 72 for

alphanumeric key

assignments).

w Push [EDIT] to change the item.

EASYVFO

144.0000

START FRQ

[DIAL]

digit

key

either

EASYVFO

SET CH NAME

[DIAL]

digit

key

either

IC-R10.qxd 02.1.10 11:44 Page 57 (1,1)

EDIT MODE

4. Set end frequency

q Enter the start frequency via the

keypad or [DIAL].

w Push [EDIT] to change the item.

5. Set receive mode and

tuning step

q Rotate [DIAL] to select receive

mode.

w Push [EDIT] to change the item.

e Rotate [DIAL] to select skip condi-

tion.

r Push [EDIT] to change the item.

6. Set scan delay time

q Rotate [DIAL] to select scan delay

time.

w Push and hold [EDIT] to enter the

set contents.

• Push [EDIT] one or more times to

confirm the set contents, or push

[CLR] to cancel, if desired.

END FRQ

EASYVFO

146.0000

[DIAL]

digit

key

either

EASYVFO

SET MODE

MODE:FM

[DIAL]

either

EASYVFO

SET TS

TS 5.00kHz

[DIAL]

either

EASYVFO

SCAN DELAY

5SEC

[DIAL]

either

IC-R10.qxd 02.1.10 11:44 Page 58 (1,1)

SET MODE

MESSAGE

BEEP

CONTRAST

LOW HI

LIGHT

AUTO 5SEC

PROGRAM SKIP

OFF

MEMORY SKIP

POWER SAVE

1:4

SCAN DELAY

5SEC

CI-V ADDRESS

CI-V BAUD

9600

CI-V TRN

VFO

144.0000

MEMO

A00 144 .0000

CLR

SET

FUNC

CLR

EASY

0: 0.5000

Set mode ﬂow chart

■ General

What is SET mode?

SET mode is accessed from VFO,

MEMORY or EASY mode and allows

you to modify certain receiver condi-

tions to suit your operating require-

ments.

Adjusting these settings to your own in-

dividual preferences allows you to “cus-

tomize” the receiver’s operating

parameters to suit your operating style.

If you are not sure what effect changing

a particular condition will have on the

receiver’s performance—experiment

with different settings. Don’t worry, there

is no way you can damage the receiver

by altering these settings.

There are 11 conditions which can be

modiﬁed in SET mode. The displays at

right show the initial or all reset (p. 70)

conditions. See the following pages for

an example of each condition and how

to modify them.

IC-R10.qxd 02.1.10 11:44 Page 59 (1,1)

SET MODE

Entering SET

mode

While pushing [FUNC],

push [

(CLR)SET] to enter

SET mode.

Push [EDIT] to select next

item.

Opening message

Rotate [DIAL] to toggle

opening message ON or

OFF.

OFF

MESSAGE

Beep audio

Rotate [DIAL] to set beep

audio ON or OFF.

BEEP

OFF

BEEP

Display contrast

Rotate [DIAL] to adjust the

LCD contrast to a suitable

level.

CONTRAST

LOW HI

CONTRAST

LOW HI

CONTRAST

LOW HI

CONTRAST

LOW HI

IC-R10.qxd 02.1.10 11:44 Page 60 (1,1)

SET MODE

Memory skip

condition

Rotate [DIAL] to toggle the

memory skip scan condi-

tion ON or OFF.

MEMORY SKIP

OFF

MEMORY SKIP

Power save

condition

Rotate [DIAL] to select the

power save ratio or turn

the function OFF.

POWER SAVE

1:4

POWER SAVE

1:16

POWER SAVE

OFF

Backlight

condition

Rotate [DIAL] to set LCD

and key backlight condi-

tions.

LIGHT

AUTO 5SEC

LIGHT

OFF

LIGHT

Program skip

condition

Rotate [DIAL] to toggle the

program skip scan condi-

tion ON or OFF.

PROGRAM SKIP

OFF

PROGRAM SKIP

IC-R10.qxd 02.1.10 11:44 Page 61 (1,1)

SET MODE

Scan delay

condition

Rotate [DIAL] to set the

scan pausing time.

SCAN DELAY

5SEC

SCAN DELAY

10SEC

SCAN DELAY

PAUSE

CI-V address

Rotate [DIAL] to select the

CI-V address from 01 to

7F.

CI-V ADDRESS

CI-V baud

Rotate [DIAL] to select CI-

V baud from

300, 1200,

4800, 9600 and 19200

bps.

1200 bps is the optimum

baud rate for CI-V control.

CI-V BAUD

300

1200

4800

CI-V BAUD

9600

CI-V BAUD

19200

CI-V transceive

Rotate [DIAL] to toggle CI-

V transceive function ON

or OFF.

CI-V TRN

OFF

CI-V TRN

IC-R10.qxd 02.1.10 11:44 Page 62 (1,1)

OTHER FUNCTIONS

Setting AFC

While pushing [FUNC], push [(.)AFC] to toggle the AFC

function ON and OFF.

■ AFC function

The AFC (Automatic Frequency Control) function tunes the

displayed frequency automatically when an off-center fre-

quency is received. It activates in FM modes only.

VFO

AFCFM

144.0000

Appears

AFC

FUNC

■ Low battery indicator

The low battery indicator activates when the installed batter-

ies fall to a speciﬁed voltage level. The receiver emits beeps

and displays “LOW BATTERY” to inform you that battery ca-

pacity is low. Beeps sound once every 10 sec. and are syn-

chronized with the beep setting in SET mode (p. 60).

VFO

144.0000

LOW BATTERY

appears once every 5 sec.

IC-R10.qxd 02.1.10 11:44 Page 63 (1,1)

OTHER FUNCTIONS

Set monitor

While pushing [MONI], squelch mute is released; when the

VSC function is ON, both squelch and VSC mute are re-

leased.

■ Monitor function

The monitor function releases the squelch or VSC mute mo-

mentarily when very weak signals are received without having

to re-adjust the squelch manually.

Set lock

While pushing [FUNC], push [(EDIT)LOCK] to toggle the

lock function ON and OFF.

All switches and controls are electronically locked except

for [POWER], [MONI] and [FUNC].

■ Lock function

The lock function is available so that you can listen to one fre-

quency continuously and not worry about accidentally chang-

ing it or activating an undesired function.

VFO

144.0000

Appears

EDIT

LOCK

FUNC

IC-R10.qxd 02.1.10 11:44 Page 64 (1,1)

OTHER FUNCTIONS

Set ATT

While pushing [FUNC], push [(0)ATT] to toggle the ATT

function ON and OFF.

■ ATT function

The ATT (attenuator) function protects desired signals from

distorting when excessively strong signals, such as broad-

cast, pager signals, etc. are nearby. This setting can be mem-

orized into memory channels.

AT TVFO

144.0000

Appears

ATT

FUNC

Set NB/ANL

While pushing [FUNC], push [(ENT)NB/ANL] to toggle the

NB or ANL function ON and OFF.

■ NB/ANL function

The NB (noise blanker) function removes pulse-type noise

when USB, LSB or CW is selected. The ANL (automatic

noise limiter) function reduces noise components when AM

is selected.

VFO

118.0000

ANL

Appears

ENT

NB/ANL

FUNC

VFO

USB

14.1950

Appears

ENT

NB/ANL

FUNC

IC-R10.qxd 02.1.10 11:44 Page 65 (1,1)

OTHER FUNCTIONS

Set sleep timer

q While pushing [FUNC], push [(3)SLEEP] one or more times to set the sleep timer

condition.

w Release [FUNC] to set the selected condition.

e When the speciﬁed time elapses, the receiver emits 5 beeps then powers OFF.

*When you want to

use the sleep timer

function in EASY

mode—set it in VFO

or MEMORY mode

ﬁrst, then enter EASY

mode.

■ Sleep timer function*

The sleep timer activates after a speciﬁed time elapses, automatically turning the re-

ceiver power OFF.

VFO

60min

SLEEP TIMER

VFO

40min

SLEEP TIMER

VFO

20min

SLEEP TIMER

VFO

WFM

SLEEP TIMER

OFF

SLEEP

FUNC

VFO

144.0000

Appears

release [FUNC]

■ User TS setting

The user programmable tuning step al-

lows you to set optimum tuning steps

for specific channel spacing using the

[DIAL].

Set tuning step

q Enter tuning step set mode (p.

13), then rotate [DIAL] until

“USER TS” appears.

w Enter the desired tuning step

using the numeral keys (including

the decimal key, if necessary).

•User tuning step is selectable

from 0.1 kHz to 999.90 kHz (0.1

kHz step).

e Push [CLR] to set tuning step and

return to VFO.

VFO

USER TS

TS 5.00kHz

User TS default setting

IC-R10.qxd 02.1.10 11:44 Page 66 (1,1)

OTHER FUNCTIONS

Enter memory channel names

Enter memory channel names via the keypad or [DIAL].

•When you enter channel names with [DIAL] or a character as-

signed to the same key, push [ENT] before you enter the next

character to change the digit (see page 72 for alphanumeric key

assignments).

Refer to memory edit for entering alphanumeric characters.

■ Memory search function

The memory search function searches memory channels

using channel names. This is useful for recalling memory

channels when you forget their channel number.

[DIAL]

MEMO

NAME SEARCH

(ex.)

Enter memory search mode

q Push [V/M] to select MEMORY mode (p. 23).

w While pushing [FUNC], push [

(EASY)SEARCH].

MEMO

NAME SEARCH

EASY

FUNC

IC-R10.qxd 02.1.10 11:44 Page 67 (1,1)

OTHER FUNCTIONS

Searching

Push [SCAN] to start memory channel search.

• Only the first one or two characters are needed to start a

search. Smaller channel numbers are displayed ﬁrst in cases

where two or more channels start with the same characters.

• Push [SCAN] again to display the next candidate in a search.

Selecting a memory channel

Push [ENT] to select a memory channel.

MEMO

F01 121 .5000

ENT

MEMO

NAME SEARCH

F01:EMER.

MEMO

NAME SEARCH

F01:EMER.

MEMO

NOT FOUND

when matching channel is found

when no match is found

IC-R10.qxd 02.1.10 11:44 Page 68 (1,1)

OTHER FUNCTIONS

Set auto mode

Push [MODE] one or more times, in VFO mode, until

“AUTO MODE” appears, then push [CLR] to return to VFO

mode.

■ Auto mode and TS function

The auto receive mode select and auto tuning step select

functions are optionally available. This function can be set up

and modiﬁed by programming from a computer using the op-

tional CS-R10

CLONING SOFTWARE

. Some versions may be

pre-programmed.

The auto tuning step and receive mode select functions can

be set up by dividing the operatable frequency range into up

to 15 bands. For details contact your nearest dealer or local

distributor.

VFO

144.0000

AUTO MODE

MODE

Set auto TS

While pushing [FUNC], push [(MODE)TS] in VFO mode,

then rotate [DIAL] to select “TS AUTO”

VFO

SET TS

TS AUTO

[DIAL]

IC-R10.qxd 02.1.10 11:44 Page 69 (1,1)

OTHER FUNCTIONS

■ Resetting the CPU

There are 2 ways to reset the CPU as

follows:

PARTIAL RESET:

When you want to initialize the operat-

ing conditions (VFO frequency, VFO

settings, SET mode contents) without

clearing the memory, program scan,

EASY mode and auto TS/mode set-

tings, a partial reset function is available

for the receiver.

ALL RESET:

Use this option when the CPU malfunc-

tions.

CAUTION: Resetting the CPU returns

all programmed contents to their default

settings.

Partial reset

q Turn power OFF.

w While pushing

[MODE], push

[POWER] for

1 sec. to turn

power ON.

e Rotate [DIAL] to

select ”YES” or

“NO”, then push

[ENT].

A partial reset is

performed when

”YES” is selected;

selecting “NO”

cancels the opera-

tion.

All reset

q Turn power OFF.

w While pushing

[CLR], push

[POWER] for 1

sec. to turn

power ON.

e Rotate [DIAL] to

select ”YES” or

“NO”, then push

[ENT].

An all reset is per-

formed when

”YES” is selected;

selecting “NO”

cancels the opera-

tion.

MODE

POWER

PARTIAL ?

ALL-RESET ?

POWER

CLR

IC-R10.qxd 02.1.10 11:44 Page 70 (1,1)

OTHER FUNCTIONS

■ Data cloning

The IC-R10 has receiver-to-receiver

data cloning capability. This function is

useful when you want to copy all of the

programmed contents from one

IC-R10 to another.

An optional OPC-474

CLONING CABLE

is required.

In addition, the optional CS-R10

CLONING SOFTWARE is available to

clone and edit contents using a PC.

Set cloning mode and start cloning

q Turn power OFF.

w While pushing [V/M], push

[POWER] for 1 sec. to enter

cloning mode.

e Connect an optional OPC-474 be-

tween both [SP] jacks.

r Push [FUNC] on the “master” re-

ceiver (receiver-to-receiver cloning

only).

OPC-474

CLONE MODE

POWER

V/M

CLONE OUT

CLONE END

FUNC

IC-R10.qxd 02.1.10 11:44 Page 71 (1,1)

ALPHANUMERIC KEY ASSIGNMENT

Keypad

Input

Corresponding Alphanumeric Character

No modiﬁer key While pushing [FUNC]

Q (Q), Z(Z), 1(1) q (q), z(z), 1(1)

A (A), B(B), C(C), 2(2) a (a), b(b), c(c)2(2)

D (D), E(E), F(F), 3(3) d (d), e(e), f(f), 3(3)

G (G), H(H), I(I), 4(4) g (g), h(h), i(i), 4(4)

J (J), K(K), L(L), 5(5) j (j), k(k), l(l), 5(5)

M (M), N(N), O(O), 6(6) m (m), n(n), o(o), 6(6)

P (P), R(R), S(S), 7(7) p (p), r(r), s(s), 7(7)

T (T), U(U), V(V), 8(8) t (t), u(u), v(v), 8(8)

W (W), X(X), Y(Y), 9(9)

w (w), x(x), y(y), 9(9)

0 (0) 0(0)

(space), . (period),

, (comma), - (hyphen)

(space), . (period),

, (comma), - (hyphen)

NOTE: In addition to the characters listed in the table at left,

the following characters are available when using [DIAL] for

alphanumeric input:

!(exclamation mark) "(double quotation mark)

#(number) $(dollar sign)

%(percent sign) &(ampersand)

'(single quotation mark) ((left parenthesis)

)(right parenthesis) *(asterisk)

+(plus sign) /(slash)

:(colon) ;(semi-colon)

<(left angle bracket) =(equals sign)

>(right angle bracket) ?(question mark)

@(at symbol) [(left bracket)

\(yen symbol) ](right bracket)

^(caret) _(under score)

`(grave accent) {(left brace)

|(bar) }(right brace)

IC-R10.qxd 02.1.10 11:44 Page 72 (1,1)

CONTROL COMMANDS

■ General

The IC-R10 can be connected to a PC via the PC’s RS-232C

port using an optional CT-17

CI-V LEVEL CONVERTOR

. This

allows you to control the receiver from the PC and/or transfer

data from the receiver to the PC.

Control is provided via Icom’s CI-V Communication Interface.

■ Data format

The CI-V system can be operated using the following data

formats. Data formats differ according to command numbers.

A data area is added for some commands.

Controller ➡ IC-R10

IC-R10 ➡ Controller

q Preamble code (ﬁxed)

w Receiver’s default address

e Controller’s default address

r Command number (see table below)

t Sub command number (see table below)

y BCD code data for frequency entry

u End of message code (ﬁxed)

■ Command table

FE FE 52 E0 Cn Sc Data area FD

q wert y u

FE E0 52 Cn Sc Data area FD

q ewrt y u

Description Cn Sc

Transfers frequency data (transceive) 00 —

Transfers mode data (transceive) 01 —

Reads display frequency 03 —

Reads display mode 04 —

Sets frequency data 05 —

Sets LSB mode

Sets USB mode 01

Sets AM mode 02

Sets CW mode 03

Sets FM mode 05

Sets WFM mode 06

Reads squelch condition (open or closed)

Reads S-meter level 02

IC-R10.qxd 02.1.10 11:44 Page 73 (1,1)

CONTROL COMMANDS

CT-17

Power supply

9–15VDC

RS-232C

cable

IC-R10

to [CI-V]

Computer

Optional

BC-25

CI-V connection example

IC-R10.qxd 02.1.10 11:44 Page 74 (1,1)

TROUBLESHOOTING

If your receiver seems to be malfunctioning, please check the

following points before sending it to a service center.

PROBLEM POSSIBLE CAUSE SOLUTION REF.

No power comes on. • The installed batteries are exhausted.

(A slight current ﬂows in the circuits even when

the power is OFF.)

•The batteries have been installed in reverse po-

larity.

•Charge the batteries or place new dry cell batter-

ies in the battery case.

(Remove the batteries if you will not be using the

receiver for a long time.)

• Re-install the batteries in the correct orientation.

p. 8

No audio is output. •[VOL] is turned to the minimum position.

• Earphone or headphone is connected.

• The [SQL] is turned too far clockwise.

• VSC function is activated.

•Turn [VOL] to a suitable level.

• Disconnect the earphone or headphone.

• Turn the [SQL] counterclockwise.

• Release the VSC function.

p. 10

p. 11

p. 38

Weak reception, excessive

distortion or too much

noise.

•Not centered on the frequency.

• Wrong receive mode is selected.

• ATT function is activated.

•The [SQL] (RF gain) is set too far clockwise (when

USB, LSB or CW is selected).

• Batteries are nearly exhausted.

•Set to the center frequency using a small tuning

step.

• Select the correct receive mode.

• Release the ATT function.

• Turn the [SQL] (RF gain) counterclockwise.

•Charge the batteries or place new dry cell batter-

ies in the battery case.

p. 13

p. 12

p. 65

p. 11

p. 8

Cannot tune frequency via

the keypad or [DIAL]

•Lock function is ON. •While pushing [FUNC], push [(EDIT)

LOCK] to turn

the lock function OFF.

p. 64

Cannot charge the installed

Ni-Cd batteries.

•[CHARGE] is set to the OFF position. •Set [CHARGE] to the ON position. p. 8

IC-R10.qxd 02.1.10 11:44 Page 75 (1,1)

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION REF.

Cannot start scanning. • [SQL] is rotated too far clockwise.

•Incorrect receive mode (LSB, USB or CW) is se-

lected.

•Scan edges are set to the same frequencies.

•2 or more memory channels have not been pro-

grammed.

•No channels have been programmed with the se-

lected receive mode (when using mode select

scan).

•Rotate [SQL] counterclockwise.

• Set receive mode to one of FM, WFM or AM.

• Set scan edges to different frequencies.

•Program 2 or more memory channels.

•Program at least 2 channels with the selected re-

ceive mode.

p. 11

p. 12

p. 57

pgs. 25,

26, 27

pgs. 25,

26, 27

Cannot recall memory

channels.

•Wrong operating mode is selected. •Push [V/M] to select memory mode. p. 23

WFM signal is distorted. •Not tuned to the proper frequency. •Set the frequency 30–50 kHz less. p. 20

IC-R10.qxd 02.1.10 11:44 Page 76 (1,1)

SPECIFICATIONS

GENERAL

Frequency coverage : (Unit: MHz)

Tuning steps :

0.1, 0.5, 1, 5, 6.25, 8, 9, 10, 12.5, 15,

20, 25, 30, 50 and 100 kHz

or user programmable

(0.1–999.99

kHz/0.1 kHz steps)

Number of mem. channels : 1000

Receive modes : FM, AM, WFM, USB, LSB, CW

Antenna connector : BNC (50 Ω)

Power supply requirement : 4.8 V DC [4 AA (R6) Ni-Cd cells];

4.8–16 V DC acceptable

(negative ground)

Current drain (at 13.5 V DC) :

Rated audio 180 mA typ.

Stand-by 110 mA typ.

Power saved 38 mA typ.

Usable temperature range : –10˚C to +50˚C (+14˚F to +122˚F)

Scan speed : 16.7 ch/sec. (programmed)

6.25 ch/sec. (memory)

Dimensions :

58.5(W) × 130(H) × 31.3(D) mm

2.3(W) × 5.1(H) × 1.2(D) in

Weight : 310 g; 10.9 oz.

CI-V connector : 3-conductor 3.5 (d) mm (

/8 in)

RECEIVER

Receive system : Triple-conversion superheterodyne

Intermediate frequencies :

1st 266.7 MHz (340.0000–999.9999MHz)

429.1 MHz (except above freq.)

2nd 10.7 MHz

3rd 455 kHz

Sensitivity :

Squelch sensitivity :

Selectivity :AM, FM More than 15 kHz/6 dB

SSB More than 4 kHz/6 dB

WFM More than 150 kHz/6 dB

Audio output power :More than 120 mV at 10 % distortion

with an 8 Ω load

External speaker connector : 3-conductor 3.5 (d) mm (

/8 in)

Version Frequency Range

U.S.A.

0.5000– 823.9999

849.0001– 868.9999

894.0001–1300.0000

Europe 0.5000–1300.0000

France

0.5000– 87.5000

108.0000–1300.0000

Freq. (MHz) FM

0.5– 4.9999 0.5 µV

75– 199.9999

0.32 µV

5– 74.9999

900–1300.0000

200– 339.9999 0.45 µV

340– 699.9999 0.35 µV

700– 799.9999 0.79 µV

WFM

—

1.0 µV

2.2 µV

1.3 µV

2.0 µV

1.6 µV

1.0 µV

1.6 µV

1.4 µV

2.0 µV

SSB/CW

0.4 µV

0.25 µV

—

0.4 µV

0.32 µV

0.63 µV

800– 899.9999

0.5 µV

1.6 µV

1.6 µV 0.4 µV

Freq. (MHz) FM

0.5– 4.9999 0.5 µV

75– 199.9999

0.32 µV

5– 74.9999

900–1300.0000

200– 339.9999 0.45 µV

340– 699.9999 0.35 µV

700– 799.9999 0.79 µV

WFM

—

1.0 µV

2.2 µV

1.3 µV

2.0 µV

1.6 µV

1.0 µV

1.6 µV

1.4 µV

2.0 µV

—

800– 899.9999

0.5 µV

1.6 µV

All stated speciﬁcations are subject to change without notice

or obligation.

IC-R10.qxd 02.1.10 11:44 Page 77 (1,1)

OPTIONS

• CS-R10

CLONING SOFTWARE

+ OPC-478

CLONING CABLE

Allows you to transfer data from memories, etc., quickly and

easily edit and store data via an IBM compatible PC.

• LC-140

CARRYING CASE

Protects the receiver from everyday wear and tear.

• CT-17

V LEVEL CONVERTOR

For receiver remote control using an IBM compatible per-

sonal computer.

• HP-4

HEADPHONE

/SP-13

EARPHONE

Provides increased readability of signals in noisy environ-

ments and listening privacy.

• CP-12L

CIGARETTE LIGHTER CABLE WITH NOISE FILTER

Allows you to operate the receiver through a 12 V cigarette

lighter socket.

• OPC-254L

POWER CABLE

Allows you to operate the receiver with 4.5 to 16 V external

DC power.

• OPC-474

CLONING CABLE

Allows you to transfer data between receivers.

IC-R10.qxd 02.1.10 11:44 Page 78 (1,1)

A-5410H-1EX-t

Printed in Japan

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan

IC-R10.qxd 02.1.10 11:44 Page 79 (1,1)

Icom IC-R10 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info