12496
37
Verklein
Vergroot
Pagina terug
1/47
Pagina verder
INSTRUCTION MANUAL
iF44GT/GS
UHF TRANSCEIVER
iF34GT/GS
VHF TRANSCEIVER
IC-F34_44GT_GS-1.qxd 04.9.24 10:32 AM Page a (1,1)
i
EXPLICIT DEFINITIONS
R CAUTION! NEVER hold the transceiver so that the
antenna is very close to, or touching exposed parts of the
body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm
away from the lips and the transceiver is vertical.
R CAUTION! NEVER operate the transceiver with a
headset or other audio accessories at high volume levels.
R CAUTION! NEVER short the terminals of the bat-
tery pack.
DO NOT push PTT when not actually desiring to transmit.
AVOID using or placing the transceiver in direct sunlight or
in areas with temperatures below –25°C or above +55°C.
The basic operations, transmission and reception of the trans-
ceiver are guaranteed within the specified operating temper-
ature range. However, the LCD display may not be operate
correctly, or show an indication in the case of long hours of
operation, or after being placed in extremely cold areas.
PRECAUTION
WORD DEFINITION
RWARNING
Personal injury, fire hazard or electric shock
may occur.
CAUTION
Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
READ ALL INSTRUCTIONS carefully and com-
pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL This
instruction manual contains important operating instructions
for the IC-F34GT/GS VHF TRANSCEIVER and IC-F44GT/GS
UHF TRANSCEIVER.
IMPORTANT
Icom, Icom Inc. and the logo are registered trademarks of Icom
Incorporated (Japan) in the United states, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
SmarTrunk II™ and SmarTrunk 3G™ are Trademark of SmarTrunk Systems,
Inc.
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page i (1,1)
ii
DO NOT modify the transceiver for any reason.
KEEP the transceiver from the heavy rain, and Never
immerse it in the water. The transceiver construction is water
resistant, not waterproof.
The use of non-Icom battery packs/chargers may impair
transceiver performance and invalidate the warranty.
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page ii (1,1)
iii
IMPORTANT ........................................................................ i
EXPLICIT DEFINITIONS ..................................................... i
PRECAUTION ..................................................................... i
TABLE OF CONTENTS ...................................................... iii
1 ACCESSORIES ......................................................... 1–3
Supplied accessories ................................................. 1
Accessory attachments .............................................. 1
2 PANEL DESCRIPTION ........................................... 4–10
Front panel ................................................................. 4
Function display ......................................................... 6
Programmable function keys ..................................... 7
3 BASIC OPERATION .............................................. 11–15
Turning power ON .................................................... 11
Channel selection ..................................................... 11
Call procedure........................................................... 12
Receiving and transmitting........................................ 12
User Set mode .......................................................... 15
Scrambler function .................................................... 15
4 BIIS OPERATION .................................................. 16–27
Default setting .......................................................... 16
Receiving a call ........................................................ 16
Transmitting a call .................................................... 18
Receiving a message ............................................... 20
Transmitting a status ................................................ 22
Transmitting an SDM ............................................... 23
Position data transmission ....................................... 25
Printer connection .................................................... 25
Digital ANI ................................................................ 25
Auto emergency transmission .................................. 26
Stun function ............................................................ 26
BIIS indication .......................................................... 26
Priority A channel selection ...................................... 26
Man Down Emergency Call ..................................... 27
5 OPTIONAL SmarTrunk OPERATION .................. 28–29
SmarTrunk II™/SmarTrunk 3G™
and conventional modes ........................................... 28
SmarTrunk II™/SmarTrunk 3G™ operation.............. 28
6 OPTIONAL UNIT INSTALLATION ........................ 30–31
Optional unit installation ........................................... 30
UT-109 and UT-110 installation ................................ 31
UT-105, UT-117 and UT-117S installation ................ 32
7 BATTERY CHARGING .......................................... 33–36
Battery charging ....................................................... 33
Battery caution ......................................................... 33
Optional battery chargers ......................................... 34
8 SWIVEL BELT CLIP .............................................. 37–38
MB-93 contents ........................................................ 37
To attach .................................................................. 37
To detach ................................................................. 38
9 OPTIONS ............................................................... 39–40
10 DOC ....................................................................... 41–42
TABLE OF CONTENTS
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page iii (1,1)
1
1
ACCESSORIES
Supplied accessories
The following accessories are supplied: Qty.
q Flexible antenna ……………………………………………1
w Battery pack …………………………………………………1
e Belt clip ………………………………………………………1
r Unit cover (double-sided tape)* ……………………………1
t Jack cover (with screws) ………………………………1 set
*Use the unit cover as a spare. Ask your dealer for details.
Accessory attachments
D Flexible antenna
Connect the supplied flexible anten-
na to the antenna connector.
CAUTION!
NEVER HOLD by the antenna
when carrying the transceiver.
Transmitting without an antenna
may damage the transceiver.
qw
r
e
t
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page 1 (1,1)
2
1
ACCESSORIES
ï Battery pack
To attach the battery pack:
Slide the battery pack in the direction of the arrow (q), then
lock it with the battery release button.
• Slide the battery pack until the battery release button makes a ‘click’
sound.
To release the battery pack:
Push the battery release button in the direction of the arrow
(w) as shown below. The battery pack is then released.
NEVER release or attach the battery pack when the trans-
ceiver is wet or soiled. This may result water or dust get-
ting into the transceiver/battery pack and may result in the
transceiver being damaged.
D Belt clip
To attach the belt clip:
q Release the battery pack if it is attached.
w Slide the belt clip in the direction of the arrow until the belt
clip is locked and makes a ‘click’ sound.
To detach the belt clip:
q Release the battery pack if it is attached.
w Pinch the clip (q), and slide the belt clip in the direction of
the arrow (w).
q
w
q
w
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page 2 (1,1)
3
1
ACCESSORIES
ï Jack cover
Attach the jack cover when the optional speaker-microphone
is not used.
q
w
q
w
To attach the jack cover:
q Attach the jack cover on
the [SP]/[MIC] jack.
w Tighten the screws.
To detach the jack cover:
q Unscrew the screws with
a Phillips screwdriver.
w Detach the jack cover for
the speaker-microphone
connection.
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page 3 (1,1)
4
2
PANEL DESCRIPTION
Front panel
q ROTARY SELECTOR
Rotate to select the pre-programmed memory channels or
the operating bank.
(Depending on the pre-setting)
w VOLUME CONTROL [VOL]
Rotate to turn the power ON/OFF and adjusts the audio
level.
e DEALER-PROGRAMMABLE KEY [RED]
Desired function can be programmed by your dealer.
(p. 7)
r [SP]/[MIC] JACK
Connect the optional speaker-microphone.
t FUNCTION DISPLAY
Displays a variety of information such as an operating
channel number/name, 2/5-tone code, DTMF numbers,
selected function, etc.
y DEALER-PROGRAMMABLE KEYS [P0] to [P3]
Desired functions can be programmed independently by
your dealer. (p. 7)
[SP]/[MIC] jack cover
NOTE: Attach the [SP]/[MIC] jack
cover when the optional speaker-
microphone is not used.
(See p. 3 for details)
i
t
r
q
e
u
y
w
o
!0
!1
10-keypad version
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page 4 (1,1)
5
2
PANEL DESCRIPTION
u 10-KEYPAD (Depending on version)
The keypad allows you to enter digits to:
Select memory channels
Select tone channels
Select DTMF codes (during transmit)
Set TX codes
Set SmarTrunk II/SmarTrunk 3Gcodes
Set BIIS status number
Input text message for SDM operation
Start up with the password
i UP/DOWN KEYS
Push to select an operating channel.
Push to select a TX code channel after pushing
[TX CODE CH SELECT].
Push to select a DTMF channel after pushing [DTMF].
Push to select a scan group after pushing and holding
[SCAN].
Push to select a BIIS code, status number or SDM after
pushing [DIGITAL].
*Desired functions can be programmed independently by your
dealer. (p. 7)
o PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
Push to transmit the call during MSK operation, depend-
ing on the setting.
!0 MONITOR KEY
Mute and release the CTCSS (DTCS) or 2-tone squelch
mute. Open any squelch/deactivate any mute while
pushing this key. (LMR operation only)
Activates one of (or two of) the following functions on
each channel independently.
(PMR or BIIS PMR operation only)
Push and hold the key to unmute the channel (audio is
emitted; audible condition).
Push the key to toggle the mute and unmute conditions
(toggles audible and inaudible).
Push the key to mute the channel (sets to inaudible only).
Push the key to unmute the channel (sets to audible only).
Push the key after communication is nished to send a reset
code.
Push the key after communication is nished to send a clear
down code during BIIS operation on an MSK channel.
NOTE: The unmute condition (audible conditions)
may automatically return to the mute condition
(inaudible condition) after a specied period.
*Desired function can be programmed by your dealer. (p. 7)
!1 ANTENNA CONNECTOR
Connects the supplied antenna.
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page 5 (1,1)
6
2
PANEL DESCRIPTION
Function display
q TRANSMIT INDICATOR
Appears while transmitting.
w BUSY INDICATOR
Appears while the channel is busy.
e SCROLL INDICATOR
Appears when a received SDM including more than 8
characters is displayed.
r SIGNAL STRENGTH INDICATOR
Indicates relative signal strength level.
t LOW POWER INDICATOR
Appears when low output power is selected.
When the battery power decreases to a specified level, low
power is selected automatically.
y AUDIBLE INDICATOR
Appears when the channel is in the audible (unmute)
condition.
Appears when the specified 2/5-tone/BIIS code is
received.
u COMPANDER INDICATOR
Appears when the compander function is activated.
i SCRAMBLER INDICATOR
Appears when the voice scrambler function is activated.
o BELL INDICATOR
Appears/blinks when the specific 2/5-tone/BIIS code is
received, according to the pre-programming.
!0 CALL CODE MEMORY INDICATOR
Appears when the call code memory is selected.
!1 KEY LOCK INDICATOR
Appears during the key lock function is ON.
!2 BATTERY INDICATOR
Appears or blinks when the battery power decreases to a
specied level.
!3 ALPHANUMERIC DISPLAY
Displays an operating channel number, channel name, Set
mode contents, DTMF code, etc.
q !1!0oiuytrew
!2
!3
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page 6 (1,1)
33
7
BATTERY CHARGING
Battery charging
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation.
CAUTION: To avoid damage to the transceiver, turn the
power OFF while charging.
Recommended temperature range for charging:
+10°C to +40°C
Use the specified chargers (BC-119N, BC-121N and BC-
160). NEVER use another manufactures charger.
Use the specied AC adapter. NEVER use another manu-
factures adapter.
Battery caution
R DANGER Charge the specied Icom batteries only.
Only tested and approved for use with genuine Icom batter-
ies. Fire and/or explosion may occur when a third party bat-
tery pack or counterfeit product is charged.
CAUTION! NEVER insert battery pack/transceiver (with the
battery pack attached) in a wet or soiled condition into the
charger. This may result in corrosion of the charger terminals
or damage to the charger. The charger is not waterproof and
water can easily get into it.
NEVER incinerate used battery packs. Internal battery gas
may cause an explosion.
NEVER immerse the battery pack in water. If the battery
pack becomes wet, be sure to wipe it dry BEFORE attaching
it to the transceiver.
NEVER short the terminals of the battery pack. Also, current
may ow into nearby metal objects, such as a necklace, etc.
Therefore, be careful when carrying with, or placing near
metal objects, carrying in handbags, etc.
AVOID leaving the battery pack in a fully charged, or completely
discharged condition for long time. It causes shorter battery life.
In case of leaving the battery pack unused for a long time, it
must be kept safely after discharge, or use the battery until the
battery indicator appears, then remove it from the transceiver.
If your battery pack seems to have no capacity even after
being charged, fully charge the battery pack again. If the bat-
teries still do not retain a charge (or very little), new battery
pack must be purchased.
Recommendation:
Charge the supplied battery pack for a maximum of
up to 10 hours. Li-Ion batteries are different from Ni-
Cd batteries in that it is not necessary to completely
charge and discharge them to prolong the battery life.
Therefore, charging the battery in intervals, and not
for extended periods is recommended.
IC-F34_44GT_GS-1.qxd 04.9.24 10:26 AM Page 33 (1,1)
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Icom IC-F34GT GS F44GT GS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Icom IC-F34GT GS F44GT GS in de taal/talen: Engels als bijlage per email.

De handleiding is 1,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info