12346
104
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
13
91
MAINTENANCE
2001 NEW
SCAN
Troubleshooting
The following chart is designed to help you correct
problems which are not equipment malfunctions.
If you are unable to locate the cause of a problem or
solve it through the use of this chart, contact your near-
est Icom Dealer or Service Center.
PROBLEM POSSIBLE CAUSE SOLUTION REF.
RECEIVE
POWER
TRANSMIT
Power does not come on
when the [POWER] switch
is pushed.
No sounds come out from
the speaker.
Sensitivity is too low, and
only strong signals are au-
dible.
Received audio is unclear
or distorted.
The [ANT] switch does not
function
Transmitting is impossible.
Output power is too low.
No contact possible with
another station.
Transmit signal is unclear
or distorted.
Repeater cannot be ac-
cessed.
Programmed scan does
not stop.
Programmed scan does
not start.
Memory scan does not
start
Select memory scan does
not start
Power cable is improperly connected.
Fuse is blown.
Volume level is too low.
The squelch is closed.
The transceiver is in transmitting condition.
The antenna is not connected properly.
The antenna for another band is selected.
The antenna is not properly tuned.
The attenuator is activated.
Wrong operating mode is selected.
PBT function is activated.
Noise blanker is turned ON when receiving a
strong signal.
Preamp is activated.
The noise reduction is activated and the [NR]
control is too far clockwise.
The antenna switch has not been activated.
The operating frequency is not set to a ham
band.
[RF PWR] is set too far counterclockwise
[MIC GAIN] is set too far counterclockwise
The antenna for another band is selected.
The antenna is not properly tuned.
RIT or TX function is activated.
Split frequency and/or duplex function are acti-
vated.
[MIC GAIN] is set too far clockwise
Split frequency or duplex function is not acti-
vated.
Programmed subaudible tone frequency is
wrong.
Squelch is open.
[RF/SQL] is assigned to RF gain control and
squelch is open.
The same frequencies have been programmed
in scan edge memory channels P1 and P2.
2 or more memory channels have not been
programmed.
2 or more memory channels have not been
designated as select channels.
Re-connect the DC power cable correctly.
Check for the cause, then replace the fuse with
the spare one.
(Fuses are installed in the DC power cable and
the internal PA unit.)
Rotate [AF] clockwise to obtain a suitable lis-
tening level.
Turn [RF/SQL] to 10 oclock position to open the
squelch.
Push [TRANSMIT] to receive or check the
SEND line of an external unit, if desired.
Re-connect to the antenna connector.
Select an antenna suitable for the operating fre-
quency.
Push [TUNER] for 1 sec. to manually tune the
antenna.
Push [P.AMP/ATT] for 1 sec. to select ATT OFF.
Select a suitable operating mode.
Push [PBTC] for 1 sec. to reset the function
Push [NB] to turn the noise blanker OFF.
Push [P.AMP/ATT] once or twice to turn the
function OFF.
Set the [NR] control for maximum readability.
Set the antenna switch in set mode to Auto or
Manual.
Set the frequency to a ham band.
Rotate [RF PWR] clockwise.
Set [MIC GAIN] to a suitable position.
Select an antenna suitable for the operating fre-
quency.
Push [TUNER] for 1 sec. to manually tune the
antenna.
Push [RIT] or [TX] to turn the function OFF.
Push [SPLIT] and/or [F2 DUP] (in M1) to turn
the function OFF.
Set [MIC GAIN] to a suitable position.
Push [SPLIT] and/or [F2 DUP] (in M1) to turn
the function ON
Reset the frequency using set mode.
Set [RF/SQL] to the threshold point.
Reset [RF/SQL] control assignment and set it to
the threshold point.
Program different frequencies in scan edge
memory channel P1 and P2.
Program more than 2 memory channels.
Designate more than 2 memory channels as se-
lect channels for the scan.
p. 16
p. 92
p. 23
p. 24
p. 25
p. 74
pgs. 75,
76
p. 47
p. 23
p. 51
p. 50
p. 47
p. 52
p. 84
p. 19
p. 25
p. 25
p. 74
pgs. 75,
76
pgs. 47,
56
pgs. 44,
58
p. 25
pgs. 44,
58
p. 45
p. 24
pgs. 24,
81
p. 65
p. 62
p. 71
IC-7400.qxd 02.4.2 11:36 Page 91
104

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Icom-IC-7400

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Icom IC-7400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Icom IC-7400 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info