12346
73
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
60
6
FUNCTIONS FOR TRANSMIT
2001 NEW
Measuring SWR
The IC-7400 has a built-in circuit for measuring an-
tenna SWR no external equipment or special adjust-
ments are necessary.
The IC-7400 can measure SWR in 2 ways spot
measurement and plot measurement are available.
DD
Spot measurement
q Push [TUNER] to turn the antenna tuner OFF.
w Turn the COMP meter OFF.
Push [MENU] for 1 sec. to enter set mode.
Push [F1 ] or [F2 ] several times to select the
COMP Meter item.
Rotate the tuning dial to set the COMP meter OFF.
Push [MENU] to exit set mode.
e Push [CW/RTTY] several times to select RTTY
mode.
r Push [TRANSMIT] or [PTT] on the microphone.
t Rotate [RF PWR] clockwise past the 12 oclock po-
sition for more than 30 W output power (30%).
y Read the SWR on the SWR meter.
u Push [TRANSMIT] or release [PTT] to receive.
The built-in antenna tuner matches the transmitter
to the antenna when the SWR is lower than 3:1.
DD
Plot measurement
Plot measurement allows you to measure the SWR
over an entire band.
q While M2 is selected with [MENU], push [F3 SWR].
SWR graph screen appears.
w Rotate [RF PWR] clockwise past the 12 oclock po-
sition for more than 30 W output power (30%).
e Set the center frequency for the SWR to be mea-
sured.
r Push [F5] for 1 sec. several times to select the de-
sired measuring step from 10, 50, 100 and 500 kHz.
t Push [F3] several times to select the desired num-
ber of measuring steps from 3, 5, 7, 9, 11 and 13
steps.
y Push [F1] to start the measuring.
u Push [TRANSMIT] or push and hold [PTT] on the
microphone to measure the SWR.
Frequency marker, , appears below SWR graph.
RTTY mode is automatically selected.
i When pushing [TRANSMIT] again or releasing
[PTT], the frequency marker and frequency indica-
tion move to the next frequency to be measured.
o Repeat steps u and i to measure SWR over the
entire frequency range.
!0 When the measured SWR is less than 1.5:1, the
antenna is well matched with the transceiver in the
measured frequency range.
AGC
DUP
1/4
RTY
SCP
The best match is in this range.
F 1
F
2F
3
F
4
F
5
F 1
F 2 F 3 F 4 F 5
SCN
MEM
SWR
TCN
VSC
1Ok
STEP
1Ok
STEP
Push [F3]
Push [F5] to select
SWR measuring step.
Push [F3] to select number of SWR measuring steps.
Push [F1] to start
measuring.
Measuring (after pushing [F1])
Frequency marker appears and moves after meas-
urement.
*When mesurement point/s is/are set outside of the oper-
atable frequency band, the frequency marker flashes.
Typical display SWR varying between 1 and 2,
full scale up to SWR 4.0:1.
1.0:1
1.5:1
2.0:1
3.0:1
4.0:1
IC-7400.qxd 02.4.2 11:35 Page 60
73

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Icom-IC-7400

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Icom IC-7400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Icom IC-7400 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info