695125
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Protecting the iBT370
The iBT370 comes equipped with a Weather Tough rubberized cover that
protects the buttons and ports. Make sure the rubber cover is sealed shut
before operating near water or dust.
The iBT370 is powered by a rechargeable battery in the speaker. Make sure to
charge speaker before use.
Connect the micro-USB plug on the included charging cable to the USB
Charging jack on the speaker.
Connect the larger USB plug to a powered USB port, such as that on a
computer. Your computer should be connected to a wall outlet when speaker
is charging. The light on the speaker will turn to solid red while charging and
turn off when fully charged.
If the LED flashes red, or you notice sound distortion at higher volumes, or
there is no sound at all, it's time to recharge the battery.
Using Bluetooth with the iBT370
Place your audio device in Bluetooth mode (often found in the device’s
Settings or Tools menu) and make it “discoverable”.
Press and hold the Power ON/OFF Button for 5 seconds to turn on the
iBT370 speaker. The first time unit is powered on it will enter auto-pairing
mode.
• “iHome iBT370” should appear on your device’s Bluetooth menu. Select it to
connect. If your device asks for a passcode, enter ‘1234’.
Once paired, the light will glow solid blue and a confirmation tone will sound.
You can then stream audio to the speaker. If pairing is not successful, turn the
power off on the speaker and repeat pairing procedure.
To pair a different device or pair at another time, power ON the iBT370,
then press and hold the Bluetooth/Play/Pause/Speakerphone Button for 2
seconds.The LEDs will flash blue and red, a tone will sound as the speaker
attempts to pair with a Bluetooth device.
To listen to Bluetooth audio, press the Bluetooth/Play/Pause/Speaker-
phone Button on the speaker to cycle between play and pause modes.
• Control audio volume and track navigation from your device. Remember to
turn off the speaker (press and hold the Power ON/OFF Button for 5
seconds) after listening.
NOTE: When unit is charging, the blue light will appear solid red.
Using the iBT370 Speakerphone Mode
The speaker must be on and connected to a paired Bluetooth phone to receive
calls. When a call comes in, any playing audio is paused, the LED will flash
blue 2X and the ringtone associated with the caller may sound, depending on
Bluetooth device.
Press the Bluetooth/Play/Pause/Speakerphone Button to answer the call.
Press again to end the call.
FCC ID: EMOIBT370
IC: 986B-IBT370
Model: iBT72Y (Front) Speaker phone
IB (English) Taide
Size: 324Wmm x 200Hmm
Color: Print in Black color
Date: Nov 16, 2015
Questions? Visit www.ihome.com
Water Resistant
Bluetooth
Speaker
CHARGE
BEFORE
USE
Charging the iBT370
CHARGE BEFORE USE
Computer USB port
USB charging jack
USB charging jack
USB AC adapter
(not included)
USB AC adapter
connected to working outlet
Computer
connected to
working outlet
Model: iBT72Y (Speaker phone)
IB (English) Taide
Size: 324Wmm x 184Hmm
Color: Black color
Date: Nov 16, 2015
90gsm2 WF paper
USB Charging Jack
Bluetooth Pairing
Press and hold
5 seconds to
turn Speaker
ON or OFF
Press and hold
2 seconds to
begin pairing
Press to play/pause
audio
Select
“iHome iBT370”
to connect
iHome
Speakerphone Mode
charging cable included
FCC Information
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B)/NMB-3(B)
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS
102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne
sur l'exposition et la conformité de rf.
DID: D025616
IMPORTANT
Read before proceeding
If you have any question regarding the operation or use of this product, please visit
www.ihome.com to view answers to frequently asked questions.
To learn more about this and other iHome products, please visit us online at www.ihome.com
Charging cable
Many electronics retailers now recycle batteries and other electronic components at
no charge. Check to see which ones in your area do so.
CAUTION
The battery used in this device may present a risk of fire, explosion or chemical burn if mistreated
Never use or charge the battery if it appears to be leaking, discolored, deformed, or
in any way abnormal.
Never disassemble the unit or attempt to remove battery as that could cause leakage
of alkaline solution or other electrolytic substance.
Always confirm that the temperature is 5°C – 35° C (41° - 95° Fahrenheit) before you
charge the battery. Leakage or deterioration of the battery may occur if this warning
is not heeded.
Never expose the battery to any liquid.
Never expose the battery to excessive heat such as direct sunlight or fire. Never use
the battery pack in an unventilated vehicle where excessive internal temperatures
may be encountered.
Always keep the battery out of the reach of infants and small children.
Maintenance
Place the unit on a level surface away from sources of direct sunlight or excessive
heat.
Protect your furniture when placing your unit on a natural wood and lacquered finish.
A cloth or other protective material should be placed between it and the furniture.
Clean your unit with a soft cloth moistened only with mild soap and water. Stronger
cleaning agents such as thinner or similar materials can damage the surface of the
unit.
Limited 1 Year Warranty Information
i
Home Products, a division of SDI Technologies Inc. (hereafter referred to as SDI), warrants this product
to be free from defects in workmanship and materials, under normal use and conditions, for a period of
one (1) year from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where
it was originally purchased. Should this fail to resolve the matter and service still be required by reason
of any defect or malfunction during the warranty period, SDI will repair or, at its discretion, replace this
product without charge. This decision is subject to verification of the defect or malfunction upon delivery
of this product to the Factory Service Center authorized by Customer Service.
If service is required, please call Customer Service at 1-800-288-2792 to obtain a Return Authorization
Number and shipping instructions. A copy of the sales receipt is required to validate in-warranty
coverage.
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does
not cover (i) products which have been damaged by negligence or willful actions, misuse or accident, or
which have been modified or repaired by unauthorized persons; (ii) cracked or broken cabinets, or units
damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes (if applicable);
(iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product
other than to the original purchaser. In no event will SDI or any of its affiliates, contractors, resellers, their
officers, directors, shareholders, members or agents be liable to you or any third party for any consequential
or incidental damages, any lost profits, actual, exemplary or punitive damages. (Some states do not allow
limitations on implied warranties or exclusion of consequential damages, so these restrictions may not
apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer
of warranty is contractually binding to you upon your transfer of currency (money order, cashier's check,
or credit card) for purchase of your SDI product.
© 2017 SDI Technologies, Inc. All rights reserved
Questions? Visit www.ihome.com
or call 1-800-288-2792 Toll Free
iBT85-152217-A Printed in China
A Consumer Guide to Product Safety
IMPORTANT SAFETY INSTRUCTIONS
When used in the directed manner, this unit has been designed and manufactured to ensure your personal
safety. However, improper use can result in potential electrical shock or fire hazards. Please read all
safety and operating instructions carefully before installation and use, and keep these instructions handy
for future reference. Take special note of all warnings listed in these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub,
washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its
proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that
may block ventilation openings. Also, it should not be placed in a built-in installation, such as a
bookcase or cabinet, which may impede the flow of air through the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves
or other appliances (including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in
the operating instructions or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them. It is always best to have a clear
area from where the cable exits the unit to where it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of
this manual for cleaning instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not
spilled into any openings or vents located on the
product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect
the antenna or cable system during a lightning storm or when it is left unattended and unused for
long periods of time. This will prevent damage to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles
as this can result in a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A. the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E. the unit exhibits a marked change in performance or does not operate normally.
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a
month or longer, the power cable should be unplugged from the unit to prevent damage or corrosion.
13. Servicing – The user should not attempt to service the unit beyond those methods described in
the user’s operating instructions. Service methods not covered in the operating instructions should
be referred to qualified service personnel.
Lithium-ion Battery
Internal Rechargeable Lithium-ion Battery
This device uses an internal rechargeable lithium-ion battery that should last the lifetime
of the device. If you suspect your battery may be dead, try charging it several times. If
the battery does not recharge, please contact Customer Service at 1-800-288-2792
WARNING/DISPOSAL OF UNIT
Please do NOT attempt to change the battery yourself. Doing so cn damage your device
and will void your warranty.
Never dispose of used batteries/electronics with ordinary solid wastes, since they
contain toxic substances.
Always dispose of used batteries/electronics in accordance with the prevailing
community regulations that apply to the disposal of batteries/electronics. If there are
no local regulations concerning battery/electronics disposal, please dispose of the
device in a waste bin for electronic devices.
Press to answer and end calls
2 Sec5 Sec
Model: iBT370
Power ON/OFF
Button
Bluetooth/Play/Pause/
Speakerphone Button
Bluetooth
Pairing LED
Battery
LED
Speaker top view
with cover open
Pinhole Reset
Charging the iBT370
How to Reset the iBT370
To reset the iBT370, use the tip of a paper clip or
other thin tool to press in the Pinhole Reset.
iHome
iBT370
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw IHome iBT370 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van IHome iBT370 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info