675897
7
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
W
arning against flying objects wear helmet,
goggles and ear protection.
W
arning: Danger from hot components,
especially exhaust - Keep clear of combustible
materials.
1.
10. Additional safety instructions.
1.10.1. This machine may only be used for
trimming grass, weeds and brushwood. Never
use for other purposes, as this may result in
serious injury! Safety instructions must be
observed. DO NOT EXPOSE YOURSELF OR
OTHERS TO THE RISKS. Follow these general
instructions -
ALWAYS wear safety goggles for eye
p
rotection.
Long hair must be tied back.
DO NOT wear loose clothing or jewelry tha
t
c
ould get caught in moving parts of the
machine. Safe, strong, non-slip safety shoes
should be worn.
It is recommended that the legs and feet
are fully protected, to protect themselves
during the operation against flying objects.
1
.10.2. Check the entire machine for
loose/missing parts (nuts, bolts, screws, etc.).
Tighten/ replace before using the machine. DO
NOT use accessories with this machine other
than those recommended/supplied by the
manufacturer. Otherwise serious injuries to
the user or bystanders as well as damage to
the machine will result.
Keep the handles free of oil and fuel.
ALWAYS use the correct interface handles
and shoulder strap.
DO NOT smoke when mixing fuel or when
filling the tank.
DO NOT mix fuel in an enclosed area or
near open fires.
Make sure sufficient ventilation
/
ventilation.
Mix and store the fuel mixture in a
correctly marked container, which is
allowed by local regulations.
1.10.3. During and after use the engine and
exhaust will be very HOT you must keep all your
all parts of your body and clothing including all
combustible materials clear of the engine and
exhaust.
1.10.4. DO NOT use the machine during or
after rain, snow or sleet. The floor will become
slippery. DO NOT use the machine on a slope
or uneven ground or if there is the chance of
slipping or losing the stability.
1.10.5. If you trip or fall whilst machine is in
use you MUST immediately release the
throttle, and turn off the ignition switch.
1.10.6. If you hit any obstacles you must stop
the machine and remove the HT lead so that
you can inspect the machine. IF the machine is
damaged in any way you MUST get it repaired
before restarting work.
1.10.7. DO NOT use a damaged machine or a
machine with a blunt, cracked or damaged
cutter blade or trimmer head.
1.10.8. When using the blade cutter there is a
danger of kickback. Kickback is a reaction that
can occur when the rotating cutting blade
strikes an object which cannot be cut. This
contact causes the cutting blade to stop for an
instant and then suddenly repel from the
object taken with accelerated force. This
reaction can be violent enough that the
operator momentary loses control of the
machine. A kickback can occur without
warning when the cutter encounters an
unseen obstacle when the blade is running.
This is more likely in areas where it is difficult
to properly check the material/area to be cut.
For easy and safe cutting, cut the weeds/brush
from right to your left.
1.10.9. If any trimmed materials get tangled in
the nylon cord or cutting blade you MUST stop
the machine and remove the HT lead. Onley
then can you clear any blockages.
Page 7
Rev 3 - September 2016
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hyundai 57132 - HYBC5200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hyundai 57132 - HYBC5200 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info