813010
17
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
17.01.2019 / 53-1102
www.hwam.com
User Manual
HWAM® SmartControl Generation 2
Wi-Fi Frequency: 2.4 GHz.
EN
2
Installation instructions 3
Introduction to HWAM® SmartControlTM 3
Before using HWAM® SmartControlTM 3
First setup 4
Connecting to Wi-Fi networks 6
Operating instructions IHS SmartControlTM app* 7
Startup - app 7
Home screen / front 7
Night reduction 8
Phase indication 8
Stoking time 10
Flue gas temperature, room temperature, temperature level 10
Home Screen - Live data 11
IHS SmartControlTM - messages 12
IHS SmartControlTM - menu 13
Alarms & Warnings 16
Room temperature sensor 17
Pairing of the room temperature sensor with HWAM® SmartControl™ 18
Changing the batteries of the room temperature sensor 19
Firing process 20
Specifications for HWAM® SmartControlTM generation  23
*The app for HWAM® SmartControlTM is called IHS SmartControlTM (IHS = Intelligent Heat System).
CONTENTS
3
App Store: Google Play Store:
The following sections will provide an introduction to the HWAM® SmartControl™ app named
IHS SmartControl™ and the associated wireless room temperature sensor, and how they
operate.
HWAM® SmartControl™ provides a number of advantages:
• It’s the most environmentally friendly way to heat the stove
• Saves up to  percent of the cost of the firewood
• Provides an even temperature in the room
• Makes it easy to fire
• Optional night-time lowering where the fire attenuates and the heat emanates
from the embers in an environmental way
• Signals when new wood is required
INSTALLATION INSTRUCTIONS
Before using the stove, it is important that the following steps are taken:
1
Make sure there is no power connected to HWAM® SmartStove™.
2 Put  of the  AA batteries in the room temperature sensor. Press the button on the front
of the room temperature sensor while the third battery is being placed inside, and hold
until the LED flashes green signalling that it is ready to be paired with the stove. See also
the section on the pairing of the room temperature sensor with HWAM® SmartControlTM on
page . Do not use rechargeable batteries.
3 Plug in the HWAM® SmartStove™ immediately using the power supply.
4 Allow the system to boot up for the first time, this takes about  minute. The green diode
on the room temperature sensor will briefly turn solid green and then turn o when the
room temperature sensor has automatically been successfully paired with the stove.
5 The HWAM® SmartControl™ can be used with a smartphone or tablet that uses the operat-
ing system iOS or Android. To download the app search for IHS Smart Control™ In the App
Store or Google Play Store or scan the QR code below.
Introduction to HWAM® SmartControlTM
Before using HWAM® SmartControlTM
4
Wi-Fi Direct
Wi-Fi network
Setup
You can set up HWAM® SmartControl™ via the IHS
SmartControl™ app and you can only do this using an
iPhone, iPad or Android device.
PCs or MACs cannot be used to setup the system.
Information about the Wi-Fi connection
HWAM® SmartControl™ can be configured to commu-
nicate directly with mobile devices or through a Wi-Fi
network.
It is best to connect a Wi-Fi network as this is the most
advantageous and the most user-friendly use of the
system.
HWAM® SmartControl™ supports  stoves on the same
network.
1-2 units
up to 5 units
Introduction
The following sections describe how the HWAM® SmartControl™ is connected to a Wi-Fi net-
work or via Wi-Fi Direct.
It is always best to connect the system to a Wi-Fi network, as this ensures the best connec-
tion to the system and the simplest operation. It is not necessary to connect to the Internet in
order to use HWAM® SmartControl™ or HWAM® SmartStove™ on a wireless network.
First Setup
5
2
3
1
1
2
2
1
Connection icons
1
No connection (red Wi-Fi icon)
2 Wi-Wi-Fi Direct connection (green Wi-Fi icon)
3 Connected through the network (green Wi-Fi icon
with a tick)
HWAM® SmartControl™ can be used by directly connec-
ting the device and HWAM® SmartControl™, also called
Wi-Fi Direct, displayed by a green symbol. HWAM®
SmartControl™ can also be configured to connect
through a Wi-Fi network, which is recommended. This
connection is indicated by a green symbol with a tick.
Setting up a Wi-Fi connection
The following sections describe how HWAM® Smart-
Control™ is connected to a Wi-Fi network for the first
time. To set up HWAM® SmartControl™, it is necessary to
connect via Wi-Fi Direct first, and then connect HWAM®
SmartControl™ to a Wi-Fi network.
Connecting to Wi-Fi Direct on iPhone
Go to "Settings" on your phone and then select "Wi-Fi" 1.
Make sure that the device has Wi-Fi turned on and
that power is connected to HWAM® SmartControl™ (the
stove). There will now be a Wi-Fi device available called
"IHS STOVE_XXXXX" 2. Connect to this. If you do not
wish to connect HWAM® SmartControl™ to a network,
the system is now ready for use.
Connecting to Wi-Fi Direct on Android
Go to “Settings” on your phone and then select “Wi-Fi” 1.
Make sure that the device has Wi-Fi turned on and
that power is connected to HWAM® SmartControl™ (the
stove). There will now be a Wi-Fi device available called
"IHS STOVE_XXXXX" 2. Connect to this. If you do not
wish to connect HWAM® SmartControl™ to a network,
the system is now ready for use.
NOTE: The number after "STOVE" is unique to each
individual stove.
6
3
1
2
1
2
3
1
Connecting to Wi-Fi networks
After the mobile device is connected via Wi-Fi Direct,
HWAM® SmartControl™ can be connected to a Wi-Fi
network. To connect a Wi-Fi network, press the green
connection icon 1.
If you wish to connect HWAM® SmartControl™ to the
network, click "Yes" 2. This is recommended.
Enter the name of the stove for example: "Living room"
or "First floor." 3
NOTE: The name is used primarily when there are
multiple stoves connected to the same network.
HWAM® SmartControl™ will now search for all available
networks.
Make sure that your network is turned on and accessi-
ble and that your SSID is visible (Service Set Identifier).
NOTE: If there are many available networks, this
can take a while.
Select the network that HWAM® SmartControl™ shall be
connected to 1.
Enter the password for the selected network 2, and
press "Connect to network" 3.
HWAM® SmartControl™ will now try to connect to the
selected network using the code entered.
HWAM® SmartControl™ is now connected to the selec-
ted network. It is no longer possible to access HWAM®
SmartControl™ via Wi-Fi Direct. HWAM® SmartControl™
can only be operated by connecting the mobile device
to the same network as the HWAM® SmartControl™.
If HWAM® SmartControl™ cannot connect to the net-
work, the Wi-Fi Direct connection will automatically
become available again.
NOTE: For servicing the Wi-Fi Direct connection
will be available for one minute after the system has
been restarted.
7
1
2
1
2
3
4
5
7
6
1
8
9
8
3
1
2
The following section comprises the home screen / front page of IHS SmartControl™ app
which describes which features are available and how they are operated.
To use all functions, it is necessary to ensure that the IHS SmartControl™ is connected to
HWAM® SmartControl™ (a stove with HWAM® SmartControl). However, many features are
available without connecting to the system.
The IHS SmartControl™ menu contains a series of menus, all of which will be discussed in the
following sections.
1 App menu
The menu can be found in the top left corner.
2 Connection icon
The connection icon shows when there is a connection
between the HWAM® SmartControl and the stove.
The red icon indicates no connection
The green icon indicates a connection via Wi-Fi Direct
The green icon with a tick signals that the stove has
been connected to the user’s own Wi-Fi network
(home network).
IHS SmartControl™ Main Screen / Front:When the IHS SmartControl™ app is
started, the IHS logo is displayed:
App Menu
Status Icon (Connection)
Stove Name
Night Reduction
Phase Indication
Restoking Timer
Flue Gas Temperature
Room Temperature
Temperature Level
Startup - app
Home screen / Front page
OPERATING INSTRUCTIONS
IHS SMARTCONTROLAPP
8
3
A B
A B
A
3 Stove name
The stove name displays the name of the stove con-
nected to the IHS SmartControl™ app. This is used in the
case where several stoves are connected to the same
network. If the stove has not previously been con-
nected to a network, it will have no name and nothing
will be displayed.
4 Night reduction
A Active (green) B Inactiv (black)
To activate / deactivate the night reduction press the
icon. Night reduction automatically lowers the tempera-
ture setting of the stove, which ensures a longer com-
bustion time with reduced room temperature.
NOTE: Night reduction is only active in the chosen
time period (see the section “Night reduction – time
management”)
.
Night reduction – time management
A Start Time B Stop time
To set the start or stop time for night reduction, press
the icon and hold for  seconds. Press the time and
select the desired time in the dialogue box. At the start
time selected, HWAM® SmartControl™ automatically
goes into night reduction mode to achieve the longest
possible burning. At the same time, the room tempe-
rature function in the HWAM® SmartControl™ is deacti-
vated. At the stop time selected, HWAM® SmartControl™
will automatically return to normal operation and the
previously set temperature level.
NOTE: If the temperature level is changed while the
system is in night reduction mode, night reduction
will be automatically disabled.
5 Phase indication
The phase indicator shows the current combustion
phase of the HWAM® SmartControl™. There are a total
of five phases:
A Start
9
D
C
B
B Lighting up
The phase indicator shows that the system is in
the lighting up phase. The symbol is displayed
after the door has been opened on a cold stove,
or in the case where the standby / start icon of the
IHS SmartControl™ app has been pressed. If the
flue gas temperature does not increase within 
minutes, the HWAM® SmartControl™ will automat-
ically shut o the air supply and return to standby
mode. See the section on correct firing process on
page .
NOTE: To ensure complete combustion e-
ciency it is important to obtain a suciently
high flue gas temperature. Failing this, HWAM®
SmartControl™ emits a restoking alarm, even if
there is unburned wood and flames.
C Combustion
The phase indicator shows that the system is in
the combustion phase and has exited the light-
ing up stage. The system automatically regulates
combustion, ensuring optimum combustion and a
room temperature as close to the desired level as
possible.
D Ember phase
The phase indicator shows that the system is in
ember phase. In this phase there will be mainly
only embers in the stove, and the system will now
also be able to calculate the expected time for the
next restoking (described in a following section).
The system automatically gives an alert regarding
the correct restocking time. It is recommended that
you wait before restoking until the restoke alarm is
emitted, as the expected firewood saving is oth-
erwise not achievable. If there is a big dierence
between actual and desired room temperature,
the restoking alarm comes on, even though there
is unburned wood and flames. Failure to restoke at
this time, will lead to a new restoking alarm being
emitted, which constitutes the last opportunity to
restoke without new lighting up.
NOTE: The best and most economical combus-
tion is achieved by following the recommended
stoking time carefully.
10
E
6
8
9
7
E Standby
The phase indicator shows that the system is in
standby mode. This means that the system has
been in use, and that the temperature in the
stove is now so low that it cannot be guaranteed
that the stove can light new wood. It is therefore
necessary start anew if you want to burn more
wood.
6 Stoking time
The stoking time shows the estimated time to the next
stoking. The stoking time will only be estimated when
the system reaches the ember phase. If there is a big
dierence between actual and desired room tempera-
ture, the restoking alarm comes on, even though there
is unburned wood and flames.
Flue gas temperature
Displays the measured flue gas temperature. The ther-
mal sensor is located at the smoke outlet of the stove.
Room temperature
Displays the temperature measured by the accompa-
nying room temperature sensor. The temperature may
vary by +/-oC in relation to the temperature measured
by another thermometer.
9 Temperature level
The temperature level-setting runs from "Level "
through "Level ". The level can be changed by press-
ing "+" or "-" which regulates the desired temperature
level up or down. The individual levels are explained in
detail in the following sections.
NOTE: Night reduction automatically puts the system
at "Level ". If, however, the level is subsequently
changed, night reduction is disabled.
REMEMBER:
Never leave a stove after igniting a
fire before ensuring that there are
long lasting flames!
7
8
17
2
1
1 LED indicator
There is an LED indicator at the bottom of the wireless
room temperature sensor. This will indicate the following:
A No connection to HWAM® SmartControl™
In the absence of a connection to the HWAM®
SmartControl™, the room temperature sensor will
alternately flash green and red.
B Pairing mode
When the room temperature sensor is ready to
be paired with the HWAM® SmartStove™, it will
flash green at a fast pace.
C Restoking
When HWAM® SmartControl™ detects that it is
time to refill with additional wood, the room tem-
perature sensor makes repetitive sounds while
flashing green at a steady pace.
D Alarms & Warnings
When HWAM® SmartControl™ detects an alarm
or warning, the room temperature sensor makes
repetitive sounds and simultaneously flashes
red.
For further information and details about the
alarm or warning in question, use the IHS Smart-
Control™ app.
A room temperature sensor is provided as a standard with the HWAM® SmartControl™. This
is used by the system to detect the room temperature and adjust the combustion in order to
ensure an even and comfortable room temperature.
The sensor communicates with HWAM® SmartControl™ via a wireless connection. The maxi-
mum distance in clear view between the HWAM® SmartStove™ and the room temperature
sensor is  - metres. The range is shorter if there are walls in between.
The room temperature sensor is provided with a light indicator 1 at the bottom of the unit, a
button on the front of the unit 2, and an in-built speaker.
NOTE: It is not possible to adjust the volume on the device.
Room temperature sensor
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hwam SmartControl Generation 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hwam SmartControl Generation 2 in de taal/talen: Engels als bijlage per email.

De handleiding is 4.95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Hwam SmartControl Generation 2

Hwam SmartControl Generation 2 Gebruiksaanwijzing - Nederlands - 24 pagina's

Hwam SmartControl Generation 2 Gebruiksaanwijzing - Deutsch - 24 pagina's

Hwam SmartControl Generation 2 Gebruiksaanwijzing - Français - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info