627057
10
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
10
6.2 maschIne bewegen
Zum Bewegen der Maschine einen Gabelstapler verwenden.
Die Maschine nach folgendem Verfahren und folgenden Vorsichtsmaßnahmen mit einem Gabelstapler wie
abgebildet bewegen.
Die Verpackungskiste mit einem geeigneten Gabelstapler bewegen.
Die beiden Zinken des Gabelstaplers wie abgebildet unter der Verpackungskiste
positionieren.
Den Abstand der Staplerzinken zum Schwerpunkt verstellen, bis L1 = L2 (L1 & L2 =
jeweils 450 mm)
Die Staplerzinken vollständig unter die Verpackungskiste schieben.
Maschine mit Ketten bzw. Stahlseilen an den Staplerzinken und am Gabelstapler
befestigen.
Die Staplerzinken müssen vollständig untergeschoben sein.
L1 muss gleich L2 entsprechen, damit die Maschine sich im Gleichgewicht befindet.
6.3 InstallatIon der maschIne
Maschine mit Befestigungsbolzen auf dem Boden der Verpackungskiste befestigen.
(1) Werkzeuge
Hebeseil, Hebeeinrichtungen, Schraubenschlüssel, Verschiebeplatte, Einlegeblöcke und Ausrichtblöcke.
(2) Verfahren
Nach der Demontage der Verpackungskiste die Handbücher und den Werkzeugkasten entnehmen.
Befestigungsbolzen entfernen.
Kiste an ein Hebeseil befestigen, anheben und aus dem Weg räumen.
Bodenbefestigungsbolzen und Maschinenfußbohrungen zueinander ausrichten. In der Zwischenzeit die
Ausrichtblöcke unter den Ausrichtschrauben ablegen.
Hebeausrüstung und Hebeseil entfernen.
Muttern der Bodenbefestigungsbolzen aufsetzen.
6.4 maschInennIveau eInstellen
(1) Werkzeuge
Präzisionswasserwaage mit einer Toleranz von 0,02 mm/m
Schraubenschlüssel, Ausrichtblöcke
(2) Verfahren
Ausrichtblöcke so einstellen, dass diese Kontakt zu den Ausrichtschrauben besitzen.
Präzisionswasserwaage auf dem Arbeitstisch ablegen.
Mit der Präzisionswasserwaage den höchsten Punkt ermitteln und als Referenzniveau verwenden.
Über die Präzisionswasserwaage mit den Ausrichtschrauben das Maschinenniveau einstellen.
1 = Ausrichtschrauben
4-2
4.2 Transportation
4.2.1 The diagram of the machine weight and its gravity center
The weight differ due to the different models. Their data is as blow:
MODEL TPR-1230 TPR-1230H TPR-1600H TPR-2000H
Total Weight 2300 kgw 2300kgw 5100kgw 6600kgw
Required Forklift 2.5 tons 2.5 tons 5 tons 7 tons
Note:
Please make sure that the forklift tonnage is suitable for the machine.
The above arrow pointed place is the machine’s
g
ravit
y
center. It is about 200 mm far from
the Column, measured from the middle of the wooden crate.
4.2.2 The movement of the machine.
There are using forklift to move the machine.
The following is the procedure, precaution and illustration for moving the machine with
forklift.
a. Have a suitable forklift move to the wooden crate.
b. As diagram shown, insert two forks into the underneath of the
wooden crate.
c. Adjust the distance from the forks to the gravity center till L1
is equal to L2. (L1 & L2=450mm)
d. Have forks fully inserted into the underneath of the wooden
crate.
e. Have the machine fastened to the forks and forklift, using
metal chain or wire.
Precaution
a. Forks must be fully inserted.
b. L1 must be equal to L2 so that the machine can be in balance.
4-4
4.3.2 Level adjusting
(1) Tools
a. A level scale, with tolerance within 0.02mm/m
b. Spanners, Level adjusting blocks.
(2) Procedure
a. Please ad
j
ust the level ad
j
ustin
g
bolts to
contact the level adjusting blocks.
b
.
Have the level scale put on the worktable.
c. Locate the peak point usin
g
the level scale and
make it as a reference level.
d
.
Ad
j
ust the tolerance of the level ad
j
ustin
g
bolts to be within one
g
rad usin
g
the level
adjusting scale.
1.
The level adjusting bolts.
`
4.3.3 The installation of the electricity
a. Prepare lon
g
enou
g
h wire. (about 30 meters). The diameters for all the models
are as follows:
b. Connect L1L2 and L3 to the main power switch.
c. Connect the ground wire to PE base.
Note: The following are the main power switches and its other relating data.
Power supply AC±10%1Φ
50/60HZ±1HZ
Cross-sectional area of phase
conductors supplying the
equipment` (mm
2
)
Rated current
(A)
Item
Type
220V 380V 415V 440V PE 220V 380V 415V 440V
Power
equipment
capacity
(KVA)
TPR-1230 3.5 3.5 3.5 3.5 3.5 19.3 11.12 10.2 9.7 9.753
TPR-1230H 3.5 3.5 3.5 3.5 3.5 19.7 11.89 11.04 10.33 9.753
TPR-1600H 5.5 5.5 5.5 5.5 5.5 34.8 19.95 18.59 17.38 20.203
TPR-2000H 5.5 5.5 5.5 5.5 5.5 37.8 21.65 21 20 22.193
4.4 The test after installation
a. Have the main power on.
b. Press the emergent stop button to see whether it stops immediately.
c. Power on again.
d Please check whether the motor is running smoothly. If there is any errors,
Please select two of the wires L1, L2 and L3 and change its position.
e Check every mechanism to see whether it works normally.
4.5 The procedure for dismantling the machine
The dismantling procedure is the reverse of the installation one.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Huvema CRDM 3050 X 2000 TOPLINE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Huvema CRDM 3050 X 2000 TOPLINE in de taal/talen: Duits als bijlage per email.

De handleiding is 2,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info