733969
23
Verklein
Vergroot
Pagina terug
1/280
Pagina verder
V-belts
Check every 100 hours of operation. Check for
severe cracking and large nicks.
NOTE: The belt will show some small cracks in
normal operation.
Deck Belt
Deck Belt Removal
Park the mower on a level surface and engage
the park brake. Lower the deck into the lowest
cutting position.
1. Remove foot plate and belt shields.
2. Remove dirt or grass that may have
accumulated around the cutter housings and
entire deck surface.
3. Remove the belt guide hardware with a 1/2"
wrench and set the belt guide aside.
4. With a 1/2" breaker bar and using the square
opening in the idler arm, shift the arm counter
clockwise to relieve the tension on the belt.
5. Carefully lift the belt over the top of the cutter
housing pulleys.
6. Remove the belt from around the electric
clutch on the engine shaft.
Deck Belt Installation
NOTE: For ease in installing the deck belt, refer to
the routing decal on the cutting deck.
1. Place the belt around all the pulleys except
the center spindle pulley.
2. With a 1/2" breaker bar, shift the idler arm
counter clockwise. When there is enough
slack, slip the belt onto the center spindle
pulley.
3. Reinstall the belt guide removed in Step 3
above.
4. Check belt routing to make sure it matches
the routing decal and that the belt does not
have twists.
5. Adjust belt tension by turning the eyebolt nut
until there is approximately 7/8" -1" (22.2 mm -
25.4 mm) of threads showing outside the nut.
6. Belt tension must be set to 60-70 lbs.
7. Replace belt shields on the two mandrel
housings and secure with fasteners.
Cleaning Transaxle Pump and Fans
Dirt or grass accumulating around the transaxle
pump and fans can damage the fans or cause
excessive heat.
1. Push down on the latch lever to release the
seat.
2. Lift and rotate the seat fully forward until
supported by the seat rod.
3. Lift the tab on the fan guard.
4. Blow o debris accumulated around the
transaxle pump and fans.
5. Reinstall fan guard.
6. Supporting the seat, lift seat rod and lower
seat.
Blade Replacement
1. Remove blade bolt by turning it counter
clockwise.
2. Install new or resharpened blade with
stamped GRASS SIDE facing towards
ground/grass (down) or THIS SIDE UP facing
deck and cutter housing.
3. Install and tighten blade bolt securely.
4. Torque blade bolt to 90 ft-lbs (122 Nm).
IMPORTANT INFORMATION Special blade
bolt is heat treated. Replace with a Husqvarna
bolt if required. Do not use lower grade
hardware than specied.
23
MAINTENANCE
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Husqvarna Z560X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Husqvarna Z560X in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 49,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info