595368
36
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
36 – English
MAINTENANCE AND SERVICE
The cutting unit bevel gear
Check the oil level
Check the oil level when the cutting deck is in its lowest
position.
Insert a clean metal rod (approx. Ø3 mm) through the filler
plug. Lower the rod until it reaches the bottom of the gear
housing (approx. 90 mm).
Pull up the metal rod and read off the oil level. The oil level
must be between 18-22 mm from the end of the rod.
Fill with transmission fluid SAE 80W/90 as necessary.
Changing the oil
Empty the bevel gear through the filler plug using a pump
fitted with a plastic tube that extends to the bottom of the
housing.
Alternative: Remove the cutting unit and plastic covers.
Place the cutting unit on its edge and empty the bevel gear
through the plug.
Fill the bevel gear with 80 ml of transmission fluid SAE
80W/90
Checking the engine’s oil level.
Check the oil level in the engine when the Rider stands
horizontal with the engine switched off. Do not check the oil
with the engine running.
Open the engine cover.
Loosen the dipstick, pull it up and wipe it off.
Now insert the dipstick again, without tightening it.
Pull the dipstick out again and read the oil level.
The oil level should be between the markings on the dipstick.
If the level is approaching the ADD mark, top up the oil to
the FULL mark on the dipstick.
The oil filler is on the valve cap.
Tighten the dipstick correctly before starting the engine.
Start and run the engine at idling speed for approx. 30
seconds.
Turn off the motor. Wait 30 seconds and check the oil
level.
If necessary fill so that the oil comes up to the FULL mark
on the dipstick.
The following oil classes are recommended:
API Service Class: CH4 or ACEA E5 or higher.
Choose an oil with viscosity according to the temperature
ranges in the figure:
Do not mix different types of oil.
Replacing the engine oil
The engine oil should be changed the first time after 25 hours
running time. It should then be changed after every 100 hours
of running time.
1 Open the engine cover.
2 Place a container underneath the engine oil drain plug.
3 Remove the dipstick. Remove the drain plug from the
engine.
4 Let the oil run out into the container.
5 Fit the drain plug and tighten it.
6 Change oil filter if necessary.
CAUTION! Too high an oil level increases the risk of oil
leakage.
!
WARNING! Engine oil can be very hot if it is
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
-30 -20 -10 0 10 20 30 40 50 C
-22 -4 -14 32 50 68 86 104 122 F
0W
5W 20
10W 30
20
30
40
15W 40
20W 50
36

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Husqvarna P 520D - 2015 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Husqvarna P 520D - 2015 in de taal/talen: Engels als bijlage per email.

De handleiding is 12,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Husqvarna P 520D - 2015

Husqvarna P 520D - 2015 Gebruiksaanwijzing - Nederlands - 48 pagina's

Husqvarna P 520D - 2015 Gebruiksaanwijzing - Deutsch - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info