609910
25
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
1-25
Set it Up
Set Menu
In the Set Menu, all machine settings are displayed
and set. You can override automatic settings and
make manual adjustments. Simply check the boxes
to activate a function, or touch the corresponding
buttons to open settings.
Sensor Foot Auto
The default setting is “auto”. Stopping with the needle
down the presser foot raises to pivot position. On
“manual” (box is not checked), the foot stays on the
fabric when stopping with needle down. Touch
to raise foot to pivot position.
Sensor Foot defaults to active when Designer SE
Limited Edition is turned on.
FIX Auto
On auto (default) setting, each stitch begins with À x
tie-off stitches. On manual, touch
to tie off.
FIX Auto is always active when Designer SE Limited
Edition is turned on.
Cut jump stitches
The Designer SE Limited Edition features the
automatic function Cut jump stitches. This function
saves you time trimming after the embroidery
is completed. The default setting is on. As you
embroider, the Designer SE Limited Edition will trim
the top jump stitch thread and pull the thread end to
the underside of the fabric.
NOTE: The Designer SE Limited Edition will also cut the
thread after you have changed to a new color. Hold the
thread end when you start embroidering again, so that you
can easily remove the thread end when cut.
Only designs marked “Cut jump stitch trim
command for Designer SE” are programmed for
Cut jump stitches. Jump stitch trim commands can
be added to any design using the Husqvarna Viking 4D
Software. Instructions can be found in the
4D Design Enhancer within the 4D Stitch Editor Module.
Some embroidery designs you purchase may have trim
commands in them. To check this, look at the design in
Stitch Editor to see the trim command symbol in the design
or you can stitch them out.
Selective Thread Cutter Auto
On auto (default) setting, the threads are cut
automatically and the presser foot raises after a Sensor
buttonhole or eyelet is sewn, at color changes or when
an embroidery is À nished. On manual, threads are not
cut after these stitches.
Twin Needle
Opens a list for twin needle width selection. When the
twin needle size is selected, the width of all stitches is
limited for the needle size to prevent needle breakage.
The adjustments are kept until you set the twin needle
selection to “off ”. When a twin needle size is set, a
pop-up is shown when turning on your Designer SE
Limited Edition, and another one when selecting a
stitch that is too wide for the set twin needle size. The
stitch width is automatically adjusted to À t the twin
needle setting. Close the pop-up by touching
.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Husqvarna Designer SE - Limited Edition bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Husqvarna Designer SE - Limited Edition in de taal/talen: Engels als bijlage per email.

De handleiding is 6,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Husqvarna Designer SE - Limited Edition

Husqvarna Designer SE - Limited Edition Gebruiksaanwijzing - Nederlands - 100 pagina's

Husqvarna Designer SE - Limited Edition Gebruiksaanwijzing - Deutsch - 100 pagina's

Husqvarna Designer SE - Limited Edition Gebruiksaanwijzing - Français - 100 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info