2. Use the arrow buttons and the OK button to
move through the menu structure
Settings > Lawn
Coverage > Area > Disable
.
3. Push the OK button.
4. Push the BACK button.
To reset the Lawn Coverage settings
You can reset the
Lawn Coverage
settings for each area
and use the factory setting.
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 21
.
2. Use the arrow buttons and the OK button to
move through the menu structure
Settings > Lawn
Coverage > Area > More > Reset
.
3. Push the OK button.
3.12.8.2 Methods for the product to find the charging
station
The product has 3 search methods to find the charging
station:
• Irregular - The product operates in the work area
until it finds the signal of the charging station.
• Guide wire - The product operates in the work area
until it finds the signal of the charging station or
the guide wire. If it finds the guide wire the product
moves along the guide wire to the charging station.
• Boundary wire - The product moves in the work
area until it finds the signal of the charging station,
the guide wire or the boundary wire. If it finds
the boundary wire, the product moves along the
boundary wire to the charging station.
The factory setting is set to mix the 3 search methods.
When the battery is low the product starts to search for
the charging station with the irregular method for 3 min.
After 3 min the product changes search method to the
guide wire method. After 11 min the product changes
search method to the boundary wire method.
You can change the settings for how the product finds
the charging station to adapt to the work area.
To set how the product finds the charging station
You can make manual settings to make the product
search for the guide wire or the boundary wire in 0–30
min from when the battery is low.
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 21
.
2. Use the arrow buttons and the OK button to move
through the menu structure
Installation > To find
the charging station > Overview of search methods
> Guide
.
3. Push the arrow buttons to select 1 of the guide
wires.
4. Push the number buttons to set the time.
5. Push the OK button.
6. Push the BACK button.
7. Use the arrow buttons and the OK button to move
through the menu structure
Installation > To find
the charging station > Overview of search methods
> Boundary wire
.
8. Push the number buttons to set the time.
9. Push the OK button.
10. Push the START button and close the hatch.
To do a test of the guide wire
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 21
.
2. Use the arrow buttons and the OK button to move
through the menu structure
Installation > Find
charging station > Guide > More > Test guide
.
3. Put the product 3 m / 9 ft. from the guide wire,
facing the guide wire.
4. Push the START button and close the hatch.
5. Make sure the product follows the guide wire to the
charging station.
6. Make sure the product docks with the charging
station.
7. If the product does not dock with the charging
station, change the position of the charging station
or the guide wire. Refer to
To install the charging
station on page 18
and
To install the guide wire on
page 18
.
To do a test of the boundary wire
1. Put the product 3 m / 9 ft. from the boundary wire,
facing the boundary wire.
2. Do steps 1–3 in
To get access to the menu in the
display of the product on page 21
.
3. Use the arrow buttons and the OK button to move
through the menu structure
Installation > Find
charging station > Overview of search methods >
Boundary > More > Test right / Test left
.
4. Push the START button and close the hatch.
5. Make sure the product follows the boundary wire to
the charging station.
6. Make sure the product docks with the charging
station.
7. Change the position of the charging station or the
boundary wire if the product does not dock with the
charging station. Refer to
To install the charging
station on page 18
and
To install the guide wire on
page 18
.
To change the signal range of the charging station
1. Do steps 1–3 in
To get access to the menu in the
display of the product on page 21
.
2. Use the arrow buttons and the OK button to move
through the menu structure
Installation > Find the
charging station > Overview of search methods >
Charging station range
.
3. Use the left arrow button to select
MAX, MID, MIN
.
26 - Installation 1650 - 005 - 17.03.2022
