685866
6
Verklein
Vergroot
Pagina terug
1/17
Pagina verder
SEN C P 1 2 3 4 5 6 7 8
RST
24VAC
BAT
Battery Compartment
SEN C P 1 2 3 4 5 6 7 8
RST
24VAC
BAT
Valve Common Wire
Valve 1
Valve 2
Valve 3
Valve 4
Valve
Wires
Master Valve
Master Valve Wire
Lithium Battery
Battery
Holder
(--)
(+)
ENG
4
REPLACING THE BATTERY
A high-energy lithium battery is included with your
XC controller. The battery allows the user to remotely
program the controller without connecting AC power.
It is also used to keep the current time and day during
power outage conditions. To replace the battery:
1. Remove the screw from the battery holder.
2. Slide the battery holder down to
access the battery.
3. Remove and replace the new battery
into the battery holder and reinstall the
battery holder.
NOTE: This positive(+) side of the battery should face
the inside of the battery holder.
Battery type: CR2032 3V
CONNECTING A MASTER VALVE
NOTE: Complete this section only if you have a master
valve installed in your irrigation system. A master valve
is a "normally closed" valve installed at the supply point
of the main line that opens only when the controller
initiates a watering program.
1. At the Master Valve,
attach the common wire
to either solenoid wire
of the valve. Attach a
separate control wire to
the remaining solenoid
wire.
PSR Series
Pump Start Relay
4.5 Meters Minimum (15')
To Pump
RUN TIMES
CURRENT TIME/DAY
WATER DAYS
START TIMES
RUN
SEASONAL ADJUSTMENT
ALL
MANUAL-ALL STATIONS
SYSTEM OFF
1
MANUAL-ONE STATION
ACTIVE
SENSOR BYPASS
XC
CONNECTING A PUMP START RELAY
NOTE: Complete this section only if you have a pump
start relay installed. A pump start relay is a device that
uses a signal from the controller to actuate a separate
electrical circuit to energize a pump to provide water to
your system.
The controller should be mounted at least a 15 ft (4.5 m) away from
both the pump start relay and pump to minimize any potential electri-
cal interference.
1. Route a pair of wires from the pump relay into the controller.
2. Connect a common wire to the C (Common) terminal inside the
controller and connect the remaining wire from the pump start
relay to the P terminal.
Relay holding current draw must not exceed .30 amps. Do not connect
the controller directly to the pump or damage to the controller will result.
2. The common wire should be attached to the C terminal inside the
controller. The other wire coming from the master valve should be
attached to the P terminal inside the controller. Tighten each termi-
nal screw.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hunter XC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hunter XC in de taal/talen: Engels als bijlage per email.

De handleiding is 3,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Hunter XC

Hunter XC Snelstart handleiding - Nederlands - 1 pagina's

Hunter XC Gebruiksaanwijzing - Nederlands - 12 pagina's

Hunter XC Gebruiksaanwijzing - Deutsch - 17 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info