685893

Hunter Wireless Rain-Clik - Rain Sensor Handleiding

2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Wireless Rain-Clik
™
Rain Sensors
Installation Instructions
Hunter Industries Incorporated • The Irrigation Innovators
© 2004 Hunter Industries Incorporated
U.S.A.: 1940 Diamond Street • San Marcos, California 92078 • TEL: (1) 760-744-5240 • FAX: (1) 760-744-7461
www.HunterIndustries.com P/N 715182 23-461 7/04
Receiver Installation, Other Controllers (continued):
C. 24 Volt Solenoid Valves with Booster Pump (See Figure 5)
Locate the common wire to the
solenoid valves and the common wire
leading to the coil of the relay that
starts the pump. If these two wires are
connected to the “common” terminal
on the controller, disconnect both
of them.
Twist together these two wires along
with one wire from the Rain-Clik™,
and secure with a wire nut. Attach
the other wire of the Wireless Rain-
Clik™ receiver to the “common”
terminal on the controller. Note: The
pump circuit output must be 24 Volts
in this situation. Do not proceed
if 110V.
SETTING THE TRANSMITTER ADDRESS AT THE RECEIVER
Units purchased as a kit will already have their address learned.
No addressing is necessary, however if the receiver or transmitter is
replaced, you need to reset the address.
Each transmitter produced has a unique address hard-coded into it. A receiver
must learn this address to work with that transmitter. This step will only be
necessary if transmitters and receivers are purchased separately.
1. Prior to applying power (yellow wires) to the receiver, press and hold the
pushbutton on the receiver.
2. While the pushbutton is being held apply power to the receiver–the
receiver’s “sensor status” LED should light up yellow indicating the receiver
is ready to learn an address.
3. Push and hold the quick response post on the transmitter/sensor.
4. Within 4 seconds, the receiver’s “sensor status” LED should turn red.
5. Release the transmitter/sensor’s quick response post and within 4 seconds
the LED on the receiver should turn green. The address is now learned and
will be retained even in the event of a power outage.
OPERATION
The receiver has two LEDs, which indicate the state of the system. The
STATUS LED will be RED when the sensor is wet (watering disabled), and
GREEN when the sensor is dry (watering enabled). There is also a RED
BYPASS LED on the receiver. If this LED is lit, the rain sensor is bypassed
and watering will always be allowed. Even though the sensor is bypassed, the
STATUS LED will continue to alert you of the state of the sensor (Wet or Dry).
ADJUSTMENTS AND OPERATION
The Wireless Rain-Clik can keep the irrigation system from starting or
continuing after rainfall or freezing conditions (Wireless Rain/Freeze-Clik).
The time that it takes the Wireless Rain-Clik to reset for
normal sprinkler operation after the rain has stopped
is determined by weather conditions (wind, sunlight,
humidity, etc.). These conditions will determine how fast
the discs dry out, and since the turf is also experiencing
the same conditions, their respective drying rates will
roughly parallel each other.
There is an adjustment capability on the Wireless Rain-
Clik that will slow down the reset rate. By closing the
“vent” (see Figure 6) to completely or partially cover
the ventilation slots, the discs will dry more slowly.
This adjustment can compensate for an “overly sunny” installation location, or
peculiar soil conditions. Experience will best determine the ideal vent setting.
No adjustment is required for the freeze sensor portion of the wireless
Rain/Freeze-Clik. The Wireless Rain/Freeze-Clik will automatically disable
the Irrigation system when temperatures fall below 37°F. Although Freeze
Sensors are designed to automatically prevent watering near or below freezing
conditions, visual checks and prudent manual watering suspensions should be
used in conjunction with any freeze sensor
BYPASSING THE SENSOR
The sensor may be bypassed by using the built in bypass feature in the SRC,
Pro-C or ICC. On other controllers the sensor may be bypassed by pressing the
“BYPASS” button on the receiver. The RED BYPASS LED on the receiver will be
lit when the sensor is bypassed. Pressing the “BYPASS” button again will cause
the RED BYPASS LED to go back out thus re-enabling the sensor.
Battery Life: The Wireless Rain-Clik transmitter is designed to work daily for
up to 12 years with the maintenance-free battery. The sealed unit is available
as a replacement part. Should you need to change the transmitter the receiver
will have to learn the new transmitter address.
There is no required maintenance for the unit. The Wireless Rain-Clik does not
have to be removed or covered for “winterizing” purposes.
TROUBLESHOOTING
Follow these simple checks first before assuming the unit is bad and replacing it.
System will not come on at all:
A. First, check to see that the Wireless Rain-Clik discs are dry and the switch
“clicks” on and off freely by pressing the top of the spindle.
B. Next, look for breaks in the wire leading to the Wireless Rain-Clik receiver
and check all wire junctions.
C. Verify temperature (for Rain/Freeze-Clik installations).
System will not shut off even after heavy rainfall:
A. Check wiring for correctness (see section on wiring to your irrigation system).
B. Is the rainfall actually hitting the Wireless Rain-Clik? Check for obstructions
to rainfall such as overhangs, trees or walls.
Manufactured under U.S. Patent 6,570,109 B2
All Rain-Clik models are listed by Underwriters Laboratories, Inc. (UL). Samples of these devices have
been evaluated by UL and meet the applicable UL standards for safety.
FCC Compliance Notice
This notice applies only to models WRC-TR and WRFC-TR
This device complies with FCC rules Part 15. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference and
2) This device must accept any interference that may be received, including
interference that may cause undesired operation
Transmitter FCC ID: M3UWSSTX
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generated, uses and can radiate
radio frequency energy and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry of Canada Notice
This notice applies only to models WRC-TR and WRFC-TR
IC: 277A-14198
WRC-R: This Class B digital apparatus complies with Canadian ICES-003.
The term “IC:” before the certification/registration number only signifies that the
Industry of Canada technical specifications were met.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
CE Notice: this notice applies only to models WRC-INT.
Important Notice:
Low power RF product operating in 433.92MHz band for
indoor or outdoor home and commercial use.
AUS B DK FIN Member states in the EU with
restrictive use for this product are
crossed out.
F D GR IRE
I LUX NL P
E S UK
Figure 5
Normally-
Open Rela
y
1 2 3 4
Controller
C
Solenoid
Valves
Common
Wire to All
Valves
Pump
or
MV
Line-In
Line-Out (to Pump)
Wireless
Rain Sensor
AC AC
Y
Y
W
B
Red light indicates
sensor is bypassed
GREEN = Sensor is dr
y
RED = Sensor is we
t
SENSOR BYPASS
SENSOR STATUS
WIRELESS
RAIN SENSOR
RAIN SENSOR
Press to bypass, press
again to re-enabl
e
Figure 6
Vent Ring
Vents
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hunter Wireless Rain-Clik - Rain Sensor bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hunter Wireless Rain-Clik - Rain Sensor in de taal/talen: Engels als bijlage per email.

De handleiding is 0,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info