685886
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
SEN
C 1 2 3 4 5 6
MV
RST
24VAC
24VAC
9 VOLT
ALKALINE
BATTERY
Valve 1
Valve 2
Valve 3
Valve 4
Weather Sensor
MasterValve
AM
%
PM
24
Eco-Logic 4-& 6-Station Indoor Controller
Owners Manual and Programming Instructions
Installation Instructions
Remove lower access cover. Place a screw into the wall and hang the controller from the
keyhole on the back. Secure the controller using one or more screws below the terminal
strip. One wire from each solenoid should be connected to the C terminal (common wire).
The other wire from each solenoid to its respective number on the terminal strip. Connect
the transformer wires to the 24 VAC terminal strip. Attach the two sensor wires (if needed)
to the SEN terminals. Connect a 9-volt alkaline battery (not included) to the battery wire
clip. Plug the transformer into a nearby power outlet.
Main Display
Current Time/Day Set current day and time.
Start Times Set 1 to 4 start times for each program.
Run Times Set each valve station run time from 1 min. to 4 hrs.
Water Days Select specific days to water, odd/even days, or a selected number
of days between waterings (interval).
Seasonal Adjustment Make run time changes according to the seasons without
reprogramming the controller.
System Off Stops all automatic watering.
Program Designator identifies program in use (A or B).
Flashing Sprinkler indicates that watering is occurring.
Umbrella indicates rain sensor is suspending irrigation.
Crossed Umbrella Indicates rain sensor has been manually bypassed.
identifies month when programming current date.
identifies day when programming current date.
1
Manual Single Station indicates the one time watering of a single valve station.
Manual All Station indicates the one time watering of all valve stations or selected
stations.
Control Buttons
Button increases displayed item.
Button decreases the displayed item.
Button advances to the next item.
Button advances to the previous item.
Button Select program A or B for different watering requirements.
Mode Button Advanced through programming functions.
Programming the Controller
An irrigation program consists of three parameters:
1) A program start time, 2) watering duration for each station and 3) days to water. A
program will run all stations assigned to it in sequential order. Programs are independent
and stations can be assigned to both programs.
Setting the Current Date and Time
1. Press the Mode button until the arrow is pointing at the Current Time/Day
position.
2. The year will be flashing. Use the or buttons to change the year. Press the
button to proceed to setting the month.
3. The month will be flashing and the
icon will be displayed. Use the or
buttons to change the month. Press the button to proceed to setting the day.
4. The day will be flashing and the icon will be displayed. Use the or but-
tons to change the day. Press the button to proceed to setting the time.
5. The time will be displayed. Use the and buttons to select AM, PM, or
24 hour. Press the button to set the hour.
A
B
AM
%
PM
24
1
System Off
Water Days
Seasonal
Adjustment
Current
Time/Day
Run Times
Start Times
6. Hours will be flashing. Use the and buttons to change the hour shown. Press
the button to move to minutes.
7. Use the and buttons to change the minutes shown. The date, day and time
have now been set.
Setting the Program Start Time(s)
NOTE: One start time will activate all stations sequentially in that program. This
eliminates the need to enter each stations start time. Multiple start times in a
program can be used for separate morning, afternoon, or evening watering cycles.
1. Press the
Mode button until the arrow is pointing at Start Times .
2. Program A will be displayed. (If Program B is desired, press the button).
3. Use the or buttons to change the start time.
4. Press the button to add an additional start time, or button for the next
program.
Eliminating a Program Start Time
With the arrow pointing at the Start Times position, press the or buttons until
you reach 12:00 AM. Push the button once to reach the OFF position.
Setting Station Run Times
1. Press the Mode button until the arrow is pointing at Run Times
.
2. Use the button to select a program (A or B).
3. Press the or buttons to change the station run time from 1 minute to 4 hours.
Press the button to advance to the next station.
Setting Days to Water
1. Press the Mode button until the arrow is pointing at Water Days .
2. Use the button to select the desired program.
3. Arrows point at the specific days of the week in which watering is to occur. Press
the button to activate that day or the button to cancel watering for that day.
Selecting Odd or Even Days to Water
This feature is uses numbered days of the month for watering instead of specific days
of the week (Odd days 1st, 3rd, 5th, etc.; Even days 2nd, 4th, 6th, etc.).
1. When in the Water Days mode, press the button until the cursor is above
either ODD or EVEN on the display.
2. Press the button to select, or the button to cancel either ODD or EVEN days
to water.
Selecting Interval Watering
You can select interval watering from 1 to 31 days.
1. When in the Water Days mode, press the
button until the cursor is over INT.
Press the button and the interval watering icon
will be displayed and
a 1 will be flashing.
2. Press the or button to select the number of days between watering days
(1 to 31 days). This is called the interval.
The controller will water the selected program at the next start time and will then
water at the interval programmed.
Seasonal Adjustment
Seasonal Adjustment is used to make global run time changes without re-program-
ming the entire controller.
1. Press the Mode button until the arrow is pointing at Seasonal Adjustment .
2. Press the or buttons to adjust the percentage of the seasonal adjustment
from 10% to 150%.
NOTE: The controller should always be initially programmed in
the 100% position.
System Off
To turn your controller off, press the Mode button until the arrow is pointing at
the System Off . Wait 2 seconds and the display will read OFF. Valves currently
watering will be shut off. All active programs will be discontinued and watering
stopped. To return the controller to normal automatic operation, simply press the
Mode button once. The current time and day will be displayed.
Programmable Off
This feature will stop all programmed waterings for a designated period of time from
1 to 7 days. After the programmed off period, the controller will automatically resume
programmed watering.
1. Press the Mode button until the arrow is positioned next to the System Off
function.
2. Wait 2 seconds until OFF is displayed.
3. Press the button to set the number of days off (up to 7 days).
PROBLEM CAUSES SOLUTIONS
Display indicates watering but none
is occurring.
Faulty or miswired valve.
Faulty pump or pump relay.
No water pressure to system.
Check valve and valve wiring.
Check pump and pump relay. Replace if defective.
Turn on main system water supply.
Time of day display is blinking. Unit has just been powered up for the first time.
Extended power outage has occurred that has drained
backup battery.
Set time/date.
Replace battery and reprogram controller.
Valve will not turn on. Short in wire connections.
Bad solenoid.
Check wiring for short or faulty wire connections.
Replace solenoid.
Display shows “ERR” with a number (1-6). Short in valve wiring circuit; or a faulty solenoid
on the station number indicated.
Check wire circuit or solenoid for the valve number indicated. Repair short
or replace solenoid. Press any button to clear “ERR” display.
Display shows “P ERR”. Faulty pump relay or master valve wiring.
Incompatible or defective pump relay.
Check wiring to relay or master valve solenoid. Press any button to clear
“P ERR” from the display.
Check electrical specifications of pump relay. Replace if defective.
The display reads “No AC”. There is no AC power present. Check to make sure power is on. Check to see if transformer is properly
installed.
Rain Sensor does not suspend irrigation. Rain sensor is defective or miswired.
Jumper not removed.
Verify operation of sensor and proper wiring.
Remove jumper.
Frozen Display, or display showing incorrect
information.
Power surge. Reset controller per “Clearing Controllers Memory/Resetting
the Controller”.
Automatic irrigation does not start at start time and
controller is not in the system off mode.
AM/PM of time of day not set correctly.
AM/PM of start time not set correctly.
Start time is disabled (Set for Off).
Controller is not receiving AC power.
Correct AM/PM of time of day.
Correct AM/PM of start time. Set start time.
See “Setting Watering Start Times”.
Check AC connections.
Controller waters the same area more than
one time/Controller cycles continuously.
Too many start times entered in program (user error). One start time activates a complete cycle. See Setting Watering
Start Times”.
Troubleshooting Guide
Automatic Watering
After all programming has been completed, press the Mode button until the time of
day is displayed. This will enable automatic execution of all selected watering programs
and start times.
Manual Run – All Stations
Manual All Stations allows the operation of valves assigned to a program in sequen-
tial order.
1. Press and hold the
button for three seconds. The will be displayed, along with the
program letter. A station number will also be displayed.
2. Select program by pressing the
button.
3. Use th
e or buttons to select the amount of time for the station to water if
different from the run time displayed.
4. Use the
button to move to the next station.
5. Repeat steps 3 and 4 until you reach the station at which you want
watering to begin.
After 2 seconds of inactivity, manual watering will begin and sequence through each
valve of the entire program. Once manual watering has been completed, the controller
will automatically return to the automatic mode with no change in the previously set
program.
Manual Run – Single Station
1
Manual Single Station function allows the for operation of a single valve.
Sensor Bypass
The sensor can be bypassed to allow manual operation when the sensor has deacti-
vated the system.
1. Press the
button for two seconds ON will be displayed.
2. Press the button to bypass the rain sensor. OFF will be displayed.
Clearing the Controller’s Memory / Resetting the Controller
If you feel that you have misprogrammed your controller, there is a process that will
reset the memory to the factory defaults and erase all programs and data that have
been entered into the controller.
1. Press and hold the ,
, and buttons.
2. Press and release the reset button located in the lower wiring compartment.
3. Wait 2 seconds and release the , , and buttons. The display should now
show 12:00 am. All programmed data has been cleared from memory and the
controller can now be reprogrammed.
Hunter Quick Check Diagnostics
This feature allows you to quickly diagnose wiring problems with your controller.
1. Press the
, , , buttons simultaneously. In the standby mode, the LCD
will display all segments.
2.
Press the button once to begin the Quick Check procedure. Within seconds the
system searches all stations, detecting any circuit problems. When a field wiring
short is detected, an ERR symbol preceded by the station number will flash mo-
mentarily on the display.
Normal/Limited Program Mode
Your controller can be programmed to increase or decrease the watering program
capability.
1. Press and hold the button. Press the button.
2. Release the and the buttons
3. Use the or button to change program modes:
Normal Mode (2 programs/4 start times)
Limited Mode (1 program/1 start time)
Advanced (3 programs/4 start times)
Operating Specifications
2 Independent Watering Programs
Station Run Time: 0 to 4 hours in 1-minute increments
Start Times: 4 per day, per program, for up to 12 daily starts
Watering Schedule: 365-day calendar, odd/even, or interval (1 to 31 days).
Simple manual operation
Seasonal adjustment (10% to 150%)
Programmable rain delay (1 to 7 days)
Electrical Specifications
Transformer input 230VAC 50/60 Hz
Transformer output: 24VAC .625 amp.
Station Output: .56 amp.
Battery 9-volt (not included) for backup timekeeping
Electronic short circuit protection
Non-volatile memory for program data
CE approved
Certificate of Conformity to European Directives
Hunter Industries declares that the irrigation controller Eco-Logic complies with
the standards of the European Directives of electromagnetic compatibility
87/336/EEC and low voltage 73/23/EEC.
__________________________________
Project Engineer
Hunter Industries Incorporated • The Irrigation Innovators
Internet: www.HunterIndustries.com INT-575 11/06
1

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Hunter-Eco-Logic
  • Heb de gebruiksaanwijzing 100 keer gelezen maar het lukt me nog steeds niet om het waterprogramma dat voor 4 sectoren moet werken, slechts eenmaal te laten sproeien. Het programma herhaalt zich ongevraagd zeker twee keer per avond. Hoe te handelen, resetten, maar hoe dan. Gesteld op 22-7-2024 om 10:49

    Reageer op deze vraag Misbruik melden
  • Krijg de computer niet geregeld.Als het avond programma draait, herhaalt hij dat zeker twee keer. Kost me te veel water. Kan het aparaat gereset worden en hoe dan. Gesteld op 22-7-2024 om 10:45

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hunter Eco-Logic bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hunter Eco-Logic in de taal/talen: Engels als bijlage per email.

De handleiding is 1,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Hunter Eco-Logic

Hunter Eco-Logic Gebruiksaanwijzing - Deutsch - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info