685908
15
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
Built on Innovation
®
15
Basic Programming and Setup
INTELLIGENT CURRENT SENSING
ACC2 has no articial programming limits preventing
overlapping programs and stations. The controller senses
how much electrical current is being drawn, and will suspend
stations automatically if the combined current threatens the
transformer.
It is also possible to set controller and station limits (Stations,
Station Limits) to control how many outputs may operate at
once.
A conventionally wired ACC2 may run as many as 14 Hunter
solenoids (including any P/MV outputs) simultaneously before
suspending additional stations. Environmental factors or
higher-draw solenoids may cause the overcurrent protection
to activate at lower station counts.
It is possible to view the current draw of each station in the
Diagnostics menu.
RUN TIMES
You can access Run Times from the programming menu, or
from the so key shortcuts from the Start Times screen. This
allows you to set up an entire program (start times, run times,
and water days) from the same menu.
Verify that you are in the correct program, by number or
name.
Select the Run Type eld, and select Station or Block (“Blocks”
are described in detail in the Stations Menu section. Blocks
replace “SSGs” in the original ACC). Press the dial to select the
type.
Dial to the Number eld. Press and dial to select station or
block number. Press to enter.
Dial to the Run Time eld, press to select, and dial to enter the
run time (from 1 minute to 12 hours). You can also enter run
times in seconds, by dialing to the: SS eld (seconds), which is
adjusted separately.
You may continue to enter any station numbers, in any order,
in the same way.
Show Edit Tools (Shortcuts): Press the so key for Show Edit
Tools. If you are running stations in numerical order, you can
use the so key for Fill Down. This will automatically add 1 to
the previous station number, and copy the run time on the
next line. For example, if you entered Station 1, 5 minutes, and
then pressed Fill Down, it would add Station 2 for 5 minutes
on the next line. This is a shortcut for copying sequential run
times very quickly.
You can also Delete any item from the list. Scroll to the item,
and press Delete.
You can also Insert an item above any selected line in the list.
Scroll to an item, and press Insert Line, and a blank line will
appear above it.
ACC2 can run any station or block in any order. Example: you
could insert station 3 between stations 1 and 2. The program
would run 1, 3, 2, in that order.
Adjusted Run Times: The Adjusted Run Times show the
eects of the current Seasonal Adjust settings on the base
run time. If a run time is set to 10 minutes, but Seasonal
Adjust is at 50%, the Adjusted Run Time will show 5 minutes.
The Seasonal Adjust amount is not changed in this screen,
but can be set from the Programs menu, or automatically by a
Solar Sync sensor.
When all the Run Times for the program have been set, press
Back or Home to exit.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hunter ACC-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hunter ACC-2 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Hunter ACC-2

Hunter ACC-2 Snelstart handleiding - Deutsch - 52 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info