522346
42
Verklein
Vergroot
Pagina terug
1/160
Pagina verder
32
Transom Mount - Side Imaging®
Routing the cable
The transducer cable has a low profile connector that must be routed to the
point where the control head is mounted. There are several ways to route the
transducer cable to the area where the control head will be installed. The
most common procedure routes the cable through the transom into the boat.
NOTE: Your boat may have a pre-existing wiring channel or conduit that you can
use for the transducer cable.
1. Unplug the other end of the transducer cable from the control head.
Make sure that the cable is long enough to accommodate the
planned route by running the cable over the transom.
CAUTION! Do not cut or shorten the transducer cable, and try not to damage the
cable insulation. Route the cable as far as possible from any VHF radio antenna
cables or tachometer cables to reduce the possibility of interference. If the cable
is too short, extension cables are available to extend the transducer cable up to
a total of 50' (15 m). For assistance, contact the Customer Resource Center at
humminbird.com or call 1-800-633-1468 for more information.
NOTE: Since the transducer may need to pivot up to 90° in the bracket if it strikes
an object, make sure there is sufficient cable slack to accommodate this motion.
It is best to route the cable to the side of the transducer so the cable will not be
damaged by the rotation of the transducer.
2. If you will be routing the cable through a hole in the transom, drill a
5/8" diameter (16 mm) hole above the waterline. Route the cable
through this hole, then fill the hole with marine-grade silicone
sealant and proceed to the next step immediately.
3. Place the escutcheon plate over
the cable hole and use it as
a guide to mark the two
escutcheon plate mounting
holes. Remove the plate, drill
two 9/64" (3.5 mm) holes, then
fill both holes with marine-
grade silicone sealant. Place the
escutcheon plate over the cable
hole and attach with two #8 x
5/8" (16 mm) wood screws.
4. Route and secure the cable by
attaching the cable clamp to the
transom; drill one 9/64" dia. (3.5
mm) x 5/8" deep (16 mm) hole,
then fill hole with marine-grade
silicone sealant, then attach the
cable clamp using a #8 x 5/8"
(16 mm) screw.
5. Plug the other end of the
transducer cable back into the
control head connection holder.
Testing the installation
After transom transducer installation, please perform the final testing and then
finalize the installation (see Test and Finish the Transducer Installation).
5/8” Hole
Escutcheon
Plate
Cable Clamp
Routing the Cable
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Humminbird 858C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Humminbird 858C in de taal/talen: Engels als bijlage per email.

De handleiding is 12,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info